Test Report

FCC ID: GPO2002019

Test Report

Download: PDF
FCCID_4243565

TEST REPORT Report No.: E20190308772201-3 Application No.: E20190308772201 Applicant: GEMMY INDUSTRIES (HK)LIMITED BVI Address: No.301 on 3rd Floor, East Ocean Centre,No.98 Granville Road,Kowloon,Hong Kong Sample Wireless Remote Controller Description: Model: 2002019 Adding Model: / FCC ID: GPO2002019 Test Specification: FCC 47 CFR Part 15 Subpart C Test Date: 2019-03-27 to 2019-04-01 Issue Date: 2019-04-15 Test Result: PASS Prepared By: Reviewed By: Approved By: Darry Wu / Test Engineer Eve Wang /Technical Manager Tony Han / Manager Date:2019-04-15 Date:2019-04-15 Date:2019-04-15 Other Aspects: / Abbreviations: ok / P = passed; fail / F = failed; n.a. / N = not applicable The test result in this test report refers exclusively to the presented test sample. This report shall not be reproduced except in full, without the written approval of GRGT. Address: No.1301 Guanguang Road Xinlan Community, Guanlan Street, Longhua District Shenzhen, 518110, GRG METROLOGY & TEST (SHENZHEN) CO., LTD People’s Republic of China Tel:+86-755-61180008 Email: szgrgt@grgtest.com http://www.grgtest.com Identifying code:651290

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 DIRECTIONS OF TEST 1. This company carries out test task according to the national regulation of verifications which can be traced to National Primary Standards and BIPM. 2. The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. 3. If there is any objection concerning the test, the client should inform the laboratory within 15 days from the date of receiving the test report. Page 1 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 TABLE OF CONTENTS 1. TEST RESULT SUMMARY ............................................................................................................................ 4 2. GENERAL DESCRIPTION OF EUT.............................................................................................................. 5 2.1 APPLICANT ................................................................................................................................................... 5 2.2 MANUFACTURER ........................................................................................................................................ 5 2.3 FACTORY ...................................................................................................................................................... 5 2.4 BASIC DESCRIPTION OF EQUIPMENT UNDER TEST ........................................................................... 5 2.5 TEST OPERATION MODE ........................................................................................................................... 6 8.1. LOCAL SUPPORTIVE.............................................................................................................................. 6 3. LABORATORY AND ACCREDITATIONS .................................................................................................. 7 3.1 LABORATORY.............................................................................................................................................. 7 3.2 ACCREDITATIONS ...................................................................................................................................... 7 3.3 MEASUREMENT UNCERTAINTY ............................................................................................................. 7 4. LIST OF USED TEST EQUIPMENT AT GRGT........................................................................................... 8 5. ANTENNA REQUIREMENT .......................................................................................................................... 9 6. RADIATED SPURIOUS EMISSIONS .......................................................................................................... 10 6.1. LIMITS ..................................................................................................................................................... 10 6.2. TEST PROCEDURES ............................................................................................................................. 10 6.3. TEST SETUP ........................................................................................................................................... 14 6.4. DATA SAMPLE ...................................................................................................................................... 15 6.5. TEST RESULTS ...................................................................................................................................... 16 7. 20DB BANDWIDTH........................................................................................................................................ 24 1.1. LIMITS ..................................................................................................................................................... 24 1.2. TEST PROCEDURES.............................................................................................................................. 24 1.3. TEST SETUP ........................................................................................................................................... 24 1.4. TEST RESULTS ...................................................................................................................................... 24 8. DUTY CYCLE ................................................................................................................................................. 27 2.1. LIMITS ..................................................................................................................................................... 27 2.2. TEST PROCEDURES.............................................................................................................................. 27 2.3. TEST SETUP ........................................................................................................................................... 27 2.4. TEST RESULTS ...................................................................................................................................... 27 9. RESTRICTED BANDS OF OPERATION .................................................................................................... 28 9.1. LIMITS ..................................................................................................................................................... 28 9.2. TEST PROCEDURES.............................................................................................................................. 28 9.3. TEST SETUP ........................................................................................................................................... 29 9.4. TEST RESULTS ...................................................................................................................................... 30 APPENDIX A: PHOTOGRAPH OF THE TEST ARRANGEMENT.................................................................. 34 Page 2 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 1. TEST RESULT SUMMARY FCC Part 15.249 Standard Item Limit / Severity Result Antenna Requirement §15.203 PASS Conducted Emissions §15.207 (a) N/A1) Radiated Spurious §15.249(d) PASS Emission FCC Part 15,Subpart C (15.249) 20 dB Bandwidth N/A PASS Duty Cycle N/A PASS Restricted bands of §15.205 operation PASS Note 1): The EUT received DC 3V supply by the cell. Page 3 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 2. GENERAL DESCRIPTION OF EUT 2.1 APPLICANT Name: GEMMY INDUSTRIES (HK)LIMITED BVI Address: No.301 on 3rd Floor, East Ocean Centre, No.98 Granville Road, Kowloon, Hong Kong 2.2 MANUFACTURER Name: GEMMY INDUSTRIES (HK)LIMITED BVI Address: No.301 on 3rd Floor, East Ocean Centre, No.98 Granville Road, Kowloon, Hong Kong 2.3 FACTORY Factory 1 Name : ZAIXING ELECTRONIC (SHENZHEN)CO., LTD. Address : 3#, 1st Road Yang Yong, Shapu Community, Songgang, Baoan District, Shenzhen City, Guangdong Province, China. Factory 2 Name : DynaTech Co. Ltd Address : 259-261 Xincheng Road, Qiaotou Town, Dongguan, Guangdong, China Factory 3 Name : YUAN HONG CO., LTD Address : No. 3, meichun A industrial zone, meichun fang, fumei city, Ba Ria Vung Tau Province, Vietnam. 2.4 BASIC DESCRIPTION OF EQUIPMENT UNDER TEST Equipment: Wireless Remote Controller Model No.: 2002019 Adding Model / Trade Name: / Power supply DC 3V supply by the cell Frequency 2407MHz~2477MHz Range Transmit Peak: 83.88dBuV/m (Max.) Power: Average: 58.75dBuV/m (Max.) Antenna Monopole antenna with 0dBi gain(Max) Specification: Modulation GFSK type: Temperature -20°C ~ +70°C Range: Hardware 115604-USA (V1) Page 4 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 Version: Software 115604-USA (V1) Version: Note: / 2.5 TEST OPERATION MODE Test Item Mode No. Description of the modes Conducted Emission / / Radiated Emission 1 Continuously Transmitting 8.1. LOCAL SUPPORTIVE Name of Equipment Manufacturer Model Serial Number Note / / / / / Cable / / / / / Test software: Software version Test level / 3 Page 5 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 3. LABORATORY AND ACCREDITATIONS 3.1 LABORATORY The tests and measurements refer to this report were performed by EMC Laboratory of GRG METROLOGY & TEST (SHENZHEN) CO., LTD Add. : No.1301 Guanguang Road Xinlan Community, Guanlan Street, Longhua District Shenzhen, 518110, People’s Republic of China Telephone : +86-755-61180008 Fax : / 3.2 ACCREDITATIONS A2LA Certificate Number 2861.01 3.3 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Measurement Frequency Uncertainty 30MHz～1000MHz 4.8dB Horizontal 1GHz～26.5GHz 5.8dB Radiated Emission 30MHz～1000MHz 4.8dB Vertical 1GHz～26.5GHz 5.9dB This uncertainty represents an expanded uncertainty factor of k=2. Page 6 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 4. LIST OF USED TEST EQUIPMENT AT GRGT Serial Calibration Name of Equipment Manufacturer Model Number Due Radiated Spurious Emission& Restricted bands of operation ESPI Test Receiver ROHDE&SCHWARZ ESPI 101026 2020-01-09 EXA signal analyzer Agilent N9010A MY52221469 2020-01-10 Bilog Antenna Schwarzbeck VULB 9160 9160-3401 2019-12-21 Horn Antenna Schwarzbeck BBHA9120 D286 2019-12-21 Active Loop Antenna COM-POWER AL-130 121044 2019-12-27 EM Electronics Amplifier EM330 060661 2019-12-21 Corporation High Noise Amplifier Agilent 8449B 3008A02060 2019-12-21 Hygrothermograph VICTOR HTC-1 NA 2019-12-24 Test SW FARAD EZ-EMC/ CCS-3A1-CE 20 dB Bandwidth EXA signal analyzer Agilent N9010A MY52221469 2020-01-10 Duty cycle EXA signal analyzer Agilent N9010A MY52221469 2020-01-10 Page 7 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 5. ANTENNA REQUIREMENT The EUT has only one antenna. The antenna is monopole antenna. The max gain of antenna is 0 dBi. Which accordance 15.203.is considered sufficient to comply with the provisions of this section Page 8 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 6. RADIATED SPURIOUS EMISSIONS 6.1. LIMITS Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Fundamental Field Strength of Fundamental Field Strength of Harmonics Frequency Field Strength (mV/m) (μV/m) 902-928 MHz 50 500 2400 - 2483.5 MHz 50 500 5725 - 5875 MHz 50 500 24.0 - 24.25 GHz 250 2500 Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency (MHz) Field Strength (μV/m) Measurement Distance (m) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 6.2. TEST PROCEDURES (please refer to measurement standard) 1) Sequence of testing 9 kHz to 30 MHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used. --- If the EUT is a floor standing device, it is placed on the ground. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions. --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 3 meter. --- The EUT was set into operation. Page 9 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 Pre measurement: --- The turntable rotates from 0°to 315°using 45°steps. --- The antenna height is 0.8 meter. --- At each turntable position the analyzer sweeps with peak detection to find the maximum of all emissions Final measurement: --- Identified emissions during the pre measurement the software maximizes by rotating the turntable position (0°to 360°) and by rotating the elevation axes (0°to 360°). --- The final measurement will be done in the position (turntable and elevation) causing the highest emissions with QPK detector. --- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the pre measurement and the limit will be stored. 2) Sequence of testing 30 MHz to 1 GHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane. --- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 3 meter. --- The EUT was set into operation. Pre measurement: --- The turntable rotates from 0°to 315°using 45°steps. --- The antenna is polarized vertical and horizontal. --- The antenna height changes from 1 to 3 meter. --- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to find the maximum of all emissions. Page 10 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 Final measurement: --- The final measurement will be performed with minimum the six highest peaks. --- According to the maximum antenna and turntable positions of premeasurement the software maximize the peaks by changing turntable position (±45°) and antenna movement between 1 and 4 meter. --- The final measurement will be done with QP detector with an EMI receiver. --- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement with marked maximum final measurements and the limit will be stored. 3) Sequence of testing 1 GHz to 18 GHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used. --- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 3 meter. --- The EUT was set into operation. Pre measurement: --- The turntable rotates from 0°to 315°using 45°steps. --- The antenna is polarized vertical and horizontal. --- The antenna height scan range is 1 meter to 2.5 meter. --- At each turntable position and antenna polarization the analyzer sweeps with peak detection to find the maximum of all emissions. Page 11 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 Final measurement: --- The final measurement will be performed with minimum the six highest peaks. --- According to the maximum antenna and turntable positions of premeasurement the software maximize the peaks by changing turntable position (±45°) and antenna movement between 1 and 4 meter. This procedure is repeated for both antenna polarizations. --- The final measurement will be done in the position (turntable, EUT-table and antenna polarization) causing the highest emissions with Peak and Average detector. --- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position, antenna polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the pre measurement with marked maximum final measurements and the limit will be stored. 4) Sequence of testing above 18 GHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used. --- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 1 meter. --- The EUT was set into operation. Pre measurement: --- The antenna is moved spherical over the EUT in different polarisations of the antenna. Final measurement: --- The final measurement will be performed at the position and antenna orientation for all detected emissions that were found during the premeasurements with Peak and Average detector. --- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored. NOTE: The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 3MHz for RMS Average (Duty cycle < 98%) for Average detection (AV) at frequency above 1GHz, then the measurement results was added to a correction factor (10 log(1/duty cycle)). Page 12 of 33

Report No.: E20190308772201—3 Application No.: E20190308772201 reei : Grozoaroto 6.3. TEST SETUP Turntable . 3m \ EUT Test im Receiver 0.8 m Ground Plane Comial Cable Figure 1. 9KHz to 30MHz radiated emissions test contiguration Antenna Tower Search eur Anterna X / RF Ts Receiver C Tum Table Ground Plane J Figure 2. 30MHz to IGHs radiated emissions test configuration Arenna 4 tower Horn anterns Spectrum analyzer Turmable Preamp [{CJ ow oto Figure3. Above IGHe radiated emissions test configuration mss rorn

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 6.4. DATA SAMPLE 30MHz to 1GHz No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBuV/m) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) xxx xxx 37.06 -15.48 21.58 40.00 -18.42 QP Vertical Above 1 GHz No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBuV/m) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) xxx xxx 65.45 -11.12 54.33 74.00 -19.67 peak Vertical xxx xxx 63.00 -11.12 51.88 54.00 -2.12 AVG Vertical Frequency (MHz) = Emission frequency in MHz Ant.Pol. (H/V) = Antenna polarization Reading (dBuV) = Uncorrected Analyzer / Receiver reading Correction Factor (dB/m) = Antenna factor + Cable loss – Amplifier gain Result (dBuV/m) = Reading (dBuV) + Correction Factor (dB/m) Limit (dBuV/m) = Limit stated in standard Margin (dB) = Remark Result (dBuV/m) – Limit (dBuV/m) Peak = Peak Reading QP = Quasi-peak Reading AVG = Average Reading Page 14 of 33

Report No.: E20 190308772201—3 Applicatior No.: E20 190308772201 FCCiD: GrO2002019 6.5. TEST RESULTS . 30MHz to 1GHz: Pre—scan all channel and recorded the worst case results in this report. Mode: TX High channel (2477MH2) Date: Date: 2019—03—27 80.0_dBu¥/m Limiti: — Morgin: — an _ 1 n an.oud 127.00 2eaoo aer.o0 ata.oo Si5.00 1200 roo.00 ns 00 T000.00 iz No. |_Frequency _|_Reading Correct Resut Limi Margin Remark Fore C (dBu¥im) FactoriaB/m) (dBu¥im) (dBu¥im) CS 1 ss.s000 3745 —1s.85 15.50 4000 2140 or Vertical 2 79.4700 3.16 2047 18.50 4000 2131 or Vertical 3 195.s700 2085 —15.02 1183 4350 3167 or Verical 4 |_4so.0100 27.19 —l1.16 16.03 4500 2007 or Vertical s s20.s200 25.07 —10.5s 1839 4500 —27.51 or Verical & |_sas.z00 26.13 s47 2056 4500 253 or Vertical ras sorns

Report No.: E2019030877220 1—3 Application No.: 52019030877220 1 FCCID : GPO2002019 Mode: TX High channel (2477MHz) Date: Date: 2019—03—27 80.0_dBu¥/m Limiti: — Morgin: — 4n_,—| n an.ouo rero 2za00 sei0 ale00 Sis00 e12.00 70900 ooo 00 1000.00 iz No: |_Frequency _|_Reading Corect Resurt Timk Margin Remark Fore in dBu¥im) Factor(dBm (aBu¥im) (dBuVim) B 1 186.1700 2ose —17.58 1225 4350 3124 or Horizontal > Sse.7300 3645 "s85 2751 40.00 1839 or Horizonta 3 571.1700 2225 305 .19 4000 2481 oP Horizontal a 71zss00 350 50 270 4000 1500 or Horizonta 5 s70.720 2718 463 255 4000 2345 or Horizontal s 938.5000 26098 407 2291 4000 2300 or Horizontal Remarks 1. No ernission found between lowest intermal used/generated frequency to 30MHz. 4 Rediated emissions measnred in frequency range from OkHz to 1GHz were made with an instrument using peak/lquasi—peak detector mode. 3. Quasi—peak test would be performed if the peak result were greater than the quasi—peak Timit or as required by the applicant. 4. Measurements abore show onlup to 6 maximum emissions noted, or would be lesser, with " N/A " remaik, if no specific emissions from the EUT are recorded (ie: margin> 204B from the applieable limit)and considered that‘s already beyond the background noise floor. m ieorss

Report No.: E20190308772201—3 Application No.: E20190308772201 FCC ID : GPO2002019 Above 1GHz: Mode: TX Lowest channel (2407MHz) Date: 2019—03—29 110.0 dBuVim Limit] —— Limit2 — 1 20 20.0 2474,000 2474.60 2475 .20 2475.00 2476.40 2477.00 2477 60 2478.20 2478.00 2480.00 MHz No. Frequency Reading Correct Result Timit Margin Remark Pole (MHz) (dBuV/m) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 1 2406.798 85.32 —1.44 83.88 114.00 —30.12 poak Vertical 2 2406.798 60.19 —1.44 58.75 94.00 —35.25 AVG Vertical Mode: TX Lowest channel (2407MHz) Date: 2019—03—29 110.0 dBuVim Limit] —— Limit2 — 1 20 20.0 2403.000 2404.40 2405.00 2405.60 2406.20 2406 .00 2407 .40 2408.00 2408.60 240900 MHz No. Frequency Reading Correct Result Timit Margin Remark Pole (MHz) (dBuV/m) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 1 2406.842 7322 —1.44 71.78 114.00 1222 poak Horizontal 2 2406.842 48.09 —1.44 46.65 94.00 17.35 AVG Horizontal Remark: AVG result=Peak result—duty eycle Page l7or33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 Mode: TX Low channel (2407 MHz) Date: 2019-03-28 No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBuV/m) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 1 1189.000 47.03 -6.16 40.87 74.00 -33.13 peak Vertical 2 2827.000 44.18 0.16 44.34 74.00 -29.66 peak Vertical 3 3736.000 43.01 1.24 44.25 74.00 -29.75 peak Vertical 4 4816.000 46.75 2.35 49.10 74.00 -24.90 peak Vertical 5 7165.000 41.35 7.46 48.81 74.00 -25.19 peak Vertical 6 7948.000 41.13 9.10 50.23 74.00 -23.77 peak Vertical 7 1891.000 45.23 -3.00 42.23 74.00 -31.77 peak Horizontal 8 3349.000 43.31 0.92 44.23 74.00 -29.77 peak Horizontal 9 4816.000 49.95 2.35 52.30 74.00 -21.70 peak Horizontal 10 4816.000 47.56 2.35 49.91 54.00 -4.09 AVG Horizontal 11 6832.000 41.23 6.71 47.94 74.00 -26.06 peak Horizontal 12 7957.000 40.48 9.11 49.59 74.00 -24.41 peak Horizontal 13 9550.000 41.21 10.36 51.57 74.00 -22.43 peak Horizontal Page 18 of 33

Report No.: E20 190308772201 —3 Application No.: E2019030877220 1 FCCID : GPO2002019 Mode: TX Middle channel (2445MHz) Date: 2019—03—29 110.0_ dBu¥/m Limitt: Limite: zo 30.0 2442000244260 2a4320 2asa.o0 Ratadb 2a45.00 244560 244620 2446.00 2440.00 MHz No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBuV/Am) Factor(dB/m) (dBu¥/n) (dBu¥/m) (dB) 1 2444.814 83.34 —1.36 81.98 114.00 —32.02 peak Vertical 2 2444.814 58.21 —1.36 56.85 94.00 —37.15 AVG Vertical Mode: TX Middle channel (2445MHz) Date: 2019—03—29 110.0_ dBuw/m zo 1 20.0 »442.0002442.60 2aa320 2ads60 raiddo 2445.00 244560 2445.20 2446.00 2448.00 MrHz No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBuV/Am) Factor(dB/m) (dBu¥/n) (dBu¥/m) (dB) 1 2444.820 71.38 —1.36 70.02 114.00 43.98 peak Horizontal 2 2444.820 46.25 —1.36 44.89 94.00 49.11 AVG Horizontal Remark: AVG result=Peak result—duty cycle Page 19 or 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 Mode: TX Mid channel (2445 MHz) Date: 2019-03-28 No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBuV/m) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 1 2242.000 45.70 -1.81 43.89 74.00 -30.11 peak Vertical 2 3079.000 43.30 0.91 44.21 74.00 -29.79 peak Vertical 3 4429.000 42.21 2.41 44.62 74.00 -29.38 peak Vertical 4 4888.000 45.59 2.30 47.89 74.00 -26.11 peak Vertical 5 6517.000 40.82 6.04 46.86 74.00 -27.14 peak Vertical 6 8632.000 41.64 9.01 50.65 74.00 -23.35 peak Vertical 7 1918.000 45.68 -2.84 42.84 74.00 -31.16 peak Horizontal 8 3214.000 45.24 0.92 46.16 74.00 -27.84 peak Horizontal 9 4888.000 48.46 2.30 50.76 74.00 -23.24 peak Horizontal 10 5644.000 41.27 4.13 45.40 74.00 -28.60 peak Horizontal 11 7282.000 40.83 7.74 48.57 74.00 -25.43 peak Horizontal 12 7975.000 41.06 9.15 50.21 74.00 -23.79 peak Horizontal Page 20 of 33

Report No.: E20190308772201—3 Application No.: E20190308772201 FCCID : GPO2002019 Mode: TX Highest channel (2477MHz) Date: 2019—03—29 110.0_dBuvim Limitt — Limit2 — 1 70 20.0 2474.000 2474.60 2475 20 2475.00 2476 40 2477.00 2a77.60 2470.20 2470.00 2400.00 MHz No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBu¥im) Factor(dB/m) (dBu¥/m) (dBu¥/im) (aB) 1 2476.982 83.04 —1.30 81.74 114.00 —32.26 peak Vertical 2 2476.982 57.91 —1.30 56.61 94.00 —37.39 AVG Vertical Mode: TX Highest channel (2477MHz) Date: 2019—03—29 110.0 dBuV/m Limith: — Limit? — 1 70 30.0 2ara.rsurarags nazags 2arsss Rareds 2areirs Parrias 2arnes 2arass 2479.75 MHz No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBu¥im) Factor(dB/m) (dBu¥/m) (dBu¥/im) (aB) 1 2476.828 71.88 —1.30 70.58 114.00 4342 peak Horizontal 2 2476.828 46.75 —1.30 45.45 94.00 ~48.55 AVG Horizontal Remark: AVG result=Peak result—duty cycle Page 21 or33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 Mode: TX High channel (2477 MHz) Date: 2019-03-28 No. Frequency Reading Correct Result Limit Margin Remark Pole (MHz) (dBuV/m) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 1 1153.000 47.10 -6.26 40.84 74.00 -33.16 peak Vertical 2 4132.000 42.40 1.84 44.24 74.00 -29.76 peak Vertical 3 4357.000 42.46 2.28 44.74 74.00 -29.26 peak Vertical 4 4951.000 43.63 2.26 45.89 74.00 -28.11 peak Vertical 5 6436.000 41.55 5.92 47.47 74.00 -26.53 peak Vertical 6 7894.000 41.26 8.99 50.25 74.00 -23.75 peak Vertical 7 1225.000 46.83 -6.06 40.77 74.00 -33.23 peak Horizontal 8 2512.000 45.97 -1.19 44.78 74.00 -29.22 peak Horizontal 9 4951.000 45.54 2.26 47.80 74.00 -26.20 peak Horizontal 10 6580.000 41.48 6.18 47.66 74.00 -26.34 peak Horizontal 11 6850.000 41.88 6.74 48.62 74.00 -25.38 peak Horizontal 12 7723.000 40.71 8.69 49.40 74.00 -24.60 peak Horizontal Remark: 1 Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2 Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3 Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4 Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5 Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. Page 22 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 7. 20DB BANDWIDTH 1.1. LIMITS None: for reporting purpose only. 1.2. TEST PROCEDURES 1) Remove the antenna from the EUT, and then connect a low loss RF cable from antenna port to the spectrum analyzer. 2) Set the spectrum analyzer as RBW=100 kHz, VBW=300 kHz, Span=6MHz, Sweep = auto. 3) Mark the peak frequency and 20dB (upper and lower) frequency. 4) Repeat above procedures until all frequencies measured were complete. 1.3. TEST SETUP EUT Spectrum analyzer 1.4. TEST RESULTS Frequency Bandwidth Limit Channel Test Result (MHz) (kHz) (kHz) Low 2407 1460 PASS Mid 2445 1252 >500 PASS High 2477 1202 PASS Page 23 of 33

Report No.: E20190308772201—3 Application No.: E20190308772201 FCCID : GPO2002019 Channel 2407MHz soa xC smeeroce Awcior _| orcosspiieror, 2010 Center Freq 2.406999400 GHz Genter Freq:2408308400 GHz Radio Std: None co Trig:FreeRun AvglHold> tort0 #iEGainow #atten: 10 4B Radio Device: 8TS 1Lo dBidiv Leabade —Ti Center 2407 GHz Span 6 MHz ScdcdMtyd Eddendcyo Sweep 1 ms Occupied Bandwidth Abolelanl +16.4 dBm 1.3632 MHz Transmit Freq Error BcrRSIGr OBW Power 99.00 % Ee Ecnscu EuLc Eie s —20.00 dB fise stavs Channel 2445MHz = sc < seseroce Awcior _| ceronsy amaeon2010 Center Freq 2.445000000 GHz Genter Freg: 2445000000 GHz Radio Std: None o Trig:FreeRun AvglHold> tort0 HEGain:Low #atten: 10 dB Radio Device: BTS 10 dBidiv Ref 0.00 dBm 1t bo c a Span 6 MHz #Res BW 100 kHz VBW 300 kHz Sweep 1 ms Occupied Bandwidth Lcnsc +15.6 dBm 1.1637 MHz Transmit Freq Error ~188.17 kHz oc 99.00 % x dB Bandwidth lc x dB —20.00 dB fise stavs Page 24 of 33

Report No.: E20190308772201—3 Application No.: E20190308772201 FCCID : GPO2002019 Channel 2477MHz Apilent Spectrum Analyzer — Occupied BW oie Amchor ceisai00 amaeron, 2010 Ref Value 0.00 dBm Genter Freq:2477000000 GHz Radio Std: None co Trig:Free Run AvglHold> tort0 #iEGaintow #Atten: 10 48 Radio Device: BTS Ref 0.00 dBm Center 2477 GHz Span 6 MHz #Res BW 100 kHz pdcty o Sweep 1 ms Occupied Bandwidth teol +19.3 dBm 1.1473 MHz Transmit Freq Error +214.43 kHz OBW Power 99.00 % x dB Bandwidth uic Ebls ues Jiss cros Page 25 of 33

Report No.: E20190308772201—3 Application No.: E20190308772201 FCC ID : GPO2002019 8. DUTY CYCLE 2.1. LIMITS None: for reporting purpose only. 2.2. TEST PROCEDURES 1) Removethe antenna from the EUT and then connect a low loss RF cable from the antenna port to an EMI Test Receiver. 2) Set center frequency of spectrum analyzer = operating frequency. 3) Set the spectrum analyzer as RBW, VBW=1MHz, Span = 0Hz, Adjust Sweep = 20ms 4) Only need to test one channel and record data 2.3. TEST SETUP EUT ®! Spectrum analyzer 24. TEST RESULTS 20Log {1/[on/(on+off}]}= 20Log [1/(0.504/9.1}]=25.13dB. on . s senserotee Asuicuore _| cosnoorieon 2ore [ Euc nctiti e _ Avg Type: Log.Pur se ~> Trig:FreeRun ow Aten: 10 dB LebadeTo Center 2407000000 GHz Span 0 Hz Res BW 1.0 MHz Sweep 14.00 ms (1001 pts) en wooe Te so T v runcnon roncnonwork rncronvaie Eans 504.0 us| (A 0.58 dB Page 26033

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 9. RESTRICTED BANDS OF OPERATION 9.1.LIMITS §15.205(a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.69525 960 - 1240 7.25 - 7.75 4.125 - 4.128 16.80425 - 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 16.80475 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 25.5 - 25.67 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 37.5 - 38.25 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 73 - 74.6 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 74.8 - 75.2 2200 - 2300 14.47 - 14.5 8.291 - 8.294 108 - 121.94 2310 - 2390 15.35 - 16.2 8.362 - 8.366 123 - 138 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 149.9 - 150.05 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.52475 - 3260 - 3267 23.6 - 24.0 12.29 - 12.293 156.52525 3332 - 3339 31.2 - 31.8 12.51975 - 156.7 - 156.9 3345.8 - 3358 36.43 - 36.5 12.52025 162.0125 - 167.17 3600 - 4400 12.57675 - 167.72 - 173.2 12.57725 240 - 285 13.36 - 13.41 322 - 335.4 9.2.TEST PROCEDURES 1) The EUT is placed on a turntable, which is 1.5m above the ground plane. 2) The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3) EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4) Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: a) PEAK: RBW=1MHz / VBW=1MHz / Sweep=AUTO b) AVERAGE: RBW=1MHz / VBW=1/T / Sweep=AUTO 5) Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. Page 27 of 33

Report No.: E20190308772201-3 Application No.: E20190308772201 FCC ID ： GPO2002019 9.3.TEST SETUP Antenna tower 3m Horn EUT antenna 4m Spectrum analyzer Turntable 1.5m 1m 30cm Pre-amp Page 28 of 33

Report No.: E2019030877220 1—3 Application No.: E20190308772201 FCCID : GPO2002019 9.4.TEST RESULTS Channel Low (2407MHz) Detector mode: Peak Polarity: Vertical 100.0 dBu¥im Limit: — Limie: — so I| 20.0 2210 aovzs00.00 easn.od 2aan.on Paso.00 2as0.00 2ara.00 2a00.00 2s90.00 210.00 wirte Detector mode: Average Polarity: Vertical 100.0 dBu¥im Limit: — Limie: — so 1 20.0 2210 aovzs00.00 easn.od 2aan.on Paso.00 2as0.00 2ara.00 2a00.00 2s90.00 210.00 wirte No. Frequency Reading Factor Result Limit Margin Remark Pole MHz dBuV dB dBuV/im dBuV/m dB 1 2390,000 53.20 —L48 51.72 74.00 —22.28 Poak Vertical 2 2406.800 85.10 —L.44 —— 74.00 —— Poak Vertical 1 2390,000 41.99 —L48 40.51 54.00 —1349 Average Vertical 2 2406.900 84.26 —L.44 ——— 54.00 ——— Average Vertical Page 29 or33

Report No.: E2019030877220 1—3 Application No.: E20190308772201 FCCID : GPO2002019 Channel Low(2407MHz) Detector mode: Peak Polarity: Horizontal 100.0_dBuv/m Limin Limite TTE so 20.0 2310 0002300 00— zasn.o0 2aan00 zasn.00 zdsn 00— 2are.00 2a0n.00 239000 z10.00 rte Detector mode: Average Polarity: Horizontal 100.0 dBu¥/m Limitl: — Limie: — so nant 1 20.0 »stou0023z000 2as0.00 2na000 2ss0.00 escoue 2270.00 2300.00— 2300.00 zar0.00 Mi= No. Frequency Reading Factor Result Limit Margin Remark Pole MHz dBuV dB dBuV/m dBuV/m dB 1 2390.000 54.15 —L48 52.67 74.00 —21.33 Peak Horizontal 2 2406400 7296 —L44 ——— 74.00 —— Peak Horizontal 1 2390.000 42.02 —1.48 40.54 54.00 —1346 Average Horizontal 2 2406.900 71.63 —1 44 ——— 54.00 —— Average Horizontal Page 0o33

Report No.: E2019030877220 1—3 Application No.: E2019030877220 1 FCCID : GPO2002019 Channel High(2477MHz) Detector mode: Peak Polarity: Vertical 100.0_dBuv/m Limit: — Limie: — 1 so wA ulmm 20.0 2«re aovzara oo 2aro oo 2arend 2anod 2s oo Padeno 2o 00— 2nna d 2500.00 rte Detector mode: Average Polarity: Vertical 100.0_dBuv/m Limit: — Limie: — 1 so 20.0 2«re aovzara oo 2aro oo 2arend 2anod 2s oo Padeno 2o 00— 2nna d 2500.00 rte No. Frequency Reading Factor Result Limit Margin Remark Pole MHz dBuV dB dBuV/m dBuV/m dB 1 2476.780 82.38 —L.30 —— 74.00 —— Peak Vertical 2 2483.500 57.98 —L.27 56.71 74.00 —17.29 Peak Vertical 1 2476.780 81.34 —1.30 —— 54.00 —— Average Vertical 2 2483.500 4243 —L.27 41.16 54.00 —12.84 Average Vertical Pagesi or33

Report No.: E2019030877220 1—3 Application No.: E20190308772201 FCCID : GPO2002019 Channel High(2477MHz) Detector mode: Peak Polarity: Horizontal 100.0 dBu¥/m Limin: — Limie: — 7 so Emmmaptiret Mba 20.0 »amooonzaraue raro.n0 2areno zade oo Raosoe Race.od 2t 00— 249400 2500.00 Mz Detector mode: Average Polarity: Horizontal 100.0_dBuv/m Limit: — Limie: — 1 so 20.0 2are.a00za73.00 2aroo0 2arene 2ez oo zesn 2ace.no 2e00— 2ana 00 2500.00 rie No. Frequency Reading Factor Result Limit Margin Remark Pole MHz dBuV dB dBuV/m dBuV/m dB 1 2476.900 71.74 —L.30 —— 74.00 —— Peak Horizontal 2 2483.500 54.04 —L27 52.77 74.00 —21,23 Peak Horizontal 1 2476.780 70.29 —L.30 —— 54.00 —— Average Horizontal 2 2483.500 42.30 —1.27 41.03 54.00 —12.97 Average Horizontal Remark: Max field strength in 3m distance. No any other emission which falls in restricted bands can be detected and be reported. Pagestor33

Report No.: E20190308772201—3 Application No.: E20190308772201 FCCID : GPO2002019 APPENDIX A: PHOTOGRAPH OF THE TEST ARRANGEMENT RSE (Below 1GHz) --------------------This is the last page of the report. ——————————————————————— Page 33 of 33


Document Created: 2019-04-16 16:13:04
Document Modified: 2019-04-16 16:13:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC