User Manual rev.pdf

FCC ID: H8NTCG220

Users Manual

Download: PDF
FCCID_2813418

Residential VoIP Cable Modem Quick Start Guide Chapter 1: Introduction TCG220‐Tdp is a Full Band Capture Front End Cable Voice and Wireless Gateway which has an 802.11 b/g/n access point that gives you wireless connection to the Internet with 2 Giga Ethernet ports which further expand the Local Area Network (LAN) capabilities. If you have subscribed to phone services from your cable operator then you will be able to place normal phone calls using your analogue phone and/or fax machine. TCG220‐Tdp provides one RJ‐11 connector for your phone or home phone system. TCG220‐Tdp will give you broadband Internet access, telephone connection and wireless networking all in one unit. Besides that, this residential cable gateway offers Firewall for additional protection and security and VPN (virtual private network). Package Contents Package Contents x1 TCG220‐Tdp WiFi EMTA x1 Ethernet Cable x1 Power Adaptor x1 QIG x1 Warranty card x1

Chapter 2: Overview Front Panel The following illustration shows the front panel of the EMTA: Power Indicates the Power status. DS Indicates the status of Data reception by the cable modem from the Network (Downstream Traffic) US Indicates the status of Data transmission by the cable modem to the Network (Upstream Traffic) Online Displays the status of your cable connection. The light is off when no cable connection is detected and fully lit when the modem has established a connection with the network and data can be transferred Ethernet Indicates the state of Ethernet ports WIFI Indicates the traffic on the wireless network WPS Indicates the status of the WPS functionality TEL Indicates the status of the telephone Phone 1

There will be 9 LEDs on PKE1320SW‐D112(US‐Tdp‐RoHS) / TCG220‐TdP, but DS and US are bi‐color LED. Looking at LED from top to bottom: Power, DS(bi‐color), US(bi‐color), Online, Ethernet 1,2, WiFi , WPS, TEL. DS DS1 US US1 Power (green (blue (green (blue Online Eth1 Eth2 Wifi WPS TEL color) color) color) color) Power Up ON X X X X X X X X X X Indicate Power On or OFF If during this process, the FW isn't in the Firmware CPE or there is a FW error and the CPE Flash X X X X X X X X X X fail isn't going to be able to boot, one of the led will blinking. Connect When CPE device (PC) is connect to ON X X X X X ON X X X X LAN1 LAN1 LAN1 ON X X X X X Flash X X X X When there is traffic, Eth1 LED will flash. traffic Connect When CPE device (PC) is connect to ON X X X X X X ON X X X LAN2 LAN2 LAN2 ON X X X X X X Flash X X X When there is traffic, Eth2 LED will flash. traffic CM boot From Power on to system initial ON Flash OFF Flash OFF Flash X X X X OFF cycle complete ON Flash OFF OFF OFF OFF X X X X OFF During DS scanning and acquiring SYNC ON ON OFF OFF OFF OFF X X X X OFF Complete synchronization of primary DS Register as DS bonding mode(2ch or ON ON ON OFF OFF OFF X X X X OFF more) After primary DS locked, process of ON ON ON Flash OFF OFF X X X X OFF ranging DOCSIS operation ON ON ON ON OFF OFF X X X X OFF Ranging complete Register as US bonding mode(2ch or ON ON ON ON ON OFF X X X X OFF more) After US ranging complete, process of ON ON ON ON ON Flash X X X X OFF communication between DOCSIS provision server ON ON ON ON ON ON X X X X OFF CM online(Operational) MTA ON ON X ON X ON X X X X Flash MTA provision operation ON ON X ON X ON X X X X ON MTA online(Operation) Flash ON Flash X Flash X X X X X X X During SW upgrade upgrade When performing factory reset, the Factory device shall feedback to the user by a Flash Flash X Flash X Flash X X X X X reset 2Hz blinking for during the perform of the factory reset WiFi When WiFi is enabled, the WiFi LED will X X X X X X X X ON X X enable ON. WiFi When WiFi is disabled, the WiFi LED will X X X X X X X X OFF X X disable OFF. WiFi When there is traffic, the WiFi LED will X X X X X X X X Flash X X traffic Flash. When there is a long press (>5seconds), WPS X X X X X X X X X Flash X the WPS process will initiate and the Running WPS LED will start to Flash. WPS idle X X X X X X X X X OFF X 2

Rear Panel Connector Description Slot Description 12VDC 12V DC‐IN Power connector CABLE F‐Connector RESET Reset/Reboot this Cable modem ETHERNET 1 2 Ethernet 10/100/1000 BaseT RJ‐45 connector TEL Telephony RJ‐11 connector 3

Side Panel for WPS WPS – Indicates the status of the WPS (Wi‐Fi Protected SetupTM) functionality. There is one WPS button on the Top Side Panel of TCG220‐Tdp and is designed to have multiple function. This button can be used to: Securely and Simply Get WiFi Client Connected: WPS button can be used to pairing WiFi client which also supports WPS function. A long press (press more than 5 seconds) on the WPS button will enable TCG220‐Tdp scan for any available WPS device. Note: You must ensure that the WiFi client device supports WPS function in order to use this WPS function on TCG220‐TdP. 4

3. Connecting the Residential VoIP cable modem to Your Computer Installation Procedure for Ethernet Interface Follow the steps below for proper installation: 1. Connect one end of the coaxial cable to the CABLE connection on the wall, and the other end to the CABLE jack on the TCG220‐Tdp. Note: To speed up the registration process of cable modem, the coaxial cable should be connected to the modem before the modem turned ON 2. Connect the plug from the power supply into the POWER jack on the TCG220‐Tdp, and plug the power supply into an AC outlet. Note: Use only the power supply that accompanied this unit. Using other adapters may damage the unit. 3. Connect one end of the Ethernet cable to the Ethernet port of your computer, and the other end to the ETHERNET port on the TCG220‐Tdp. 4. The TCG220‐Tdp will look for the proper cable modem signal in the Cable Television network and process the initial registration. The voice gateway is ready for data transfer after the LED “Cable Link” is lit solid green. Note: The REBOOT button at the rear panel is for maintenance purposes only. You don’t need to use it. Fig. How to set up your connection 5

CAUTION for UL North American Cable Installer: This reminder is provided to call your attention to Article 820.93 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. This symbol on your set guarantees that your product complies with the European Directives 1999/5/EC and 2009/125/EC on Safety, Telecom, Electromagnetic Compatibility and Energy using Products. 6

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐ Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non‐US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. 7


Document Created: 2015-11-13 18:25:47
Document Modified: 2015-11-13 18:25:47
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC