8

FCC ID: H38WR-101R

Users Manual

Download: PDF
FCCID_46677

EXHIBIT C User Manual

INSTRUCTION MANUAL =——————— INSTRUCTION MANUAL 3. Power Supply Connection Use DC power supply could switch with 5. Indicator. \ adaptor supply or batter of 12—18V DC. Connection DC supply , DC plug conne— a. Power ON Indicator: ction with "DC—IN" socket. (See FIG.3) This red light glows when the another plug terminal connection with DC supply and power Switch battery or power supply ON. It indicates that the rece— iver is on. b. Reception Indicator: This indicator does light during standby. When microphone signal is received, The green indicator FIG.5 light to indicate the reception of microphone. c. Audio peak Indicator: This red light fiickers when the audio signal from the microphone approaches the overload clipping level. It is affected by the transmitter gain control setting and the loudnes: of your voice. 4. Powar Switch / Volume Control Rotate this knob control power ON IOFF anc increase or decrease the valume of the receiver output. Th— is control does ot affect the AUD— 6. Squelch Control i0 PEAK indicator. This control is factory present, SQ noisy controlled adjustment, Before you turn—on the transmitter, Please turn—on the receiver at first. The receiver already have been jamming by outside (SQ JUST} signal. Please adjust SQ control until the jamming signal has disappeared. (clock—wise) FIG.4

NOTE EPTEUR : INSTRUCTION MANUAL — THE MRELESS RECRIVER LOCATED AT GOOD CONDITION PLACE. 1. install Antenna Receivers signals from the transm— itter. Make sure the antenna is fu— lly extended vertically BE CAREFUL, DON‘T DROP OFF THE MICROPHONE TO FLOOR 2.Audio Output Connector You can connect an unbalanced audio cable with a 1/4 inch phone plug between this connector and your mixer or amplifier input. KEEP AWAY RAINING OR SUN SHINE.

NAMES OF PARTS IF YOU ARE NOT TECHNICAL ENGINEER PLS. DO NOT MODIFIED OR KNOCK — DOWN IT. 1. Power ON Indicator 2. Microphone ON Indicator. 3. Audio Peak Indicator. 4. Power Switch / Volume Control. 5. Telescapic Antenna. 6. Audio Output Connector. 7. Power Input Connect.

Character : « VHF High band frequency by quartz locked controlled. Range from 174—216MHZ + Compact, lightweight, single channel receiver. * LED Indicator (Power , RF , Peak ) and telescopic antenna + Compression / Expanded circuit for extended dynamic range. * Special circuit design to delete microphone switch ON/OFF noise. Specifications : Receiving method Non—diversity receiver Carrier frequency range VHF Hi—Band 174—216MHZ Frequency stability 0.005% (25°C | Modulation mode FM (F3E) Max. deviation t 40KHz,, with limiting compress TH.D. <1% Dynamic . >100dB ~SIN Ratio_ >900B Frequencyresponse 50Hz—15KHz + 30B R)ecéfing-me-77777 Quarlz control fixed frequency Squelch |Noise control Normal=—85dBm ( Receiver sensitivity ) —65dBm ~—90dBm Adjust Audio output level Unbalance ,300mV , 10KQ load At deviation =+ 40KHz Output connector Unbalance 6.3 mm phone jack Power supply DC 12V ~ 18V 300mA With AC/DC adaptor 115/230V 50/60Hz Dimensions 152 X 98 X 36 mm Weight _ | 226g _

CONTENTS CHARAGTER —————————————— O h B o N —A —A SPECIFICATIONS ————————————— NAMES OF PARTS ———————————— INSTALLATION <—————————_—_—___— POWER SUPPLY CONNECTION INDICATOR AND SQUELCH CONTROL ——— NOTE Thank you for your kind using our wireless microphone with receiver. Before using the machine please read the instruction manual very carefully. According to our instruction manual for ensure you using of the best function and performance. If any defect please contact with our agent or dealer. It is our pleasure to serve you. Thank you for your cooperation

_~~NOILONHLSNI WNTLSASSSTNIIYTIM


Document Created: 2001-06-12 13:17:47
Document Modified: 2001-06-12 13:17:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC