A2784 UNIA19082806 Smacat V03 FCC Test Report

FCC ID: 2AUJH-V03

Test Report

Download: PDF
FCCID_4455882

Page 1 of 22 Report No.: UNIA19082806FR-01 FCC RADIO TEST REPORT FCC ID: 2AUJH-V03 Product： Wireless Car Charger Trade Name： N/A Model Name： V03 V01, V02, V04, V05, V06, V07, V08, V09, V10, V11, V12, V13, V14, V15, V16, V17, Serial Model： V18, V19, V20, V21, V22, V23, V24, V25, V26, V27, V28, V29, V30 Report No.： UNIA19082806FR-01 Prepared for Shenzhen Smacat Electronic Technology Co., Ltd. 6th Floor, Building A1, Yangbei Industrial Zone, Huangtian Hangcheng, Baoan, Shenzhen, China Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China

Page 2 of 22 Report No.: UNIA19082806FR-01 TEST RESULT CERTIFICATION Applicant’s name ................. : Shenzhen Smacat Electronic Technology Co., Ltd. 6th Floor, Building A1, Yangbei Industrial Zone, Huangtian Address ................................. : Hangcheng, Baoan, Shenzhen, China Manufacture's Name ............ : Shenzhen Smacat Electronic Technology Co., Ltd. 6th Floor, Building A1, Yangbei Industrial Zone, Huangtian Address ................................. : Hangcheng, Baoan, Shenzhen, China Product description Product name............................... : Wireless Car Charger Trade Mark ............................ : N/A V03, V01, V02, V04, V05, V06, V07, V08, V09, V10, V11, Model and/or type reference : V12, V13, V14, V15, V16, V17, V18, V19, V20, V21, V22, V23, V24, V25, V26, V27, V28, V29, V30 FCC Rules and Regulations Part 15 Subpart C Section 15.209 Standards ............................. : ANSI C63.10: 2013 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test..........................................: Date (s) of performance of tests.............: Aug. 28, 2019 ~ Sep. 10, 2019 Date of Issue ........................................: Sep. 10, 2019 Test Result ............................................: Pass Prepared by: Bob liao/Editor Reviewer: Kahn yang/Supervisor Approved & Authorized Signer: Liuze/Manager

Page 3 of 22 Report No.: UNIA19082806FR-01 Table of Contents Page 1 TEST SUMMARY 4 2 GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 CARRIER FREQUENCY OF CHANNELS 7 2.3 TEST MODE 7 2.4 TEST SETUP 7 2.5 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 8 2.6 MEASUREMENT INSTRUMENTS LIST 9 3 CONDUCTED EMISSION 10 3.1 TEST LIMIT 10 3.2 TEST SETUP 10 3.3 TEST PROCEDURE 11 3.4 TEST RESULT 11 4 RADIATED EMISSION 14 4.1 TEST LIMIT 14 4.2 TEST SETUP 16 4.3 TEST PROCEDURE 17 4.4 TEST RESULT 17 5 ANTENNA REQUIREMENT 20 6 PHOTO OF TEST 21 6.1 RADIATED EMISSION 21 6.2 CONDUCTED EMISSION 22

Page 4 of 22 Report No.: UNIA19082806FR-01 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS ITEM STANGARD RESULT CONDUCTED EMISSION FCC Part 15.207 COMPLIANT RADIATED EMISSION FCC Part 15.209 COMPLIANT ANTENNA REQUIREMENT FCC Part 15.203 COMPLIANT 1.2 TEST FACILITY Test Firm : Shenzhen United Testing Technology Co., Ltd. Address : 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: A2LA Certificate Number: 4747.01 The EMC Laboratory has been accredited by A2LA, and in compliance with ISO/IEC 17025:2017 General Requirements for testing Laboratories. FCC Registration Number: 674885 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. IC Registration Number: 21947 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada.

Page 5 of 22 Report No.: UNIA19082806FR-01 1.3 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. A. Conducted Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 150KHz 2.96 150KHz ~ 30MHz 2.44 B. Radiated Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 30MHz 2.50 30MHz ~ 1000MHz 4.80 1000MHz ~ 6000MHz 4.13

Page 6 of 22 Report No.: UNIA19082806FR-01 2 GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment: Wireless Car Charger Trade Mark: N/A Model Name: V03 V01, V02, V04, V05, V06, V07, V08, V09, V10, V11, V12, Serial No.: V13, V14, V15, V16, V17, V18, V19, V20, V21, V22, V23, V24, V25, V26, V27, V28, V29, V30 All model’s the function, software and electric circuit are the Model Difference: same, only with a product color and model named different. Test sample model: V03. FCC ID: 2AUJH-V03 Antenna Type: Coil Antenna Antenna Gain: 0dBi Operation frequency: 125KHz Number of Channels: 1CH Modulation Type: ASK Battery: DC 3.7V, 60mAh Power Source: DC 5V from adapter with AC 120(240)V/60Hz

Page 7 of 22 Report No.: UNIA19082806FR-01 2.2 CARRIER FREQUENCY OF CHANNELS Channel List Frequency Frequency Frequency Frequency Channel Channel Channel Channel (KHz) (MHz) (MHz) (MHz) 01 125 2.3 TEST MODE The EUT was programmed to be in transmitting mode. Channel List Test Channel Test Frequency (KHz) 01 125 2.4 TEST SETUP Operation of EUT during testing: Adapter EUT Mobile phone

l Nl Page 8 of 22 Report No.: UNIA19082806FR—01 2.5 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. em Equipment Mir/Brand Model/Type No. Note E—1 Wireless Car Charger N/A vO3 EUT E—2 Adapter XIAOMI MDY—08—EF AE Shielded Type Ferrite Core Note: 1. The support equipment was authorized by Declaration of Confirmation. 2. For detachable type /O cable should be specified the length in cm in [LengthJ column. 3. "YES" is means "shielded" "with core"; "NO" is means "unshielded" "without core". lftfmitals—tCSRAS Shenzhen United Testing Technology Co.,Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bac‘an District, Shenzhen, China United Testing Technology(Hong Kong) Limited imellImsz5e Bepe & fhill eRBss m —iH 36552eB RRINRIRR2HR M : 518102 Tel +86—755—86180996 Fax +86—755—86180156 1 http://www.uni—tab hk

Page 9 of 22 Report No.: UNIA19082806FR-01 2.6 MEASUREMENT INSTRUMENTS LIST Item Equipment Manufacturer Model No. Serial No. Calibrated until Conduction Emissions Measurement Conducted Emission 1 EZ-EMC Ver.CCS-3A1-CE N/A N/A Test Software 2 AMN Schwarzbeck NNLK8121 8121370 2020.09.06 3 AMN ETS 3810/2 00020199 2020.09.06 EMI TEST 4 Rohde&Schwarz ESCI 101210 2020.09.06 RECEIVER 5 Pulse limiter CYBRTEK EM5010 E115010056 2020.05.26 6 AAN TESEQ T8-Cat6 38888 2020.09.06 Radiated Emissions Measurement Radiated Emission 1 EZ-EMC Ver.CCS-03A1 N/A N/A Test Software 2 Horn Antenna Sunol DRH-118 A101415 2019.10.08 Broadband Hybrid 3 Sunol JB1 A090215 2019.12.09 Antenna 4 PREAMP HP 8449B 3008A00160 2020.09.06 5 PREAMP HP 8447D 2944A07999 2020.05.26 EMI TEST 6 Rohde&Schwarz ESR3 101891 2020.09.06 RECEIVER VECTOR Signal 7 Rohde&Schwarz SMU200A 101521 2020.09.06 Generator 8 Signal Generator Agilent E4421B MY4335105 2020.09.06 9 MXA Signal Analyzer Agilent N9020A MY50510140 2020.09.06 10 MXA Signal Analyzer Keysight N9020A MY51110104 2020.09.06 11 RF Power sensor DARE RPR3006W 15I00041SNO88 2020.06.09 12 RF Power sensor DARE RPR3006W 15I00041SNO89 2020.06.09 13 RF power divider Anritsu K241B 992289 2020.09.06 Wideband radio 14 Rohde&Schwarz CMW500 154987 2020.09.06 communication tester 15 Active Loop Antenna Com-Power AL-130R 10160009 2020.05.28 Broadband Hybrid 16 Schwarzbeck VULB9163 VULB9163#958 2020.05.28 Antennas 17 Horn Antenna Schwarzbeck BBHA9120D 9120D-1680 2020.05.28 18 Horn Antenna A-INFOMW LB-180400-KF J211060660 2020.05.28 Microwave 19 Broadband Schwarzbeck BBV 9721 100472 2020.05.28 Preamplifier 20 Signal Generator Agilent N5183A MY47420153 2020.05.28 21 Spctrum Analyzer Rohde&Schwarz FSP 40 100501 2020.05.28 22 Power Meter KEYSIGHT N1911A MY50520168 2020.05.28 23 Frequency Meter VICTOR VC2000 997406086 2020.05.28 24 DC Power Source HYELEC HY5020E 055161818 2020.05.28

Page 10 of 22 Report No.: UNIA19082806FR-01 3 CONDUCTED EMISSION 3.1 TEST LIMIT For unintentional device, according to § 15.107(a) Line Conducted Emission Limits is as following Maximum RF Line Voltage (dBV) Frequency CLASS A CLASS B (MHz) Q.P. Ave. Q.P. Ave. 0.15~0.50 79 66 66~56* 56~46* 0.50~5.00 73 60 56 46 5.00~30.0 73 60 60 50 * Decreasing linearly with the logarithm of the frequency. For intentional device, according to §15.207(a) Line Conducted Emission Limit is same as above table. 3.2 TEST SETUP

Page 11 of 22 Report No.: UNIA19082806FR-01 3.3 TEST PROCEDURE 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. The EUT is placed on a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. If a EUT received DC power from the USB Port of Notebook PC, the PC’s adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5. All support equipments received AC power from a second LISN, if any. 6. The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 3.4 TEST RESULT PASS Remark: EUT was tested at AC 120V and 240V, only the worst result of AC 120V was reported.

Page 12 of 22 Report No.: UNIA19082806FR-01 Temperature: 24℃ Relative Humidity: 48% Test Date: Sep. 06, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Line Test Mode: Transmitting mode Remark: Factor = Insertion Loss + Cable Loss, Result = Reading + Factor, Margin = Result – Limit.

Page 13 of 22 Report No.: UNIA19082806FR-01 Temperature: 24℃ Relative Humidity: 48% Test Date: Sep. 06, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Neutral Test Mode: Transmitting mode Remark: Factor = Insertion Loss + Cable Loss, Result = Reading + Factor, Margin = Result – Limit.

LN 4 RADIATED EMISSION Page 14 of 22 Report No.: UNIA19082806FR—01 4.1 TEST LIMIT CFR 47 Part 15, section 15.205 Only spurious emissions are permitted in any of the frequency bands listed the tables in these sections : MHz MHz MHz GHz 0.090—0.110 16.42—16.423 399.9—410 4.5—5.15 \1\ 0.495—0.505 16.69475—16.69525 608—614 5.35—5.46 2.1735—2.1905 16.80425—16.80475 960—1240 7.25—7.75 4.125—4.128 25.5—25.67 1300—1427 8.025—8.5 4.17725—4.17775 37.5—38.25 1435—1626.5 9.0—9.2 4.20725—4.20775 73—74.6 1645.5—1646.5 9.3—9.5 6.215—6.218 74.8—75.2 1660—1710 10.6—12.7 6.26775—6.26825 108—121.94 1718.8—1722.2 13.25—13.4 6.31175—6.31225 123—138 2200—2300 14.47—14.5 8.291—8.294 149.9—150.05 2310—2390 15.35—16.2 8.362—8.366 156.52475—156.52523 2483.5—2500 17.7—21.4 8.37625—8.38675 156.7—156.9 2690—2900 22.01—23.12 8.41425—8.41475 162.0125—167.17 3260—3267 23.6—24.0 12.29—12.293. 167.72—173.2 3332—3339 31.2—31.8 12.51975—12.52025 240—285 3345.8—3358 36.43—36.5 12.57675—12.57723 322—3354 3600—4400 (23) 13.36—13.41 CFR 47 Part 15, section 15.209 The emissions from an intentional radiator shall not exceed the limits in the tables in these sections using an average detector: Frequency Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009—0.490 2400/F (kHz) 300 0.490—1.705 24000/F(kHz) 30 1.705—30.0 30 30 30—88 100** 3 88a—216 150** 3 216—960 200** 3 Above 960 500 3 lftfmitals—tCSRAS Shenzhen United Testing Technology Co.,Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bac‘an District, Shenzhen, China United Testing Technology(Hong Kong) Limited imallImszgeBepe&fhillisBssm—iH36559eBRRINRIRR2NR M : 518102 Tel : +86—755—86180996 Fax +86—755—86180156 I http://www.uni—lab hk

Page 15 of 22 Report No.: UNIA19082806FR-01 CFR 47 Part 15, section 15.35 When average radiated emission measurements are specified, the limit on the peak level of the radio Frequency emission is 20dB above the maximum permitted average emission limit. Transmitter Spurious Emissions 9KHz-30MHz 9-150KHz 150-490KHz 490KHz-30MHz Resolution Bandwidth 200Hz 9KHz 9KHz Video Bandwidth 2KHz 100KHz 100KHz Detector Peak Peak Peak Trace Mode Max Hold Max Hold Max Hold Sweep Time Auto Auto Auto

Page 16 of 22 Report No.: UNIA19082806FR-01 4.2 TEST SETUP 1. Radiated Emission Test-Up Frequency Below 30MHz 2. Radiated Emission Test-Up Frequency 30MHz~1GHz

Page 17 of 22 Report No.: UNIA19082806FR-01 4.3 TEST PROCEDURE 1. Measurement distance is 3m. 2. For the measurement range up to 30MHz in the following plots the field strength result from 3m. 3. Distance measurement are extrapolated to 300m and 30m distance respectively, by 40dB/decade. According to part 15.31(f)(2), per antenna factor scaling. 4. Measurements below 1000MHz are performed with a peak detector and compared to average limits. Measurements with an average detector are not required. Note: For battery operated equipment, the equipment tests shall be performed using a new battery. 4.4 TEST RESULT PASS For 9KHz-30MHz Test Results: Detector Frequency Reading Actual FS Limits 3m Margin Mode Factor (dB) (MHz) (dBuV) (dBuV/m) (dBuV/m) (dBuV/m) (PK/QP) 0.125 PK 70.66 15.48 86.14 105.67 -19.53 0.820 PK 31.93 16.20 48.13 69.33 -21.20 1.625 PK 24.50 16.24 40.74 63.39 -22.65 2.277 PK 31.96 15.18 47.14 69.50 -22.36 3.002 PK 31.08 15.60 46.68 69.50 -22.82 8.206 PK 30.24 15.50 45.74 69.50 -23.76

Page 18 of 22 Report No.: UNIA19082806FR-01 For 30MHz-1GHz Test Results: Temperature: 24℃ Relative Humidity: 48% Test Date: Sep. 06, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Horizontal Test Mode: Transmitting mode Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level – Limit Factor = Ant. Factor + Cable Loss – Pre-amplifier

LN Page 19 of 22 Report No.: UNIA19082806FR—01 Temperature: 24°C Relative Humidity: 48% Test Date: Sep. 06, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Vertical Test Mode: Transmitting mode 80.0 dBu¥/m Limit: — Margin: _ —12—'34—55 20 —40 30.000 40 50 o 70 80 (MHz) 300 400 500 600 700 1000.000 No. Frequency Reading Correction Result Limit Margin Degree Height Remark (MHz) (dBuV) _|factor(dB/m)| (dBuV/im)_| (dBuV/im) (dB) (deg.) (cm) 1* 30.1054 37.84 —6.75 31.09 40.00 —8.91 205 100 peak 2 99.8777 48.13 41717 30.96 43.50 1254 60 100 peak 3 258.3264 43.72 —14.96 28.76 46.00 ~17.24 80 100 peak 4 322.1886 39.67 1213 27.54 46.00 ~18.46 155 100 peak 5 580.7026 40.78 —8.36 32.42 46.00 1358 20 100 peak 6 665.8035 38.56 —6.34 32.22 46.00 ~13.78 85 100 peak Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level — Limit Factor= Ant. Factor + Cable Loss — Pre—amplifier Remark: 1. Measuring frequencies from 9 KHz to the 1 GHz, Radiated emission test from 9KHz to 30MHzwas verified, and no any emission was found except system noise floor. 2.* denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. 3. The IF bandwidth of EMI Test Receiver between 30MHz to 1 GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz. olbOtmitnIHANSGIRAS Shenzhen United Testing Technology Co.,Ltd. | 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bac‘an District, Shenzhen, China United Testing Technology(Hong Kong) Limited imIems5ee9e2 ltXeBXsP—Is365920BLIEFESEE2NE MR : 518102 Tel +86—755—86180996 Fax +86—755—86180156 http: // ww w.uni—lab.hik

Page 20 of 22 Report No.: UNIA19082806FR-01 5 ANTENNA REQUIREMENT Standard Applicable: For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Antenna Connected Construction: The antenna used in this product is a Coil Antenna, The directional gains of antenna used for transmitting is 0dBi. ANTENNA:

Page 21 of 22 Report No.: UNIA19082806FR-01 6 PHOTO OF TEST 6.1 RADIATED EMISSION

Page 22 of 22 Report No.: UNIA19082806FR-01 6.2 CONDUCTED EMISSION ***End of Report***


Document Created: 2019-09-25 01:24:46
Document Modified: 2019-09-25 01:24:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC