SAR TEST REPORT 2

FCC ID: GUOTH03M

RF Exposure Info

Download: PDF
FCCID_1680562

Calibration Laboratory of «9 Schmid & Partner s\/7 Schwelzerischer Kallbrierdienst Service suisse c‘étatonnage Engineering AG Servio svizzero ditaratura Zeughausstrasse $3, 8004 Zurich, Switzeriand Swiss Calioration Service Accredited by h Swiss Accredtation Serice (SAS) Accreditation No: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multlateral Agreament forthe recognition of callbration cortiicates crent (ATE(Auden) Gertiicate No: D2450V2—712.Feb12 |CALIBRATION CERTIFICATE Object D2450V2 — SN: 712 Caltration procedure(s) QA CAL—05.v8 Calibration procedure for dipole validation kitsabove 700 MHz. Calbration date: February 28, 2012 "This calbration ceniicate documents the traceabilty to national standards, which realze he physical uns of measurements (S1) ‘Tre measurements and the uncortainies with confidence probabilly are gven on the folowing pages and are part ofthe coricate. Allcaltations have been conducted in the closed laboratoryfaciiy: envronment temporature(22 x 3)°C and humidty < 70%. Calbration Equipment used (MATE cricalfocaltration) Primary Standards n« Gal Date (Gonticate No Scheted Caltbraton Power moter EPM—442 esrasoros 0s—Oct11 (No. 217.0r451) cotie Power sensor HP 8481A usareszres os.0st11 (No. 217—01a51) coti2 Reference 20 8 Attenvator sn sons (204) 20ar11 (No. 217—01000) Apere Type—N mismalch combinaton SN: 8047.2/08827 204Mar11 (No.217—01971) Apere Reference Probe ES3DV3 sh azos 30—0ee—11 (No. ESS@205_Dect1) Dec—te oaee Shi eor Oé—Ju—I1 (No. DAEA—601_ult1) Juere Secondary Standards n« Check Date (n house) Scheduled Chock Power sensor HP 8481A mvatoseoir 18—0ct02 (in house check Oct—11) in house chock: Oct—18 AF generator RSS SMT—06 100005 04—Aug—98 i house check Oct—11) in house chock: Oct—18 Natwork Analyzor HP 8750E ussrasoses S4208 18.0ct01 (nhousecheck Oct11) in house chockc Oct12 Name runction Signature Caltrated by: israe Ek Nacuq Tabsratoy Technician I J (/é/_ Approved by: Kale Pobove Techrical Managor /& g: Issued: Febrvary 23, 2012 "This calbration ceniicate shallnot breproduced excopt in ful wihout writen approvalof he laboratony Certficate No: D2450V2—712_Feb12 Page 1 of 8

Calibration Laboratory of Schwelzerischer Kallbrierdienst Schmid & Partner Service sulsse c‘étatonnage Engineering AG Serviclo sviezero ditarature Zoughausstrasse 43, 8004 Zurich, Switzeriand Swiss Caltoration Service Accredited by the Swiss Accredtation Srvice (SAS) Accreditation No.: SCS 108 The Swies Accreditation Service is one of the signatories to the EA Multilateral Agreement for trecognition of calbration cortiates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy.z NA not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2008, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, December 2003 b IEC 62208—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)*, February 2005 c Federal Communications Commission Office of Engineering & Technology (FCC OET), "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposureto Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Furtherdetails are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. Cortficate No: D2450V2—712_Feb12 Page 2 of 8

@l Measurement Conditions DASY system contiquration, as far as not given on page1. DASY Version nasys vseso Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHiz# 1 MHz Head TSL parameters ‘The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 220°C so2 1.80 mhoim Measured Head TSL parameters 220 :02) °C 38.0 26 % 1.88 mho/m + 6 % Head TSL temperature change during test <05°C SAR result with Head TSL SAR averaged over 1 om° (1 g) of Head TSL Condition SAR measured 250 mW input power 136 mW /g SAR for nominal Head TSL parameters normalized to 1W 50.5 mW ig # 17.0 % (k=2) SAR averaged over 10 em" (10 g) of Head TSL condition SAR measured 250 mW input power 6.26 mW / g SAR for nominal Head TSL parameters normalized to 1W 24.8 mW /g = 16.5 % (k=2) Body TSL parameters Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0°C s27 1.95 mhoim Measured Body TSL parameters g20=02)°C 52816 % 2.02 mhoim +6 % Body TSL temperature change during test <05°C — «— SAR result with Body TSL SAR averaged over 1 om* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.7 mW / g SAR for nominal Body TSL parameters normalized to 1W 49.9 mW / g a 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 5.05 mW / g SAR for nominal Body TSL parameters normalized to 1W 28.6 mW / g # 16.5 % (k=2) Cortficate No: D24S0V2—712_Feb12 Page 3 of 8

Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point s5.0 0 + 25 n Retum Loss —25.5 B Antenna Parameters with Body TSL Impedance, transformed to feed point 51.7 0 + 4.9 in Return Loss —25.8 dB General Antenna Parameters and Design [ Electrical Delay (one irection} | 1.144 ns After long term use with 100W radiated power, only a sight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—ircuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the ‘Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is stil according to the Standard. No excessive fore must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on July 05, 2002 Cortficate No: D2450V2—712_Feb12 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 23.02.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 712 Communication System: CW; Frequency: 2450 MHz . Medium parameters used: {= 2450 MHz; 0 = 1.86 mho/m; &;= 38.9; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASYS (IEEE/TEC/ANSI C63.19—2007) DASY532 Configuration: + Probe: ES3DV3 — SN3205; ConvF(4.45, 4.45, 4.45); Calibrated: 30.12.201 1 * Sensor—Surface: 3mm (Mechanical Surface Detection) * Electronics: DAE4 $n601; Calibrated: 04.07.201 1 * Phantom: Flat Phantom 5.0 (front); Type: QDOOOPSOAA; Serial: 1001 * DASY52 52.8.0(692); SEMCAD X 14.6.4(4989) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, d Reference Value = 100.1 V/m; Power Dri Peak SAR (extrapolated) = 28.3820 SAR(I g) = 13.6 mW/g; SAR(1O g) = 6.26 mW/g Maximum value of SAR (measured) = 17.534 mW/g nae asse zuse zooo 0 dB = 17.530mW/g = 24.88 dB mW/g Cortficate No: D2450V2—712_Fob12 Page 5 of 8

@l Impedance Measurement Plot for Head TSL 2s reo zor2. oeresise 1 u rs asasese messso asmes ph 2 450.000 000 nz ty 149 ma Sramr 2 mis Stte 2 esa.coo a00 mis Cortficate No: D2450V2—712_Feb12 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 23.02.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 712 Communication System: CW; Frequency: 2450 MHz Medium parameters used: = 2450 MHz; a = 2.02 mho/m; s, = 52.3; = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY52 Configuration: * Probe: ES3DV3 — SN3205; ConvF(4.26, 4.26, 4.26); Calibrated: 30.12.201 1 * Sensor—Surface: 3mm (Mechanical Surface Detection) * Electronies: DAEB4 Sn601; Calibrated: 04.07.201 1 * Phantom: Flat Phantom 5.0 (back); Type: QDOOOP5OAA; Serial: 1002 * DASY52 52.8.0(692); SEMCAD X 14.6.4(4989) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, d h Reference Value = 94094 V/m; Power Drift = 0.0032 dB Peak SAR (extrapolated) = 26.0450 SAR(I g) = 12.7 mWi/g; SAR(1O g) = 5.95 mW/g Maximumvalue of SAR (measured) = 16.700 mW/g o [ss zuse 0 dB = 16.700mW/g = 24.45 dB mW/g Contficate No: D2450V2—712_Feb12 Page 7 of 8

jatl Impedance Measurement Plot for Body TSL 2s res zore oorserze ERD sn a uks asusesa astzne ariie pi 2 4s0.000 c00 hiz ver ty 159 ma cue its ime Stak1 2 250.000 ooo miz se z Certficate No: D24SOV2—712_Fob12 Page 8 of 8

Calibration Laboratory of g Schweizerischer Kalibrierdienst Schmid & Partner g Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse43, 8004 Zurich, Switzerland S Swiss Callbration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multiateral Agreement for the recognition of calibration cortificates client Sporton—TW (Auden) Cortificate No: ES3—3270_Sep11 CALIBRATION CERTIFICATE Object ES3DV3 — SN:3270 Callbration procedure(s) QA CAL—01.v8, QA CAL—23.v4, QA CAL—25.4 Calibration procedure for dosimetric E—field probes Calibration date: September 12, 2011 This callbration certficate documents the traceabilty to national standards, which realizethe physical units of measurements (S1) The measuremnts and the uncertainties with confidence probabilly are given on the following pages and are part of the cortiicate. All ealibrations nave been conducted in the closed laboratory facilty: environment temparature (22 + 3)°C and humidity < 70% Calibration Equipment used (M&TE criical for calibration) Primary Standards io Cal Date (Certficate No.) Scheduled Calbration Power meter E44198 Gestzosera 3t—Mar—11 (No. 217—01372) Aper2 Power sensor E4412A mvar40so87 3t—Mar—11 (No. 217—01372) Aprt2 Reference 3 dB Attenuator SN: 85054 (3c) 20—Mar—11 (No. 217—01369) Aprd2 Reference 20 d8 Attenuator SN: 20—Mar—11 (No. 217—01367) Aprt2 Reference 30 dB Attenuator St 20—Mar—11 (No. 217—01370) Aprr2 Reference Prove ES3DV2 s 29—Dec—10 (No. ES3—3013.Dect0) Dec—11 oag4 s 3—May—11 (No. DAE4—654_May11) May—12 Secondary Standards io Check Date (in house) Scheduled Check RF generator HP 8648C Ussed2u01700 4—Mug—99 (in house check Oct—09) in house checkOct—11 Network Analyzer HP 8753E US37300585 18—Oct—01 (in house check Oct—10) in house check: Oct—11 Name Function Signature Calibrated by: Jeton Kastrat Laboratory Technician o Approved by: Katla Pokovic Technical Manager /%g_ issued: September 12, 2011 This callbration certficate shall not be reproduced except in full without written approval of the laboratory. Certficate No: ES3—3270_Sep11 Page 1 of 11 varre en ruwe on avvime sonpe nepun rvumuer. revn wiu rugy

Calibration Laboratory of G Schweizerischer Kalibrierdienst Schmid & Partner . Sorvice suisse d‘étalonnage Engineering AG «5 Sorvizio svizzero dtaratura Zeughausstrasse 43, 8004 Zurich, Switzerland /.fi\\ Swiss Galibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMxy,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B, C modulation dependentlinearization parameters Polarization q ©» rotation around probe axis Polarization 8 8 rotation around an axis thatis in the plane normal to probe axis (at measurement center), fe., 8 = 0 is normal to probe axis Calibration is Performed According to the Following Standards: a) —IEEE Std 1528—2003, ‘IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, December 2003 b) IEC 62209—1, "Procedureto measurethe Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)®, February 2005 Methods Applied and Interpretation of Parameters: & NORMxy,z: Assessed for E—field polarization 3 = 0 (f s 900 MHz in TEM—cell; £> 1800 MHz: R22 waveguide). NORMxy,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not affect the E*—field uncertainty inside TSL (see below ConvF). * NORM(Axy,z = NORMx.y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of thefrequency response is included in the stated uncertainty of ConvF. * DCPxy,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. * PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on thesignal characteristics * Asyz Bxy,z: Cay,z, VRxy,z: A, B, C are numericallinearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. * ConvF and Boundary Effect Parameters: Assessed in fiat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for { > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConVF is used in DASY version 4.4 and higher which allows extendingthevalidity from + 50 MHz to + 100 MHz. * Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. * Sensor Offset: The sensor offset corresponds to the offset of vitual measurement center from the probe tip (on probe axis). No tolerance required. Certificate No: ES3—3270_Sep11 Page 2 of 11 nvre m roue cervueniy srorp. nepon rvamuer. rewor wiu ruge s >

@l ESSDV3 — SN:3270 September 12, 2011 Probe ES3DV3 SN:3270 Manufactured: February 25, 2010 Calibrated: September 12, 2011 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: E83—3270_Sep11 Page 3 of 11 seure n rgor cav revimiy vanp. nepor ivumuer. revorero

ES3DV3— SN:3270 September 12, 2011 DASY/EASY — Parameters of Probe: ES3DV3 — SN:3270 Basic Calibration Parameters Sensor X Sensor Y Sensor 2 Unc (k=2) Norm (uVi(Vim)")" 111 1.20 122 £10.1% DCP (mV)" 2 100.4 98.9 101.1 Modulation Calibration Parameters uiD Communication System Name PAR A B ¢ VR Unc® 4B 48 48 mV (k=2) 10000 Cw a.00 x c.00 0.00 100| 1029 127% y |_c.00 0.00 100| 1116 2 000 0.00 100 1065 The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of NormX,YZ do not affect the E*—field uncertainlyinside TL (see Pages 5 and 6). * Numerical inearization parameter: uncertainty not required. © Uncertaintyis determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: ES3—3270_Sep11 Page 4 of 11 revprrce evarenoue. »uge ren sroald

@l ESSDV3— SN:3270 September 12, 2011 DASY/EASY — Parameters of Probe: ES3DV3 — SN:3270 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity Depth Unct. f(MHz)*_|_ Pormittivity® (Sim)" ConvFX ConvFY ConvFZ Alpha (mm) (k=2) 835 41.5 0.90 6.04 6.04 6.04 0.80 1.00 £120% 900 41.5 0.97 5.95 5.95 5.95 0.80 1.00 £120% 1750 40.1 1.37 5.32 5.32 5.32 0.80 124 £120% 1900 40.0 1.40 5.14 5.14 5.14 0.80 125 £120% 2000 40.0 1.40 5.12 5.12 5.12 0.80 1.24 £120% 2450 30.2 1.80 4.52 4.52 4.52 0.80 138| +120% © Frequency validty of £ 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the Convuncertainty at callbration frequency and the uncertainty for the indicated frequency band. " At frequencies below 3 GHiz, the validity of tissue parameters (c and a) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validty of ssue parameters (s and o) is restricted to + 5%. The uncertainty is the RSS of the Convr uncertainty for indicated target tssue parameters. Crtificate No: ES3—3270_Sep11 Page 5 of 11 narre nrrvue can rverimg sip nopon rvumuer. rewor wiu nugy~

@l ES3DV3— SN:3270 September 12, 2011 DASY/EASY — Parameters of Probe: ES3DV3— SN:3270 Calibration Parameter Determinedin Body Tissue Simulating Media Relative Conductivity Depth Unct. f(MHz)*_|_Permittivity® (Sim)" ConvFX ConvFY| ConvFZ Alpha |__(mm) (k=2) 835 55.2 o.97 6.16 6.16 6.16 0.80 1.00 £12.0 % 900 55.0 1.05 6.07 6.07 6.07 0.80 1.00 £12.0 % 1750 53.4 1.49 4.87 4.87 4.87 0.80 131 £12.0 % 1900 53.3 1.52 4.64 4.64 4.64 0.80 131 £12.0 % 2000 58.3 1.52 4.71 4.71 4.71 0.80. 1.31 £12.0 % 2450 52.7 1.95 4.28 4.28 4.28 0.80. 1.00 £12.0 % © Frequency valdity of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restrcted to +. 50 Miz. The uncertainty is the RSS of the Conv uncertainty at calibration frequency and the uncertainty for the incicated frequency band. Atfrequencies below 3 GHiz, the validity of tssue parameters (s and a) can be relaxed to + 10% ifliquid compensation formula is applied to measured SAR values. Al frequencies above 3 GHz, the validity of issue parameters (s and a) is restricted to 5%. The uncertainty is the RSS of the GonvF uncertainty for indicated target tissue parameters. Certificate No: £$3—3270_Sep11 Page 6 of 11 narre nrrvue can rverimg sip nopon rvumuer. rewor wiu nugy~

QI ES3DV3— SN:3270 September 12, 2011 Frequency Response of E—Field (TEM—Cell:fi110 EXX, Waveguide: R22) Frequency response (normalized) "®l TEMm Raz Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certficate No: ES3—3270_Sep11 Page 7 of 11 se v n es rvwe ce evse wecpe »ropore varmione revir uy »uge rve aroaed

’(@y ES3DV3— SN:3270 September 12, 2011 Receiving Pattern (¢), 9 = 0° £=600 MHz,TEM £=1800 MHz,R22 * a * * * * * * * [e] Tot x v 2 Tot x v 2 Rol[] |UfiIHZ 60%7 WSfiHl Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: ES3—3270_Sep11 Page 8 of 11 wivre m igor cav reuriy vp. mepurcrvumuer. revor o 1o

’@l ES3DV3— SN:3270 September 12, 2011 Dynamic Range f(SARneaq) (TEM cell , f = 900 MHz) 10° 105 10¢ 3 & § ® 10° ® 5 & 102 10‘ 10° 10 107 10‘ 19 10‘ 10° SAR {mW/om$] Le] aJ Le X compensated X not compensated Y compensated + e (+ Y not compensated Z compensated Z not compensated 2 m 17 a 2 & o § —r u4 2 y t r * 108 102 101 108 101 SAR [mW/cmd] Le] & Le] X compensated X not compensated Y compensated L+] Ce] ea Y¥ not compensated Z compensated Z not compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: £83—3270_Sep11 Page 9 of 11 s re m iwer caw rourimy srurp nepor rvumiuer. revor w

@l ES3DV3— SN:3270 September 12, 2011 Conversion Factor Assessment £= 835 MHz.WGLS RQ (H_convr) 1= 1900 MHz,WGLS R22 (H_conyr) 3 { 10| ; Sints m * —<= t 4 slisnsfssssessdelaielesd sfop.edeieipriepie ies § i E. > «$ «1 Bs al «ie «l wl G) Deviation from Isotropy in Liquid Error (¢, 8), f = 900 MHz —10 —08 —06 .04 02 00 02 04 06 08 10 Uncertainty of Spherical Isotropy Assessment: * 2.6% (k=2) Certificate No: ES3—3270_Sep11 Page 10 of 11 viyre m reot cav revemn. nepurcivumuer. revor io _o—

@I ES3DV3— SN:3270 September 12, 2011 DASY/EASY — Parameters of Probe: ES3DV3 — SN:3270 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) Not applicable Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 10 mm Tip Diameter 4 mm Probe Tip to Sensor X Calibration Point 2 mm Probe Tip to Sensor Y Calibration Point 2 mm Probe Tip to Sensor Z Calibration Point 2 mm Recommended Measurement Distancefrom Surface 3 mm Certificate No: ES3—3270_Sep1 1 Page 11 of 11 nrre m rer on rvurm siwip. nepun rumuer. revus uio nugy >

jatl Calibration Laboratory of _ Schweizerischer Kalibriordienst Schmid & Partner g Service suisse aéialonnage Engineering AG Serviclo svizzero di taratura Zeughausstrasse 49, 8004 Zurich, Swtzerland S swiss Caltoration Service Accredited by the Sviss Accroditation Sorvice (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of tsignatories to the EA Mulllateral Agreament for the recognition of cabration certiicates @nttratendae: oorpppaprrrgrrcmmeucy "This caltration cerficate documents the raceabiltyto national standards, which realizethe physical unts of measuremonts (S1. "The measurements and the uncertants with confdence probabilty are given on the folowing pages and are pat l the corticat. Allcaltrations have bean conductad in the clased laboratory faciit: envronment tomporature (22 + 3)°C and huridiy « 70%. Galtration Equipment used (MATE erticalfor caltration) Primary Standards 10# Cal Date (Gortfcate No) Scheduld Caltbration Kolihoy Mutimater Type 2001 sh oarcere 28—Sep—10 (No:toare) Sepir Secondary Standards EB Gheck Date (n house) Scheduld Check Calibator Box V1.1 5E UMS 008 AB 1008 O#«Jun—11 (in house check) in house cheoks Jun—t2 Caltrated by: Approved by: Issuedt Juty 21, 2011 "This calbration coriicate shall not be reproduced excent in ful wihout witen approval ofthelaboratory. Certficate No: DAE4—541_Jul11 Page 1 of 5

Calibration Laboratory of Schweizerischer Kallbrierdionst Schmid & Partner Service sulsse d‘étalonnage Engineering AG Servizio svizzero ditaratura Zeughausstrasse 43, 8004 Zurich, Suitzeriand Swiss Calloration Service Accredited by the Sniss Accreditation Service (GSAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories tothe EA Multlateral Agroementfor the recognition of callration certicates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters * DC Voltage Measurement: Calibration Factorassessed for use in DASY system by comparison with a calibrated instrument traceable to nationalstandards. The figure given corresponds to thefull scale range of the voltmeter in the respectiverange. * Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technicalinformation as a result from the performance test and require no uncertainty. * DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. * Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. * Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. * AD ConverterValues with inputs shorted: Values on the internal AD converter corresponding to zero input voltage * Input Offset Measurement Output voltage and statistical results over a large number of zero voltage measurements. * Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. * Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. «_ Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signalis generated. * Power consumption: Typical value for information. Supply currents in various operating modes. Cortficate No: DAE4—541_Jul11 Page 2 of 5

QI DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1ss= 6ctuV . full range= —100...+800 mV Low Range: 18 stnv , full range= —1 amV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 se Calibration Factors x v z High Range 404.582 + 0.1% (k=2) 404.450 + 0.1% (k=2) 404.224 £0.1%(k=2) Low Range 3.96870 + 0.7% (k=2) 893611 4 0.7% (k=2) |_3.97524 £0.7%(k=2) Connector Angle Connector Angle to be used in DASY system 200.5%41° Cortiicate No: DAE4—541_Jult1 Page 3 of5

@I Appendix 1. DC Voltage Linearity High Range Reading (uV) Difference (uV) Error (%) Channel X + Input 200008.1 088 0.00 Channel X + Input 20002.50 3.10 oc2 Channel X — Input 1989827 453 002 Channel Y + nput 1988988 155 0.00 Channel Y _ _+ Input 19887.00 230 001 Channel Y — Input 19898.95 165 001 Channel 2 _ _+ input 188000.8 160 0.00 Channel 2 _ _+ Input 20001.15 1.75 o.01 Channel 2 —Input —19898.20 321 002 Low Range Reading (uV) Difference (u¥) Error (%) Channel X + input 20005 ose o03 Channel X + input 200.06 104 oce Channel X____— Input 20023 023 on Channel Y + Input 20002 025 0.01 Channel Y input 180.49 ast 25 Channel Y — Input 20076 076 o.8 Channel Z _ _+ Input 2000.0 007 0.00 Channel Z + Input 19895 095 047 Channel Z _ _— Input —200.06 076 0.38 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 seo Common mode High Range Low Range Input Voltage (mV) Average Reading (V) Average Reading (u¥) Channel X 200 1221 10.47 +200 a92 1003 Channel ¥ 200 1.33 131 —200 320 256 Channel 2 200 132 on —200 457 225 3. Channel separation DASY measurement paramaters: Auto Zero Time: 3 see; Measuring time: 3 sec input Voltage (mV) Channe! X (uV) Channel Y (xV) ChannelZ (uV) GChannel X 200 + 277 —0.01 Channel Y 200 1.35 + 4.90 Channel Z 200 002 0.12 5 Certficate No: DAEA—541_Jult1 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 seo High Range (LSB) Low Range (LSB) Channel X 16012 16048 Channel Y 15780 1se79 Channel 2 1078 16504 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 seo Input 10M Average (1V) min. Offset (u¥) max. Offset (uv) * :’:";;'““ Channel X 014 —1.05 0.50 o27 Channel Y 069 235 or8 086 Channel 2 084 32 020 o23 6. Input Offset Current Nominal Input cirouitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (Ohm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel 2 200 200 8. Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vee) +79 Supply (— Veo) 76 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Veo) +001 +6 14 Supply (— Vee) —o.01 a a Cerificate No: DAE4—541_Jult 1 Page 5 of 5


Document Created: 2012-04-13 15:27:01
Document Modified: 2012-04-13 15:27:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC