05 Short-Term Confidential_User Manual

FCC ID: AK8XAVAX150

Users Manual

Download: PDF
FCCID_4175758

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Cover XAVAX3000UC\010COV.fm 010COV.book Page 1 Tuesday, June 5, 2018 9:32 AM 4-739-317-1(1) AV RECEIVER Operating Instructions GB Mode d’emploi FR Manual de instrucciones ES Owner’s Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XAV-AX Serial No. To cancel the demonstration (Demo) display, see page 16. For the connection/installation, see page 26. Pour annuler l’affichage de démonstration (Démo), reportez- vous à la page 17. Pour le raccordement/l’installation, reportez-vous à la page 28. Para cancelar la pantalla de demostración (Demostración), consulte la página 17. Para la conexión/instalación, consulte la página 27. XAV-AX :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\020INT.fm 010COV.book Page 2 Tuesday, June 5, 2018 9:32 AM For safety, be sure to install this unit in the This device complies with part 15 of FCC Rules and dashboard of the car as the rear side of the unit Innovation, Science and Economic Development becomes hot during use. Canada’s licence-exempt RSSs. Operation is subject For details, see “Connection/Installation” to the following two conditions: (page 26). (1) this device may not cause harmful interference, and (2) this device must accept any interference The nameplate indicating operating voltage, etc., is received, including interference that may cause located on the bottom of the chassis. undesired operation. The validity of the CE marking is restricted to only This transmitter must not be co-located or operated those countries where it is legally enforced, mainly in conjunction with any other antenna or in the countries EEA (European Economic Area) and transmitter. Switzerland. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a Warning type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce To prevent fire or shock hazard, do not potential radio interference to other users, the expose the unit to rain or moisture. antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) To avoid electrical shock, do not open the is not more than that necessary for successful cabinet. Refer servicing to qualified personnel communication. only. This equipment complies with FCC/ISED radiation FOR THE CUSTOMERS IN THE USA. NOT exposure limits set forth for an uncontrolled APPLICABLE IN CANADA, INCLUDING IN THE environment and meets the FCC radio frequency PROVINCE OF QUEBEC. (RF) Exposure Guidelines and RSS-102 of the ISED POUR LES CLIENTS AUX ÉTATS-UNIS. NON radio frequency (RF) Exposure rules as this APPLICABLE AU CANADA, Y COMPRIS LA equipment has very low levels of RF energy. PROVINCE DE QUÉBEC. This equipment has been tested and found to comply with the limits for a Class B digital device, If you have any questions about this product: pursuant to Part 15 of the FCC Rules. These limits Visit: www.sony.com/ECTsupport are designed to provide reasonable protection Contact: Sony Customer Information Service Center against harmful interference in a residential at 1-800-222-7669 installation. This equipment generates, uses, and Write: Sony Customer Information Service Center can radiate radio frequency energy and, if not 12451 Gateway Blvd., Fort Myers, FL 33913 Supplier’s installed and used in accordance with the Declaration of Conformity instructions, may cause harmful interference to Trade Name: SONY radio communications. However, there is no Model: XAV-AX guarantee that interference will not occur in a Responsible Party: Sony Electronics Inc. particular installation. If this equipment does Address: 16535 Via Esprillo, San Diego, CA 92127 cause harmful interference to radio or television U.S.A. reception, which can be determined by turning Telephone Number: 858-942-2230 the equipment off and on, the user is This device complies with part 15 of the FCC rules. encouraged to try to correct the interference by Operation is subject to the following two one or more of the following measures: conditions: – Reorient or relocate the receiving antenna. (1) This device may not cause harmful interference, – Increase the separation between the and equipment and receiver. (2) this device must accept any interference – Connect the equipment into an outlet on a received, circuit different from that to which the receiver including interference that may cause undesired is connected. operation. – Consult the dealer or an experienced radio/TV technician for help. For the State of California, USA only Perchlorate Material – special handling may apply, You are cautioned that any changes or See modifications not expressly approved in this www.dtsc.ca.gov/hazardouswaste/perchlorate manual could void your authority to operate this equipment. 2GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\020INT.fm 010COV.book Page 3 Tuesday, June 5, 2018 9:32 AM WARNING: Do not ingest battery, On BLUETOOTH communication Chemical Burn Hazard. • Microwaves emitting from a BLUETOOTH device The remote commander contains a coin/ may affect the operation of electronic medical button cell battery. If the coin/button cell battery is devices. Turn off this unit and other BLUETOOTH swallowed, it can cause severe internal burns in just devices in the following locations, as it may cause 2 hours and can lead to death. an accident. Keep new and used batteries away from children. If – where inflammable gas is present, in a hospital, the battery compartment does not close securely, train, airplane, or petrol station stop using the product and keep it away from – near automatic doors or a fire alarm children. • This unit supports security capabilities that If you think batteries might have been swallowed or comply with the BLUETOOTH standard to provide placed inside any part of the body, seek immediate a secure connection when the BLUETOOTH medical attention. wireless technology is used, but security may not be enough depending on the setting. Be careful Note on the lithium battery when communicating using BLUETOOTH wireless Do not expose the battery to excessive heat such as technology. direct sunlight, fire or the like. • We do not take any responsibility for the leakage of information during BLUETOOTH Warning if your car’s ignition has no ACC communication. position Do not install this unit in a car that has no ACC If you have any questions or problems concerning position. The display of the unit does not turn off your unit that are not covered in this manual, even after turning the ignition off, and this consult your nearest Sony dealer. causes battery drain. Disclaimer regarding services offered by third parties Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations. Important notice Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE. Dear customer, this product includes a radio transmitter. Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle. Emergency calls This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies). 3GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\030TOC.fm 010COV.book Page 4 Tuesday, June 5, 2018 9:32 AM Table of Contents Connection/Installation Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Parts List for Installation . . . . . . . . . . . . . . . . . . . . 26 Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . 5 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Getting Started Performing Initial Settings . . . . . . . . . . . . . . . . . . . . 8 Preparing a BLUETOOTH Device. . . . . . . . . . . . . . . . 8 Connecting Rear View Camera . . . . . . . . . . . . . . . . 9 Listening to the Radio Listening to the Radio. . . . . . . . . . . . . . . . . . . . . . . . 9 Using Tuner Option Functions . . . . . . . . . . . . . . . . 10 Playback Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . 12 Playing a BLUETOOTH Device. . . . . . . . . . . . . . . . . 12 Searching and Playing Tracks. . . . . . . . . . . . . . . . . 12 Other Settings During Playback. . . . . . . . . . . . . . . 13 Handsfree Calling Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Available Operations During a Call . . . . . . . . . . . . 14 Useful Functions Apple CarPlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Android Auto™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Using Gesture Command . . . . . . . . . . . . . . . . . . . . 16 Settings Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . 16 General Settings (General) . . . . . . . . . . . . . . . . . . . 16 Sound Settings (Sound) . . . . . . . . . . . . . . . . . . . . . 17 Visual Settings (Visual) . . . . . . . . . . . . . . . . . . . . . . 18 BLUETOOTH Settings (Bluetooth). . . . . . . . . . . . . . 18 Additional Information Updating the Firmware. . . . . . . . . . . . . . . . . . . . . . 18 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 5 Tuesday, June 5, 2018 9:32 AM Guide to Parts and Controls Main unit The VOL (volume) + button has a tactile dot. ȭ Ã/Ñ (previous/next) – Move to the previous/next item. ȩ Display/touch panel – Press and hold to fast-reverse/fast-forward. Ȫ HOME Ȯ OPTION Open the HOME menu. Open the OPTION screen (page 7). ATT (attenuate) VOICE Press and hold for 1 second to attenuate the Press and hold to activate the voice command sound. function for Apple CarPlay and Android Auto. To cancel, press and hold again, or press VOL +. ȫ VOL (volume) +/– Ȭ Receptor for the remote commander 5GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 6 Tuesday, June 5, 2018 9:32 AM ȶ R/a/{/C RM-X170 remote commander Functions differ depending on the selected source. The remote commander can be used to operate the – Tuner: select a preset station or tune into a audio controls. For menu operations, use the touch station automatically. panel. – USB: select a folder or move to the previous/next file. ENTER Enter the selected item. ȷ SRC (source) Change the source. Each time you press this button, a selectable source is displayed in a popup on the current display. ȸ MODE Select the radio band. Remove the insulation film before use. Note The white buttons in the illustration above are not supported. ȯ OFF Turn the source off. Ȱ MONITOR OFF Turn off the monitor. To turn back on, press again. ȱ EQ (equalizer) Select an equalizer curve. Ȳ Number buttons (0 – 9) ȳ CLEAR ̟ ā (play/pause) ȵ Ã/Ñ (previous/next) ù/ß (fast-reverse/fast-forward) 6GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 7 Tuesday, June 5, 2018 9:32 AM Ǵ Status indication Screen displays Lights up when the sound is attenuated. Playback screen: Lights up when the audio device is playable by enabling the A2DP (Advanced Audio Distribution Profile). Lights up when handsfree calling is available by enabling the HFP (Handsfree Profile). Indicates the signal strength status of the connected cellular phone. Indicates the remaining battery status of the connected cellular phone. Lights up when the Bluetooth® signal is on. Flashes when the connection is in progress. HOME screen: ǵ (source option) Open the source option menu. The available items differ depending on the source. Ƕ Application specific area Display playback controls/indications or show the unit’s status. Displayed items differ depending on the source. Ƿ Clock (page 16) Ǹ (return to the playback screen) Switch from the HOME screen to the playback screen. ǹ Sources and Settings select keys OPTION screen: Change the source or make various settings. Display the setting icon and other icons by swiping the bottom of this area right or left. ˱ Sources select keys Change the source. ˲ (EXTRA BASS) Change the EXTRA BASS setting (page 17). ˳ (EQ10/Subwoofer) Change the EQ10/Subwoofer setting (page 17). ˴ (monitor off) Turn off the monitor. When the monitor is turned off, touch any part of the display to turn it back on. 7GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 8 Tuesday, June 5, 2018 9:32 AM 1 Place the BLUETOOTH device within 1 m (3 ft) of this unit. Getting Started 2 Press HOME, then touch [Settings]. 3 Touch [Bluetooth]. Performing Initial Settings 4 Touch [Bluetooth Connection], then set the You need to perform initial settings before signal to [ON]. operating the unit for the first time, after replacing The BLUETOOTH signal is turned on and lights the car battery, or changing connections. up on the status bar of the unit. If the initial settings screen does not appear when you turn on the unit, perform the factory reset 5 Touch [Pairing]. (page 17) to initialize the unit. flashes while the unit is in pairing standby mode. 1 Touch [Language], then set the display language. 6 Perform pairing on the BLUETOOTH device so it detects this unit. 2 Touch [Demo] repeatedly to select [OFF] to disable the demonstration mode. 7 Select [XAV-AX0] shown in the display of the BLUETOOTH device. 3 Touch [Set Date/Time], then set the date If your model name does not appear, repeat and time. from step 5. 4 After setting the date and time, touch [OK]. 5 To return to the previous display, touch , then touch [OK].  The startup caution appears. 6 Read through the startup caution, then if you accept all conditions, touch [Close]. The setting is complete. 8 If passkey* input is required on the This setting can be further configured in the setting BLUETOOTH device, input [0000]. menu (page 16). * Passkey may be called “passcode,” “PIN code,” “PIN number,” “password,” etc., depending on the BLUETOOTH device. Preparing a BLUETOOTH Device You can enjoy music or perform handsfree calling Input passkey depending on the BLUETOOTH compatible device such as smartphones, cellular phones, and audio [0000] devices (hereafter “BLUETOOTH device” if not otherwise specified). For details on connecting, refer to the operating instructions supplied with the When pairing is made, stays lit. device. Before connecting the device, turn down the 9 Select this unit on the BLUETOOTH device to volume of this unit; otherwise, a loud sound may establish the BLUETOOTH connection. result. or lights up when the connection is made. Notes • The unit can only be connected with one BLUETOOTH Pairing and connecting with a device at a time. • To disconnect the BLUETOOTH connection, turn the BLUETOOTH device connection off from either the unit or the BLUETOOTH device. When connecting a BLUETOOTH device for the first • BLUETOOTH pairing is not possible while Apple CarPlay or time, mutual registration (called “pairing”) is Android Auto is running. required. Pairing enables this unit and other devices to recognize each other. 8GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 9 Tuesday, June 5, 2018 9:32 AM Connecting with a paired BLUETOOTH device Listening to the Radio To use a paired device, connection with this unit is required. Some paired devices will connect Listening to the Radio automatically. To listen to the radio, press HOME then touch [Tuner]. Reception controls/indications 1 Press HOME, then touch [Settings]. 2 Touch [Bluetooth]. 3 Touch [Bluetooth Connection], then touch [ON]. Make sure that lights up on the status bar of the unit. 4 Activate the BLUETOOTH function on the BLUETOOTH device. 5 Operate the BLUETOOTH device to connect to this unit. or lights up on the status bar. ɸ Current band Change the band (FM1, FM2, FM3, AM1 or AM2). To connect the last-connected device from this unit ɹ Current frequency, program service name*, RDS (Radio Data System) indication* When the ignition is turned to on with the BLUETOOTH signal activated, this unit searches for * During RDS reception. the last-connected BLUETOOTH device, and ɺ (tuner option) connection is made automatically. Open the tuner option menu. Note ɻ SEEK-/SEEK+ While streaming BLUETOOTH audio, you cannot connect from this unit to the cellular phone. Connect from the Tune in automatically. cellular phone to this unit instead. ɼ / To install the microphone Tune in manually. For details, see “Installing the microphone” Touch and hold to continuously skip (page 28). frequencies. ɽ Preset numbers Select a preset station. Swipe right/left to show Connecting Rear View Camera the other preset stations. Touch and hold to store the current frequency in By connecting the optional rear view camera to the that preset. CAMERA IN terminal, you can display the picture from the rear view camera. For details, see “Connection/Installation” (page 26). Tuning To display the picture from the rear view 1 Select the desired band (FM1, FM2, FM3, camera AM1 or AM2). Press HOME, touch [Rear Camera]. 2 Perform tuning. To tune automatically Touch SEEK-/SEEK+. Scanning stops when the unit receives a station. To tune manually Touch and hold / to locate the approximate frequency, then touch / repeatedly to finely adjust to the desired frequency. 9GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 10 Tuesday, June 5, 2018 9:32 AM Storing manually 1 While receiving the station that you want to Playback store, touch and hold the desired preset number. Playing a USB Device MSC (Mass Storage Class) type USB devices* Receiving stored stations compliant with the USB standard can be used. 1 Select the band, then touch the desired * e.g., a USB flash drive, digital media player, Android™ phone preset number. Notes • USB devices formatted with file systems FAT12/16/32/ exFAT are supported. Using Tuner Option Functions • For details on the compatibility of your USB device, visit the support site on the back cover. The following functions are available by touching • For details on the supported file formats, see “Supported formats for USB playback” (page 19). . 1 Turn down the volume on the unit. BTM (Best Tuning Memory) Stores stations in order of frequency on the 2 Connect the USB device to the USB port. preset numbers. 18 stations can be stored for FM 3 Press HOME, then touch [USB]. and 12 stations for AM as preset stations. Playback starts. PTY* To remove the device Select a program type from the PTY list to search Turn the unit off or turn the ignition switch to the for a station broadcasting the selected program ACC off position, then remove the USB device. type. * Only available during FM reception. Playing a BLUETOOTH Device You can play contents on a connected device that supports BLUETOOTH A2DP (Advanced Audio Distribution Profile). 1 Make a BLUETOOTH connection with the audio device (page 8). 2 Press HOME, then touch [BT Audio]. 3 Operate the audio device to start playback. Notes • Depending on the audio device, information such as title, track number/time, and playback status may not be displayed on this unit. • Even if the source is changed on this unit, playback of the audio device does not stop. • BLUETOOTH pairing is not possible while Apple CarPlay is running. To match the volume level of the BLUETOOTH device to other sources You can reduce the volume level differences between this unit and the BLUETOOTH device: During playback, touch , then set [Input Level] between –6 and +6. 10GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 11 Tuesday, June 5, 2018 9:32 AM Searching and Playing Tracks Other Settings During Playback Further settings are available in each source by touching . The available items differ depending Repeat play and shuffle play on the source. 1 During playback, touch (repeat) or Picture EQ (shuffle) repeatedly until the desired play Adjusts the picture quality according to your mode appears. taste: [Dynamic], [Standard], [Theater], [Custom]. Playback in the selected play mode may take (Available only when the parking brake is applied time to start. and USB video is selected.) Available play modes differ depending on the Aspect selected sound source and connected device. Selects an aspect ratio for the screen of the unit. (Available only when the parking brake is applied and USB video is selected.) Searching for a file from the list screen Normal 1 During USB playback, touch . Displays a 4:3 picture in its original size, with side The list screen from the currently played item bars to fill the 16:9 screen. appears. Zoom Displays a 16:9 picture that has been converted into 4:3 letter box format. Full Displays a 16:9 picture in its original size. Captions Enlarges the picture horizontally, while fitting captions in the screen. Furthermore, touch (audio) or (video) to list up by file type. 2 Touch the desired item. Playback starts. 11GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 12 Tuesday, June 5, 2018 9:32 AM ɺ (phonebook)* Select a contact from the name list/number Handsfree Calling list in the phonebook. To search for the desired contact in alphabetical order from To use a cellular phone, connect it with this unit. For the name list, touch . details, see “Preparing a BLUETOOTH Device” ɻ (phone number input) (page 8). Enter the phone number. ɼ Preset phone number list Select the stored contact. To store the contact, see “Presetting phone numbers” (page 14). * The cellular phone needs to support PBAP (Phone Book Access Profile). Note The handsfree calling functions explained below are 3 Touch . available only when the Apple CarPlay or Android Auto The phone call starts. function is deactivated. When the Apple CarPlay or Android Auto function is activated, use the handsfree calling functions on its application. Presetting phone numbers You can store up to 6 contacts in the preset list. Receiving a Call 1 In the phone screen, select a phone number that you want to store in the preset dial 1 Touch when a call is received. from the phonebook. The phone call starts. The confirmation display appears. Note 2 Touch [Add to Preset]. The ringtone and talker’s voice are output only from the front speakers. 3 Select the preset phone number list where the phone number is stored. To reject/end a call The contact is stored in the preset phone Touch . number list. Making a Call 1 Press HOME, then touch [Phone]. 2 Touch one of the call icons on the BLUETOOTH phone display. ɸ (call history)* Select a contact from the call history list. The unit stores the last 20 calls. ɹ (redial) Make a call automatically to the last contact you made. 12GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 13 Tuesday, June 5, 2018 9:32 AM Available Operations During a Useful Functions Call To adjust the ringtone volume Apple CarPlay Press VOL +/– while receiving a call. Apple CarPlay lets you use your iPhone in the car in To adjust the talker’s voice volume a way that allows you to stay focused on the road. Press VOL +/– during a call. (Available only when your iPhone is connected to the USB port.) To adjust the volume for the other party (Mic gain adjustment) Notes on using Apple CarPlay During a handsfree call, touch , then set • iPhone with iOS 7.1 or later is required. Update to [MIC Gain] to [High], [Middle], or [Low]. the latest iOS version before use. • Apple CarPlay can be used on iPhone 5 or later. To reduce echo and noise (Echo/noise • For details on compatible models, refer to the canceler mode) compatibility list on the support site on the back During a call, touch , then set [Speech Quality] to cover. [Mode 1] or [Mode 2]. • For details about Apple CarPlay, refer to the manual supplied with your iPhone, or visit the To switch between handsfree mode and website of Apple CarPlay. handheld mode • Since the GPS on your iPhone is used, place your During a call, touch to switch the iPhone where it can easily receive a GPS signal. phone call audio between the unit and cellular phone. 1 Connect your iPhone to the USB port. To connect an iPhone, use a USB connection Note cable for iPhone (not supplied). Depending on the cellular phone, this operation may not be available. 2 Press HOME, then touch the Apple CarPlay icon. To answer an incoming call automatically Your iPhone’s display appears on the display of Touch , then set [Auto Answer] to [ON]. the unit. Touch and control the applications. Use of the Apple CarPlay logo means that a vehicle user interface meets Apple performance standards. Apple is not responsible for the operation of this vehicle or its compliance with safety and regulatory standards. Please note that the use of this product with iPhone may affect wireless performance. 13GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 14 Tuesday, June 5, 2018 9:32 AM Android Auto™ Using Gesture Command Android Auto extends the Android platform into the You can perform frequently-used operations by car in a way that’s purpose-built for driving. swiping your finger on the reception/playback (Available only when your Android phone is display. connected to the USB port.) Note The gesture commands explained below are not available Notes on using Android Auto on the screens of Apple CarPlay and Android Auto. • Android phone with Android 5.0 or higher is required. Update to the latest OS version before Do this To use. • Your Android phone needs to support Android Radio reception: seek forward stations. Auto. For details on compatible models, refer to (The same as pressing and the compatibility list on the support site on the Swipe left to right holding Ñ.) back cover. • Download the Android Auto application on Video/audio playback: Google Play. skip forward a file/track. • For details about Android Auto, refer to the (The same as Ñ.) manual supplied with your Android phone, or visit the website of Android Auto. Radio reception: seek backward stations. • Since the GPS on your Android phone is used, (The same as pressing and place your Android phone where it can easily Swipe right to left holding Ã.) receive a GPS signal. • Android Auto may not be available in your country Video/audio playback: or region. skip backward a file/track. (The same as Ã.) 1 Connect your Android phone to the USB port. To connect an Android phone, use an Radio reception: appropriate connection cable (not supplied). receive stored stations (go forward). 2 Press HOME, then touch the Android Auto Swipe upwards icon. The Android Auto interface will be displayed full- Radio reception: screen on the display of the unit. Touch and receive stored stations control the applications. Swipe downwards (go backward). 14GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 15 Tuesday, June 5, 2018 9:32 AM Steering Control Selects the input mode for the connected remote Settings control. To prevent a malfunction, be sure to match the input mode with the connected Basic Setting Operation remote control before use. Custom You can set items in the following setup categories: Input mode for the steering wheel remote General Settings (General), Sound Settings (Sound), control (follow the procedures of [ ] to register Visual Settings (Visual), BLUETOOTH Settings functions on the connected remote control). (Bluetooth) Preset Input mode for the wired remote control 1 Press HOME, then touch [Settings]. excluding the steering wheel remote control. 2 Touch one of the setup category. The items that can be set differ depending on The steering button panel appears. the source and settings. ɞ Press and hold the button you want to assign to the steering wheel. 3 Move the scrollbar up and down to select The button on the panel lights up (standby). the desired item. ɟ Press and hold the button on the steering To return to the previous display wheel you want to assign the function to. Touch . The button on the panel will change the color (highlighted or encircled by an orange line). To switch to the playback screen ɠ To register other functions, repeat steps ɞ Touch . and ɟ. (Available only when [Steering Control] is set to [Custom].) General Settings (General) Notes • While making settings, the connected remote control cannot be used even though some functions have Language already been registered. Use the buttons on the unit. Selects the display language: [English], • If an error occurs while registering, all the registered [Español], [Français], [Deutsch], [Italiano], information is cleared. Restart registration from the [Português], [Русский], [ ], [ ], [ ], beginning. [ ], [ ]. • This function may not be available on some vehicles. For details on the compatibility of your vehicle, visit the support site on the back cover. Demo Activates the demonstration: [OFF], [ON]. Clock Time Sets the clock time by the RDS data: [OFF], [ON]. Date/Time Date Format Factory Reset Selects the format: [DD/MM/YY], [MM/DD/YY], Initializes all the settings to the factory settings. [YY/MM/DD]. Time Format Firmware Version Selects the format: [12-hour], [24-hour]. Updates and confirms the firmware version. Set Date/Time Sets the date and clock time manually. Open Source Licenses Displays the software licenses. Beep Activates the operation sound: [OFF], [ON]. Rear View Camera Selects the image from the rear view camera: [OFF], [Normal], [Reverse] (mirror image). [Guide Line Adjust] adjusts the guide on the picture from the rear view camera. Touch the near side ɸ or far side ɹ (red portions) of the guide to adjust. Touch / / / to adjust the guide position, and touch [ ] or [ ] to adjust the guide width. 15GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 16 Tuesday, June 5, 2018 9:32 AM Sound Settings (Sound) Visual Settings (Visual) EXTRA BASS Wallpaper Reinforces bass sound in synchronization with Changes the wallpaper by touching the desired the volume level: [OFF], [1], [2]. color. EQ10/Subwoofer Dimmer Selects an equalizer curve and adjusts the Dims the display: [OFF], [Auto], [ON]. subwoofer level. ([Auto] is available only when the illumination EQ10 control lead is connected and works when the Selects the equalizer curve: [OFF], [R&B], [Rock], head light is turned on.) [Pop], [Hip-Hop], [Dance], [EDM], [Jazz], [Soul], [ ] adjusts the brightness level when the [Country], [Custom]. dimmer is activated: –5 to +5. [Custom] adjusts the equalizer curve: –6 to +6. Subwoofer Touch Panel Adjust Adjusts the volume level of the subwoofer: Adjusts the touch panel calibration if the [OFF], –10 to +10. touching position does not correspond with the (Available when any source is selected.) proper item. Balance/Fader Adjusts the balance/fader level. Balance BLUETOOTH Settings (Bluetooth) Adjusts the sound balance between the left and right speakers: [L15] to [R15]. Bluetooth Connection Fader Activates the BLUETOOTH signal: [OFF], [ON], Adjusts the sound balance between the front [Pairing] (enters into pairing standby mode). and rear speakers: [Front 15] to [Rear 15]. Bluetooth Device Info Crossover Displays the information of the device connected Adjusts the cut-off frequency and subwoofer to the unit. phase. (Available only when [Bluetooth Connection] is High Pass Filter set to [ON] and a BLUETOOTH device is Selects the cut-off frequency of the front/rear connected to the unit.) speakers: [OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz]. Bluetooth Reset Low Pass Filter Initializes all BLUETOOTH-related settings such as Selects the cut-off frequency of the subwoofer: pairing information, call history, history of [OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz]. connected BLUETOOTH devices, etc. Subwoofer Phase Selects the subwoofer phase: [Normal], [Reverse]. DSO (Dynamic Stage Organizer) Enhances audio output: [OFF], [Low], [Middle], [High]. 16GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 17 Tuesday, June 5, 2018 9:32 AM Notes on LCD panel • Do not get the LCD panel wet or expose it to Additional Information liquids. This may cause a malfunction. Updating the Firmware To update the firmware, visit the support site on the back cover, then follow the online instructions. Note During the update, do not remove the USB device. Precautions • Power antenna (aerial) extends automatically. • Do not press down hard on the LCD panel as doing • When you transfer ownership or dispose of your so can distort the picture or cause a malfunction car with the unit installed, initialize all the settings (i.e., the picture may become unclear or the LCD to the factory settings by performing the factory panel may be damaged). reset (page 17). • Do not touch the panel with objects other than • Do not splash liquid onto the unit. with your finger as it may damage or break the LCD panel. Notes on safety • Clean the LCD panel with a dry soft cloth. Do not • Comply with your local traffic rules, laws, and use solvents such as benzine, thinner, regulations. commercially available cleaners, or antistatic spray. • While driving • Do not use the unit outside the temperature range – Do not watch or operate the unit, as it may lead 0 ºC – 40 ºC (32 ºF – 104 ºF). to distraction and cause an accident. Park your • If your car was parked in a cold or hot place, the car in a safe place to watch or operate the unit. picture may not be clear. However, the monitor is – Do not use the setup feature or any other not damaged and the picture will become clear function which could divert your attention from after the temperature in your car becomes normal. the road. • Some stationary blue, red, or green dots may – When backing up your car, be sure to look back appear on the monitor. These are called “bright and watch the surroundings carefully for your spots” and can happen with any LCD. The LCD safety even if the rear view camera is connected. panel is precision-manufactured with more than Do not depend on the rear view camera 99.99% of its segments functional. However, it is exclusively. possible that a small percentage (typically 0.01%) • While operating of the segments may not light up properly. This – Do not insert your hands, fingers, or foreign will not, however, interfere with your viewing. objects into the unit as it may cause injury or damage to the unit. Notes on the touch panel – Keep small articles out of the reach of children. • This unit uses a resistive touch panel. Touch the – Be sure to fasten seatbelts to avoid injury in the panel directly with your fingertip. event of sudden movement of the car. • Multi-touch operation is not supported on this unit. Preventing an accident • Do not touch the panel with sharp objects such as Pictures appear only after you park the car and a needle, pen, or fingernail. Operation with a set the parking brake. stylus is not supported on this unit. If the car starts moving during video playback, • Do not let any objects contact the touch panel. If the following caution is displayed and you the panel is touched by an object other than your cannot watch the video. fingertip, the unit may not respond correctly. • Since glass material is used for the panel, do not [Video blocked for your safety.] subject the unit to strong shock. If cracking or chipping occurs on the panel, do not touch the Do not operate the unit or watch the monitor damaged part as it may cause injury. while driving. • Keep other electrical devices away from the touch panel. They may cause the touch panel to malfunction. 17GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 18 Tuesday, June 5, 2018 9:32 AM Supported formats for USB playback About iPhone ˋ WMA (.wma)*1*2 • For details on compatible iPhone models, visit the support Bit rate: 48 kbps – 192 kbps (Supports variable bit site on the back cover. rate (VBR))*3 • Use of the Made for Apple badge means that an accessory Sampling frequency*4: 44.1 kHz has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified ˋ MP3 (.mp3)*1*2 by the developer to meet Apple performance standards. Bit rate: 48 kbps – 320 kbps (Supports variable Apple is not responsible for the operation of this device or bit rate (VBR))*3 its compliance with safety and regulatory standards. Sampling frequency*4: 32 kHz, 44.1 kHz, 48 kHz Please note that the use of this accessory with an Apple ˋ AAC (.m4a)*1*2 product may affect wireless performance. Bit rate: 40 kbps – 320 kbps (Supports variable bit rate (VBR))*3 Sampling frequency*4: 8 kHz – 48 kHz Notice on license Bit per sample (Quantization bit): 16 bits This product contains software that Sony uses under a ˋ FLAC (.flac)*1*6 licensing agreement with the owner of its copyright. We are Sampling frequency*4: 8 kHz – 48 kHz obligated to announce the contents of the agreement to Bit per sample (Quantization bit): 16 bits customers under requirement by the owner of copyright for the software. ˋ WAV (.wav)*1 For details on software licenses, see page17. Sampling frequency*4: 8 kHz – 48 kHz Bit per sample (Quantization bit): 16 bits, 24 bits Notice on GNU GPL/LGPL applied software This product contains software that is subject to the ˋ Xvid (.avi) following GNU General Public License (hereinafter referred Video codec: MPEG-4 Advanced Simple Profile to as “GPL”) or GNU Lesser General Public License Audio codec: MP3 (MPEG-1 Layer3) (hereinafter referred to as “LGPL”). These establish that Bit rate: Max. 4 Mbps customers have the right to acquire, modify, and Frame rate: Max. 30 fps (30p/60i) redistribute the source code of said software in accordance with the terms of the GPL or LGPL displayed on this unit. Resolution: Max. 1280 × 720*5 The source code for the above-listed software is available ˋ MPEG-4 (.mp4) on the Web. Video codec: MPEG-4 Advanced Simple Profile, To download, please access the following URL then select AVC Baseline Profile the model name “XAV-AX.” URL: http://www.sony.net/Products/Linux/ Audio codec: AAC Please note that Sony cannot answer or respond to any Bit rate: Max. 4 Mbps inquiries regarding the content of the source code. Frame rate: Max. 30 fps (30p/60i) Resolution: Max. 1280 × 720*5 If you have any questions or problems concerning your unit ˋ WMV (.wmv, .avi)*1 that are not covered in this Operating Instructions, consult your nearest Sony dealer. Video codec: WMV3, WVC1 Audio codec: MP3, WMA Bit rate: Max. 6 Mbps Frame rate: Max. 30 fps Maintenance Resolution: Max. 720 × 480*5 ˋ MKV (.mkv) Replacing the lithium battery (CR2025) of the Video codec: MPEG-4 Advanced Simple Profile, remote commander AVC Baseline Profile When the battery becomes weak, the range of the Audio codec: MP3, AAC remote commander becomes shorter. Bit rate: Max. 5 Mbps Frame rate: Max. 30 fps CAUTION Resolution: Max. 1280 × 720*5 Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent *1 Copyright-protected files and multi-channel audio files cannot be played back. type. *2 DRM (Digital Rights Management) files cannot be played Lithium battery (CR2025) back. + side up *3 Non-standard bit rates or non-guaranteed bit rates are included depending on the sampling frequency. *4 Sampling frequency may not correspond to all encoders. *5 These numbers indicate the maximum resolution of q playable video and do not indicate the player’s display resolution. The display resolution is 800 × 480. *6 Displaying the tag information is not supported. Note Note on the lithium battery Keep the lithium battery out of the reach of children. Should Some files may not be played back even though their file the battery be swallowed, immediately consult a doctor. formats are supported by the unit. 18GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 19 Tuesday, June 5, 2018 9:32 AM Specifications Compatible BLUETOOTH Profiles*2: A2DP (Advanced Audio Distribution Profile) 1.3 FOR THE CUSTOMERS IN THE USA. NOT AVRCP (Audio Video Remote Control Profile) 1.3 APPLICABLE IN CANADA, INCLUDING IN THE HFP (Handsfree Profile) 1.6 PROVINCE OF QUEBEC. PBAP (Phone Book Access Profile) 1.1 Corresponding codec: SBC, AAC POUR LES CLIENTS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA *1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a PROVINCE DE QUÉBEC. microwave oven, static electricity, reception sensitivity, antenna (aerial)’s performance, operating system, AUDIO POWER SPECIFICATIONS software application, etc. CTA2006 Standard *2 BLUETOOTH standard profiles indicate the purpose of Power Output: 20 Watts RMS × 4 at BLUETOOTH communication between devices. 4 Ohms < 1% THD+N SN Ratio: 80 dBA (reference: 1 Watt into Power amplifier section 4 Ohms) Outputs: Speaker outputs Speaker impedance: 4 Ω – 8 Ω Monitor section Maximum power output: 55 W × 4 (at 4 Ω) Display type: Wide LCD color monitor Dimensions: 6.95 in General System: TFT active matrix Power requirements: 12 V DC car battery Number of pixels: (negative ground (earth)) 1,152,000 pixels (800 × 3 (RGB) × 480) Rated current consumption: 10 A Color system: Dimensions: PAL/NTSC automatic select for CAMERA IN Approx. 178 mm × 100 mm × 139 mm terminal (7 1/8 in × 4 in × 5 1/2 in) (w/h/d) Mounting dimensions: Tuner section Approx. 182 mm × 111 mm × 120 mm (7 1/4 in × 4 3/8 in × 4 3/4 in) (w/h/d) FM Mass: Approx. 1.1 kg (2 lb 7 oz) Tuning range: 87.5 MHz – 107.9 MHz Package contents: Usable sensitivity: 7 dBf Main unit (1) Signal-to-noise ratio: 70 dB (mono) Parts for installation and connections (1 set) Separation at 1 kHz: 45 dB Remote Commander (1): RM-X170 AM Microphone (1) Tuning range: 530 kHz – 1,710 kHz Optional accessories/equipment: Sensitivity: 32 μV Cable for steering wheel remote input: RC- SR1 USB player section Ask the dealer for detailed information. Interface: USB (Hi-speed) Maximum current: 1.5 A Design and specifications are subject to change without notice. Wireless communication Communication System: BLUETOOTH Standard version 3.0 Copyrights Output: The Bluetooth® word mark and logos are registered BLUETOOTH Standard Power Class 2 trademarks owned by the Bluetooth SIG, Inc. and any use (Max. +4 dBm) of such marks by Sony Corporation is under license. Other Maximum communication range*1: trademarks and trade names are those of their respective Line of sight approx. 10 m (33 ft) owners. Frequency band: 2.4 GHz band (2.4000 GHz – 2.4835 GHz) Modulation method: FHSS 19GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 20 Tuesday, June 5, 2018 9:32 AM Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. Troubleshooting The following checklist will help you remedy This product is protected by certain intellectual property problems you may encounter with your unit. rights of Microsoft Corporation. Use or distribution of such Before going through the checklist below, check technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary. the connection and operating procedures. For details on using the fuse and removing the unit Apple, iPhone, and Lightning are trademarks of Apple Inc., from the dashboard, see “Connection/Installation” registered in the U.S. and other countries. (page 26). Apple CarPlay is a trademark of Apple Inc. If the problem is not solved, visit the support site on IOS is a trademark or registered trademark of Cisco in the the back cover. U.S. and other countries and is used under license. Android, Android Auto, Google and Google Play are General trademarks of Google LLC. There is no beep sound. THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL q An optional power amplifier is connected and PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON- you are not using the built-in amplifier. COMMERCIAL USE OF A CONSUMER FOR DECODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”) THAT WAS ENCODED BY A CONSUMER The fuse has blown. ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY The unit makes noise when the position of the AND/OR WAS OBTAINED FROM A VIDEO PROVIDER ignition is switched. LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. q The leads are not matched correctly with the car’s NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY accessory power connector. OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND The display disappears from/does not appear on LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE the monitor. HTTP://WWW.MPEGLA.COM q The monitor off function is activated (page 6, 7). THIS PRODUCT IS LICENSED UNDER THE AVC PATENT – Touch anywhere on the display to turn the PORTFOLIO LICENSE FOR THE PERSONAL AND NON- display back on. COMMERCIAL USE OF A CONSUMER TO (i)ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD Menu items cannot be selected. (“AVC VIDEO”) q Unavailable menu items are displayed in gray. AND/OR (ii)DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND The USB functions do not work properly. NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM q Do not use a USB extension cable as it may cause A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO deterioration of signal quality. LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER – Use a shorter USB cable when connecting the USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE USB device, or replace the USB cable with a new HTTP://WWW.MPEGLA.COM one. THIS PRODUCT IS LICENSED UNDER THE AVC PATENT The unit cannot be operated. PORTFOLIO LICENSE AND VC-1 PATENT PORTFOLIO LICENSE q Press and hold HOME for more than 10 seconds FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER TO DECODE VIDEO IN COMPLIANCE WITH THE to restart the unit. For your safety, do not restart AVC STANDARD (“AVC VIDEO”) AND/OR THE VC-1 STANDARD the unit while you are driving. (“VC-1 VIDEO”) THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER Touch panel operation LICENSED TO PROVIDE AVC VIDEO AND/OR VC-1 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER The touch panel does not react to your touch USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM correctly. MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM q Touch one part of the touch panel at a time. If All other trademarks are trademarks of their respective two or more parts are touched simultaneously, owners. the touch panel will not react correctly. q Calibrate the touch panel of the display (page 18). q Touch the pressure sensitive panel firmly. Multi-touch is not recognized. q Multi-touch operation is not supported on this unit. 20GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 21 Tuesday, June 5, 2018 9:32 AM Radio reception USB playback The radio reception is poor. Items cannot be played. Static noise occurs. q Reconnect the USB device. q Connect the antenna (aerial) firmly. The USB device takes longer to play. q The USB device contains large-sized files or files RDS with a complicated tree structure. PTY displays [PTY not found.]. q The current station is not an RDS station, or the Audio files cannot be played. radio reception is poor. q USB devices formatted with file systems other than FAT12, FAT16, FAT32 or exFAT are unsupported.* Picture * This unit supports FAT12, FAT16, FAT32 and exFAT, but There is no picture/picture noise occurs. some USB device may not support all of these. For details, refer to the operating instructions of each USB device or q A connection has not been made correctly. contact the manufacturer. q Check the connection between this unit and other equipment and set the input selector of the equipment to the source corresponding to this BLUETOOTH function unit. The other BLUETOOTH device cannot detect this q Installation is not correct. unit. – Install the unit at an angle of less than 30° in a q Set [Bluetooth Connection] to [ON] (page 18). sturdy part of the car. q While connecting to a BLUETOOTH device, this q The parking cord (light green) is not connected to unit cannot be detected by another device. the parking brake switch cord, or the parking Terminate the current connection and search for brake is not applied. this unit from the other device. The picture does not fit in the screen. q Depending on your smartphone or cellular phone, you may need to delete this unit from the q The aspect ratio is fixed on the playback source. history of the connected smartphone or cellular phone then pair them again (page 8). Sound Connection is not possible. There is no sound/sound skips/sound cracks. q Check the pairing and connection procedures in q A connection has not been made correctly. the manual of the other device, etc., and perform q Check the connection between this unit and the the operation again. connected equipment and set the input selector of the equipment to the source corresponding to The name of the detected device does not this unit. appear. q Installation is not correct. q Depending on the status of the other device, it – Install the unit at an angle of less than 30° in a may not be possible to obtain the name. sturdy part of the car. q The unit is in pause/reverse/fast-forward mode. There is no ringtone. q The settings for the outputs are not made q Raise the volume while receiving a call. correctly. q The volume is too low. The talker’s voice volume is low. q The ATT function is activated. q Raise the volume during a call. q The format is not supported. – Check if the format is supported by this unit The other party says that the volume is too low (page 19). or high. q Adjust the [MIC Gain] level (page 14). Sound is noisy. q Keep cords and cables away from each other. Echo or noise occurs during call conversations. q Reduce the volume. q Set [Speech Quality] to [Mode 1] or [Mode 2]. (page 14). q If ambient noise other than the phone call sound is loud, try reducing this noise. – Shut the window if road noise is loud. – Lower the air conditioner if the air conditioner is loud. 21GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 22 Tuesday, June 5, 2018 9:32 AM The phone sound quality is poor. No sound is output from the car speakers during q Phone sound quality depends on reception a handsfree call. conditions of the cellular phone. q If the sound is output from the cellular phone, set – Move your car to a place where you can the cellular phone to output the sound from the enhance the cellular phone’s signal if the car speakers. reception is poor. The volume of the connected BLUETOOTH device Apple CarPlay is low or high. The Apple CarPlay icon does not appear on the q Volume level will differ depending on the HOME screen. BLUETOOTH device. q Your iPhone is not compatible with Apple – Reduce the volume level differences between CarPlay. this unit and the BLUETOOTH device (page 12). – Refer to the compatibility list on the support site on the back cover. The sound skips during audio streaming or the q Disconnect your iPhone from the USB port and BLUETOOTH connection fails. reconnect it again. q Reduce the distance between the unit and the q Apple CarPlay may not be available in your BLUETOOTH device. country or region. q If the BLUETOOTH device is stored in a case which q Make sure a certified Lightning cable is used to interrupts the signal, remove the case while connect your iPhone and the unit. using the device. q Several BLUETOOTH devices or other devices (e.g. ham radio devices) which emit radio waves are Android Auto used nearby. The Android Auto icon does not appear on the – Turn off the other devices. HOME screen. – Increase the distance between the unit and q Check your Android phone and accept the other devices. disclaimers and permission requests required to q Playback sound stops momentarily when this use Android Auto on your Android phone. unit is connecting to a cellular phone. This is not q There is no Android Auto application installed on a malfunction. your Android phone. – Download and install the Android Auto The connected BLUETOOTH device cannot be application onto your Android phone. controlled during audio streaming. q Your Android phone is not compatible with q Check that the connected BLUETOOTH device Android Auto. supports AVRCP. – Android phone with Android 5.0 or higher is Some functions do not work. required. Refer to the compatibility list on the support site on the back cover. q Check that the connecting device supports the q Disconnect your Android phone from the USB functions in question. port and reconnect it again. A call is answered unintentionally. q Android Auto may not be available in your q The connecting phone is set to start a call country or region. automatically. q [Auto Answer] of this unit is set to [ON] (page 14). Pairing failed due to time out. q Depending on the connecting device, the time limit for pairing may be short. Try completing the pairing within the time. Cannot pair. q The unit may not be able to pair with a previously paired BLUETOOTH device after initializing the unit if the pairing information of the unit is on the BLUETOOTH device. In this case, delete the pairing information of the unit from the BLUETOOTH device, and then pair them again. The BLUETOOTH function cannot be operated. q Turn the ignition off. Wait for a while, then turn the ignition to the ACC position. 22GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 23 Tuesday, June 5, 2018 9:32 AM Messages General Cannot play this content. q The currently selected content cannot be played back, or skipped to the next one. – The content is not in a supported file format. Check supported file formats (page 19). Device no response q The unit does not recognize the connected USB device. – Reconnect the USB device. – Check that the USB device is supported by the unit. No Playable Data q The USB device has no playable data. – Load music data/files into the USB device. Overcurrent caution on USB. q The USB device is overloaded. – Disconnect the USB device. – Indicates that the USB device is out of order, or an unsupported device is connected. USB device not supported q For details on the compatibility of your USB device, visit the support site on the back cover. USB hub not supported q USB hubs are not supported on this unit. BLUETOOTH Bluetooth device is not found. q The unit cannot detect a connectable BLUETOOTH device. – Check the BLUETOOTH setting of the connecting device. q No device is in the list of registered BLUETOOTH devices. – Perform pairing with a BLUETOOTH device (page 8). Handsfree device is not available. q A cellular phone is not connected. –Connect a cellular phone (page9). If these solutions do not help improve the situation, consult your nearest Sony dealer. 23GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 24 Tuesday, June 5, 2018 9:32 AM Parts List for Installation Connection/Installation ʓ ʔ Cautions 5 × max. 8 mm (7/32 × max. 5/16 in) • Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes ×4 battery drain. ʕ ʖ • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw or caught in moving parts (e.g., seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power supply leads This parts list does not include all the package only after all other leads have been connected. contents. • Be sure to insulate any loose unconnected leads with electrical tape for safety. Precautions • Choose the installation location carefully so that the unit will not interfere with normal driving operations. • Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts. • Use only the supplied mounting hardware for a safe and secure installation. Note on the power supply lead (yellow) When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating. Mounting angle adjustment Adjust the mounting angle to less than 30°. 24GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 25 Tuesday, June 5, 2018 9:32 AM Connection Subwoofer*1 *3 *3 *3 Power amplifier*1 *3 Rear view camera*1 ʕ*6*7 from a wired remote control (not supplied)*4 Smartphone, USB device (for audio/video playback)*8 ʓ White White/black striped Front speaker*1*2 Gray Gray/black striped Green Green/black striped Rear speaker*1*2 Purple Purple/black striped Black Yellow Red For details, see “Making Blue/white striped connections” (page 28). Orange/white striped Light green Purple/white striped from a car antenna (aerial)*5 25GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 26 Tuesday, June 5, 2018 9:32 AM *1 Not supplied ɣ To the parking brake switch cord *2 Speaker impedance: 4 Ω – 8 Ω × 4 The mounting position of the parking brake *3 RCA pin cord (not supplied) *4 Depending on the type of car, use an adaptor for a wired switch cord depends on your car. remote control (not supplied). Be sure to connect the parking brake lead (light For details on using the wired remote control, see “Using green) of the power supply connection cable ʓ the wired remote control” (page 29). to the parking brake switch cord. *5 Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit. Parking brake switch cord *6 Whether in use or not, route the microphone input cord so it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet. *7 For details on installing the microphone, see “Installing the microphone” (page28). *8 Do not use a USB extension cable. Hand brake type Foot brake type Making connections ɤ To the +12 V power terminal of the car’s rear ɞ To a common ground (earth) point lamp lead (only when connecting the rear First connect the black ground (earth) lead then view camera) connect the yellow and red power supply leads. ɟ To the +12 V power terminal which is Memory hold connection energized at all times When the yellow power supply lead is connected, Be sure to first connect the black ground (earth) power will always be supplied to the memory lead to a common ground (earth) point. circuit even when the ignition switch is turned off. ɠ To the +12 V power terminal which is energized when the ignition switch is set to Speaker connection the accessory position • Before connecting the speakers, turn the unit off. Be sure to first connect the black ground (earth) • Use speakers with an impedance of 4 Ω to 8 Ω and lead to a common ground (earth) point. with adequate power handling capacities to avoid damage. ɡ To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) booster Installing the microphone It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) To capture your voice during handsfree calling, you booster, or with a manually-operated telescopic need to install the microphone ʕ. antenna (aerial). To AMP REMOTE IN of an optional power ʕ amplifier This connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit. Note It will take about 10 seconds to shut down the output of REM OUT after the unit is turned off. ɢ To a car’s illumination signal Clip (not supplied) Be sure to first connect the black ground (earth) lead to a common ground (earth) point. ʕ ʖ 26GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 27 Tuesday, June 5, 2018 9:32 AM Cautions • It is extremely dangerous if the cord becomes Installation wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations. Mounting the unit in a Japanese car • If airbags or any other shock-absorbing You may not be able to install this unit in some equipment are in your car, contact the store where Japanese cars. In such a case, consult your Sony you purchased this unit or the car dealer before dealer. installation. ʔ Note Before attaching the double-sided tape ʖ, clean the To the dashboard/center console surface of the dashboard with a dry cloth. Using the wired remote control Bracket When using the steering wheel remote Bracket control Installation of the connection cable RC-SR1 (not supplied) is required before use. Parts supplied with ʔ 1 To enable the steering wheel remote control, select your car [General] q [Steering Control] q [Custom] q [ ] to make the registration (page 17). When the registration is complete, the steering When mounting this unit to the preinstalled wheel remote control becomes available. brackets of your car, use the supplied screws ʔ in Notes on installing the connection cable RC-SR1 (not the appropriate screw holes based on your car: supplied) T for TOYOTA and N for NISSAN. • Refer to the support site on the back cover for details then connect each lead properly to the appropriate leads. Making an improper connection may damage the unit. • Consulting the dealer or an experienced technician for help is recommended. When using the wired remote control 1 To enable the wired remote control, set [Steering Control] in [General] to [Preset] (page 17). Note To prevent a malfunction, install only with the supplied screws ʔ. Using the rear view camera Installation of the rear view camera (not supplied) is required before use. Fuse replacement The picture from a rear view camera connected to When replacing the fuse, be sure to Fuse (10 A) the CAMERA IN terminal is displayed when: use one matching the amperage ˋ the back lamp of your car lights up (or the shift rating stated on the original fuse. lever is set to the R (reverse) position). If the fuse blows, check the power ˋ you press HOME, then touch [Rear Camera]. connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. 27GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Left XAVAX3000UC\040CD.fm 010COV.book Page 28 Tuesday, June 5, 2018 9:32 AM 28GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: Right XAVAX3000UC\040CD.fm 010COV.book Page 29 Tuesday, June 5, 2018 9:32 AM 29GB :#8#:  

F:\#Work#\Y3\eV\Sona2\Sagyo data\4739317211\4739317211XAVAX3000UC\01GB- masterpage: BCO XAVAX3000UC\050BCO.fm 010COV.book Page 30 Tuesday, June 5, 2018 9:32 AM Support site Site d’assistance Sitio Web de soporte If you have any questions or for the Si vous avez des questions ou si vous técnico en línea latest support information on this souhaitez consulter les toutes Para resolver cualquier duda u obtener product, please visit the web site dernières informations techniques la información más reciente sobre el below: sur ce produit, rendez-vous sur le soporte técnico de este producto, site Web suivant : visite el siguiente sitio Web: http://esupport.sony.com/ If you have any questions/problems regarding this product, try the following: 1 Read Troubleshooting in these Operating Instructions. 2 Please contact (U.S.A. only); Call 1-800-222-7669 URL http://www.SONY.com Smartphone app App. de smartphone Aplicación para Support by Sony app - Find Support by Sony app - Trouvez des Smartphone information and get notification infos et recevez des notifications au Aplicación Support by Sony - Busque about your product: sujet de votre produit : información y obtenga notificaciones acerca de su producto: √ News & Alerts / Actus & Alertes / Noticias y Alertas √ Software updates / Mises à jour / Actualizaciones de software √ Tutorials / Didacticiels / Tutoriales √ Tips & Tricks / Conseils & Astuces / Consejos y Trucos https://sony.net/SBS ©201 Sony Corporation Printed in Thailand http://www.sony.net/ :#8#:  


Document Created: 2019-02-22 09:30:08
Document Modified: 2019-02-22 09:30:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC