SAR Test Report

FCC ID: BCG-E2407

RF Exposure Info

Download: PDF
FCCID_1336224

FCC OET BULLETIN 65 SUPPLEMENT C IC RSS-102 ISSUE 4 SAR EVALUATION REPORT For 802.11 b/g/n + BT (2.1) EDR MODEL: A1367 FCC ID: BCG-E2407 IC: 579C-E2407 REPORT NUMBER: 10U13294-16C ISSUE DATE: August 27, 2010 Prepared for APPLE INC 1 INFINITE LOOP, MS-26A CUPERTINO, CA 95014 Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 Revision History Rev. Issue Date Revisions Revised By -- July 14, 2010 Initial Issue -- A August 19, 2010 Fixed some typos in the section 11.1 and 11.2 Devin Chang B August 25, 2010 Updated EUT description. Devin Chang C August 27, 2010 Updated report. Includes Devin Chang 1. Changed frequency range from 2412 - 2472 MHz to 2412 - 2462 MHz in the section 1 2. Added all SAR plots into report includes z-axis plot of the highest SAR measurement. See section 13 Page 2 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................................. 4 2. TEST METHODOLOGY ...................................................................................................................... 5 3. FACILITIES AND ACCREDITATION.................................................................................................. 5 4. CALIBRATION AND UNCERTAINTY................................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 6 4.2. MEASUREMENT UNCERTAINTY.............................................................................................. 7 5. EQUIPMENT UNDER TEST ............................................................................................................... 8 6. KDB 648474 SIMULTANEOUS TRANSMISSION CONSIDERATION............................................... 8 7. SYSTEM SPECIFICATIONS ............................................................................................................... 9 8. COMPOSITION OF INGREDIENTS FOR TISSUE SIMULATING LIQUIDS .................................... 10 9. LIQUID PARAMETERS CHECK....................................................................................................... 11 9.1. LIQUID CHECK RESULTS FOR 2450 MHZ............................................................................. 12 10. SYSTEM VERIFICATION ............................................................................................................. 13 10.1. SYSTEM CHECK RESULTS FOR D2450V2............................................................................ 13 11. OUTPUT POWER VERIFICATION............................................................................................... 16 11.1. WIFI RF OUTPUT POWER....................................................................................................... 16 11.2. BLUETOOTH RF OUTPUT POWER ........................................................................................ 16 12. SUMMARY OF TEST RESULTS.................................................................................................. 17 13. SAR TEST PLOTS........................................................................................................................ 18 14. ATTACHMENTS ........................................................................................................................... 24 15. ANTENNA LOCATIONS............................................................................................................... 25 16. TEST SETUP PHOTOS ................................................................................................................ 26 17. EXTERNAL PHOTOS................................................................................................................... 28 Page 3 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 1. ATTESTATION OF TEST RESULTS APPLE INC Company name: 1 INFINITE LOOP, MS-26A CUPERTINO, CA 95014 EUT description: 802.11 b/g/n + BT (2.1) EDR Model number: A1367 Serial number: CCQCV00JDCPC Device category:: Portable Exposure category: General Population/Uncontrolled Exposure Date tested: July 8, 2010 FCC / IC rule parts Frequency Range [MHz] Highest 1-g SAR (mW/g) Limit (mW/g) 15.247 / RSS-102 2412 – 2462 Body: 1.11 (Face up) 1.6 Applicable Standards Test Results FCC OET Bulletin 65 Supplement C 01-01 Pass IC RSS 102 Issue 4 Compliance Certification Services, Inc. (CCS) tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by CCS based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by CCS and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by CCS will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government (NIST Handbook 150, Annex A). This report is written to support regulatory compliance of the applicable standards stated above. Approved & Released For CCS By: Tested By: SUNNY SHIH DEVIN CHANG ENGINEERING SUPERVISOR EMC ENGINEER COMPLIANCE CERTIFICATION SERVICES COMPLIANCE CERTIFICATION SERVICES Page 4 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with FCC OET Bulletin 65 Supplement C 01-01, IC RSS 102 Issue 4 and the following specific FCC Test Procedures. o KDB 648474 D01 SAR Handsets Multi Xmiter and Ant, v01r05 o KDB 248227 D01 SAR meas for 802 11abg v01r02 3. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, California, USA. CCS is accredited by NVLAP, Laboratory Code 200065-0. The full scope of accreditation can be viewed at http://www.ccsemc.com. Page 5 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 4. CALIBRATION AND UNCERTAINTY 4.1. MEASURING INSTRUMENT CALIBRATION The measuring equipment utilized to perform the tests documented in this report has been calibrated in accordance with the manufacturer's recommendations, and is traceable to recognized national standards. Cal. Due date Name of Equipment Manufacturer Type/Model Serial No. MM DD Year Robot - Six Axes Stäubli RX90BL N/A N/A Robot Remote Control Stäubli CS7MB 3403-91535 N/A DASY4 Measurement Server SPEAG SEUMS001BA 1041 N/A Probe Alignment Unit SPEAG LB (V2) 261 N/A SAM Phantom (SAM1) SPEAG QD000P40CA 1185 N/A SAM Phantom (SAM2) SPEAG QD000P40CA 1050 N/A Oval Flat Phantom (ELI 4.0) SPEAG QD OVA001 B 1003 N/A Electronic Probe kit HP 85070C N/A N/A S-Parameter Network Analyzer Agilent 8753ES-6 MY40001647 11 22 2010 Signal Generator Agilent 8753ES-6 MY40001647 11 22 2010 E-Field Probe SPEAG EX3DV4 3531 2 22 2011 Data Acquisition Electronics SPEAG DAE3 V1 500 9 15 2010 System Validation Dipole SPEAG D2450V2 706 4 18 2013 Amplifier Mini-Circuits ZVE-8G 90606 N/A Amplifier Mini-Circuits ZHL-42W D072701-5 N/A Simulating Liquid SPEAG H2450 N/A Within 24 hrs of first test Simulating Liquid SPEAG M2450 N/A Within 24 hrs of first test Note: Per KDB 450824 D02 requirements for dipole calibration, CCS has adopted three years calibration intervals. On annual basis, each measurement dipole has been evaluated and is in compliance with the following criteria: 1. There is no physical damage on the dipole 2. System validation with specific dipole is within 10% of calibrated value. 3. Return-loss is within 20% of calibrated measurement ( test data on file in CCS) 4. Impedance is within 5Ω of calibrated measurement (test data on file in CCS) Page 6 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 4.2. MEASUREMENT UNCERTAINTY Measurement uncertainty for 300 MHz to 3 GHz averaged over 1 gram Component error, % Probe Distribution Divisor Sensitivity U (Xi), % Measurement System Probe Calibration (k=1) @ Body 2450 MHz 5.50 Normal 1 1 5.50 Axial Isotropy 1.15 Rectangular 1.732 0.7071 0.47 Hemispherical Isotropy 2.30 Rectangular 1.732 0.7071 0.94 Boundary Effect 0.90 Rectangular 1.732 1 0.52 Probe Linearity 3.45 Rectangular 1.732 1 1.99 System Detection Limits 1.00 Rectangular 1.732 1 0.58 Readout Electronics 0.30 Normal 1 1 0.30 Response Time 0.80 Rectangular 1.732 1 0.46 Integration Time 2.60 Rectangular 1.732 1 1.50 RF Ambient Conditions - Noise 3.00 Rectangular 1.732 1 1.73 RF Ambient Conditions - Reflections 3.00 Rectangular 1.732 1 1.73 Probe Positioner Mechanical Tolerance 0.40 Rectangular 1.732 1 0.23 Probe Positioning with respect to Phantom 2.90 Rectangular 1.732 1 1.67 Extrapolation, Interpolation and Integration 1.00 Rectangular 1.732 1 0.58 Test Sample Related Test Sample Positioning 2.90 Normal 1 1 2.90 Device Holder Uncertainty 3.60 Normal 1 1 3.60 Output Power Variation - SAR Drift 5.00 Rectangular 1.732 1 2.89 Phantom and Tissue Parameters Phantom Uncertainty (shape and thickness) 4.00 Rectangular 1.732 1 2.31 Liquid Conductivity - deviation from target 5.00 Rectangular 1.732 0.64 1.85 Liquid Conductivity - measurement 2.43 Normal 1 0.64 1.56 Liquid Permittivity - deviation from target 5.00 Rectangular 1.732 0.6 1.73 Liquid Permittivity - measurement 0.02 Normal 1 0.6 0.01 Combined Standard Uncertainty Uc(y) = 9.57 Expanded Uncertainty U, Coverage Factor = 2, > 95 % Confidence = 19.14 % Expanded Uncertainty U, Coverage Factor = 2, > 95 % Confidence = 1.52 dB Measurement uncertainty for 300 MHz to 3 GHz averaged over 10 gram Component error, % Probe Distribution Divisor Sensitivity U (Xi), % Measurement System Probe Calibration (k=1) @ Body 2450 MHz 5.50 Normal 1 1 5.50 Axial Isotropy 1.15 Rectangular 1.732 0.7071 0.47 Hemispherical Isotropy 2.30 Rectangular 1.732 0.7071 0.94 Boundary Effect 0.90 Rectangular 1.732 1 0.52 Probe Linearity 3.45 Rectangular 1.732 1 1.99 System Detection Limits 1.00 Rectangular 1.732 1 0.58 Readout Electronics 0.30 Normal 1 1 0.30 Response Time 0.80 Rectangular 1.732 1 0.46 Integration Time 2.60 Rectangular 1.732 1 1.50 RF Ambient Conditions - Noise 3.00 Rectangular 1.732 1 1.73 RF Ambient Conditions - Reflections 3.00 Rectangular 1.732 1 1.73 Probe Positioner Mechanical Tolerance 0.40 Rectangular 1.732 1 0.23 Probe Positioning with respect to Phantom 2.90 Rectangular 1.732 1 1.67 Extrapolation, Interpolation and Integration 1.00 Rectangular 1.732 1 0.58 Test Sample Related Test Sample Positioning 2.90 Normal 1 1 2.90 Device Holder Uncertainty 3.60 Normal 1 1 3.60 Output Power Variation - SAR Drift 5.00 Rectangular 1.732 1 2.89 Phantom and Tissue Parameters Phantom Uncertainty (shape and thickness) 4.00 Rectangular 1.732 1 2.31 Liquid Conductivity - deviation from target 5.00 Rectangular 1.732 0.43 1.24 Liquid Conductivity - measurement 2.43 Normal 1 0.43 1.04 Liquid Permittivity - deviation from target 5.00 Rectangular 1.732 0.49 1.41 Liquid Permittivity - measurement uncertainty 0.02 Normal 1 0.49 0.01 Combined Standard Uncertainty Uc(y), % = 9.35 Expanded Uncertainty U, Coverage Factor = 2, > 95 % Confidence = 18.69 % Expanded Uncertainty U, Coverage Factor = 2, > 95 % Confidence = 1.49 dB Page 7 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 5. EQUIPMENT UNDER TEST The Apple Model Number A1367 is an iPod Touch product. This is a 802.11 b/g/n + BT (2.1) EDR. The A1367 measures 110.8 mm (4.362 inches) long x 58.9 mm (2.318 inches) wide x 7.2 mm (0.283 inches) thick and weighs 99.2 grams (3.5 oz.). The rechargeable battery is not user accessible. The Apple A1367 comes with one of three memory configurations, 8 / 16 / 32 / 64 Giga Bytes for storing music, video or data. The Apple A1367 function is fully compatible with Apple’s iTunes software. The Apple A1367 in box materials include; Apple ear buds (no microphone), and 30 pin to USB cable. Normal operation: Hand-held, or Worn on body (LCD facing-up; LCD facing-down) with 0 mm separation distance from EUT to body. Body Worn Accessory Headset Antenna-to-antenna 0 cm - WiFi (802.11g)-to-Bluetooth antenna separation distances: (WiFi-to-Bluetooth are sharing a common antenna) Simultaneous transmission: WiFi can not transmit simultaneously with Bluetooth 6. KDB 648474 SIMULTANEOUS TRANSMISSION CONSIDERATION SUMMARY OF SAR EVALUATION FOR A DEVUCE WITH MULTIPLE TRANSMITTERS Individual Transmitter Stand-alone SAR WiFi Yes Bluetooth Stan-alone SAR not required due to the output ≤ 60/f SIMULTANEOUS TRANSMISSION WiFi can not transmit simultaneously with Bluetooth Page 8 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 7. SYSTEM SPECIFICATIONS The DASY4 system for performing compliance tests consists of the following items: • A standard high precision 6-axis robot (Stäubli RX family) with controller, teach pendant and software. An arm extension for accommodating the data acquisition electronics (DAE). • A dosimetric probe, i.e., an isotropic E-field probe optimized and calibrated for usage in tissue simulating liquid. The probe is equipped with an optical surface detector system. • A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, AD-conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC. • The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts. • A probe alignment unit which improves the (absolute) accuracy of the probe positioning. • A computer operating Windows 2000 or Windows XP. • DASY4 software. • Remote controls with teach pendant and additional circuitry for robot safety such as warning lamps, etc. • The SAM twin phantom enabling testing left-hand and right-hand usage. • The device holder for handheld mobile phones. • Tissue simulating liquid mixed according to the given recipes. • Validation dipole kits allowing validating the proper functioning of the system. Page 9 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 8. COMPOSITION OF INGREDIENTS FOR TISSUE SIMULATING LIQUIDS The following tissue formulations are provided for reference only as some of the parameters have not been thoroughly verified. The composition of ingredients may be modified accordingly to achieve the desired target tissue parameters required for routine SAR evaluation. Ingredients Frequency (MHz) (% by weight) 450 835 900 1800 - 1900 2450 Tissue Type Head Body Head Body Head Body Head Body Head Body Water 38.56 51.16 41.45 52.4 41.05 56.0 54.9 40.4 62.7 73.2 Salt (NaCl) 3.95 1.49 1.45 1.4 1.35 0.76 0.18 0.5 0.5 0.04 Sugar 56.32 46.78 56.0 45.0 56.5 41.76 0.0 58.0 0.0 0.0 HEC 0.98 0.52 1.0 1.0 1.0 1.21 0.0 1.0 0.0 0.0 Bactericide 0.19 0.05 0.1 0.1 0.1 0.27 0.0 0.1 0.0 0.0 Triton X-100 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 36.8 0.0 DGBE 0.0 0.0 0.0 0.0 0.0 0.0 44.92 0.0 0.0 26.7 Dielectric Constant 43.42 58.0 42.54 56.1 42.0 56.8 39.9 54.0 39.8 52.5 Conductivity (S/m) 0.85 0.83 0.91 0.95 1.0 1.07 1.42 1.45 1.88 1.78 Salt: 99+% Pure Sodium Chloride Sugar: 98+% Pure Sucrose Water: De-ionized, 16 MΩ+ resistivity HEC: Hydroxyethyl Cellulose DGBE: 99+% Di(ethylene glycol) butyl ether, [2-(2-butoxyethoxy)ethanol] Triton X-100 (ultra pure): Polyethylene glycol mono [4-(1,1, 3, 3-tetramethylbutyl)phenyl]ether Page 10 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 9. LIQUID PARAMETERS CHECK The simulating liquids should be checked at the beginning of a series of SAR measurements to determine of the dielectric parameters are within the tolerances of the specified target values. For frequencies in 300 MHz to just under 2 GHz, the measured conductivity and relative permittivity should be within ± 5% of the target values. For frequencies in the range of 2–3 GHz and above the measured conductivity should be within ± 5% of the target values. The measured relative permittivity tolerance can be relaxed to no more than ± 10%. Reference Values of Tissue Dielectric Parameters for Head and Body Phantom The head tissue dielectric parameters recommended by the IEEE SCC-34/SC-2 in IEEE Standard 1528 have been incorporated in the following table. These head parameters are derived from planar layer models simulating the highest expected SAR for the dielectric properties and tissue thickness variations in a human head. Other head and body tissue parameters that have not been specified in P1528 are derived from the tissue dielectric parameters computed from the 4-Cole-Cole equations and extrapolated according to the head parameters specified in IEEE Standard 1528. Head Body Target Frequency (MHz) εr σ (S/m) εr σ (S/m) 150 52.3 0.76 61.9 0.8 300 45.3 0.87 58.2 0.92 450 43.5 0.87 56.7 0.94 835 41.5 0.9 55.2 0.97 900 41.5 0.97 55 1.05 915 41.5 0.98 55 1.06 1450 40.5 1.2 54 1.3 1610 40.3 1.29 53.8 1.4 1800 – 2000 40 1.4 53.3 1.52 2450 39.2 1.8 52.7 1.95 3000 38.5 2.4 52 2.73 5800 35.3 5.27 48.2 6 (εr = relative permittivity, σ = conductivity and ρ = 1000 kg/m3) Page 11 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 9.1. LIQUID CHECK RESULTS FOR 2450 MHZ Simulating Liquid Dielectric Parameters for Body 2450 MHz Room Ambient Temperature = 24°C; Relative humidity = 41% Measured by: Devin Chang f (MHz) Liquid Parameters Measured Target Delta (%) Limit (%) e' 52.71 Relative Permittivity (єr ): 52.712 52.7 0.02 ±5 2450 e" 14.65 Conductivity (σ): 1.997 1.95 2.43 ±5 Liquid Check Ambient temperature: 24 deg. C; Liquid temperature: 23 deg. C July 08, 2010 09:38 AM Frequency e' e'' 2400000000. 52.9076 14.4447 2405000000. 52.8767 14.4579 2410000000. 52.8600 14.4928 2415000000. 52.8378 14.4977 2420000000. 52.8254 14.5293 2425000000. 52.7897 14.5511 2430000000. 52.7745 14.5742 2435000000. 52.7635 14.5874 2440000000. 52.7576 14.6116 2445000000. 52.7330 14.6371 2450000000. 52.7119 14.6546 2455000000. 52.6810 14.6632 2460000000. 52.6841 14.6901 2465000000. 52.6591 14.7191 2470000000. 52.6357 14.7393 2475000000. 52.6271 14.7516 2480000000. 52.6000 14.7768 2485000000. 52.5884 14.8034 2490000000. 52.5697 14.8202 2495000000. 52.5494 14.8474 2500000000. 52.5235 14.8722 The conductivity (σ) can be given as: σ = ωε0 e''= 2 π f ε0 e'' where f = target f * 106 ε0 = 8.854 * 10-12 Page 12 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 10. SYSTEM VERIFICATION The system performance check is performed prior to any usage of the system in order to verify SAR system measurement accuracy. The system performance check verifies that the system operates within its specifications of ±10%. System Performance Check Measurement Conditions • The measurements were performed in the flat section of the SAM twin phantom filled with Head or Body simulating liquid of the following parameters. • The DASY4 system with an Isotropic E-Field Probe EX3DV3 was used for the measurements. • The dipole was mounted on the small tripod so that the dipole feed point was positioned below the center marking of the flat phantom section and the dipole was oriented parallel to the body axis (the long side of the phantom). The standard measuring distance was 10 mm (above 1 GHz) and 15 mm (below 1 GHz) from dipole center to the simulating liquid surface. • The coarse grid with a grid spacing of 15 mm was aligned with the dipole. For 5 GHz band - The coarse grid with a grid spacing of 10 mm was aligned with the dipole. • Special 7x7x7 fine cube was chosen for cube • Distance between probe sensors and phantom surface was set to 3 mm. For 5 GHz band - Distance between probe sensors and phantom surface was set to 2.5 mm • The dipole input power (forward power) was 100 mW • The results are normalized to 1 W input power. Reference SAR Values for HEAD & BODY-tissue from calibration certificate of SPEAG. System Cal. SAR Avg (mW/g) Cal. certificate # validation dipole due date Tissue: Head Body D2450V2 D2450V2-706_Apr10 4/18/13 SAR1g: 51.6 52.4 SAR10g: 24.4 24.5 10.1. SYSTEM CHECK RESULTS FOR D2450V2 Ambient Temperature = 24°C; Relative humidity = 41% Measured by: Devin Chang System Measured (Normalized to 1 W) Tolerance Date Tested Target Delta (%) validation dipole Tissue: Body (%) SAR1g: 51.7 52.4 -1.34 D2450V2 07/08/10 ±10 SAR10g: 24.2 24.5 -1.22 Page 13 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

sto Datertime: 7zoto 1021.38am Test Laberetoy: Complance Contfcaton Sonvces System Performance Check — D2450V2 DUT. Dpole Type Dadsov2, Seral 705 Communiation System: System Check Signal— CW,Frequency 2450 Mz Duy Cycle: 111 Medum parametars used.(= 2450 Mc o =2 mhoim. 1, 527. p= 1000 katn® Pranion secton: Flt Sectin Reom Antient Temperature. 240 deg. ; Liqué Temperatre 230 deg. C DASY4 Confguraton — Area Scan seting— Find Seconday Maximum Witin. 20 08 and wih a peak SAR value greatethan 00012Wke —rrose exsove—snssat; Connrr 0, 7 587 89) Calorares 2zsiz0r0 — SensorSuface omm (Mechanical Suace Detecion) — Eectonies: DAE3 Sn500 Caltvated 9152000 —Pnantor: Fat Pravion ELi#O,Tyse GOOVAOOtEASeral 5N oo3 —Meassrement SW DASY4, V47 Buid 0. Poslrocessng SW SENCAD, V Buid tos d=10mm, Pin=100mW!Area Scan (7X7x1): Measurement grd. t1Smm. dy=1Smm Maximum valueof SAR (measured) = 609 mio d=10mm, Pin=100mW!Zoom Scan (7x7x7)/Cube 0: Measwrement gid —Smm, dy—5mm.de=Smm Refernce Value = 591 Vim, Power Drt =—0.153 aB Beak SAR (extrepoted) 104 Wig SaRtt gl= 5.17 mig: SaR(10 o ar milly Maximum vaiueof SA(measurea 674 mWig mi¥ds 606 225 130 n.ous — ces — — — rore — — — v. 2080 Hars rogrun wiree rien vn ropowavie unvige m rary n uw minwn uepnunar ue cane

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 SYSTEM CHECK – Z Plot Page 15 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 11. OUTPUT POWER VERIFICATION 11.1. WIFI RF OUTPUT POWER 8 02 .1 1b Co nd ucted Avg Pow er Ch an ne l # Freq . (MH z) (d Bm) (mW ) 1 24 12 16 .8 4 7.9 6 24 37 16 .9 4 8.8 11 24 62 16 .8 4 7.9 8 02 .1 1g 1 24 12 14 .6 2 8.8 6 24 37 16 .7 4 6.8 11 24 62 14 .6 2 8.8 8 02 .1 1n HT 20 1 24 12 13 .8 2 4.0 6 24 37 16 .6 4 5.7 11 24 62 13 .7 2 3.4 Note: KDB 248227 - SAR is not required for 802.11g/HT20 channels when the maximum average output power is less than 1/4 dB higher than that measured on the corresponding 802.11b channels. 11.2. BLUETOOTH RF OUTPUT POWER Blue too th C o nd ucted Avg Po we r Mod e Ch an ne l # Fre q. (MHz) (dBm ) (mW ) 0 240 2 10 .7 11 .7 G FSK 39 244 1 11 .2 13 .2 78 248 0 11 .5 14 .1 0 240 2 10 .0 10 .0 QPSK 39 244 1 10 .2 10 .5 78 248 0 10 .2 10 .5 0 240 2 7.9 6.2 8 PSK 39 244 1 8.2 6.6 78 248 0 8.1 6.5 Note: According to KDB 648474, Table 2, Unlicensed transmitters When there is no simultaneous transmission – (WiFi can not transmit simultaneously with Bluetooth) Output ≤ 60/f (25 mW): SAR is not required Output > 60/f (25 mW): stand-alone SAR required Page 16 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 12. SUMMARY OF TEST RESULTS Body SAR with 0 cm separation distance Test Freq. SAR (mW/g) Band Mode Ch No. position (MHz) 1-g 10-g 1 2412 1.110 0.351 Face up 6 2437 1.110 0.349 11 2462 1.010 0.314 2.4 GHz 802.11b w/ headset 6 2437 1.090 0.339 1 2412 Face down 6 2437 0.293 0.126 11 2462 Note: KDB 248227 - SAR is not required for 802.11g/HT20 channels when the maximum average output power is less than 1/4 dB higher than that measured on the corresponding 802.11b channels Page 17 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

o Datertime: mzoro rer—18 Pn Test Laborstoy: Complance Contfcaton Senvices WiFi_Body DUT: Apse. Type: NA Seriat NA Communieaton System: 802 1th, Frequency 2412 MzDuly Gyele 111 Medism perametars used (nterpolted) ( = 2412 Mitz = 1.94 mhaim , = 529. o = 1000 kyim? Prantom secion: Flt Secton Reom Ambent Temperature. 240 deg. ; Liqué Temperatre 230 deg. C DASY Contguraton — Area Scan seting — Find Seconday Maximum Witin. 20 48 end wih a peak SAR value greatethan 00012Wke —Prie ©aDVa— SNasst: Conv(750, 7 58 7.59) Calbraled 2222010 — SensorSurface amn (Mechanical Suace Detecion) — Eleconies DAE3 Sn500Caltvated 9152000 —Phanion Fat Phaniom ELi4O,Type GOOVAOOIEASera! SN 1oos —Meassrement SW DASY4, V47 Buld 0; Poslprocessng SW SENCAD, V Buid tos Face up_L—ch/Area Scan (Tx10x1): Measwemen:gis. de—tSnm,d=tonm Info Interlated mediur perametersused for SAR evaluaton Maximum valee of SAR (measured) = 1.08 miMig Face up_L—ch/Zoom Scan (7xTx8)/Cube 0: Measwementgis de—nmdy—Snm, cesmm Relerence Yalze 230 Vim, Power Di ho Sit textacoited=a 1 SARAIg)=1.11 mily: SAR(TO g) = 0351 mwly Info Inerpolated medur peramatersused for SAR evaluaton Maximum valee of SAR (measured) = 169 miMig ns 108 sos ues sase seis som mte 300

o0 Datertime: zrz0t0 11:17.22 AM Test Latorstoy: Compiance Cortfeaton Servces WiFi_Body DUT: Apple Type: NA Serat NA Communicaton System: 802 1to, Freguency. 2497 MitzDuty Cycle 1:1 Medum perameters used (nterpobted} 1# 2487 MKz, 0 = 1.98mham,£, = 528. o = 1000 kytm* Pranion secton: Flt Secton Reom Ambient Temperaure 24.0 deg. . Ligud Temperatire 230 deg. C DASY4 Confguraton —Area Scan seting — Find Secondary Maximum Wthin: 20 6B and wih a peak SAR value greatethan 0.0012Wikg —Brove Ex2DVa—SN26at; ConvF7 50 7.58,7.50) Calirated 2222010 — SensorSurace amm (Mechanical Surface Dotecton) — Elecvonics DAE3 $n00, Caitrates 162000 — Phanton: Ft Praniom ELIO, Tyoe CDOVACOBASenat on to0s "Measroment SW DASV4 VA7 Buid 60Posiprocesang SW SENCAD, V Buid tos Face up_M—ch/Area Scan (7x10i1): Measurementaid sx=tSmm, dy=tSnm lnfo: Interpdlated medium perametes used forSARevavaton Maximum vaiue of SAR (measired) = 0900 mWg Face up_M—ch/Zoom Scan (7x7x9)/Gube 0: Messwrement i se=Smm,dy—Smm, desanm Reternce Vakue 225 Vim; PowerDrit= 0.16r d Peas SAR (extrapobted) = 11 Wing SARIT g) = 111 milySAR(TO g) = 0.349 mhlg Info Inlerpolated medum perameters used forSARevavaton Maximum vaiee of SAR (measired) = 166 miWig mW 0.500 n.0 vau n2m act00 nom mt l.0.... Jose

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 Worst-case BODY Z-axis Page 20 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.

o Datertime: mB2ot0 15850 PM Tort Labortary: Compliance Cortieaton Sonices WiFi_Body DUT: Aoole Type: NA Seral NA Communicaton System: 802 118. Frequency 2462 HeDutyCycle 11 Medum parameters used (rtorolated) f = 2482 Mitz 0 =20" mhoim ¢,= 527 o = 1000 kyim? Pranion secton Fat Secton Rom Antient Temperatire. 240 deg.C; Lqué Temperatre 230 deg. C DASY4 Contguaton —Area Scan stt—Find Secondary Maximum Witin. 20 08 and wih a peak SAR value greatethan 0O01Wkg —Prove Ex30va shsot, Comne(7 Sb 7 58 7.59) Calivaled 2232010 — SensorSuface anm (Mecharica Surtace Detecton) — Elecvonics DAE Sn5oo. Caiivated 91152000 «Phantom, Flat PhantoELi 0 Type: QDOVADDIBASeral 5N 1008 —Meassrenent SW DASY4, V‘7 Buid 80, Poslprocessng SW SEMCAD, V1 8 Buld tos Face up_H—ch/Area Scan (7x10x1): Measurement gid de=1Smm, dy=19mm lnfo: Interpdated medium parameters used for SAR evalvaton Maximum vaveof SAR (measired)=1.03 miMig Face up_H—ch/Zoom Scan (Tx7x8)/Gube 0: Massrementgid e=Smm, dy—nm. decamn Reternce Valse = 227 Vim: Power Dt =—0.127dB Peak SAR iextacoited= 272 ¥ihoa SARIT 9) 101 mhig; SARTO g) = 0314 mwtly Info Inlerpobted median paramoters used for SAR evaluaton Maximum vaveof SAR (measired 1.58 miMig mivhe 0.500 o.«00 ucsuo nza oazo nom mte 300

10 nawernine zimoro s o 25 ow TestLaboratoy: Complance Contfcaton Sanvices WiFi_Body DUT Apple Type: NA Seriat NA Communication System: 80211b Frequengy: 2137WeDuty Cyole 1:1 Medum parametarsused (nterpolted) ( = 2497 MHz: o 1.98 mhaim, , 528. o = 1000 k/ Prarto secton:Flt Secton Reon Anbient Temperature. 240 deg. ; LidTemperatre 230 deg. C DASY4 Confouraton —Ares Scan seting — ind Seconday Maximum Wittin 20 40 and wih a gesk SAvalue greatethan 00012 —Broue Ex2DVa— SNaS3t: Conv£(750, 750. 7 S8)Calbvaled 2222010 — SemsorBurface amn (Mechancal Suface Detecion) — Eectronics DAE3 Sn500 Caltvated 9192000 ~Phanan: Fat Phaniom ELi4O,Type GOOVACOTBASerat SN 1oos —Meassrement SW DASY4, V47 Build 80 Postrocessng SW SENCAD, V Buid tos Face up_M—ch wiheadset/Area Scan (Tx10x1): Measwement gre. t= Srm 6=18mm InInterpoiated medium parametersused o SAR avaluaton Maxmum vaiueof SAR (measured) = 102 mW Face up_M—ch w/headset/Zoom Scan (7xTx$)/Cuibe 0: Meas.rement grs de=Snm, cy=Smm, ge:3nm Reference Valve = 22. Vim, Power Drit =—0.202 4B Peat SAR (exrapolted) 299 Wig SAR(T g) = 1.08 mivly: SaR(10 g)= 0339 mug Ino Inlerpolated mediur perametersused for SAR avaiuaton Maxmumvaiueof SAR (measured) = 165 nWg mds 8.700 aseo vaed s.20o aaa nom SE mm n zse

»0 Dateftime: 72010 11 a1:10 a Test Laborstoy: Complance Contfcaton Senvices WiFi_Body DUT: Apple Type: NA Seriat NA Communicaton System: 802 1th Frequency 2437 MHeDuty Cyole 111 Medur porametarsused (nterpolted) ( = 2427 Mz o = 1.98 mhaim, , = 528. o = 1000 kyim? Pranion secton: Flt Secton Reom Ambient Temperature 240 deg. ; Liqué Temperatre 230 deg. C DASY4 Confguraton — Area Scan seting — Find Seconday Maximum Witin. 20 48 and wih a peak SAR value greatethan 0O012Who —Brove Ex2DVa— SNaS3t: Conv£(750, 7 58 7.59) Calbvaled 2222010 — SensorSurace amn (Mechanical Suace Detecion) — Elecvonics DAE3 Sn500Caltvated 9152000 —Pnantom: Fat Ehanion ELi4O,Tyse GDOVAOOIEASerat SN 0s —Meassrement SW DASY4, V47 Buid 80 Poslprocessng SW SENCAD, V Buid tos Face down_M—ch/Area Scan (x10X1): Measwement gi. dc=19nm, oy=tonm Into Interpolated medium parametersusedfor SAR ovalvaton Maximum vaiee of SAR (measured)= 0321 mWig Face down_M—ch/Zoom Scan (7xTx$)/Cube 0: Measwrement is dxznm dy=Smm, de—smim Reternce Valus 127 Vim, Power Drit = 0140 0B Peak SAR (extrapoited) 0655 Wig SAR(T 9 = 0283 mily:SAR(TO g = 0.128 mly Info Interpolated mediur parametersused for SAR evaivaton Maximum valueof SAR (measured) = 0391 mWig m 8321 nosr nass naze noue nom mte sso

REPORT NO: 10U13294-16C DATE: August 27, 2010 FCC ID: BCG-E2407 IC: 579C-E2407 14. ATTACHMENTS No. Contents No. of page (s) 1 Certificate of E-Field Probe - EX3DV3 SN 3531 11 2 Certificate of System Validation Dipole - D2450 SN:706 9 Page 24 of 28 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS.


Document Created: 2010-08-27 17:11:37
Document Modified: 2010-08-27 17:11:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC