Test Report DSS part2

FCC ID: 2ATS9-7128

Test Report

Download: PDF
FCCID_4425666

Report No.: AGC08506190701FE03 Page 45 of 63 EUT WIRELESS HEADPHONE Model Name ENDURO 100 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4960.022 49.23 0.22 49.45 74.00 -24.55 peak 4960.022 46.45 0.22 46.67 54.00 -7.33 AVG 7440.033 37.84 2.64 40.48 74.00 -33.52 peak 7440.033 35.68 2.64 38.32 54.00 -15.68 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. EUT WIRELESS HEADPHONE Model Name ENDURO 100 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4960.022 48.36 0.22 48.58 74.00 -25.42 peak 4960.022 45.11 0.22 45.33 54.00 -8.67 AVG 7440.033 39.24 2.64 41.88 74.00 -32.12 peak 7440.033 34.97 2.64 37.61 54.00 -16.39 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. RESULT: PASS Note: Other emissions from 1G to 25 GHz are considered as ambient noise. No recording in the test report. Factor = Antenna Factor + Cable loss - Amplifier gain, Over=Measure-Limit. The “Factor” value can be calculated automatically by software of measurement system. All test modes had been tested. The GFSK modulation is the worst case and recorded in the report.

Report No.: AGC08506190701FE03 Page 46 of 63 TEST RESULT FOR RESTRICTED BANDS REQUIREMENTS EUT WIRELESS HEADPHONE Model Name ENDURO 100 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Horizontal PK AV RESULT: PASS

Report No.: AGC08506190701FE03 Page 47 of 63 EUT WIRELESS HEADPHONE Model Name ENDURO 100 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Vertical PK AV RESULT: PASS

Report No.: AGC08506190701FE03 Page 48 of 63 EUT WIRELESS HEADPHONE Model Name ENDURO 100 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal PK AV RESULT: PASS

Report No.: AGC08506190701FE03 Page 49 of 63 EUT WIRELESS HEADPHONE Model Name ENDURO 100 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical PK AV RESULT: PASS Note: The factor had been edited in the “Input Correction” of the Spectrum Analyzer. So the Amplitude of test plots is equal to Reading level plus the Factor in dB. Use the A dB(μV) to represent the Amplitude. Use the F dB(μV/m) to represent the Field Strength. So A=F. All test modes had been pre-tested. The GFSK modulation is the worst case and recorded in the report.

Report No.: AGC08506190701FE03 Page 50 of 63 11. NUMBER OF HOPPING FREQUENCY 11.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: The frequency band of operation. Depending on the number of channels the device supports, it may be necessary to divide the frequency range of operation across multiple spans, to allow the individual channels to be clearly seen. 2. RBW: To identify clearly the individual channels, set the RBW to less than 30% of the channel spacing or the 20 dB bandwidth, whichever is smaller. 3. VBW ≥ RBW. Sweep: Auto. Detector function: Peak. Trace: Max hold. 4. Allow the trace to stabilize. 11.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 8.2 11.3. MEASUREMENT EQUIPMENT USED The same as described in section 6 11.4. LIMITS AND MEASUREMENT RESULT MEASUREMENT TOTAL NO. OF LIMIT (NO. OF CH) RESULT (NO. OF CH) HOPPING CHANNEL >=15 79 PASS TEST PLOT FOR NO. OF TOTAL CHANNELS Note: The GFSK modulation is the worst case and recorded in the report.

Report No.: AGC08506190701FE03 Page 51 of 63 12. TIME OF OCCUPANCY (DWELL TIME) 12.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Zero span, centered on a hopping channel. 2. RBW shall be≤channel spacing and where possible RBW should be set >> 1 / T, where T is the expected dwell time per channel. 3. Sweep: As necessary to capture the entire dwell time per hopping channel; where possible use a video trigger and trigger delay so that the transmitted signal starts a little to the right of the start of the plot. The trigger level might need slight adjustment to prevent triggering when the system hops on an adjacent channel; a second plot might be needed with a longer sweep time to show two successive hops on a channel. 4. Detector function: Peak. Trace: Max hold. 5. Use the marker-delta function to determine the transmit time per hop. 6. Repeat the measurement using a longer sweep time to determine the number of hops over the period specified in the requirements. The sweep time shall be equal to, or less than, the period specified in the requirements. Determine the number of hops over the sweep time and calculate the total number of hops in the period specified in the requirements, using the following equation: (Number of hops in the period specified in the requirements) = (number of hops on spectrum analyzer) × (period specified in the requirements / analyzer sweep time) 7. The average time of occupancy is calculated from the transmit time per hop multiplied by the number of hops in the period specified in the requirements. 12.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 8.2 12.3. MEASUREMENT EQUIPMENT USED The same as described in section 6 12.4. LIMITS AND MEASUREMENT RESULT Time of Pulse Number of hops in the period Sweep Time Limit Channel for DH5 specified in the requirements (ms) (ms) (ms) Low 2.876 27*4 310.61 400 Middle 2.876 27*4 310.61 400 High 2.880 27*4 311.04 400 Note: The 8-DPSK modulation is the worst case and recorded in the report.

Report No.: AGC08506190701FE03 Page 52 of 63 TEST PLOT OF LOW CHANNEL

Report No.: AGC08506190701FE03 Page 53 of 63 TEST PLOT OF MIDDLE CHANNEL

Report No.: AGC08506190701FE03 Page 54 of 63 TEST PLOT OF HIGH CHANNEL

Report No.: AGC08506190701FE03 Page 55 of 63 13. FREQUENCY SEPARATION 13.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Wide enough to capture the peaks of two adjacent channels. 2. RBW: Start with the RBW set to approximately 30% of the channel spacing; adjust as necessary to best identify the center of each individual channel. 3. Video (or average) bandwidth (VBW) ≥ RBW. 4. Sweep: Auto. e) Detector function: Peak. f) Trace: Max hold. g) Allow the trace to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. 13.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 6.2 13.3. MEASUREMENT EQUIPMENT USED The same as described in section 6.3 13.4. LIMITS AND MEASUREMENT RESULT CHANNEL LIMIT RESULT CHANNEL SEPARATION KHz KHz Pass CH01-CH02 1001 >=25 KHz or 2/3 20 dB BW TEST PLOT FOR FREQUENCY SEPARATION Note: The 8-DPSK modulation is the worst case and recorded in the report.

Report No.: AGC08506190701FE03 Page 56 of 63 APPENDIX A: PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ

Report No.: AGC08506190701FE03 Page 57 of 63 APPENDIX B: PHOTOGRAPHS OF EUT ALL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC08506190701FE03 Page 58 of 63 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC08506190701FE03 Page 59 of 63 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC08506190701FE03 Page 60 of 63 RIGHT VIEW OF EUT OPEN VIEW OF EUT-1

Report No.: AGC08506190701FE03 Page 61 of 63 OPEN VIEW OF EUT-2 INTERNAL VIEW OF EUT-1

Report No.: AGC08506190701FE03 Page 62 of 63 INTERNAL VIEW OF EUT-2 BT ANTENNA INTERNAL VIEW OF EUT-3

Report No.: AGC08506190701FE03 Page 63 of 63 INTERNAL VIEW OF EUT-4 ----END OF REPORT----


Document Created: 2019-09-02 23:07:03
Document Modified: 2019-09-02 23:07:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC