User Manual 1

FCC ID: HBWNLS1

Users Manual

Download: PDF
FCCID_1190554

® Model NLS1 & NLS2 Wireless Portable Intercom - Extreme Range Overview The Intercom has up to a 1000' range and allows Channel Select Button: Press multiple simultaneous conversations, using a the Channel Select button to set ACTIV HOLD OFF VOLU ME 900 MHz secure digital radio link. The intercoms form intercom to one of four secure E MONIT TALK OR an exclusive network and respond only to other channels or the paging channel. 1 2 3 4 CHAN NEL intercoms in the network. The default channel for the intercom is the paging channel Carton Inventory where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use. When batteries HOLD OFF VOLUME ACTIVE MONITOR Rubber Pads are low intercom will emit two 4 2 3 MONIT 1 OR TALK ME ACTIV VOLU E OFF HOLD TALK 1 3 CHANNEL (2 in Model NLS2) beeps every ten minutes. 2 4 An AC Adapter (not provided) can also be used to power the Intercom (2 in Model NLS2) OPTIONAL intercom. In this case, both the power and channel lights will remain on. Operation & Features Conference Mode: Conference Mode allows multiple intercoms to participate in a conversation compared to Normal Mode in which only two intercoms Active Light can communicate. All intercoms must be set to Channel Talk Channel Lights Button the same channel or the paging channel to be 1 Speaker 2 Select Button in Conference Mode. To put intercom in Conference Mode set Dipswitch #2 to UP position. 2 1 TALK 4 3 ACTI Monitor VE VOLU OF HOLDF Volume Monitor Mode: Monitor Mode is Button MONIT ME OR DOWN Button used to monitor the noise in a HOLD OFF Volume specific room. Place the intercom ACTIV E VOLU ME MONIT in the room that is to be monitored TALK OR UP Button 1 CHAN and press the Monitor button until 3 NEL 2 Dipswitch #1 4 AC Adapter Learn Button Dipswitch #2 a tone is heard. While in monitor mode the Active light will blink if On/Off: To turn intercom ON, press Talk button. To no sound is heard and will be solid if sounds are turn intercom OFF, hold down the Volume DOWN heard. Any other networked intercom can listen to button for 3 seconds. that room. If a specific channel is selected for Monitor Mode then only other intercoms on that channel or on Talk Button: To talk, hold down the paging channel can listen. Press the Monitor the Talk button. All intercoms in HOLD OFF button again to exit Monitor Mode. A tone will be VOLU the network that are on the same ACTIV TALK E ME MONIT OR heard indicating Monitor Mode is no longer active. channel will receive the signal. 1 2 3 CHAN NEL Release the Talk button when 4 Voice Activation Mode (VOX): Voice Activation done talking and within 10-15 Mode (VOX) allows a call to be answered without seconds press and hold the Talk pressing the Talk button. Once a call is heard on an button of a different intercom to make a secure intercom which has been set to VOX, a response can channel between the two. Once the channel is made be given by speaking loudly into the intercom. There the other intercoms in the network cannot hear the will be a slight delay when VOX is first activated by a conversation. voice, but will continue to transmit audio until the speaking stops. To put intercom into VOX, Volume: Pressing the Volume DOWN button will place Dipswitch #1 to the UP position. While lower the volume and pressing the Volume UP button in VOX mode, a call may be initiated by 1 2 will increase the volume. The lowest volume setting pressing the TALK button. will mute the intercom. 1

Assemble Intercom INTERCOM LEARN MODE Step 1 Press the Learn button HOLD OFF VOLUME OR until a beep is heard. MONITOR ACTIVE TALK CHANNEL 1 3 2 4 Press and hold both buttons for 5 seconds. Each intercom will emit a tone when programmed into network. Repeat for any additional intercoms. Add to an Existing Network Install 4 AA Alkaline batteries (not provided). 2 1 TALK 4 3 ACTI VE VOLU OF ME HOLDF MONIT Step 2 OR Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put any networked intercom into Learn Mode (refer to table below). INTERCOM LEARN MODE Press the Learn button OR until a beep is heard. Adhere rubber pads to bottom. HOLD OFF ACTIVE VOLUME MONITOR Repeat Steps 1 and 2 for any additional intercoms. TALK CHANNEL 1 3 2 4 Press and hold both buttons for 5 seconds. Programming Intercom Each intercom will emit a tone when programmed into The intercom must be programmed to at least one network. Repeat for any additional intercoms. other intercom to become a network or it can be programmed into an existing network. NOTE: Do not program new intercoms to each other before adding them to the network or they will form a Create New Network separate network and the memory will need to be cleared. 2 1 TALK 4 3 ACTI VE VOLU OF ME HOLDF MONIT OR HOLD OFF VOLU ME ACTIV E MONI TALK TOR 1 3 CHAN NEL 2 4 Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put the second intercom into Learn Mode (refer to the following Press and release the Talk button to verify network is table). complete. 2

Troubleshooting Intercom does not function. Need to clear intercom’s memory. Check batteries in intercom. If using an AC Adapter Press and hold Learn button, an initial beep will be ensure that it is plugged in. heard. Continue to hold until a second beep is heard Ensure intercom is connected to a network. (about 15 seconds). Ensure other intercoms are not See Programming Intercom. activated during this time. Intercoms in the network that Ensure that intercoms are on the same channel. See are on will signal during the clearing process. Once Operation & Features. memory is clear the intercom can be programmed to a new network. Intercom is not getting expected transmission range. Intercom is sending audio while no buttons are Keep antenna vertical. Keep intercom away from pressed. metal objects and electrical wiring. Cell phones, The sending intercom is set to Monitoring Mode or Voice cordless phones, or other radio devices may also Activation Mode and will activate when sound is heard. limit range. It can be taken out of Monitoring Mode by pressing the Talk button. It can be taken out of Voice Activation Mode Intercom beeps every ten minutes. by setting Dipswitch #1 to DOWN position. The battery is low in the intercom. Replace with AA See Operation & Features. Alkaline batteries or operate it with AC Adapter (not provided). A 12 volt, 300mA AC Adapter may be used NOTE: Manufacturer is not responsible for any radio or (center positive polarity on the round plug). TV interference caused by unauthorized modifications to Static and feedback is heard in intercom. this equipment. Changes or modifications not expressly The intercoms are too close to each other. A cordless approved by the manufacturer could void the authority to phone, cell phone, or other radio devices can also operate the equipment. cause static. 3

One Year Limited Warranty The Chamberlain Group, Inc. warrants to the first retail purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase. FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 www.chamberlain-DIY.com NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. © 2009, The Chamberlain Group Inc. 114A4095 All Rights Reserved


Document Created: 2009-10-19 10:10:28
Document Modified: 2009-10-19 10:10:28
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC