TestRpt_Power Density_appendix C_0213

FCC ID: IHDT56XL1

RF Exposure Info

Download: PDF
FCCID_4168380




Measurement Report for 30 GHz Verification Source, FRONT (SCREEN), Validation, UID 0 -, Channel 30000 (30000.0MHz) Device under Test Properties Name, Manufacturer Dimensions [mm] IMEI DUT Type , 30 GHz Verification Source 100.0 x 100.0 x 100.0 Bar/Brick Exposure Conditions Phantom Section Position, Test Distance Band Group, Frequency [MHz], Conversion Factor [mm] UID Channel Number 5G - FRONT (SCREEN), Validation CW, 30000.0, 1.0 5.55 mm 0-- 30000 Hardware Setup Phantom Medium Probe, Calibration Date DAE, Calibration Date 5G Phantom V0.1- xxxx Air --- EUmmWV2 - SN9374, 2018-03-23 DAE4 Sn1215, 2018-02-26 Scan Setup Measurement Results 5G Scan 5G Scan Grid Extents [mm] 60.0 x 60.0 x 2.5 Date 2018-04-06, 16:36 Grid Steps [mm] 2.5 x 2.5 Avg. Area [cm2] 1.00 Sensor Surface [mm] 5.55 Savg [W/m2] 39.8 MAIA MAIA not used Speak [W/m2] 54.8 Epeak [V/m] 133 Hpeak [A/m] 0.413 Power Drift [dB] -0.09 Warning(s) / Error(s) Details Area Scan Warning(s) Error(s)




Measurement Report for Device, FRONT, Validation band, UID 0 -, Channel 30000 (30000.0MHz) Device under Test Properties Name, Manufacturer Dimensions [mm] IMEI DUT Type , Device 100.0 x 100.0 x 100.0 Phone Exposure Conditions Phantom Section Position, Test Distance Band Group, Frequency [MHz], Conversion Factor [mm] UID Channel Number 5G - FRONT, Validation band CW, 30000.0, 1.0 5.55 0-- 30000 Hardware Setup Phantom Medium Probe, Calibration Date DAE, Calibration Date 5G Cover- xxxx --Air- EUmmWV2 - SN9374, 2018-03-23 DAE4 Sn1215, 2018-02-26 Scan Setup Measurement Results 5G Scan 5G Scan Grid Extents [mm] 60.0 x 60.0 Date 2018-06-26, 14:38 Grid Steps [lambda] 0.25 x 0.25 Avg. Area [cm2] 1.00 Sensor Surface [mm] 5.55 pStot avg [W/m2] 46.1 MAIA MAIA not used pSn avg [W/m2] 45.7 Epeak [V/m] 141 Power Drift [dB] -0.01 Warning(s) / Error(s) Details 5G Scan Warning(s) Error(s)

Calibration Laboratory of Schmid & Partner s Schweizerischer Kalibrierdienst C Service suisse d'etalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland s Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Sporton Certificate No: EUmmWV2-9388_Apr18 CALIBRATION CERTIFICATE I Object EUmmWV2 - SN:9388 Calibration procedure(s) QA CAL-02.v8, QA CAL-25.v6, QA CAL-42.v2 Calibration procedure for E-field probes optimized for close near field evaluations in air Calibration date: April 10, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)"C and humidity< 70%. Calibration Equipment used (M& TE critical for calibration) Primary Standards ID Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04-Apr-18 (No. 217-02672/02673) Apr-19 Power sensor NRP-Z91 SN: 103244 04-Apr-18 (No. 217-02672) Apr-19 Power sensor NRP-Z91 SN: 103245 04-Apr-18 (No. 217-02673) Apr-19 Reference 20 dB Attenuator SN: S5277 (20x) 04-Apr-18 (No. 217-02682) Apr-19 Reference Probe ER3DV6 SN: 2328 10-0ct-17 (No. ER3-2328 Oct17) Oct-18 DAE4 SN: 789 2-Aug-17 (No. DAE4-789 Aug17) Aug-18 Secondary Standards ID Check Date (in house) Scheduled Check Power meter E4419B SN: GB41293874 06-Apr- 16 (in house check Jun- 16) In house check: Jun-18 PowersensorE4412A SN: MY41498087 06-Apr-16 (in house check Jun-16) In house check: Jun-18 PowersensorE4412A SN: 000110210 06-Apr-16 (in house check Jun-16) In house check: J un-18 RF generator HP 8648C SN: US3642U01700 04-Aug-99 (in house check Jun-16) In house check: Jun-18 Network Analyzer HP 8753E SN: US37390585 18-0ct-0 1 (in house check Oct-17) In house check: Oct-18 Name Function Signature ~ Calibrated by: Jeton Kastrali Laboratory Technician Approved by: Katja Pokovic Technical Manager ~4- Issued: April 28. 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: EUmmWV2-9388_ Apr18 Page 1 of 27

Calibration Laboratory of Schmid & Partner s Schweizerischer Kalibrierdienst Service suisse d'etalonnage Engineering AG C Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland s Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: NORMx,y,z sensitivity in free space DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A,B,C,D modulation dependent linearization parameters Polarization cp cp rotation around probe axis Polarization S 3 rotation around an axis that is in the plane normal to probe axis (at measurement center), i.e., S = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system 5.ensor Angles sensor deviation from the probe axis, used to calculate the field orientation and polarization k is the wave propagation direction Calibration is Performed According to the Following Standards: a) IEEE Std 1309-2005, "IEEE Standard for calibration of electromagnetic field sensors and probes, excluding antennas, from 9 kHz to 40 GHz", December 2005 Methods Applied and Interpretation of Parameters: • = = NORMx,y,z: Assessed for E-field polarization S O for XY sensors and S 90 for Z sensor (f 5 900 MHz in TEM-cell; f > 1800 MHz: R22 waveguide). For frequencies > 6 GHz, the far field in front of waveguide horn antennas is measured for a set of frequencies in various waveguide bands up to 110 GHz. • DCPx,y,z: DCP are numerfcal ltnearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. • PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics • The frequency sensor model parameters are determined prior to calibration based on a frequency sweep (sensor model involving resistors R. Rp, inductance Land capacitors C, Cp), • Ax,y,z; Bx,y,z; Cx,y,z; Dx,y,z; VRx,y,z: A, B, C, Dare numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. • Sensor Offset: The sensor offset corresponds to the mechanical from the probe tip (on probe axis). No tolerance required. • Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). • Equivalent Sensor Angle: The two probe sensors are mounted in the same plane at different angles. The angles are assessed using the information gained by determining the NORMx (no uncertainty required). • Spherical isotropy (3D deviation from isotropy): in a locally homogeneous field realized using an open waveguide/ horn setup. Certificate No: EUmmWV2-9388_Apr18 Page 2 of 27

EUmmWV2 - SN: 9388 April 10, 2018 Probe EUmmWV2 SN:9388 Manufactured: June 14, 2017 Calibrated: April 10, 2018 Calibrated for DASY Systems (Note: non-compatible with DASY2 system!) Certificate No: EUmmWV2-9388_Apr18 Page 3 of 27

EUmmWV2 - SN: 9388 April 10, 2018 DASY - Parameters of Probe: EUmmWV2 - SN:9388 Basic Calibration Parameters (750 MHz - 3 GHz) Sensor X SensorY Unc (k=2) Norm r.. v11v1ml2\ 0.01971 0.02321 ± 10.1 % DCP (mV)" 105.0 105.0 Equivalent Sensor Angle -59.2 32.2 Calibration results for Frequency Response (6-110 GHz) Frequency Target E-Field Deviation Sensor X Deviation Sensor Y Unc (k=2) GHz Vim dB dB dB 6.6 40.04 -0.09 0.03 + 0.98 dB 8 48.41 -0.39 -0.36 ± 0.98 dB 10 54.41 -0.11 -0.06 + 0.98 dB 15 75.04 -0.02 0.14 + 0.98 dB 18 85.30 0.29 0.17 + 0.98 dB 26.6 96.89 0.38 0.36 ± 0.98 dB 30 92.55 0.32 0.29 + 0.98 dB 35 93.71 0.08 0.09 + 0.98 dB 40 91.46 -0.13 -0.21 + 0.98 dB 50 19.62 0.28 0.19 ± 0.98 dB 55 22.38 0.30 0.24 ± 0.98 dB 60 23.03 0.18 0.04 + 0.98 dB 65 27.40 -0.17 -0.16 ± 0.98 dB 70 23.95 -0.23 -0.27 ± 0.98 dB 75 19.61 -0.24 -0.29 ± 0.98 dB 75 14.11 -0.15 -0.12 + 0.98 dB 80 21.51 -0.30 -0.07 + 0.98 dB 85 22.75 -0.07 0.06 ± 0.98 dB 90 23.84 0.23 0.30 ± 0.98 dB 92 23.93 0.06 0.00 ± 0.98 dB 95 20.55 0.04 0.00 + 0.98 dB 97 24.41 0.15 0.03 + 0.98 dB 100 22.61 0.13 0.06 ± 0.98 dB 105 22.75 0.00 0.02 ± 0.98 dB 110 18.85 -0.38 -0.26 ± 0.98 dB Ca1l'b ration Resu ts for M0 duIat1on • Res ponse UID Communication System Name A B C D VR Max Unccc dB dByµV dB mV dev. (k=2) 0 cw X 0.0 0.0 1.0 0.00 50.4 + 2.5 % ±4.7 % y 0.0 0.0 1.0 22.6 Note: For details on UID parameters see Appendix The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. 8 Numerical linearization parameter: uncertainty not required. E Uncertainty is determined using the max. deviation from If near response applying rectangular distribution and is expressed for the square of the field value. Certificate No: EUmmWV2-9388_Apr18 Page 4 of 27

EUmmWV2 - SN: 9388 April 10, 2018 DASY - Parameters of Probe: EUmmWV2 - SN:9388 sensor Frequency Md o e IParame ters Sensor X SensorY R (0) 38.90 41.13 Rn (Q) 95.86 92.34 L (nH) 0.03220 0.03158 C (pF) 0.2221 0.2600 Cn (pF) 0.1255 0.1212 Sensor Model Parameters C1 C2 a T1 T2 T3 T4 T5 T6 fF IF v-, ms.v-2 ms.v- 1 ms v-2 v-, X 7.692 52.62 30.48 0.916 2.245 4.905 0 0.502 0.997 y 5.836 42.35 33.63 0.916 2.257 4.941 0 0.824 0.999 Other Probe Parameters Sensor Arrangement Rectangular Connector Angle(') 44.0 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 320mm Probe Body Diameter 8mm Tip Length 23mm Tip Diameter 8.0mm Probe Tip to Sensor X Calibration Point 1.5mm Probe Tip to Sensor Y Calibration Point 1.5mm Certificate No: EUmmWV2-9388_Apr18 Page 5 of 27

EUmmWV2 - SN: 9388 April 10, 2018 Deviation from Isotropy in Air f = 30 GHz 30 GHz: JD isotropy, E-field normal to probe axis iii' ~ ..g w 0 a -1.00-- 0 80 Q -0 _80--0 _60 a -0 _60 --0 .40 a -0 .40-·D.20 8 -0.20 ·0 00 C 0,00-0 .20 a0.20-0_40 C 0_4 0-0 _60 Cl 0,60-0.80 a O 80-1 00 30 GHz: 3D isotropy, E-field parallel to probe axis iii' ~ .. 2 '- w a • -1.00--0.80 ti -0.80--0.60 • -0.6(}.-0.40 • -0.40--0 20 • -0.20-0.00 D 0.00-0.20 • 0.20-0.40 D 0.4C>-0.60 D 0.60-0.80 • 0.80-1.00 Probe isotropy for E10 t: probe rotated q> = 0° to 360°, tilted from field propagation direction ii Parallel to the field propagation (\ii =0° - 90°): deviation within ± 0.29 dB Normal to field orientation ( S =0° - 90°): deviation within ± 0.44 dB Certificate No: EUmmWV2-9388_Apr18 Page 6 of 27






Calibration Laboratory of Schmid & Partner s Schweizerischer Kalibrierdienst C Service suisse d'etalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Auden Certificate No: DAE4-918_Jun18 CALIBRATION CERTIFICATE Object DAE4 - SD 000 D04 BK - SN: 918 Calibration procedure(s) QA CAL-06.v29 Calibration procedure for the data acquisition electronics (DAE) Calibration date: June 20, 2018 This calibration certificate documents the traceability to national standards , which realize the physical units of measurements (SI). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards Cal Date (Certificate No.) Scheduled Calibration Keithley Multimeter Type 2001 ISN: 0810278 31-Aug-17 (No:21092) Aug-18 Secondary Standards ID # Check Date (in house) Scheduled Check Auto DAE Calibration Unit SE UWS 053 AA 1001 04-Jan-18 (in house check) In house check: Jan-19 Calibrator Box V2.1 SE UMS 006 AA 1002 04-Jan-18 (in house check) In house check: Jan-19 Name Function Signature Calibrated by: Eric Hainfeld Laboratory Technician ~;>~ Approved by: Sven Kuhn Deputy Manager Issued: June 20, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE4-918_Jun18 Page 1 of 5

Calibration Laboratory of $ Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d'etalonnage Engineering AG C Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland s Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters • DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. • Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. • The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. • DC Voltage Measurement Linearity: Verification of the Linearity at + 10% and -10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. • Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. • Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. • AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage • Input Offset Measurement Output voltage and statistical results over a large number of zero voltage measurements. • Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. • Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto-zeroing and during measurement. • Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. • Power consumption: Typical value for information . Supply currents in various operating modes. Certificate No: DAE4-918_Jun18 Page 2 of 5

DC Voltage Measurement AID - Converter Resolution nominal High Range: 1LSB = 6.1µV , full range= -100 ... +300 mV Low Range: 1LSB = 61 nV , full range= -1.. .....+3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X y z High Range 404.292 ± 0.02% (k=2) 404.471 ± 0.02% (k=2) 404.000 ± 0.02% (k=2) Low Range 4 .01048 ± 1.50% (k=2) 3.99008 ± 1 .50% (k=2) 4.00845 ± 1.50% (k=2) Connector Angle Connector Angle to be used in DASY system 320.5 ° ± 1 ° Certificate No: DAE4-9 18_Jun18 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) I 1. DC VotaQe L"meantv High Range Reading (µV) Difference (µ V) Error(%) ChannelX + Input 199995.21 -2.10 -0.00 Channel X + Input 20001.90 -0.02 -0.00 ChannelX - Input -19998.43 2.67 -0.01 ChannelY + Input 199997.45 0.04 0.00 ChannelY + Input 20000.13 -1 .84 -0.01 ChannelY - Input -20002 .53 -1.31 0.01 Channell + Input 199998.07 0.90 0.00 Channell + Input 20000.07 -1.82 -O.Q1 Channell - Input -20002.88 -1.51 0.01 Low Range Reading (µV) Difference (µ V) Error(%) ChannelX + Input 2002.15 0.71 0.04 ChannelX + Input 201 .89 0.17 0.09 ChannelX - Input -198.28 -0.11 0.06 ChannelY + Input 2000.77 -0.64 -0 .03 ChannelY + Input 201 .50 -0.14 -0 .07 ChannelY - Input -198.61 -0.36 0.18 Channell + Input 2001.31 -0.10 -0 .01 Channell + Input 200.36 -1.18 -0.59 Channell - Input -199.37 -1.01 0.51 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measurina time : 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (µV) Average Reading (µV) ChannelX 200 4.32 2.70 - 200 -2.19 -4.37 ChannelY 200 11.36 11.41 - 200 -12 .35 -1 2.96 Channell 200 -13.98 -14.32 - 200 13.11 12.07 3. Channel separation DASY measurement parameters: Auto Zero T ime: 3 sec; Measurina time: 3 sec Input Voltage (mV) Channel X (µ V) Channel Y (µ V) Channell (µV) ChannelX 200 - -0.68 -5.41 ChannelY 200 7.71 - 0.61 Channell 200 10.01 5.69 - Certificate No: DAE4-918_Jun1 8 Page 4 of 5

4. AD-Converter Values with inputs shorted DASY measurement paramet ers: Auo t Zero T 1me: 3 sec; Measunng 1me: 3 sec High Range (LSB) Low Range (LSB) ChannelX 15930 14966 ChannelY 16009 15983 ChannelZ 16005 17407 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MQ Average (µV) Std. Deviation min. Offset (µV) max. Offset (µ V) (µV) ChannelX -0.01 -2.00 1.96 0.70 ChannelY 1.43 0.40 2.68 0.39 ChannelZ -0.70 -1.89 0.85 0.46 6. Input Offset Current Nominal Input circuitry offset current on all channels : <25fA 7. I npu t Res1s . tance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) ChannelX 200 200 ChannelY 200 200 ChannelZ 200 200 8. Low 8 attery Al arm V0 Itage (Typical values for information) Typical values Alarm Level (VDC) Supply(+ Vee) +7.9 Supply (- Vee) -7.6 9. Power Consumpt1on (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply(+ Vee) +0.01 +6 +14 Supply (- Vee) -0.01 -8 -9 Certificate No: DAE4-918_Jun18 Page 5 of 5

Calibration Laboratory of Schmid & Partner s C Schweizerischer Kalibrierdienst Service suisse d'etalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recogn ition of calibration certificates Client Sporton Certificate No: DAE4-778_May18 CALIBRATION CERTIFICATE Object DAE4 - SD 000 D04 BM - SN: 778 Calibration procedure(s) QA CAL-06.v29 Calibration procedure for the data acquisition electronics (DAE) Calibration date: May 25, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards Cal Date (Certificate No.) Scheduled Calibration Keithley Multimeter Type 2001 I SN: 0810278 31-Aug-17 (No:21092) Aug-18 Secondary Standards ID # Check Date (in house) Scheduled Check Auto DAE Calibration Unit SE UWS 053 AA 1001 04-Jan-18 (in house check) In house check: Jan-19 Calibrator Box V2.1 SE UMS 006 AA 1002 04-Jan-18 (in house check) In house check: Jan-19 Name Function Signature Calibrated by: Dominique Steffen Laboratory Technician ~ 2 -. Approved by: Sven Kuhn Deputy Manager \ ,I , ~ l)}JLif 1 Issued: May 25, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE4-778_May18 Page 1 of 5

Calibration Laboratory of S Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d'etalonnage C Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland s Swiss Calibration Service Accredited by the Swiss Accreditation SeNice (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for t he recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters • DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. • Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required . • The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. • DC Voltage Measurement Linearity: Verification of the Linearity at + 10% and -10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. • Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. • Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. • AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage • Input Offset Measurement Output voltage and statistical results over a large number of zero voltage measurements. • Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. • Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto-zeroing and during measurement. • Low Battery Alarm Voltage: Typical value for information . Below this voltage, a battery alarm signal is generated. • Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4-778_May18 Page 2 of 5

DC Voltage Measurement AID - Converter Resolution nominal High Range: 1LSB; 6.1µV, full range; -100 ... +300 mV LowRange: 1LS8; 61nV, fullrange; -1 .......+3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X y z High Range 404.721 ± 0.02% (k;2) 403.519 ± 0.02% (k;2) 405.076 ± 0.02% (k;2) Low Range 3.98715 ± 1.50% (k;2) 3.96471 ± 1.50% (k;2) 4.00070 ± 1.50% (k;2) Connector Angle Connector Angle to be used in DASY system 269.0 °±1 ° Certificate No: DAE4-778_May18 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltaae Linearitv High Range Reading (µV) Difference (µ V) Error(%) ChannelX + Input 199995.64 0.22 0.00 ChannelX + Input 20002.64 0.86 0.00 ChannelX - Input -19997.90 3.08 -0.02 Channel Y + Input 199995.52 0.45 0.00 Channel Y + Input 20001.45 -0.24 -0.00 ChannelY - Input -19999.33 1.69 -0.01 Channel Z + Input 199995.39 0.09 0.00 Channel Z + Input 19999.28 -2.37 -0.01 Channel Z - Input -20004.97 -3.83 0.02 Low Range Reading (µV) Difference (µV) Error(%) Channel X + Input 2001.37 0.09 0.00 Channel X + Input 201.71 0.03 0.02 ChannelX - Input -198.71 -0.55 0.28 Channel Y + Input 2002.06 0.78 0.04 ChannelY + Input 201.56 -0.13 -0.07 Channel Y - Input -198.85 -0.61 0.31 ChannelZ + Input 2001.83 0.60 0.03 ChannelZ + Input 200.63 -1.14 -0.57 ChannelZ - Input -199.30 -0.95 0.48 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measurina time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (µV) Average Reading (µV) Channel X 200 -4.34 -5.51 - 200 6.01 4.80 Channel Y 200 0.02 -1.10 - 200 0.55 0.11 ChannelZ 200 -13.81 -14.40 -200 12.18 11.59 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measurinn time: 3 sec Input Voltage (mV) Channel X (µV) Channel Y (µV) Channel Z (µV) ChannelX 200 - -0.84 -2.53 ChannelY 200 8.46 - 0.02 ChannelZ 200 4.29 6.73 - Certificate No: DAE4-778_May18 Page 4 of 5

4. AD-Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measurino time: 3 sec High Range (LSB) Low Range (LSB) ChannelX 16056 16906 Channel Y 16191 17602 Channel Z 16433 15344 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec lnout 10MQ Std. Deviation Average (µVJ min. Offset (µVJ max. Offset (µVJ (11Vl ChannelX -0.05 -1.10 1.05 0.43 ChannelY 0.23 -1.15 1.67 0.53 Channel Z -0.76 -1.76 0.94 0.52 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. In out Resistance /Tvpical values for information) Zeroing (kOhm) Measuring (MOhm) ChannelX 200 200 Channel Y 200 200 Channel Z 200 200 8. Low Batterv Alarm Voltaae (Tvpical values for information\ Typical values Alarm Level (VDC) Supply(+ Vee) +7.9 Supply (- Vee) -7.6 9. Power Consumotion (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply(+ Vee) +0.01 +6 +14 Supply (- Vee) -0.01 -8 -9 Certificate No: DAE4-778_May18 Page 5 of 5

~ ® In CoQaboration with !!!.TTL s p e a g ~ CALIBRATION lABORATOR'f Add: No.5 1 Xueyuan Road, Haidian District, Beijing, I 00 191 , China Tel: +86-10-62304633-2512 Fax: +86-10-6230463 3-2504 E-mail : cttl@chinattl.com Http://www.chinattl.cn Client : Sporton Certificate No: 218-60383 CALIBRATION CERTIFICATE Object DAE4 - SN: 1326 Calibration Procedure(s) FF-211-002-01 Calibration Procedure for the Data Acquisition Electronics (DAEx) Calibration date: September 18, 2018 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(SI). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22±3)°C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID# Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Process Calibrator 753 1971018 20-Jun-18 (CTTL, No.J18X05034) June-19 Name Function Calibrated by: Yu Zongying SAR Test Engineer Reviewed by: Lin Hao SAR Test Engineer Approved by: Qi Dianyuan SAR Project Leader ' Issued: September 20, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: ZIS-60383 Page I of 3

~ ® lnCollaboration with - TTL s p e a g ~ CALIBRATION lABORATOll'f Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191 , China Tel: +86-10-62304633-2512 Fax: +86-10-62304633-2504 E-mail: cttl@ chinattl.com Http://www.chinattl.cn Glossary: DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters: • DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. • Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. • The report provide only calibration results for DAE, it does not contain other performance test results. Certificate No : Z 18-60383 Page 2 of 3

~ ® In Collaboration with f!!l.TTL s p e a g ~ CALIBRATION LABORATORY' Add: No.5 1 Xueyuan Road, Haidian District, Beijing, 100 191, China Tel: +86-10-62304633-2512 Fax: +86-10-62304633-2504 E-mail: cttl@chinattl.com Http://www.chinattl.cn DC Voltage Measurement AID - Converter Resolution nominal High Range: 1LSB = 6.1µV , full range= -100 ... +300 mV Low Range: 1LSB= 61nV , full range= -1 ....... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X y z High Range 404.892 ± 0.15% (k=2) 405.233 ± 0.15% (k=2) 404.616 ± 0.15% (k=2) Low Range 3.98868 ± 0.7% (k=2) 3.99146 ± 0.7% (k=2) 3.99194 ± 0.7% (k=2) Connector Angle Connector Angle to be used in DASY system 68° ± 1 ° Certificate No: Z 18-60383 Page 3 of 3


Document Created: 2019-02-15 00:48:21
Document Modified: 2019-02-15 00:48:21
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC