test report

FCC ID: 2AS7VGS-BH918

Test Report

Download: PDF
FCCID_4263900

Report No.: AGC0O0806190403FEO3 GC T KA 1 iH Page 46 of 62 Attestatlonof Global Compliance TEST PLOT OF LOW CHANNEL Fu Keys\ghtSpectrumAna\yzEr Swept 5A |i”i|\él 509 aC |__SenSe:mNT] | ALTGN AUTO ___|01:15:50 PM Apr24, 2019 Marker T 2 87843 ms . Avg Type: Log—Pwr PNO: Fast +»— TTig: FreeRun IFGain:Low Atten: 20 dB Select Marker > 1 10 dB!dlv Ref 10.00 dBm ppmeell Normal mm Delta mm FixedD nc Off euuponmessimen| Properties»> I . ib a| nalplesiel omm——mm Center 2402000000 GHz E6U e More Res BW 1.0 MHz #VBW 3.0 MHz Sweep 10.00 ms (30000 pts E STATUS Fu Keysight Spectrum Analyzer — SweptSA |i”i|\él |__SenSe:mNT] | ALTGN AUTO ___|O119:13 PMA Avg Type: Log—Pwr PNO: Fast —»— TTig: FreeRun IFGain:Low Atten: 20 dB Auto Tune 10 dB!dnr Ref 10.00 dBm CenterFreq 2.402000000 GHz StartFreq 2.402000000 GHz Stop Freq 2.402000000 GHz ultI * 1000000 MHz Freq Offset 0 Hz Center 2402000000 GHz E6U e Res BW 1.0 MHz #VBW 3.0 MHz Sweep 7.902 s (30000 pts) msc STATUS The results shbwuivin thisftestreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/AGC, this docufgeht cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed Athittp://www.agc@eit.com. Attestatiqitof Global Compliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00806190403FE03 Page 47 of 62 TEST PLOT OF MIDDLE CHANNEL

Report No.: AGC00806190403FE03 Page 48 of 62 TEST PLOT OF HIGH CHANNEL

Report No.: AGC00806190403FE03 Page 49 of 62 13. FREQUENCY SEPARATION 13.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Wide enough to capture the peaks of two adjacent channels. 2. RBW: Start with the RBW set to approximately 30% of the channel spacing; adjust as necessary to best identify the center of each individual channel. 3. Video (or average) bandwidth (VBW) ≥ RBW. 4. Sweep: Auto. e) Detector function: Peak. f) Trace: Max hold. g) Allow the trace to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. 13.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 6.2 13.3. MEASUREMENT EQUIPMENT USED The same as described in section 6.3 13.4. LIMITS AND MEASUREMENT RESULT CHANNEL LIMIT RESULT CHANNEL SEPARATION KHz KHz Pass CH01-CH02 10001 >=25 KHz or 2/3 20 dB BW TEST PLOT FOR FREQUENCY SEPARATION Note: The π /4-DQPSK modulation is the worst case and recorded in the report.

Report No.: AGC00806190403FE03 Page 50 of 62 14. FCC LINE CONDUCTED EMISSION TEST 14.1. LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz~500kHz 66-56 56-46 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz. 14.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST EUT & Support Units

Report No.: AGC00806190403FE03 Page 51 of 62 14.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. All support equipments received AC120V/60Hz power from a LISN, if any. 5. The EUT received DC 15V power from adapter which received AC120V/60Hz power from a LISN. 6. The test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. 9. The test mode(s) were scanned during the preliminary test. Then, the EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing. 14.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. EUT and support equipment was set up on the test bench as per step 2 of the preliminary test. 2. A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. 3. The test data of the worst case condition(s) was reported on the Summary Data page.

Report No.: AGC00806190403FE03 Page 52 of 62 14.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST Line Conducted Emission Test Line 1-L

Report No.: AGC00806190403FE03 Page 53 of 62 Line Conducted Emission Test Line 2-N RESULT: PASS Note: All the test modes had been tested, the mode 1 was the worst case. Only the data of the worst case would be record in this test report.

Report No.: AGC00806190403FE03 Page 54 of 62 APPENDIX A: PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ

Report No.: AGC00806190403FE03 Page 55 of 62 CONDUCTED EMISSION TEST SETUP

Report No.: AGC00806190403FE03 Page 56 of 62 APPENDIX B: PHOTOGRAPHS OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT

Report No.: AGC00806190403FE03 Page 57 of 62 FRONT VIEW OF EUT BACK VIEW OF EUT

Report No.: AGC00806190403FE03 Page 58 of 62 LEFT VIEW OF EUT RIGHT VIEW OF EUT

Report No.: AGC00806190403FE03 Page 59 of 62 VIEW OF-1 EUT (PORT) OPEN VIEW OF EUT

Report No.: AGC00806190403FE03 Page 60 of 62 VIEW OF BATTERY INTERNAL VIEW OF EUT-1 Antenna

Report No.: AGC00806190403FE03 Page 61 of 62 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3

Report No.: AGC00806190403FE03 Page 62 of 62 INTERNAL VIEW OF EUT-4 ----END OF REPORT----


Document Created: 2019-05-06 12:24:34
Document Modified: 2019-05-06 12:24:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC