03 FCC Test Report_NII_1

FCC ID: AK8NWA100

Test Report

Download: PDF
FCCID_4382419

Project No: JB-Z0543-B Page 1 of 351 RADIO TEST REPORT (for 5 GHz WLAN) Project No. : JB-Z0543-B Client : Sony Corporation Client’s Address : 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan Product Name : Digital Media Player Model No. : NW-A105 FCC ID : AK8NWA100 Test Standard : 47 CFR Part 15 Subpart E Sample Receipt Date : May 21, 2019 Test Date : May 28, 2019 to June 26, 2019 Original Report Date : July 5, 2019 Amend Report Date : August 1, 2019 Test Result : Complied Notice : * These test results relate only to the items (combination equipment, test configuration, operation condition etc.) tested. * This report shall not be reproduced except in full, without written approval of the laboratory. * This report must not be used by the client to claim product endorsement by A2LA or any agency of the U.S. * Hereby certify that no party is subject to a denial of federal benefits pursuant to section 5301 of the Anti-Drug Abuse Act. * All test results are traceable to the national and / or international standards. * The testing in which “Non-accreditation” is displayed is outside the accreditation scopes in Sony Global Manufacturing & Operations Corporation EMC/ RF Test Laboratory. * This report replaces and supersedes all previous versions. Refer to Revision History on the following page. Reported by: Takanori Oho Technical Manager EMC/RF Test Laboratory, Main Lab. Design Technology Division Approved Signatory: Teruki Kurihara Technical Manager EMC/RF Test Laboratory, Main Lab. Design Technology Division TESTING CERT #3203.01 Format No.: NV1-1-01 Version 5.0 Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 2 of 351 TABLE OF CONTENTS 1. General Information ........................................................................................................................................................3 1.1. Description of Equipment Under Test (EUT)...................................................................................................... 3 1.2. Summary of Test Result .........................................................................................................................................4 1.3. Tested Methodology ................................................................................................................................................4 1.4. Measurement Procedures ......................................................................................................................................5 1.5. Test Location ............................................................................................................................................................7 1.6. Uncertainty ..............................................................................................................................................................7 2. Test Specification .............................................................................................................................................................8 2.1. Validation .................................................................................................................................................................8 2.2. Operating Condition................................................................................................................................................8 2.3. Special Accessories ..................................................................................................................................................9 2.4. EUT Modifications ..................................................................................................................................................9 2.5. Configuration of EUT System .............................................................................................................................10 2.6. View of Measurement Facility .............................................................................................................................12 3. Test Data.........................................................................................................................................................................13 3.1. AC Power-line Conducted Emissions .................................................................................................................13 3.2. 26dB Emission Bandwidth ..................................................................................................................................15 3.3. 6dB Emission Bandwidth.....................................................................................................................................22 3.4. 99% Occupied Bandwidth ....................................................................................................................................25 3.5. Maximum Conducted Output Power .................................................................................................................38 3.6. Maximum Power Spectral Density .....................................................................................................................41 3.7. Unwanted Emissions ............................................................................................................................................54 4. Method of Calculation .................................................................................................................................................347 4.1. AC Power-line Conducted Emissions ...............................................................................................................347 4.2. Maximum Conducted Output Power ...............................................................................................................347 4.3. Maximum Power Spectral Density ...................................................................................................................347 4.4. Unwanted Emissions ..........................................................................................................................................348 5. List of Test Equipment................................................................................................................................................349 5.1. AC Power-line Conducted Emissions ...............................................................................................................349 5.2. Antenna-port Conducted Measurements.........................................................................................................349 5.3. Unwanted Emissions ..........................................................................................................................................349 6. Photographs of test setup............................................................................................................................................350 6.1. AC Power-line Conducted Emissions Photo(s) ................................................................................................350 6.2. Antenna-port Conducted Measurements Photo(s) .........................................................................................350 6.3. Unwanted Emissions Photo(s)...........................................................................................................................351 Note -indicates that the listed condition, standard or equipment is applicable for this report. -indicates that the listed condition, standard or equipment is not applicable for this report. Revision History Revision Date Overview Page JB-Z0543 (Original) June 26, 2019 - - JB-Z0543-A July 26, 2019 Add procedures and measurement facility drawings for spurious. P.6,12 JB-Z0543-B August 1, 2019 Correction of Maximum Conducted Output Power result and P38 Margin. Add description to procedures for spurious emission. P.6 Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 3 of 351 1. General Information 1.1. Description of Equipment Under Test (EUT) General Specification Test Sample Condition : Prototype Pre-production Mass-production Product Name : Digital Media Player Trade Name : SONY Model No. : NW-A105 Serial No. : 3, 5 Power Rating of the EUT : DC 3.7 V (Internal Battery) or DC 5 V (USB) Similar model(s) to be covered by this report Model No. : None Radio Specification Function of the Equipment : Transceiver Operating Frequency : IEEE Standard Operating Frequency Channel Channel Number of Spacing Bandwidth Channel 802.11a/n HT20 5180 - 5320 MHz, 20 MHz 20 MHz 8 802.11ac VHT20 5500 - 5720 MHz 9 (except 5600 - 5640 MHz), 5745 - 5825 MHz 5 802.11n HT40 5190 - 5310 MHz, 40 MHz 40 MHz 4 802.11ac VHT40 5510 - 5710 MHz 4 (except 5590 - 5630 MHz), 5755 - 5795 MHz 2 802.11ac VHT80 5210 - 5290 MHz, 80 MHz 80 MHz 2 5530 - 5690 MHz 2 (except 5610 MHz), 5775 MHz 1 Modulation Type : OFDM (BPSK, QPSK, 16QAM, 64QAM, 256QAM) Antenna Type : Inverted-F antenna Antenna Connector Type : None Antenna Gain : +3.0 dBi Operating Temperature : +5 to +35 deg.C Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 4 of 351 1.2. Summary of Test Result Test Item Test Method Worst Margin Results Note 18.2 dB (QP) AC Power-line Conducted Emissions Conducted 0.180 MHz Complied - L1 26dB Emission Bandwidth Conducted Refer to the test data N/A - 6dB Emission Bandwidth Conducted Refer to the test data Complied - Maximum Conducted Output Power Conducted 16.77 dB Complied - Maximum Power Spectral Density Conducted 8.25 dB Complied - 2.6 dB (PK) Unwanted Emissions Radiated 5725.000 MHz Complied - Vertical Dynamic Frequency Selection - - - *1 Note *1: For DFS test results, referred to JB-Z0544 issued by Sony Global Manufacturing & Operations Corporation. Other requirements Part 15.31(e) Supply voltage requirement : Complied (The voltage supplied from USB or battery are converted to regulated DC voltage by the built-in power circuit of the EUT.) Part 15.203 / 212 Antenna requirement : Complied (The EUT has an internal antenna which cannot be replaced by users.) 1.3. Tested Methodology Test Standard : 47 CFR Part15 Subpart E Test Method : ANSI C63.10 - 2013 KDB 789033 D02 General UNII Test Procedures New Rules v02r01 Test Condition AC Power-line Conducted Emissions Dimensions of the EUT table : 0.8 m height, 1.5 m width and 1 m depth. Unwanted Emissions Test Distance : 3m 10m (9 kHz to 30 MHz) 3m 10m (30 MHz to 1000 MHz) 3m (1 GHz to 40 GHz) Dimensions of the EUT table : 0.8 m (below 1 GHz) or 1.5 m (above 1 GHz) height, 2 m width and 1 m depth. Dimensions of validated test volume : 2.5 m diameter, 3 m top height, 0.5 m bottom height. Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 5 of 351 1.4. Measurement Procedures We performed the measurements in accordance with NV3-10, available upon the request. No deviation Deviation from the above procedure The summary of the above procedure is mentioned below AC Power-line Conducted Emissions 1. The non-conductive table (EUT table) made of ( FRP, wood, other non-conductive material) was placed 0.4 m from its rear to the vertical reference ground plane. 2. The EUT was placed on the center of tabletop and its rear was flush with the rear of the table, connected through a LISN to the input power mains. 3. The LISN was placed in 80 cm from the nearest part of the EUT chassis. 4. The excess length of the AC cable between the EUT and the LISN receptacle, or an adaptor or extension cable connected to and measured with LISN, was folded back and forth at the center of the lead to form a bundle not exceeding 40 cm in length. 5. The connection of the all other equipment to the second LISN was performed. The second LISN was terminated with a 50-ohm terminator. 6. Interconnecting cables that hang closer than 40 cm to the horizontal reference ground plane was folded back and forth forming a bundle 30 to 40 cm long, hanging approximately in the middle between the horizontal reference ground plane and the tabletop. 7. Find the worst mode and arrangement of the EUT according to the follows; - Connecting all peripherals and change the position of peripherals and cables. - Changing the all test operation modes of the EUT. - On every condition, exploring the highest emissions with the spectrum analyzer. (150 kHz to 30 MHz, peak detector, RBW: 10 kHz) 8. On the worst condition of the EUT found in above, choose the six highest emissions on the spectrum data. The final measurements carried out on these emissions with EMI test receiver. (quasi-peak and average detector, RBW: 9 kHz) Antenna-port Conducted Measurements 1. Antenna-port of the EUT was connected to the power sensor (Maximum Conducted Output Power) or the spectrum analyzer. (other test items). 2. For each EUT operation mode, the Antenna-port Conducted Measurements were measured with the power sensor or the spectrum analyzer. Test Item Detector RBW Antenna-port Conducted Measurements 100 kHz : IEEE 802.11a, 11n(HT20), 11ac(VHT20) 26dB Emission Bandwidth Peak 300 kHz : IEEE 802.11n(HT40), 11ac(VHT40) 1 MHz : IEEE 802.11ac(VHT80) 6dB Emission Bandwidth Peak 100 kHz 300 kHz : IEEE 802.11a, 11n(HT20), 11ac(VHT20) 99% Occupied Bandwidth Peak 1 MHz : IEEE 802.11n(HT40), 11ac(VHT40), 11ac(VHT80) Maximum Conducted Output Power Average - 100 kHz : U-NII-3 Maximum Power Spectral Density RMS 1 MHz : U-NII-1/ -2A/ -2C Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 6 of 351 Unwanted Emissions 1. The non-conductive table (EUT table) made of ( FRP, Styrene Foam, other non-conductive material) was placed in the center of the turntable. 2. The EUT was placed on the center of the tabletop. 3. The test antenna was placed away from the EUT at test distance. 4. The limits were compensated the distance factor with follows; 9 kHz to 490 kHz [Limit at 3 m] = [Limit at 300 m] + 40log (300[m] / 3[m]) 490 kHz to 30 MHz [Limit at 3 m] = [Limit at 30 m] + 40log (30[m] / 3[m]) 5. Find the worst arrangement of the EUT according to follows; - Rotating the turntable and/or scanning the antenna. - On every condition, exploring the highest emissions with the spectrum analyzer. (9 kHz to 40 GHz, peak detector) 6. On the worst arrangement of the EUT found in above, choose the six highest harmonics or spurious emissions on the spectrum data.(*excluding carrier band edges) The final measurements of all test operating modes carried out on these emissions as follows; The test antenna and the turntable were performed with follows; 9 kHz to 30 MHz 30 MHz to 1000 MHz 1 GHz to 40 GHz Antenna Loop Antenna Bi-conical Antenna, Horn Antenna Log-periodic Antenna Antenna 1 m, 1 m to 4 m, 1 m to 4 m *, scanning range Vertical, 360 degrees Horizontal and Vertical Horizontal and Vertical Turntable 360 degrees 360 degrees 360 degrees rotating range *: When the measurement frequencies above 1 GHz, final measurements are performed keeping the antenna in the "cone of radiation" from EUT area and pointed at the area both in azimuth and elevation, with polarization oriented for maximum response. Instruments settings were carried out with follows; 9 kHz to 90 kHz 90 kHz to 110 kHz 30 MHz to 1000 MHz 1 GHz to 40 GHz 110 kHz to 490 kHz 490 kHz to 30 MHz Detector Peak / Average Quasi-peak Quasi-peak Peak / Average RBW 200 Hz (6 dB) or 200 Hz (6 dB) or 120 kHz (6 dB) 1 MHz (6 dB) 9 kHz (6 dB) *1 9 kHz (6 dB) *1 VBW N/A N/A N/A 3 MHz (for peak) 10 kHz (for average) *2 Instrument EMI test receiver EMI test receiver EMI test receiver Spectrum analyzer *1: When the measurement frequencies below 150 kHz, RBW: 200 Hz was used. *2: VBW setting (for average) was higher than 1/T. (T is the minimum transmission duration) 7. If the final average measurement result exceeded the limit in the authorized band edge, the integration method is carried out with follows; Unwanted emissions within 2 MHz of the band edge Detector Peak RBW 100 kHz (6 dB) Instrument Spectrum analyzer Function Channel Power (integration BW : 1 MHz) 8. Although these tests for below 30MHz were performed other than open field area test site, adequate comparison measurements were confirmed against 30 m open field area test site. Therefore sufficient tests were made to demonstrate that the alternative site produces results that correlate with the ones of tests made in an open field based on KDB 414788 D01. Further these test for above 1GHz were performed test site complied with CISPR 16-1-4. In the case of EUT size smaller than the validated test volume, the antenna position is adjusted such that the distance between the EUT and the antenna reference point is identical to the 3m used for the S-VSWR validation measurements. These method based on clause 7.3.1 of CISPR16-1-4 Edition 4, therefore correcting distance factor is not applied. Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 7 of 351 1.5. Test Location Test Facility Name : Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. Address : 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan Phone : +81 438 37 2750 A2LA Certificate No. : 3203.01 Cert. Validated Date : Oct. 31, 2019 AC Power-line Conducted Emissions Shielded Room 4th Site EMC Site Antenna-port Conducted Measurements Shielded Room 4th Site SR1 Unwanted Emissions Semi-Anechoic chamber 4th Site EMC Site 1.6. Uncertainty Test Item Frequency 4th Site SR1 Maximum Conducted Output Power 1 GHz to 6 GHz ± 0.84 dB Maximum Power Spectral Density below 6 GHz ± 1.25 dB Test Item Frequency Distance 4th Site EMC Site AC Power-line Conducted Emissions 150 kHz to 30 MHz - ± 3.34 dB ± 3.35 dB 9 kHz to 30 MHz 3m ± 2.60 dB ± 3.13 dB 30 MHz to 1000 MHz 3m ± 4.96 dB ± 5.26 dB Radiated Emissions 1 GHz to 18 GHz 3m ± 5.22 dB ± 5.50 dB 18 GHz to 26.5 GHz 3m ± 5.36 dB ± 5.63 dB 26.5 GHz to 40 GHz 3m ± 6.07 dB ± 6.31 dB Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 8 of 351 2. Test Specification 2.1. Validation The system was configured for testing in a typical (as a customer would normally use it). The tests were conducted with the worst-case modes as follows. 2.2. Operating Condition The tests have been carried out the following conditions. [ Transmitting mode ] Test Channels [MHz] Test Items Worst Data Rate *1 U-NII-1 U-NII-2A U-NII-2C U-NII-3 AC Power-line Conducted Emissions *2 5180 - - - 802.11a : 18 Mbps 5500 5260 802.11a : 18 Mbps 5580 - 5300 - 802.11n(HT20) : MCS6 5700 5320 802.11ac(VHT20) : MCS6 5720 5510 26dB Emission Bandwidth 5270 5550 802.11n(HT40) : MCS4 - - 5310 5670 802.11ac(VHT40) : MCS4 5710 5530 - 5290 - 802.11ac(VHT80) : MCS6 5690 5745 802.11a : 18 Mbps - - - 5785 802.11n(HT20) : MCS6 5825 802.11ac(VHT20) : MCS6 6dB Emission Bandwidth 5755 802.11n(HT40) : MCS4 - - - 5795 802.11ac(VHT40) : MCS4 - - - 5775 802.11ac(VHT80) : MCS6 5180 5260 5500 5745 802.11a : 18 Mbps 5200 5280 5580 5785 802.11n(HT20) : MCS6 5220 5300 5700 5825 802.11ac(VHT20) : MCS6 5240 5320 5720 5510 Maximum Conducted Output Power 5190 5270 5550 5755 802.11n(HT40) : MCS4 5230 5310 5670 5795 802.11ac(VHT40) : MCS4 5710 5530 5210 5290 5775 802.11ac(VHT80) : MCS6 5690 5500 5180 5260 5745 802.11a : 18 Mbps 5580 5220 5300 5785 802.11n(HT20) : MCS6 5700 5240 5320 5825 802.11ac(VHT20) : MCS6 5720 5510 99% Occupied Bandwidth, 5190 5270 5550 5755 802.11n(HT40) : MCS4 Maximum Power Spectral Density 5230 5310 5670 5795 802.11ac(VHT40) : MCS4 5710 5530 5210 5290 5610 5775 802.11ac(VHT80) : MCS6 5690 Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 9 of 351 Test Channels [MHz] Test Items Worst Data Rate *1 U-NII-1 U-NII-2A U-NII-2C U-NII-3 Unwanted Emissions *2 5180 - - - 802.11a : 18 Mbps ( Below 1 GHz ) 5500 5745 5260 802.11a : 18 Mbps 5180 5580 *3 5785 *3 5320 802.11ac(VHT20) : MCS6 5700 5825 Unwanted Emissions 5510 ( Above 1 GHz ) 5270 5755 802.11n(HT40) : MCS4 5190 5550 *4 5310 5795 802.11ac(VHT40) : MCS4 5670 5210 5290 5530 5775 802.11ac(VHT80) : MCS6 Note *1: The worst data rate has been decided based on the result of Maximum Conducted Output Power. *2: The test was performed with the representative mode that had been found as the worst emissions while exploratory testing. *3: It applies only to IEEE802.11a. *4: It applies only to IEEE802.11n. The Software for Operating Mode Software Name : LBEE5ZZ1PJ-331 RF Test Software Version : 0.6 2.3. Special Accessories Special accessories needed for connecting the EUT to achieve compliance: Item Manufacturer Model No. Serial No. Remark - - - - - 2.4. EUT Modifications No equipment modification to achieve compliance to the standard levels was done during the tests. Equipment was modified to achieve compliance to the standard level as below. Responsible Party Signature Typed/ Print Name : Responsible Party : Position : Date : Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 10 of 351 2.5. Configuration of EUT System AC Power-line Conducted Emissions [ EUT and Associated Equipment (AE) ] EUT/ Symbol Item Manufacturer Model No. Serial No. AE A EUT Digital Media Player SONY NW-A105 3 B AE PERSONAL COMPUTER SONY VJS131C11N 4120398 C AE AC ADAPTER SONY VJ8AC10V9 274969 [ Type of Cable ] Identification Shielded Ferrite Length Symbol Description Bundled (Manufacturer etc.) Yes / No Core (m) 1 USB Cable Kailai Yes No 0.5 No 2 DC Cable - No No 1.8 Yes 3 AC Cable - No No 1.5 Yes [ Connecting Diagram ] A: Digital Media 1 B: PERSONAL Player COMPUTER WLAN 2 Transmitting C: AC ADAPTER 3 AC120V 60Hz Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 11 of 351 Antenna-port Conducted Measurements [ EUT and Associated Equipment (AE) ] EUT/ Symbol Item Manufacturer Model No. Serial No. AE A EUT Digital Media Player SONY NW-A105 5 [ Type of Cable ] Identification Shielded Ferrite Length Symbol Description Bundled (Manufacturer etc.) Yes / No Core (m) - - - - - - - [ Connecting Diagram ] Measurement A: RF Cable Digital Media Equipment Player Unwanted Emissions [ EUT and Associated Equipment (AE) ] EUT/ Symbol Item Manufacturer Model No. Serial No. AE A EUT Digital Media Player SONY NW-A105 3 [ Type of Cable ] Identification Shielded Ferrite Length Symbol Description Bundled (Manufacturer etc.) Yes / No Core (m) - - - - - - - [ Connecting Diagram ] WLAN A: Transmitting Digital Media Player Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 12 of 351 2.6. View of Measurement Facility Radiated spurious emissions < 9 kHz - 30 MHz > Side view 3m Scan from 0 to 360deg. (Vertical) EUT EMI Receiver RF Selector 1.0m Non conducted 0.8m Turntable Reference Ground Plane < 30 MHz - 1000 MHz > Side view EMI Receiver Scan from 1m to 4m 3m (Horizontal / Vertical) EUT Non conducted 3dB RF Selector 0.8m ATT Turntable Pre-Amp Reference Ground Plane < 1 GHz - 40 GHz > Side view EMI 7 – 40 GHz 3m Pre-AMP Receiver 1 - 7 GHz EUT Pre-AMP Filter Non conducted Non conducted 1.5m Scan from 1m to 4m 0.3m (Horizontal / Vertical) Turntable Reference Ground Plane Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 13 of 351 3. Test Data 3.1. AC Power-line Conducted Emissions 1) Date of measurement : June 10, 2019 The test data is mentioned as follows. Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 14 of 351 [ 802.11a/ 5180 MHz ] Sony Global M&O Corp <<Conducted Emission>> Kisarazu No.1 Model : NW-A105 Limit : FCC Part15C Serial : 3 Remark1 : Operator : R.KAWANO Remark2 : Power : AC120V / 60Hz Remark3 : IEEE802.11a 18Mbps Environment : 20.3deg.C / 73.6% / 1004.8hPa Remark4 : Low [dB(μV)] 80 <FCC Part15C> Limit(QP) 70 Limit(AV) <190610_NW-A105_07> Spectrum(N,PK) 60 Spectrum(L1,PK) Peak(N) Peak(L1) 50 Interferance-QP(N) Interferance-AV(N) Interferance-QP(L1) Level 40 Interferance-AV(L1) 30 20 10 0 0.15 0.50 1.00 5.00 10.00 30.00 Frequency [MHz] Final Result --- N Phase --- No. Frequency Reading Reading c.f Result Result Limit Limit Margin Margin QP AV QP AV QP AV QP AV [MHz] [dB(μV)] [dB(μV)] [dB] [dB(μV)] [dB(μV)] [dB(μV)] [dB(μV)] [dB] [dB] 1 0.151 29.5 12.3 15.9 45.4 28.2 66.0 56.0 20.6 27.8 2 0.167 30.2 15.6 16.3 46.5 31.9 65.1 55.1 18.6 23.2 3 0.182 24.5 14.4 16.2 40.7 30.6 64.4 54.4 23.7 23.8 4 0.243 21.2 10.0 15.7 36.9 25.7 62.0 52.0 25.1 26.3 5 1.371 6.4 -0.4 15.9 22.3 15.5 56.0 46.0 33.7 30.5 6 2.684 5.9 -1.2 15.9 21.8 14.7 56.0 46.0 34.2 31.3 --- L1 Phase --- No. Frequency Reading Reading c.f Result Result Limit Limit Margin Margin QP AV QP AV QP AV QP AV [MHz] [dB(μV)] [dB(μV)] [dB] [dB(μV)] [dB(μV)] [dB(μV)] [dB(μV)] [dB] [dB] 1 0.153 30.3 11.5 16.0 46.3 27.5 65.8 55.8 19.5 28.3 2 0.165 31.1 16.7 16.2 47.3 32.9 65.2 55.2 17.9 22.3 3 0.180 30.1 18.3 16.2 46.3 34.5 64.5 54.5 18.2 20.0 4 0.196 26.2 11.3 16.0 42.2 27.3 63.8 53.8 21.6 26.5 5 0.281 16.9 6.3 15.8 32.7 22.1 60.8 50.8 28.1 28.7 6 0.929 12.5 4.8 16.0 28.5 20.8 56.0 46.0 27.5 25.2 Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 15 of 351 3.2. 26dB Emission Bandwidth 1) Ambient temperature ： 19.6 deg.C 22.6 deg.C 21.6 deg.C 2) Relative humidity ： 55.9 % 50.6 % 64.7 % 3) Date of measurement ： June 14, 2019 June 17, 2019 June 18, 2019 4) Measured by ： H.WAKI H.WAKI H.WAKI 5) Operating mode ： Transmitting mode Rate Channel Result Limit Mode [Mbps] [MHz] [MHz] [MHz] 5260 18.196 - 5300 18.188 - 5320 18.248 - 11a 18 5500 18.216 - 5580 18.196 - 5700 18.172 - 5720 18.164 - 5260 20.292 - 5300 20.292 - 5320 20.300 - 11n MCS6 5500 20.284 - (HT20) 5580 20.276 - 5700 20.280 - 5720 20.268 - 5270 42.560 - 5310 42.568 - 11n 5510 42.528 - MCS4 (HT40) 5550 42.520 - 5670 42.616 - 5710 42.544 - 5260 20.540 - 5300 20.352 - 5320 20.316 - 11ac MCS6 5500 20.352 - (VHT20) 5580 20.304 - 5700 20.304 - 5720 20.288 - 5270 43.216 - 5310 43.704 - 11ac 5510 43.520 - MCS4 (VHT40) 5550 43.432 - 5670 43.544 - 5710 43.408 - 5290 85.760 - 11ac MCS6 5530 87.824 - (VHT80) 5690 84.976 - Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 16 of 351 [ 802.11a/ 5260 MHz ] [ 802.11a/ 5300 MHz ] [ 802.11a/ 5320 MHz ] [ 802.11a/ 5500 MHz ] [ 802.11a/ 5580 MHz ] [ 802.11a/ 5700 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 17 of 351 [ 802.11a/ 5720 MHz ] [ 802.11n (HT20)/ 5260 MHz ] [ 802.11n (HT20)/ 5300 MHz ] [ 802.11n (HT20)/ 5320 MHz ] [ 802.11n (HT20)/ 5500 MHz ] [ 802.11n (HT20)/ 5580 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 18 of 351 [ 802.11n (HT20)/ 5700 MHz ] [ 802.11n (HT20)/ 5720 MHz ] [ 802.11n (HT40)/ 5270 MHz ] [ 802.11n (HT40)/ 5310 MHz ] [ 802.11n (HT40)/ 5510 MHz ] [ 802.11n (HT40)/ 5550 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 19 of 351 [ 802.11n (HT40)/ 5670 MHz ] [ 802.11n (HT40)/ 5710 MHz ] [ 802.11ac (VHT20)/ 5260 MHz ] [ 802.11ac (VHT20)/ 5300 MHz ] [ 802.11ac (VHT20)/ 5320 MHz ] [ 802.11ac (VHT20)/ 5500 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 20 of 351 [ 802.11ac (VHT20)/ 5580 MHz ] [ 802.11ac (VHT20)/ 5700 MHz ] [ 802.11ac (VHT20)/ 5720 MHz ] [ 802.11ac (VHT40)/ 5270 MHz ] [ 802.11ac (VHT40)/ 5310 MHz ] [ 802.11ac (VHT40)/ 5510 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 21 of 351 [ 802.11ac (VHT40)/ 5550 MHz ] [ 802.11ac (VHT40)/ 5670 MHz ] [ 802.11ac (VHT40)/ 5710 MHz ] [ 802.11ac (VHT80)/ 5290 MHz ] [ 802.11ac (VHT80)/ 5530 MHz ] [ 802.11ac (VHT80)/ 5690 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 22 of 351 3.3. 6dB Emission Bandwidth 1) Ambient temperature ： 19.6 deg.C 22.6 deg.C 21.6 deg.C 2) Relative humidity ： 55.9 % 50.6 % 64.7 % 3) Date of measurement ： June 14, 2019 June 17, 2019 June 18, 2019 4) Measured by ： H.WAKI H.WAKI H.WAKI 5) Operating mode ： Transmitting mode Rate Channel Result Limit Mode [Mbps] [MHz] [MHz] [MHz] 5745 15.140 0.5 11a 18 5785 15.136 0.5 5825 15.136 0.5 5745 17.664 0.5 11n MCS6 5785 17.664 0.5 (HT20) 5825 17.664 0.5 11n 5755 36.448 0.5 MCS4 (HT40) 5795 36.432 0.5 5745 17.660 0.5 11ac MCS6 5785 17.680 0.5 (VHT20) 5825 17.656 0.5 11ac 5755 36.448 0.5 MCS4 (VHT40) 5795 36.448 0.5 11ac MCS6 5775 76.064 0.5 (VHT80) [ 802.11a/ 5745 MHz ] [ 802.11a/ 5785 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 23 of 351 [ 802.11a/ 5825 MHz ] [ 802.11n (HT20)/ 5745 MHz ] [ 802.11n (HT20)/ 5785 MHz ] [ 802.11n (HT20)/ 5825 MHz ] [ 802.11n (HT40)/ 5755 MHz ] [ 802.11n (HT40)/ 5795 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 24 of 351 [ 802.11ac (VHT20)/ 5745 MHz ] [ 802.11ac (VHT20)/ 5785 MHz ] [ 802.11ac (VHT20)/ 5825 MHz ] [ 802.11ac (VHT40)/ 5755 MHz ] [ 802.11ac (VHT40)/ 5795 MHz ] [ 802.11ac (VHT80)/ 5775 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 25 of 351 3.4. 99% Occupied Bandwidth 1) Ambient temperature ： 19.6 deg.C 22.6 deg.C 21.6 deg.C 2) Relative humidity ： 55.9 % 50.6 % 64.7 % 3) Date of measurement ： June 14, 2019 June 17, 2019 June 18, 2019 4) Measured by ： H.WAKI H.WAKI H.WAKI 5) Operating mode ： Transmitting mode Rate Channel Result Limit Mode [Mbps] [MHz] [MHz] [MHz] 5180 16.308 - 5220 16.312 - 5240 16.308 - 5260 16.316 - 5300 16.320 - 5320 16.312 - 11a 18 5500 16.312 - 5580 16.304 - 5700 16.312 - 5720 16.320 - 5745 16.312 - 5785 16.308 - 5825 16.312 - 5180 17.852 - 5220 17.856 - 5240 17.848 - 5260 17.840 - 5300 17.836 - 5320 17.848 - 11n MCS6 5500 17.852 - (HT20) 5580 17.860 - 5700 17.856 - 5720 17.856 5745 17.848 - 5785 17.848 - 5825 17.860 - 5190 37.080 - 5230 37.104 - 5270 37.080 - 5310 37.096 - 11n 5510 37.072 - MCS4 (HT40) 5550 37.088 - 5670 37.096 - 5710 37.128 - 5755 37.072 - 5795 37.064 - Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 26 of 351 Rate Channel Result Limit Mode [Mbps] [MHz] [MHz] [MHz] 5180 17.860 - 5220 17.852 - 5240 17.856 - 5260 17.852 - 5300 17.852 - 5320 17.856 - 11ac MCS6 5500 17.864 - (VHT20) 5580 17.852 - 5700 17.852 - 5720 17.860 - 5745 17.852 - 5785 17.860 - 5825 17.860 - 5190 37.296 - 5230 37.208 - 5270 37.320 - 5310 37.288 - 11ac 5510 37.304 - MCS4 (VHT40) 5550 37.216 - 5670 37.232 - 5710 37.264 - 5755 37.288 - 5795 37.288 - 5210 76.592 - 5290 76.560 - 11ac MCS6 5530 76.576 - (VHT80) 5690 76.544 - 5775 76.544 - [ 802.11a/ 5180 MHz ] [ 802.11a/ 5220 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 27 of 351 [ 802.11a/ 5240 MHz ] [ 802.11a/ 5260 MHz ] [ 802.11a/ 5300 MHz ] [ 802.11a/ 5320 MHz ] [ 802.11a/ 5500 MHz ] [ 802.11a/ 5580 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 28 of 351 [ 802.11a/ 5700 MHz ] [ 802.11a/ 5720 MHz ] [ 802.11a/ 5745 MHz ] [ 802.11a/ 5785 MHz ] [ 802.11a/ 5825 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 29 of 351 [ 802.11n (HT20)/ 5180 MHz ] [ 802.11n (HT20)/ 5220 MHz ] [ 802.11n (HT20)/ 5240 MHz ] [ 802.11n (HT20)/ 5260 MHz ] [ 802.11n (HT20)/ 5300 MHz ] [ 802.11n (HT20)/ 5320 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 30 of 351 [ 802.11n (HT20)/ 5500 MHz ] [ 802.11n (HT20)/ 5580 MHz ] [ 802.11n (HT20)/ 5700 MHz ] [ 802.11n (HT20)/ 5720 MHz ] [ 802.11n (HT20)/ 5745 MHz ] [ 802.11n (HT20)/ 5785 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021

Project No: JB-Z0543-B Page 31 of 351 [ 802.11n (HT20)/ 5825 MHz ] [ 802.11n (HT40)/ 5190 MHz ] [ 802.11n (HT40)/ 5230 MHz ] [ 802.11n (HT40)/ 5270 MHz ] [ 802.11n (HT40)/ 5310 MHz ] Sony Global Manufacturing & Operations Corporation EMC/RF Test Laboratory, Main Lab. A2LA Cert. #3203.01 8-4 Shiomi Kisarazu-shi Chiba-ken, 292-0834, Japan PHONE +81 438 37 2750 FAX +81 438 37 1021


Document Created: 2019-08-01 14:45:40
Document Modified: 2019-08-01 14:45:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC