user manual

FCC ID: 2ASV6-T6

Users Manual

Download: PDF
FCCID_4482682

Walkie—talkie serore use Functions at Glance Removing the belt cllp Before Inscrt baterlesInto the device, Aist pullthe ho lp latth avay from User Manual the devte Volume (short press) Channel Call Button on (short press) (long press)

Installing the Batteries a. Sending a call tone 9. Technlcal specifications Press the CALL button, the call tone will be transmitted on the setting Frequency 445.00625MHz~446.5625MHz 1. Slid down the battery compartment cover. channel. 462.5625MHz~462.6625MHz 2. Insert 3* AAA Alkaline Battery (Not included) 5.. Battery saving function Channel 3 channels 3. Position the batteries according to the polarity marking on the battery When the device has not been used for 6 seconds, the econony mode is Transmission Power <0.5W compartment. automatically acthated. This does not affect the reception of transmission and Range Up to 5 Km in open field 4. After placing batteriesinto correct postions, put the battery cover back on. the standby mode is automatically re—activated as soon as a signal is detected. Battery type 3* AAA Alkaline/rechargeable batteries (DC+.5V) Using the device 6. Bult—In Flashlight The battery valtage: 1.5V Your device has a buit—in flashlight that can be use in sending light signals Madulation type rorse 1. Turning the device on/off 1 or for ourlighting needs. a. Switch on the device: short Press the ©. button then you will hear a 7. Low battery swiltch off Channel spacing 12.5 kiz (Narrowband) beep sound. 1 When low battery level is detected, the waltie talkis will beep twice and shut b. Sitch off the device: Long Press the O button 3 seconds then you will down hear a beep sound. 8. Chaiging 10. Transmlt and Recelve Procedure 2. Recelving/transmitting communications: Plug i the charger Your two—way rado contains a transmitter and a recelver. To control your The devices are in "Reception" mode when it is turned ON and no The LED indicator willbegin toflash. exposure and ensure complance with the general population/uncontrolled transmittng. Indicates that charging is n progress. environment exposure limits, always adhere to the following procedure: When you press the PTT (push to talk) button, the device switches to After being fully charged, «Tansmit no more than 50% of the time. To recelve cals, release the PTT "Transmission" mode. LED stops flashing button. To transmit (talk), press the Push to Talk (PTT) button. Transmitting Hold the device in a vertical position with the MIC (microphone) 3—5 cm away 50% of the time, or less,is important because the radio Generates measurable from your mouth. While holding the PTT button, speakinto the microphone in a RF energy exposure only when transmitting (in terms of measuring standards normal tone of voice. complance). Release the PTT button when you have finished transmiting. «Abays hold the radio approximately Sm in front of your mouth with the For others to receive your transmission, they must be on the same channel antenna pointing away from your head. with you. Note: Charger specification 1. The talking range depends on tettain and weather conditions. It will be affected by obstructions such as hill, bush or buildings. microU$B DC : 5V +/—0.2V 2. Don‘t ty to use two devices which are less than 1.5m (5 feet) apait. Otherwise, you may experience interference. 1000mA 3. Changing Channels Press and hold the channel button for 3 seconds to change the channel.

FCC Statement 11. Channel and Frequency (MHz) This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. RF Exposure Warning This equipment must be installed and operated in accordance with provided instructions and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. The SAR limit adopted by US is 1.6 W/kg averaged over 1 grams of tissue. The highest SAR value for this device type when properly worn on the body is 0.19 W/kg.


Document Created: 2019-10-17 12:11:20
Document Modified: 2019-10-17 12:11:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC