6

FCC ID: FI7MREF56

Test Report

Download: PDF
FCCID_64141

MeasurementReport Product..___..........00clcl2l: External Data/Fax Modem With Voice Manufacture ____________._.__: Archtek Telecom Corporation FCC ID.____... _: FUMREFS6 Model.___ _: S6M4IF Report No._..._._._._._._.: MLT9I806P 15004 Test Date.__.._._.______: JUL,15.1998 Test By Max Light Technology Co.,Ltd. Room 5, SF, No.125, Section 3 RooseveltRoad,; Taipei, Taiwan., R.0.C. Tel: 886—2—2363—2447 Fax: 886—2—2363—2597

MAX LIGHT MEASUREMENT REPORT Page: 2/19 Fable of Contents : 1. General ___ 4. TL Conducted Emissions Requirements ____________________ _______________ 9. IIL Radiated Emissions Requirements _____________________ ________________13. Appendix I (EUT Test Setup) _____________________________ ________________ 18. Report Number: MLT9806P15004 FCC ID: FIZMREFSG

MAX LIGHT MEASUREMENT REPORT Page: 3/19 CERTIFICATION We here by verify that : The test data, data evaluation, test procedures and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4—1992. All test were conducted by MLT(Max Light Technology Co.,Ltd) Room 5, SF, No.125, Section 3 Roosevelt Road, Taipei, Taiwan, R.O.CAlso, we attest to the accuracy of each. We further submit that the energy emitted by the sample EUT tested as described in the report is in compliance with Class B radiated and conducted emission limit of FCC Rules Part 15 Subpart B. EUT : External Data/Fax Modem With Voice Applicant : ArchtekTelecom Corporation . 4F. No.9, Lane 130, Min—Chyuan Rd., Hsin—Tien , Taingi ,Taiwan Manufacturer : Archtek Telecom Corporation . 4F. No.9, Lane 130, Min—Chyuan Rd., Hsin—Tien , Taipei ,Taiwan Model No : 5634IF FCC ID : FI7TMREF56 a Prepared by T qflpproved by : Roger Chen Report Number: MLT9806P15004 FCC ID: FIZMREF56

T D »ax 11onr ; . MEASUREMENT REPORT Page: 4/19 L. GENERAL 1.1 Introduction The following measurement report is submitted on behalf of Archtek Telecom Corporation. in support of a Glass B Digital Device certification in accordance with Part2 Subpart J and Part 15 Subpart A And B of the Commission‘s and Regulations. 1.2 Description of EUT EUT : External Data/Fax Modem With Voice Applicant : Archtek TéelecomCorporation . 4F. No.9, Lane 130, Min—Chyuan Rd., Hsin—Tien , Talpei, Taiwan Manufacturer : Archtek Telecom Corporation . 4F. No.9, Lane 130, Min—Chyuan Rd., Hsin—Tien , Taipei, Taiwan Model No : 56341IF FCC ID : FITMREF56 Power Type : Powered by PC Phone Cable : RJ—11Cx2(Nonshielded, 7 long ,Plastic hoods) During testing the EUT was operated at Tx or Rx mode for each emission measured. This was done in order to ensure that maximum emission levels were attained. Report Number: MLT9806P15004 FCCFIZMREF56

MAX LIGHT MEASUREMENT REPORT Page: 5/19 1.3 Description of Support Equipment in order to construct the minimum system which required by the ANSI C63.4—1991, following equipments were used as the support units. Computer : COMPAQ Model No. : 3284 Serial No. : L7O8BKTB4154 FCC ID : EJH3284 Keyboard : COMPAQ Model No. : KPQ—E99Z2C—13 Serial No. : 237743—334 FCC iD : CMYKPQ7285 Monitor : COMPAQ Model No. : 3030 Serial No. : 7TO4AG19TGO99 FCC ID : BJMCM14UH Mouse : COMPAQ Model No. : 285728—001 Serial No. : 97033491 FCC IiD : FSUGMZE4 Printer : PANASONIC Model No. : KX—P10801 Serial No. : 7CKAKE98933 FCC ID : ACJ5Z6KX—P10801 PSTN Simulator : MLT Model No. :1101 Serial No. : N/A Report Number: MLT9806P15004 FCC ID: FIZMREF56

MAX LIGHT MEASUREMENT REPORT Page: 6/19 Telephone : GE Mode! No. : 2—9240A Serial No. : 1943K Speaker : KAKA Mode! No. : 2K—A01 Serial No. : 189665 Microphone : Ever Power Model No. : TC—944 Serial No. : N/A Report Number: MLT9I806P15004 FCC ID: FIZMREFSG6

MAX LIGHT MEASUREMENT REPORT Page: T/19 1.4 cdnfiguration of System Under Test Power Supply RS—232 RS—232 RJ11C Cables [] PSTN Printer EUT Monitor Telephone PC Mic. Keyboard Speaker Mouse During testing the EUT(External Data/Fax Modem with voice) was connected to the Compaq PC. So there is no need for additional 1/O card. A mouse was connected to the mouse port and a printer was connected to the parallel port. A telephone set was connected to the Phone—Jackof. EUT and the Line Jack of EUT was connected to a simulator of PSTN. And the Speaker Jack and Microphone Jack were connected with a smalil microphone and a external speaker. Report Number: MLTI6O6P15004 FCC ID: FITZMREFSG

MAX LIGHT MEASUREMENT REPORT Page: 8/19 1.5 Test Procedure All measurements contained in this report were performed according to the techniques described in Measurement procedure ANSI €63.4—1992 "Measurement of unintentional Radiators." 1.6 General Test Condition The conditions under which the EUT operates were varied to determine their effect on the equipment‘s emission characteristics. The final configuration of the test system and the mode of operation used during these tests was chosen as that which produced the highest emission levels. However, only those conditions which the EUTwas considered likely to encounter in normal use were investigated. The system‘s radiated and conducted emissions were investigated while the computer alternately transferred data to the EUT as well as to the monitor and printer. Using a test program which sent a continuous stream of "HM" characters to monitor and transferred data to and from the EUT was proven to worst case emissions.The system‘s physical layout and cabling was randomly arranged to ensure that maximum emission levels were attained. Report Number: MLT9I806P15004 FCC ID: FIZMREF5G

MAX LIGHT MEASUREMENT REPORT Page: 9/19 TL Conducted Emissions Requirements 2.1 General & Setup : The power line conducted emission measurements were performed in a shielded enclosure. The EUT was assembled on a wooden table which is 80 centimeters high, was placed 40 centimeters from the backwali and at least 1 meter from the sidewall. Power was fed to the EUT from the public utility power gridthrough a line filter and EMCO Model 3825/2 Line Impedance Stabilization— Networks (LISN). The LISN housing, measuring instrumentation case, ground plane, etc., were electrically bondedtogether at the same RF potential. The Spectrum analyzer was connected to the AC line through an isolation transformer. The 50—o0hm output oftheLISN wasconnected to the spectrum analyzer directly. Conducted emission levels were in the CISPER quasi—peak detection mode. The analyzer‘s6 dB bandwidth was set to 9 KHz. No post—detector video filter was used. The spectrum was scanned from 450 —KHz to 30—MHz. The physical arrangement of the test system andassociated cabling was varied (within the scope of arrangements likely to be oncowntered in actual use) to determine the effect on the unit‘s emanations in amplitude and frequency. All spurious emission frequencies were observed. The highest emission amplitudes relative to the appropriate limit were measured and have been recorded in paragraph 2.6. 2.2 Test Eqyipment List: A. EMCO 3825/2 LISN (S/N:2654) B. EMCO 3825/2 (S/N:2658) C. HP 8591EM 9KHZ—1.8GHz Spectrum Analyzer (S/N:73412A00110) D. Shielded Room (MLT—SR1) Report Number: MLT9806P15004 FCC ID: FI7MREFSG6

MAX LIGHT MEASUREMENT REPORT Page: 10/19 2.3 Test Configuration: Rear View of The Test Configuration Report Number: MLT9806P15004 FCC ID: FIZMREFSG6

MAX LIGHT MEASUREMENT REPORT Page: 11/19 2.4 Test condition: EUT tested in accordance with the specifications given by the manufacturer , and exercised in the most unfavorable manner. 2.5 Conducted Emissions Limits: Frequency range (MHz) Limits (dBuV) 0.45 to 30 47.9 Report Number: MLT9806P15004 FCCID:FIZMREF5G

MAX LIGHT MEASUREMENT REPORT Page: 12/19 2.6 Measurement Data Of Conducted Emissions: The following table show a summary of the highest emissions of power line conducted emissions to the HOT and NATURAL conductor of the EUT power. Manufacturer : Archtek Telecom Corporation. Model No : 5634IF EUVT : External Data/Fax Modem With Voice Power Line Conducted Emissions (Class B) Conductor Frequency Peak Amplitude Limits (MHz) (dBuV) {dBuV) 0.45 33.58 479 0.75 32.35 47.9 9.63 42.53 47.9 L1 14.93 33.34 47.9 15.67 37.28 479 2440 37.82 479 30.00 32.58 479 0.45 33.82 479 0.75 30.16 47.9 9.63 42.44 47.9 L2 14.93 35.82 47.9 15.67 34.02 47.9 2440 38.06 419 30.00 32.42 479 Notes : 1.LT; One end & Ground L2: The other end & Ground 2.Height of table on which the EUT was placed : 0.8 m. 3.The above testresuits are obtained under the normal condition. Report Number: MLT9I806P15004 FCC ID: FIZMREF56

MAX LIGHT MEASUREMENT REPORT Page: 13/19 TL Radiated Emissions Requirements 31 General & Setup : Prior to open—field testing, the EUT was placed in a shielded enclosure and scanned at a close distance to determine its emission characteristics. The physical arrangement of the EUT was varied (within the scope of arrangements likely to be encountered in actual use) to determine the effect on the unit‘s emanations in amplitude, directivity, and frequency. The exact system configuration which produced the highest emissions was noted so it could be reproduced later during the open—field tests. This was done to ensure that the final measurements would demonstrate the worst—case interference potential of the EUT. Final radiation measurements were made on a three—meter, open—field test site. The EUT system was placed on a nonconductive turntable which is 0.8 meters height, top surface 1.0 x 1.5 meter. The spectrum was examined from 30 MHz to 1000 MHz using an Hewlett Packard 8591EM Spectrum Analyzer, EMCO Biconical Antenna (Mode! 3142) for 30—1000MHz. At each frequency, the EUT was rotated 360 degrees, and the antenna was raised and —lowered from one to four meters to find the maximum emission levels. Measurements were taken using both horizontal and vertical antenna polarization. Appropriate preamplifiers were used for improving sensitivity and precautions were taken to avoid overloading or desensitizing the spectrum analyzer. No post—detector video filters were used in the test. The spectrum analyzer‘s 6 dB bandwidth was set to 120 KHz, and the analyzer was operated in the quasi—peak detection mode. The highest emission amplitudes relative to the appropriate limit were measured and recorded in paragraph 3.6. 3.2 Test Eqyipment List: A. HP 8591EM 9KHz—1.8GHz Spectrum Analyzer (S/N:73412A00230) B. HP 8447D Pre Amplifier (S/N:2944A08954) C. EMCO 3142 Biconilog Antenna (S/N:1184) D. HP 8590A 10KHz—1.5GHz Spectrum Analyzer (S/N:5212A000211) Report Number: MLT9806P15004 FCC ID: FI7TMREF5G6

MAX LIGHT MEASUREMENT REPORT Page: 15/19 3.4 Test condition: EUT tested in accordance with the specifications given by the manufacturer , and exercised in the most unfavorable manner. 3.5 Radiated Emissions Limits: Frequency range (MHz) Peak{(dBuV) 30 to 88 40 88 to 216 43.5 216 to 960 46 Above 960 54 Report Number: MLT9806P15004 FCC ID: FIZMREFSG6

MAX LIGHT MEASUREMENT REPORT Page: 16/19 3.6 Measurement Data Of Radiated Emissions: 3.6.1 Open Field Radiated Emissions (HORIZONTAL) The highest peak values of radiated emissions from the EUT at various antenna heights, antenna polarization, EUT orientation , etc. are recorded on the following Manufacturer : Archtek Telecom Corporation Model No 5 5634IF EUT : External Data/Fax Modem With Voice Radiated Emissions (HORIZONTAL) Frequency Amplitude Ant. Table Limits(Class B) Margin (MHz) (dBuV/m) (m) |(Degree) (dBu¥/m} (dB) 56.44 34.52 1 300 40 —5.48 141.14 37.32 2.5 300 43.5 —6.18 169.36 37.45 2.5 270 43.5 —6.05 225.80 39.13 2 300 46 —6.87 254.04 41.51 2 270 46 ~4.49 310.48 40.42 2.5 360 46 —5.58 338.71 41.11 2.5 300 46 —4.89 366.93 40.38 2.5 360 46 —5.62 395.16 39.99 2 200 46 —6.01 423.38 41.48 1.5 360 46 —4.52 451.60 40.07 1.5 360 46 —5.93 Notes : 1.Margin= Amplitude — Limits 2.Distance of Measurement : 3 Meter (30—1000MHz) 3.Height of table for EVT placed: 0.8 Meter. 4ANT= Antenna height. 5.Amplitude=Reading Amplitude —Amplifier gain+Cable toss +Antenna factor (Auto calculate in spectrum analyzer) Report Number: MLT9806P15004 FCC ID: FIZMREF56

MAX LIGHT MEASUREMENT REPORT Page: 17/19 3.6.2 Open Field Radiated Emissions (VERTICAL) The highest peak values of radiated emissions from the EUT at various antenna heights, antenna polarization, EUT orientation , etc. are recorded on the following. Manufacturer : Archtek Telecom Corporation. Model No 5 5634IF EUT : External Data/Fax Modem With Voice Radiated Emissions (VERTICAL) Frequency Amplitude Ant. Table |Limits(Class B) Margin (MHz) (dBuV/m) {m) |(Degree) (dBuV¥/m) (dB) 56.44 35.45 1.5 360 40 ~4,55 141.14 38.43 1.5 300 43.5 —5.07 169.36 40.39 1 300 43.5 —3.11 225.80 39.50 1 270 46 —6.50 254.04 38.44 1 300 46 —7.56 310.48 39.51 1 300 46 —6.49 338.71 4142 1.5 360 46 —4.58 366.93 40.50 1.5 0 46 —5.50 395.16 39.42 1.5 270 46 —6.58 423.38 40.12 1 360 46 —5.88 451.60 39.50 1 360 46 —6.50 Notes : 1.Margin= Amplitude — Limits 2.Distance of Measurement : 3—Meter (30—1000MHz) 3.Height of table for EUT placed: 0.8 Meter. 4ABNTZ Antenna height. S.Amplitude= Reading Amplitude —Amplifier gain+Cable loss +Antenna factor (Auto calculate in spectrum analyzer) Report Number: MLT9806P15004 FCC ID: FIZMREFSG6

MAX LIGHT MEASUREMENT REPORT Page: 18/19 Appendix I— EUT Test SETUP M MENT WER R TAGE 0.8M LISN Metalfloor surfaced with 30mm ofinsulating material Report Number: MLT9806P15004 FCC ID: FI7MREFSG6

NILT MAX LIGHT : MEASUREMENT REPORT Page: 19/19 Appendix I— EUT Test SETUP MEASUREMENT OF RADIATED EMISSI Antenna Tower Receiver Antenna Ground Plane D :::::: RF Test Receiver Report Number: MLT9I806P15004 FCC ID: FIZMREF5S6


Document Created: 2001-05-24 06:52:14
Document Modified: 2001-05-24 06:52:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC