Test Report

FCC ID: DWNINSTEON1

Test Report

Download: PDF
FCCID_661238

6 Randolph Way Advanced Hillsborough, NJ 08844 Compliance Laboratory Tel: (908) 927 9288 Fax: (908) 927 0728 ELECTROMAGNETIC EMISSION COMPLIANCE REPORT of INSTEON TO RTS INTERFACE MODEL: INSTEON FCC ID: DWNINSTEON1 May 5, 2006 This report concerns (check one): Original grant x Class II change Equipment type: Low Power Intentional Radiator Deferred grant requested per 47 CF 0.457(d)(1)(ii)? yes no x If yes, defer until: (date) Company agrees to notify the Commission by (date) of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? yes no x If no, assumed Part 15, Subpart B for unintentional radiators - the new 47 CFR [10-1-90 Edition] provision. Report prepared for: Somfy System, Inc. Report prepared by: Advanced Compliance Lab Report number: 0048-060323-01 The test result in this report IS supported and covered by the NVLAP accreditation

FCC ID: DWNINSTEON1 Table of Contents Report Cover Page.........................................................................................................1 Table of Contents ...........................................................................................................2 Figures.............................................................................................................................3 1. GENERAL INFORMATION ...................................................................................4 1.1 Verification of Compliance .........................................................................4 1.2 Equipment Modifications............................................................................5 1.3 Product Information....................................................................................6 1.4 Test Methodology.........................................................................................6 1.5 Test Facility ..................................................................................................6 1.6 Test Equipment ............................................................................................6 1.7 Statement of the Document Use..................................................................7 2. PRODUCT LABELING............................................................................................8 3. SYSTEM TEST CONFIGURATION ......................................................................9 3.1 Justification ..................................................................................................9 3.2 Special Accessories.......................................................................................9 3.3 Configuration of Tested System .................................................................9 4. SYSTEM SCHEMATICS .........................................................................................13 5. CONDUCTED EMISSION DATA ..........................................................................14 5.1 Test Methods and Conditions .....................................................................14 5.2 Test Data .......................................................................................................14 6. RADIATED EMISSION DATA ...............................................................................17 6.1 Field Strength Calculation ..........................................................................17 6.2 Test Methods and Conditions .....................................................................17 6.2 Test Data .......................................................................................................17 6.4. Occupied Bandwidth ..................................................................................19 7. PHOTOS OF TESTED EUT ....................................................................................22 ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 2

FCC ID: DWNINSTEON1 Figures Figure 2.1 FCC ID Label...............................................................................................8 Figure 2.2 Location of Label on Back of the EUT ......................................................8 Figure 3.1 Radiated Test Setup, Position 1..................................................................10 Figure 3.2 Radiated Test Setup, Position 2..................................................................10 Figure 3.3 Radiated Test Setup, Position 3..................................................................11 Figure 3.4 Conducted Test Setup, Front......................................................................12 Figure 3.5 Conducted Test Setup, Rear .......................................................................12 Figure 4.1 EUT Schematics...........................................................................................13 Figure 5.1 Line Conducted............................................................................................15 Figure 5.2 Neutral Conducted .....................................................................................16 Figure 6.1 Bandwidth Plot ............................................................................................19 Figure 6.2 Pulse Train Timing .....................................................................................19 Figure 7.1 Front View....................................................................................................21 Figure 7.2 Rear View .....................................................................................................22 Figure 7.3 Inside View, Cover Opened ........................................................................23 Figure 7.4 Component Side...........................................................................................24 Figure 7.5 Foil Side ........................................................................................................25 Figure 7.6 Component Side /PCB1...............................................................................26 Figure 7.7 Foil Side /PCB1 ............................................................................................27 ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 3

FCC ID: DWNINSTEON1 1. GENERAL INFORMATION 1.1 Verification of Compliance EUT: INSTEON TO RTS INTERFACE Model: INSTEON Applicant: SOMFY SYSTEM, INC. Test Type: FCC Part 15C CERTIFICATION (15.231: a) Result: PASS Tested by: ADVANCED COMPLIANCE LABORATORY Test Date: May 5, 2006 Report Number: 0048-060323-01 The above equipment was tested by Compliance Laboratory, Advanced Technologies, Inc. for compliance with the requirement set forth in the FCC rules and regulations Part 15 subpart C. This said equipment in the configuration described in the report, shows the maximum emission levels emanating from equipment are within the compliance requirements. The estimated uncertainty of the test result is given as following. The method of uncertainty calculation is provided in Advanced Compliance Lab. Doc. No. 0048-01-01. Prob. Dist. Uncertainty(dB) Uncertainty(dB) Uncertainty(dB) 30-1000MHz 1-6.5GHz Conducted Combined Std. Uncertainty uc norm. ±2.36 ±2.99 ±1.83 ____________________ Wei Li Date: May 5, 2006 Lab Manager Advanced Compliance Lab ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 4

FCC ID: DWNINSTEON1 1.2 Equipment Modifications N/A ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 5

FCC ID: DWNINSTEON1 1.3 Product Information System Configuration ITEM DESCRIPTION FCC ID CABLE Product INSTEON TO RTS DWNINSTEON1 INTERFACE INSTEON (1) Housing PLASTICS Power Supply 120 VAC Operation Freq. 433.42MHz Device Type Periodic Operation Receiver RTS Receiver DoC (1) EUT submitted for grant. 1.4 Test Methodology Radiated tests were performed according to the procedures in ANSI C63.4-2003 at an antenna to EUT distance of 3 meters. 1.5 Test Facility The open area test site and conducted measurement facility used to collect the radiated and conducted data are located at Hillsborough, New Jersey. This site has been accepted by FCC to perform measurements under Part 15 or 18 in a letter dated May 19, 1997 (Refer to: 31040/PRV 1300F2). The NVLAP Lab code for accreditation of FCC EMC Test Method is: 200101-0. 1.6 Test Equipment Manufacture Model Serial No. Description Last Cal Cal Due dd/mm/y dd/mm/y y y Hewlett-Packard HP8546A 3448A00290 EMI Receiver 12/01/06 12/01/07 EMCO 3104C 9307-4396 20-300MHz Biconical Antenna 12/02/06 12/02/07 EMCO 3146 9008-2860 200-1000MHz Log-Periodic Antenna 09/02/06 09/02/07 Fischer Custom LISN-2 900-4-0008 Line Impedance Stabilization Networks 23/08/05 23/08/06 Fischer Custom LISN-2 900-4-0009 Line Impedance Stabilization Networks 23/08/05 23/08/06 EMCO 6502 2665 10KHz-30MHz Active Loop Antenna 27/02/06 27/02/07 EMCO 3115 4945 Double Ridge Guide Horn Antenna 11/08/05 11/08/06 All Test Equipment Used are Calibrated Traceable to NIST Standards. ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 6

FCC ID: DWNINSTEON1 1.7 Statement for the Document Use This report shall not be reproduced except in full, without the written approval of the laboratory. And this report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 7

FCC ID: DWNINSTEON1 2. PRODUCT LABELING FCC ID: DWNINSTEON1 Figure 2.1 FCC ID Label This device complies with part 15 of the FCC Rules. Operating is subject to the following two conditions: (1) This Figure 2.2 Location of Label on the Side of EUT device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Figure 2.1 FCC ID Label FCC Label Figure 2.2 FCC ID Label Location ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 8

FCC ID: DWNINSTEON1 3. SYSTEM TEST CONFIGURATION 3.1 Justification The system was configured for testing in a typical fashion (as a customer would normally use it). And its antenna was permanently attached to the EUT. Testing was performed as EUT was operated continuously. 3.2 Special Accessories N/A 3.3 Configuration of Tested System Figure 3.1 to Figure 3.5 illustrate this system, which is tested standing along. ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 9

FCC ID: DWNINSTEON1 Figure 3.1 Radiated Test Setup, position 1-X Figure 3.2 Radiated Test Setup, position 2-Y ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 10

FCC ID: DWNINSTEON1 Figure 3.3 Radiated Test Setup, position 3-Z ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 11

FCC ID: DWNINSTEON1 Figure 3.4 Conducted Setup- Front Figure 3.5 Conducted Setup- Rear ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 12

FCC ID: DWNINSTEON1 4. SYSTEM SCHEMATICS See Attachment. Figure 4.1 System Schematics ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 13

FCC ID: DWNINSTEON1 5. CONDUCTED EMISSION DATA 5.1 Test Methods and Conditions The EUT was under normal operational mode during the conducted emission test. EMI Receiver was scanned from 150KHz to 30MHz with maximum hold mode for maximum emission. Recorded data was sent to the plotter to generate output in linear format. At the input of the spectrum analyzer, a HP transient limiter is inserted for protective purpose. This limiter has a 10 dB attenuation in the range of 150KHZ to 30MHZ. That factor was automatically compensated by the receiver, so the readings are the corrected readings. The reference of the plot is the CISPR 22 Class B limit in Figure 5.1 through Figure 5.2. Conducted Emission Technical Requirements Class A Class B Frequency Range Quasi-Peak Average Quasi-Peak Average dBuV dBuV DBuV dBuV 150kHz –0.5MHz 79 (8912uV) 66 (1995uV) 66-56 56-46 0.5MHz-30MHz 73 (4467uV) 60 (1000uV) --- --- 0.5MHz- 5MHz --- --- 56 46 (250uV) 5MHz-30MHz --- --- 60 50 Emissions that have peak values close to the specification limit (if any) are also measured in the quasi- peak mode to determine compliance. 5.2 Test Data Figure 5.1-5.2 show the neutral and line conducted emissions for the standard operation. Six Highest Data for AC Line Conducted Emissions Frequency (MHz) 0.152 0.155 0.200 28.75 28.82 - Line(L)/Neutral(N) L N N N L Peak Reading (dBuV) 20.0 19.8 18.0 26.3 23.1 - Class B Limit (average) 55 55 53 50 50 Margin (dB) -35.0 -35.2 -35.0 -23.7 -26.9 Test Personnel: Tester Signature: Date: May 5, 2006 Typed/Printed Name: Edward Lee ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 14

FCC ID: DWNINSTEON1 Fig. 5.1 Conducted Emission-Line ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 15

FCC ID: DWNINSTEON1 Fig. 5.2 Conducted Emission- Neutral ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 16

FCC ID: DWNINSTEON1 6. RADIATED EMISSION DATA 6.1 Field Strength Calculation The corrected field strength is automatically calculated by EMI Receiver using following: FS = RA +AF + CF + AG where FS: Corrected Field Strength in dBµV/m RA: Amplitude of EMI Receiver before correction in dBµV AF: Antenna Factor in dB/m CF: Cable Attenuation Factor in dB AG: Built-in Preamplifier Gain in dB (Stored in receiver as part of the calibration data) The pulse train timing plots are showed in Figure 6.2. The pulse train timing plots as follows: The total time for each pulse train is 139.62 ms, The short pulse is 0.640ms, The middle pulse is 2.5 ms, The long pulse is 4.8m Coeff. =(56x0.640+1x4.8+4x2.5+(2.88-2.5))/(71.68+5.44+22.88)= 51.02/100=0.51 The maximum average field strength should be 0.51 of the peak field strength measured. So we use peak value minus 5.85dB as calculated maximum average field strength. 6.2 Test Methods and Conditions The initial step in collecting radiated data is a EMI Receiver scan of the measurement range below 30MHz using peak detector and 9KHz IF bandwidth / 30KHz video bandwidth. For the range 30MHz - 1GHz, 120KHz IF bandwidth / 120KHz video bandwidth are used. Both bandwidths are 1MHz for above 1GHz measurement. Up to 10th harmonics were investigated. 6.3 Test Data The following data lists the significant emission frequencies, polarity and position, peak reading of the EMI Receiver, calculated average reading, the FCC limit, and the difference between the peak reading and the limit. Explanation of the correction and calculation are given in section 6.1. Test Personnel: Typed/Printed Name: Edward Lee Date: May 5, 2006 ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 17

FCC ID: DWNINSTEON1 Radiated Test Data Frequenc Polarity Height Azimuth Peak Calculated FCC Difference y [H or V], Reading Average 3m Limit from limit Position (m) (Degree) (dBµV/m) Reading (dBµV/m) (dB) (MHz) (X,Y,Z) (dBµV/m 433.4 H,X(1) 1.4 20 84.1 78.25 80.8(3) -2.55 866.8 H,X 1.3 20 48.2 42.35 60.8(4) -18.45 1300.3 H,X 1.3 10 55.9 50.05 54.0(2) -3.95 1734 H,X 1.4 10 47.8 41.95 60.8 -18.85 2167.4 H,X 1.4 10 46.5 40.65 60.8 -20.15 433.4 V,X 1.2 30 85.5 79.65 80.8 -1.15 866.8 V,X 1.2 40 53.5 47.65 60.8 -13.15 1300.3 V,X 1.1 30 53.7 47.85 54.0 -6.15 1734 V,X 1.1 30 48.3 42.45 60.8 -18.35 2167.4 V,X 1.2 40 47.0 41.15 60.8 -19.65 2600.8 V,X 1.2 40 45.8 39.95 60.8 -20.85 433.4 H,Y 1.3 300 84.2 78.35 80.8 -2.45 866.8 H,Y 1.3 310 51.1 45.25 60.8 -15.55 1300.3 H,Y 1.3 280 54.2 48.35 54.0 -5.65 1734 H,Y 1.3 290 47.0 41.15 60.8 -19.65 2167.4 H,Y 1.3 320 45.0 39.15 60.8 -21.65 433.4 V,Y 1.2 300 85.0 79.15 80.8 -1.65 866.8 V,Y 1.2 300 48.8 42.95 60.8 -17.85 1300.3 V,Y 1.2 300 56.5 50.65 54.0 -3.35 1734 V,Y 1.2 320 46.5 40.65 60.8 -20.15 2167.4 V,Y 1.3 320 45.7 39.85 60.8 -20.95 433.4 H,Z 1.3 40 82.4 76.55 80.8 -4.25 866.8 H,Z 1.4 40 49.6 43.75 60.8 -17.05 1300.3 H,Z 1.3 30 53.3 47.45 54.0 -6.55 1734 H,Z 1.3 20 46.8 40.95 60.8 -19.85 2167.4 H,Z 1.3 20 44.9 39.05 60.8 -21.75 433.4 V,Z 1.2 30 83.6 77.75 80.8 -3.05 866.8 V,Z 1.1 30 48.3 42.45 60.8 -18.35 1300.3 V,Z 1.1 20 52.2 46.35 54.0 -7.65 1734 V,Z 1.2 20 46.3 40.45 60.8 -20.35 (1) See Figure 3.1, 3.2 and 3.3 for definition of position X-1, Y-2, Z-3. (2) Restricted band. (3) Fundamental limit is 3750-12500 microvolts/meter linear interpolations (average reading). Per FCC 15.231(a). (4) Spurious limit is 375-1250 microvolts/meter linear interpolations (average reading). Per 15.231(a). (5) Peak Reading Limit =Average reading Limit +20dB. *---Average Reading ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 18

FCC ID: DWNINSTEON1 6.4 Occupied Bandwidth The bandwidth of the emission shall be no wider than 0.25% of the center frequency, in this case, 1.084MHz(433.5x0.25%). Bandwidth is determined at the points 20dB down from the modulated carrier. Figure 5.2 shows the occupied bandwidth plot. Figure 6.1 Occupied Bandwidth ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 19

FCC ID: DWNINSTEON1 Figure 6.2 (a) Pulse Train Timing ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 20

FCC ID: DWNINSTEON1 Figure 6.2(b) Pulse Train Timing ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 21

FCC ID: DWNINSTEON1 7. PHOTOS OF TESTED EUT The following photos show the inside details of the EUT. ——————————————————————————————————————————————— Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 22


Document Created: 2006-05-07 23:29:52
Document Modified: 2006-05-07 23:29:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC