user manual

FCC ID: BOU-AEA7100

Users Manual

Download: PDF
FCCID_1819397

Always there to help you Register your product and get support at www.philips.com/welcome Question? Contact Philips AEA7100 / 17 AEA7000 / 07 AEA7100 / 37 AEA7000 / 37 User manual

Contents 1 Important 2 Safety 2 Notice 3 2 Your Wireless Microphone and Bluetooth Docking Speaker 6 Introduction 6 What's in the box 6 Overview of the unit 6 3 Get started 8 Connect power 8 Swith on the Bluetooth docking speaker 8 Install/replace microphone batteries 8 4 Play 10 Sing along through the wireless microphone 10 Play from a Bluetooth enabled device 11 Play and charge your iPad through the dock connector directly 12 Play from an external device 13 5 Product information 14 Specifications 14 6 Troubleshooting 15 MAV-AEA7000-Troubleshooting- Failed to set up connection between the microphone and speaker 15 EN 1

1 Important h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. i Do not defeat the safety purpose of the polarized or grounding-type plug. Safety A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. This 'bolt of lightning' indicates uninsulated material within the device may cause an electrical shock. For the safety of everyone in your household, please do not remove the covering. The 'exclamation mark' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. j Protect the power cord from being WARNING: To reduce the risk of fire or electric walked on or pinched, particularly at shock, the device should not be exposed to rain plugs, convenience receptacles, and the or moisture and objects filled with liquids, such point where they exit from the apparatus. as vases, should not be placed on the device. k Only use attachments/accessories CAUTION: To prevent electric shock, fully specified by the manufacturer. insert the plug. (For regions with polarized plugs: To prevent electric shock, match wide l Use only with the cart, stand, tripod, blade to wide slot.) bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when Important Safety Instructions moving the cart/apparatus combination to avoid injury from tip-over. a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Do not use this apparatus near water. f Clean only with dry cloth. m Unplug this apparatus during lightning storms or when unused for long periods g Do not block any ventilation openings. of time. Install in accordance with the manufacturer's instructions. 2 EN

n Refer all servicing to qualified service Caution personnel. Servicing is required when the apparatus has been damaged in any • Risk of leakage: Only use the specified type of batteries. Do not mix new and used batteries. Do not mix way, such as power-supply cord or plug different brands of batteries. Observe correct polarity. is damaged, liquid has been spilled or Remove batteries from products that are not in use for objects have fallen into the apparatus, the a longer period of time. Store batteries in a dry place. apparatus has been exposed to rain or • Risk of injury: Wear gloves when handling leaking batteries. Keep batteries out of reach of children and moisture, does not operate normally, or pets. has been dropped. • Risk of explosion: Do not short circuit batteries. Do not expose batteries to excessive heat. Do not throw o Battery usage CAUTION – To prevent batteries into the fire. Do not damage or disassemble battery leakage which may result in bodily batteries. Do not recharge non-rechargeable batteries. injury, property damage, or damage to the unit: • Install all batteries correctly, + and - as marked on the unit. • Remove batteries when the unit is not Notice used for a long time. • Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/ Notice of compliance hazardouswaste/perchlorate. Modifications p Apparatus shall not be exposed to The user is cautioned that changes or dripping or splashing, keep it away from modifications not expressly approved by the direct sunlight,naked flames or heat. party responsible for compliance could void the user’s authority to operate the equipment. q Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. FCC & RSS compliance statement This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the Warning following two conditions: • Never remove the casing of this apparatus. • Never lubricate any part of this apparatus. a This device may not cause harmful • Never place this apparatus on other electrical interference, and equipment. • Keep this apparatus away from direct sunlight, naked b This device must accept any interference flames or heat. received, including interference that may • Ensure that you always have easy access to the power cause undesired operation. cord, plug or adaptor to disconnect this apparatus from the power. FCC Radiation Exposure Statement Risk of overheating! Never install this apparatus This equipment complies with FCC’s and IC’s in a confined space. Always leave a space of RF radiation exposure limits set forth for an at least four inches around this apparatus for uncontrolled environment. The antenna(s) ventilation. Ensure curtains or other objects used for this transmitter must be installed and never cover the ventilation slots on this operated to provide a separation distance of apparatus. at least 20 cm from all persons and must not Information about the use of batteries: be collocated or operating in conjunction with EN 3

any other antenna or transmitter. Installers must The correct disposal of these products helps ensure that 20cm separation distance will be prevent potentially negative consequences on maintained between the device (excluding its the environment and human health. handset) and users. Your product contains batteries, which cannot be disposed of with normal household waste. FCC rules Please inform yourself about the local rules on This equipment has been tested and found separate collection of batteries. The correct to comply with the limits for a Class B digital disposal of batteries helps prevent potentially device, pursuant to Part 15 of the FCC Rules. negative consequences on the environment and These limits are designed to provide reasonable human health. protection against harmful interference in a Please visit www.recycle.philips.com for residential installation. This equipment generates, additional information on a recycling center in uses and can radiate radio frequency energy your area. and, if not installed and used in accordance with Environmental information the instructions, may cause harmful interference All unnecessary packaging has been omitted. to radio communications. However, there is no We have tried to make the packaging easy to guarantee that interference will not occur in a separate into three materials: cardboard (box), particular installation. polystyrene foam (buffer) and polyethylene If this equipment does cause harmful (bags, protective foam sheet.) interference to radio or television reception, Your system consists of materials which can which can be determined by turning the be recycled and reused if disassembled by equipment off and on, the user is encouraged a specialized company. Please observe the to try to correct the interference by one or local regulations regarding the disposal of more of the following measures: packaging materials, exhausted batteries and old • Reorient or relocate the receiving antenna. equipment. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. “Made for iPad” means that an electronic accessory has been designed to connect Canada: specifically to iPad, and has been certified by This Class B digital apparatus complies with the developer to meet Apple performance Canadian ICES-003. standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that Disposal of your old product and the use of this accessory with iPad may affect batteries wireless performance. Your product is designed and manufactured iPad is a trademark of Apple Inc., registered in with high quality materials and components, the U.S. and other countries. which can be recycled and reused. The Bluetooth® word mark and logos are Never dispose of your product with other registered trademarks owned by Bluetooth household waste. Please inform yourself about SIG, Inc. and any use of such marks by Philips is the local rules on the separate collection of under license. electrical and electronic products and batteries. 4 EN

Note • The type plate is located on the back of the unit. EN 5

2 Your Wireless • • Wireless microphone Bluetooth docking speaker Microphone • • AC power cord 3 X AAA batteries and Bluetooth • • Quick start guide Safety sheet Docking Speaker Overview of the unit Wireless microphone Congratulations on your purchase, and welcome to Philips! To fully benefit from the b support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The d model number and serial number are on the back of the apparatus. Write the numbers here: c Model No. __________________________ Serial No. ___________________________ Introduction a With the wireless microphone and Bluetooth docking speaker, you can: a Line out socket • dock your iPad onto the speaker to • (To use the microphone separately) sing along with music from the app connect to the MIC input socket of an (StarMaker Karaoke + Auto-Tune®) existing audio system. through the wireless microphone. With the Bluetooth docking speaker, you can: b Battery compartment • play music from a Bluetooth enabled c ON/OFF device that supports A2DP (Advanced • Switch the microphone on or off. Audio Distribution Profile). • charge or play music from your iPad d Power indicator directly through the dock connector. • Light up red when the wireless • play music from other audio devices microphone is switched on. through the AUDIO-IN socket. • Flash red when the battery level is low. What's in the box Check and identify the contents of your package: 6 EN

b a c de h gf a • Turn the unit on/off. b Power/Bluetooth indicator • Indicate the power/Bluetooth status. c -/+ • Adjust volume. d • (Press) pair with a Bluetooth enabled device that supports A2DP (Advanced Audio Distribution Profile). • (Press and hold) pair with the wireless microphone in case automatic pairing fails. e Dock for iPad f SOFTWARE UPGRADE (for engineering use only) g AUDIO-IN • Connect an external audio player through a 3.5mm audio input cable (not supplied). h AC power socket EN 7

3 Get started • To switch the unit on from standby mode, press again. Tip Always follow the instructions in this chapter in sequence. • If the speaker stays idle for more than 15 minutes, it switches to standby mode automatically. Connect power Caution Install/replace microphone • Risk of product damage! Make sure that the power batteries supply voltage corresponds to the voltage printed on the back of the unit. Caution • Risk of electric shock! When you unplug the AC power cord, always pull the plug from the socket. Never pull • Risk of explosion! Keep batteries away from heat, the cord. sunshine, or fire. Never discard batteries in fire. • Before you connect the AC power cord, make sure that • Danger of explosion if batteries are incorrectly you have completed all the other connections. replaced. Replace only with the same or equivalent type. • Batteries contain chemical substances, so they should be disposed of properly. 1 Open the battery compartment and take out the battery cartridge. • Connect the AC power cord to • the AC MAINS~ socket on the back of the Bluetooth docking speaker. • the wall power socket. 2 Insert 3 x AAA batteries (supplied) into Swith on the Bluetooth the cartridge with correct polarity (+/-) as docking speaker indicated. • Press on the top of the Bluetooth docking speaker. » The power indicator lights up white. • To switch the unit to standby mode, press on the top panel. 8 EN

3 Push back the battery cartridge, then close the battery compartment. Note • If you are not going to use the microphone for a long time, remove the batteries. • New batteries installed in the microphone support up to 30 hours of continuous use. • When the power indicator flashes red, it indicates that the power level is low and you need to replace the batteries. EN 9

4 Play Sing along through the wireless microphone Note • The effective operation range between the wireless microphone and Bluetooth docking speaker is 4 Slide the ON/OFF switch on the wireless approximately 10 meters (30 feet). microphone to the ON position. • If the Bluetooth docking speaker is already paired and » The Bluetooth indicator on the connected with another Bluetooth enabled device, Bluetooth docking speaker flashes blue. press on the top panel of the speaker to remove the existing Bluetooth connection. » The wireless microphone starts to pair • Before you dock your iPad onto the Bluetooth docking with the Bluetooth docking speaker speaker, you can use the supplied bumper for better support if necessary. automatically. » After successful pairing and connection, the Bluetooth indicator turns solid 1 Dock your iPad onto the Bluetooth blue. docking speaker. » A prompt pops up on the iPad screen, asking you to install the relevant app. 5 Find and download a tutorial from StarMaker Karaoke + Auto-Tune®, then 2 Tap YES on the prompt to install the app tap Sing->RECORD for how to sing along (StarMaker Karaoke + Auto-Tune®) from through the wireless microphone and Apple App Store. Bluetooth docking speaker. 3 After successful installation, run StarMaker Karaoke + Auto-Tune® on the iPad. 10 EN

Play from a Bluetooth enabled device Note • The effective operation range between the Bluetooth docking speaker and your Bluetooth enabled device is approximately 10 meters (30 feet). • To pair with a Bluetooth enabled mobile device, make sure that: no iPad is docked; or you have stopped music play on your docked iPad and the StarMaker Karaoke + Auto-Tune® app is not running. • To pair with a new mobile device, you can press to remove the existing Bluetooth connection. • To play from a Bluetooth-enabled device, make sure that you are not playing music from your iPad docked 6 Select a song from StarMaker Karaoke + on the Bluetooth docking speaker. Auto-Tune® and sing along through the wireless microphone. 1 Press on the top of the Bluetooth docking speaker. » The Bluetooth indicator flashes blue. 7 Use -/+ on the top of the Bluetooth docking speaker to adjust volume. Tip • If the wireless microphone stays disconnected from the speaker for more than 15 minutes, it switches to 2 Enable Bluetooth on your device that standby mode automatically. To switch it on again, you supports A2DP (Advanced Audio need to slide the ON/OFF switch on the microphone Distribution Profile). to the OFF position and then back to the ON position. • You can use controls available on the app to adjust sound effects. • If you experience howling or echo, try to increase the distance between the microphone and speaker or adjust the angle of the microphone towards the speaker. EN 11

Play and charge your iPad through the dock connector directly Compatible iPad This unit supports play and charge of the following iPad models: • New iPad • iPad 2 • iPad 3 Select 'PHILIPS_AEA7100/17' on your Bluetooth enabled device (if necessary, Load the iPad input '0000' as the paring password). » After successful pairing and connection, • Dock your iPad. the Bluetooth indicator on the speaker turns solid blue and the speaker beeps twice. To remove the iPad • Pull the iPad out of the dock. 4 Start music play on your Bluetooth enabled device. Listen to the iPad 1 Make sure that the iPad has been loaded correctly. 2 Start music play on your iPad. » The connected iPad starts to play. 3 Use -/+ on the top of the Bluetooth docking speaker to adjust volume. 5 Use -/+ on the top of the Bluetooth Charge the iPad docking speaker to adjust volume. The docked iPad begins to charge as soon as the unit is connected to AC power. 12 EN

Play from an external device You can also listen to an external audio player through the Bluetooth docking speaker. AUDIO-IN 1 Connect a 3.5mm audio cable to: • the AUDIO-IN socket on the back of the Bluetooth docking speaker. • the headphone socket on an external audio player. 2 Start music play on the external audio player. 3 Use -/+ on the top of the Bluetooth docking speaker to adjust volume. EN 13

5 Product Dimensions (W x H x D) • Main Unit 300 x 162 x 148mm information • Microphone 162 x 333 x 162mm Weight 2.5 kg • With Packing 1.3kg Note • Speaker 0.3kg • Product information is subject to change without prior • Microphone notice. Specifications Amplifier Rated Output Power 2W RMS Signal to Noise Ratio >70dB Aux-in Link 600 mV RMS, 10 kohm Speakers Speaker Impedance 4 ohm Speaker Driver 70mm full range Sensitivity > 84dB/1m/1W Bluetooth Bluetooth V2.1 specification Supported Profiles AD2P V1.2 Advanced features Echo and noise cancelation Range 10 m/33 feet line of sight General information AC power 120 V~; 60 Hz Operation Power 20 W Consumption 14 EN

6 Troubleshooting MAV-AEA7000- Troubleshooting-Failed to set Warning up connection between the • Never remove the casing of this apparatus. microphone and speaker Failed to set up connection between the To keep the warranty valid, never try to repair microphone and speaker the system yourself. • Check whether both the wireless If you encounter problems when using this microphone and Bluetooth docking apparatus, check the following points before speaker are switched on. requesting service. If the problem remains • Make sure that the wireless unsolved, go to the Philips web site (www. microphone and Bluetooth docking philips.com/welcome). When you contact speaker are within the the effective Philips, ensure that the apparatus is nearby operation range, that is, approximately and the model number and serial number are 10 meters (30 feet). available. • Press and hold on the top of the No power to the Bluetooth docking speaker Bluetooth docking speaker for more • Make sure that the AC power plug of the than 10 seconds to set up wireless device is connected properly. connection manually. • Make sure that there is power at the AC Howling or echo from the wireless outlet. microphone • As a power-saving feature, the speaker • Adjust volume. switches to standby mode automatically • Increase the distance between the after staying idle for more than 15 minutes. microphone and speaker or adjust the Switch on the speaker again (see 'Swith on angle of the microphone towards the the Bluetooth docking speaker' on page 8). speaker. No power to the wireless microphone No response from the Bluetooth docking • The batteries may be installed incorrectly speaker or drained. Install or replace the batteries • Disconnect and reconnect the AC power properly (see 'Install/replace microphone plug, and then switch on the device again. batteries' on page 8). • As a power-saving feature, the microphone switches to standby mode automatically after staying disconnected from the speaker for more than 15 minutes. To switch it on again, you need to slide the ON/OFF switch on the microphone to the OFF position and then back to the ON position. No sound or poor sound • Adjust volume. • Check the Bluetooth connection. • Check whether you have started music play on the connected device. EN 15

Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. Document order number: 000000000000


Document Created: 2012-10-18 19:14:47
Document Modified: 2012-10-18 19:14:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC