BSL190111991301RF-1

FCC ID: 2AS6M-TT-1203

Test Report

Download: PDF
FCCID_4262931

BSL Testing Co.,LTD. Report No.: BSL190111991301RF FCC Part 15C Measurement and Test Report For InterEdge Technologies,LLC FCC ID: 2AS6M-TT-1203 FCC Rule(s): FCC Part 15.247 Product Description: Temperature-Tracker Tested Model: TT-1203 Report No.: BSL190111991301RF Tested Date: March 20- 28, 2019 Issued Date: March 28, 2019 Tested By: Messi Wang / Engineer Reviewed By: Lisa. Ji / EMC Manager Approved & Authorized By: Mike mo / PSQ Manager Prepared By: BSL Testing Co.,LTD. NO. 24, ZH Park, Nantou, Shenzhen, 518000 China Tel: 400-882-9628 Fax: 86- 755-26508703 Report No.: BSL11505901RF Page 1 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF TABLE OF CONTENTS 1. GENERAL INFORMATION.................................................................................................................................... 3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT).............................................................................. 3 1.2 TEST STANDARDS................................................................................................................................................... 4 1.3 TEST METHODOLOGY............................................................................................................................................. 4 1.4 TEST FACILITY........................................................................................................................................................ 4 1.5 EUT SETUP AND TEST MODE................................................................................................................................. 5 1.6 MEASUREMENT UNCERTAINTY...............................................................................................................................5 1.7 TEST EQUIPMENT LIST AND DETAILS..................................................................................................................... 6 2. SUMMARY OF TEST RESULTS............................................................................................................................ 7 3. RF EXPOSURE.......................................................................................................................................................... 8 3.1 STANDARD APPLICABLE......................................................................................................................................... 8 3.2 TEST RESULT.......................................................................................................................................................... 8 4. ANTENNA REQUIREMENT................................................................................................................................... 9 4.1 STANDARD APPLICABLE......................................................................................................................................... 9 4.2 EVALUATION INFORMATION................................................................................................................................... 9 5. POWER SPECTRAL DENSITY............................................................................................................................ 10 5.1 STANDARD APPLICABLE....................................................................................................................................... 10 5.2 TEST PROCEDURE..................................................................................................................................................10 5.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................10 5.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 10 6. 6DB BANDWIDTH.................................................................................................................................................. 13 6.1 STANDARD APPLICABLE....................................................................................................................................... 13 6.2 TEST PROCEDURE..................................................................................................................................................13 6.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................13 6.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 13 7. RF OUTPUT POWER............................................................................................................................................. 16 7.1 STANDARD APPLICABLE....................................................................................................................................... 16 7.2 TEST PROCEDURE..................................................................................................................................................16 7.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................16 7.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 16 8. FIELD STRENGTH OF SPURIOUS EMISSIONS.............................................................................................. 19 8.1 STANDARD APPLICABLE....................................................................................................................................... 19 8.2 TEST PROCEDURE..................................................................................................................................................19 8.3 CORRECTED AMPLITUDE & MARGIN CALCULATION........................................................................................... 21 8.4 ENVIRONMENTAL CONDITIONS.............................................................................................................................21 8.5 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 21 9. OUT OF BAND EMISSIONS..................................................................................................................................27 9.1 STANDARD APPLICABLE....................................................................................................................................... 27 9.2 TEST PROCEDURE..................................................................................................................................................27 9.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................28 9.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 28 10. CONDUCTED EMISSIONS..................................................................................................................................30 10.1 TEST PROCEDURE................................................................................................................................................30 10.2 BASIC TEST SETUP BLOCK DIAGRAM.................................................................................................................30 10.3 ENVIRONMENTAL CONDITIONS...........................................................................................................................30 10.4 TEST RECEIVER SETUP........................................................................................................................................31 10.5 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................. 31 10.6 CONDUCTED EMISSIONS TEST DATA..................................................................................................................31 Report No.: BSL11505901RF Page 2 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Applicant: InterEdge Technologies,LLC Address of applicant: 3268 San Jose St,Clearwater FL 33759-USA Manufacturer: ZE Mfg Services Sdn Bhd Address of manufacturer: Plot85C,Lintang Bayan Lepas9,Bayan Lepas Industrial Park4,Bayan Lepas 11900 Penang.Malaysia General Description of EUT Product Name: Temperature-Tracker Brand Name: Temperature-Tracker Model No.: TT-1203 Rated Voltage: DC 3.0V by Battery Adapter Information: N/A Note: The test data is gathered from a production sample provided by the manufacturer. Technical Characteristics of EUT Bluetooth Version: V4.1 Frequency Range: 2402-2480MHz RF Output Power: -1.59dBm (Conducted) Modulation: GFSK Quantity of Channels: 40 Channel Separation: 2MHz Type of Antenna: Ceramic antenna Antenna Gain: 0dBi Lowest Internal Frequency: 32.768KHz Report No.: BSL11505901RF Page 3 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 1.2 Test Standards The following report is prepared on behalf of the InterEdge Technologies,LLC in accordance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 of the Federal Communication Commissions rules. The objective is to determine compliance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 of the Federal Communication Commissions rules. Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product, which result in lowering the emission, should be checked to ensure compliance has been maintained. 1.3 Test Methodology All measurements contained in this report were conducted with ANSI C63.10-2013, American National Standard for Testing Unlicensed Wireless Devices, and ANSI C63.4-2014, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. The measurement guide KDB 558074 D01 v05 for digital transmission systems shall be performed also. 1.4 Test Facility BSL Testing Co.,LTD. NO. 24, ZH Park, Nantou, Shenzhen, 518000 China Designation Number : CN1217 Test Firm Registration Number: 866035 Tel: 86- 755-26508703 Fax: 86- 755-26508703 Report No.: BSL11505901RF Page 4 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 1.5 EUT Setup and Test Mode The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. All testing shall be performed under maximum output power condition, and to measure its highest possible emissions level, more detailed description as follows: Test Mode List Test Mode Description Remark TM1 Battery:GFSK(BLE) 2402MHz, 2442MHz, 2480MHz EUT Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite Special Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite / / / / Auxiliary Equipment List and Details Description Manufacturer Model Serial Number PC Lenovo Lenovo B490 BSTSZEMC-77 1.6 Measurement Uncertainty Measurement uncertainty Parameter Conditions Uncertainty RF Output Power Conducted ±0.42dB Occupied Bandwidth Conducted ±1.5% Power Spectral Density Conducted ±1.8dB Conducted Spurious Emission Conducted ±2.17dB Conducted Emissions Conducted ±2.88dB Transmitter Spurious Emissions Radiated ±5.1dB Report No.: BSL11505901RF Page 5 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 1.7 Test Equipment List and Details Description Manufacturer Model Serial No. Cal Date Due. Date Communication Tester Rohde & Schwarz CMW500 100358 2018-11-08 2019-11-07 Spectrum Analyzer R&S FSP40 100550 2018-10-08 2019-10-07 Test Receiver R&S ESCI7 US47140102 2018-10-08 2019-10-07 Signal Generator HP 83630B 3844A01028 2018-10-08 2019-10-07 Test Receiver R&S ESPI-3 100180 2018-10-08 2019-10-07 Amplifier Agilent 8449B 4035A00116 2018-10-08 2019-10-07 Amplifier HP 8447E 2945A02770 2018-10-08 2019-10-07 Signal Generator IFR 2023A 202307/242 2018-10-08 2019-10-07 Broadband Antenna SCHAFFNER 2774 2774 2018-10-21 2019-10-20 Biconical and log ELECTRO-METRI EM-6917B-1 171 2018-10-21 2019-10-20 periodic antennas CS Horn Antenna R&S HF906 100253 2018-10-21 2019-10-20 Horn Antenna EM EM-6961 6462 2018-10-21 2019-10-20 LISN R&S ESH3-Z5 100196 2018-10-08 2019-10-07 LISN COM-POWER LI-115 02027 2018-10-08 2019-10-07 3m Semi-Anechoic Chengyu Electron 9 (L)*6 (W)* 6 (H) BSL086 2018-10-08 2019-10-07 Chamber Horn Antenna Schwarzbeck BBHA9170 00814 2018-10-21 2019-10-20 Loop Antenna Schwarz beck FMZB 1519B 9773 2018-10-21 2019-10-20 power meter DARE RPR3006W 15I00041SNO03 2018-10-21 2019-10-20 Report No.: BSL11505901RF Page 6 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 2. SUMMARY OF TEST RESULTS FCC Rules Description of Test Item Result § 2.1093 RF Exposure PASS §15.203;§15.247(b)(4)(i) Antenna Requirement PASS §15.205 Restricted Band of Operation PASS §15.207(a) Conducted Emission N/A §15.247(e) Power Spectral Density PASS §15.247(a)(2) 6 dB Bandwidth PASS §15.247(b)(3) RF Output Power PASS §15.209(a) Radiated Emission PASS §15.247(d) Band Edge (Out of Band Emissions) PASS Note: PASS: applicable, N/A: not applicable. Report No.: BSL11505901RF Page 7 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 3. RF Exposure 3.1 Standard Applicable According to§1.1307 and §2.1093, the portable transmitter must comply the RF exposure requirements. 3.2 Test Result This product complied with the requirement of the RF exposure, please see the RF Exposure Report. Report No.: BSL11505901RF Page 8 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 4. Antenna Requirement 4.1 Standard Applicable According to FCC Part 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. 4.2 Evaluation Information This product has a Ceramic antenna, fulfill the requirement of this section. Report No.: BSL11505901RF Page 9 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 5. Power Spectral Density 5.1 Standard Applicable According to 15.247(a)(1)(iii), For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. 5.2 Test Procedure According to the KDB 558074 D01 v05, the test method of power spectral density as below: a) Set analyzer center frequency to DTS channel center frequency. b) Set the span to 1.5 times the DTS bandwidth. c) Set the RBW to: 3 kHz ≤ RBW ≤ 100 kHz. d) Set the VBW ≥ 3 × RBW. e) Detector = peak. f) Sweep time = auto couple. g) Trace mode = max hold. h) Allow trace to fully stabilize. i) Use the peak marker function to determine the maximum amplitude level within the RBW. j) If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. 5.3 Environmental Conditions Temperature: 26 C Relative Humidity: 54 ATM Pressure: 1011 mbar 5.4 Summary of Test Results/Plots Just only show the worst case Test Channel Power Spectral Density Limit Test Mode MHz dBm/3kHz dBm/3kHz 2402 -20.27 8 GFSK(BLE) 2442 -17.69 8 2480 -17.77 8 Please refer to the following test plots: Report No.: BSL11505901RF Page 10 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF Low Channel * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -20.27 dBm Ref 11 dBm * Att 30 dB SWT 225 ms 2.402012000 GHz 10 Offset 1 dB A 0 1 PK MAXH -10 LVL 1 -20 -30 -40 3DB -50 -60 -70 -80 Center 2.402 GHz 200 kHz/ Span 2 MHz Middle Channel Date: 28.JAN.2019 14:41:28 * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -17.69 dBm Ref 11 dBm * Att 30 dB SWT 225 ms 2.442012000 GHz 10 Offset 1 dB A 0 1 PK VIEW -10 LVL 1 -20 -30 -40 3DB -50 -60 -70 -80 Center 2.442 GHz 200 kHz/ Span 2 MHz Date: 28.JAN.2019 14:44:14 Report No.: BSL11505901RF Page 11 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF High Channel * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -17.77 dBm Ref 11 dBm * Att 30 dB SWT 225 ms 2.480012000 GHz 10 Offset 1 dB A 0 1 PK VIEW -10 LVL 1 -20 -30 -40 3DB -50 -60 -70 -80 Center 2.48 GHz 200 kHz/ Span 2 MHz Date: 28.JAN.2019 14:46:36 Report No.: BSL11505901RF Page 12 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 6. 6dB Bandwidth 6.1 Standard Applicable According to 15.247(a)(2). Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 6.2 Test Procedure a) Set RBW = 100 kHz. b) Set the video bandwidth (VBW) ≥ 3 × RBW. c) Detector = Peak. d) Trace mode = max hold. e) Sweep = auto couple. f) Allow the trace to stabilize. g) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. 6.3 Environmental Conditions Temperature: 25 C Relative Humidity: 53 ATM Pressure: 1018 mbar 6.4 Summary of Test Results/Plots Just only show the worst case Test Channel 6 dB Bandwidth Limit Test Mode MHz kHz kHz 2402 720 ≥500 GFSK(BLE) 2442 708 ≥500 2480 714 ≥500 Please refer to the following test plots: Report No.: BSL11505901RF Page 13 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF For BLE Low Channel: * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -5.07 dBm Ref 11 dBm * Att 30 dB SWT 2.5 ms 2.402018000 GHz 10 Offset 1 dB Marker 1 [T1 ] -11.61 dBm 2.401640000 GHz A 0 2 Delta 1 [T1 ] 1 PK 0.70 dB VIEW 1 1 720.000000000 kHz LVL -10 D1 -11.07 dBm -20 -30 -40 3DB -50 -60 -70 -80 Center 2.402 GHz 300 kHz/ Span 3 MHz Middle Channel: * RBW 100 kHz Marker 2 [T1 ] Date: 28.JAN.2019 14:51:20 * VBW 300 kHz -2.78 dBm Ref 11 dBm * Att 30 dB SWT 2.5 ms 2.442018000 GHz 10 Offset 1 dB Marker 1 [T1 ] -9.01 dBm 2.441646000 GHz A 0 2 Delta 1 [T1 ] 1 PK 1 1 0.72 dB VIEW D1 -8.78 dBm 708.000000000 kHz LVL -10 -20 -30 -40 3DB -50 -60 -70 -80 Center 2.442 GHz 300 kHz/ Span 3 MHz Date: 28.JAN.2019 15:24:54 Report No.: BSL11505901RF Page 14 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF High Channel: * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -2.32 dBm Ref 11 dBm * Att 30 dB SWT 2.5 ms 2.480024000 GHz 10 Offset 1 dB Marker 1 [T1 ] -8.79 dBm 2.479646000 GHz A 0 2 Delta 1 [T1 ] 1 PK 1 1 0.88 dB VIEW D1 -8.32 dBm -10 714.000000000 kHz LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.48 GHz 300 kHz/ Span 3 MHz Date: 29.JAN.2019 07:34:20 Report No.: BSL11505901RF Page 15 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 7. RF Output Power 7.1 Standard Applicable According to 15.247(b)(3). For systems using digital modulation in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands: 1 Watt. 7.2 Test Procedure According to section KDB-558074 D01 v05 section 9.1.1, this procedure shall be used when the measurement instrument has available a resolution bandwidth that is greater than the DTS bandwidth. a) Set the RBW ≥ DTS bandwidth. b) Set VBW ≥ 3 × RBW. c) Set span ≥ 3 x RBW d) Sweep time = auto couple. e) Detector = peak. f) Trace mode = max hold. g) Allow trace to fully stabilize. h) Use peak marker function to determine the peak amplitude level. 7.3 Environmental Conditions Temperature: 26 C Relative Humidity: 57 ATM Pressure: 1011 mbar 7.4 Summary of Test Results/Plots Just only show the worst case Frequency Reading Output Power Limit Test Mode MHz dBm mW mW 2402 -4.24 0.3767 1000 GFSK(BLE) 2442 -2.13 0.6124 1000 2480 -1.59 0.6934 1000 Note: the antenna gain of 0.5dBi less than 6dBi maximum permission antenna gain value based on 1 watt peak output power limit. Report No.: BSL11505901RF Page 16 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF For BLE: Low Channel: * RBW 3 MHz Marker 1 [T1 ] * VBW 3 MHz -4.24 dBm Ref 11 dBm * Att 30 dB SWT 2.5 ms 2.402468000 GHz 10 Offset 1 dB A 0 1 1 PK VIEW -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.402 GHz 900 kHz/ Span 9 MHz Middle Channel: * RBW 3 MHz Marker 1 [T1 ] Date: 29.JAN.2019 07:41:24 * VBW 3 MHz -2.13 dBm Ref 11 dBm * Att 30 dB SWT 2.5 ms 2.442000000 GHz 10 Offset 1 dB A 0 1 1 PK VIEW -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.442 GHz 900 kHz/ Span 9 MHz Date: 29.JAN.2019 07:43:59 Report No.: BSL11505901RF Page 17 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF High Channel: * RBW 3 MHz Marker 1 [T1 ] * VBW 3 MHz -1.59 dBm Ref 11 dBm * Att 30 dB SWT 2.5 ms 2.479820000 GHz 10 Offset 1 dB 1 A 0 1 PK VIEW -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.48 GHz 900 kHz/ Span 9 MHz Date: 29.JAN.2019 07:46:43 Report No.: BSL11505901RF Page 18 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 8. Field Strength of Spurious Emissions 8.1 Standard Applicable According to §15.247(d), in any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a). The emission limit in this paragraph is based on measurement instrumentation employing an average detector. The provisions in §15.35 for limiting peak emissions apply. Spurious Radiated Emissions measurements starting below or at the lowest crystal frequency. 8.2 Test Procedure The setup of EUT is according with per ANSI C63.10-2013 measurement procedure. The specification used was with the FCC Part 15.205 15.247(a) and FCC Part 15.209 Limit. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. Report No.: BSL11505901RF Page 19 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF Antenna Tower 1m-4m 3m EUT SYS 1.5m Turntable Table To EMI Receiver Ground Plane Frequency :9kHz-30MHz Frequency :30MHz-1GHz Frequency :Above 1GHz RBW=10KHz, RBW=120KHz, RBW=1MHz, VBW =30KHz VBW=300KHz VBW=3MHz(Peak), 10Hz(AV) Sweep time= Auto Sweep time= Auto Sweep time= Auto Trace = max hold Trace = max hold Trace = max hold Detector function = peak Detector function = peak, QP Detector function = peak, AV Report No.: BSL11505901RF Page 20 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 8.3 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and the Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Ant. Factor + Cable Loss – Ampl. Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -6dB  V means the emission is 6dB  V below the maximum limit. The equation for margin calculation is as follows: Margin = Corr. Ampl. – FCC Part 15 Limit 8.4 Environmental Conditions Temperature: 25 C Relative Humidity: 52 ATM Pressure: 1012 mbar 8.5 Summary of Test Results/Plots According to the data below, the FCC Part 15.205, 15.209 and 15.247 standards, and had the worst cases: Note: 1. Worst-case radiated emission below 1GHz is GFSK (CH High) mode. 2. Worst-case radiated emission above 1GHz is GFSK (CH Low, Middle, High) mode. Report No.: BSL11505901RF Page 21 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF The Worst Test Data Below 1GHz GFSK (CH High) mode: Plot of Radiated Emissions Test Specification: Horizontal Report No.: BSL11505901RF Page 22 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF Test Specification: Vertical Note: 1.Measurement = Reading + Correct Factor. 2.Correct Factor =Ant. Factor + Cable Loss – Ampl. Gain. Report No.: BSL11505901RF Page 23 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF The Worst Spurious Emissions Above 1GHz Transmitting: BLE mode: Frequency Result Limit Margin Polar Detector (MHz) (dBuV/m) (dBuV/m) (dB) H/V Low Channel-2402MHz 4804 53.25 74 -20.75 H PK 4804 42.34 54 -11.66 H AV 7206 52.27 74 -21.73 H PK 7206 44.63 54 -9.37 H AV 4804 51.71 74 -22.29 V PK 4804 44.73 54 -9.27 V AV 7206 52.35 74 -21.65 V PK 7206 44.42 54 -9.58 V AV Middle Channel-2442MHz 4884 52.59 74 -21.41 H PK 4884 43.63 54 -10.37 H AV 7326 53.24 74 -20.76 H PK 7326 45.33 54 -8.67 H AV 4884 52.27 74 -21.73 V PK 4884 43.68 54 -10.32 V AV 7326 52.43 74 -21.57 V PK 7326 45.88 54 -8.12 V AV High Channel-2480MHz 4960 53.45 74 -20.55 H PK 4960 42.56 54 -11.44 H AV 7440 52.34 74 -21.66 H PK 7440 43.47 54 -10.53 H AV 4960 52.58 74 -21.42 V PK 4960 43.82 54 -10.18 V AV 7440 52.37 74 -21.63 V PK 7440 44.55 54 -9.45 V AV Note: Testing is carried out with frequency rang 9kHz to the tenth harmonics, other than listed in the table above are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. Report No.: BSL11505901RF Page 24 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF Spurious Emission(Conducted) For BLE Low channel: * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -41.81 dBm Ref 11 dBm * Att 30 dB SWT 2.7 s 25.004220000 GHz 10 Offset 1 dB Marker 2 [T1 ] -7.55 dBm 2.403360000 GHz A 0 1 PK 2 VIEW -10 LVL -20 D1 -27.55 dBm -30 1 -40 3DB -50 -60 -70 -80 Start 30 MHz 2.697 GHz/ Stop 27 GHz Middle channel: * RBW 100 kHz Marker 2 [T1 ] Date: 29.JAN.2019 07:54:59 * VBW 300 kHz -42.04 dBm Ref 11 dBm * Att 30 dB SWT 2.7 s 26.838180000 GHz 10 Offset 1 dB Marker 1 [T1 ] -4.37 dBm 2.403360000 GHz A 0 1 1 PK VIEW -10 LVL -20 D1 -24.37 dBm -30 -40 2 3DB -50 -60 -70 -80 Start 30 MHz 2.697 GHz/ Stop 27 GHz Date: 29.JAN.2019 08:01:38 Report No.: BSL11505901RF Page 25 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF High channel: * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -41.70 dBm Ref 11 dBm * Att 30 dB SWT 2.7 s 26.406660000 GHz 10 Offset 1 dB Marker 1 [T1 ] -3.06 dBm 2.457300000 GHz A 0 1 1 PK VIEW -10 LVL -20 D1 -23.06 dBm -30 2 -40 3DB -50 -60 -70 -80 Start 30 MHz 2.697 GHz/ Stop 27 GHz Date: 29.JAN.2019 08:14:01 Report No.: BSL11505901RF Page 26 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 9. Out of Band Emissions 9.1 Standard Applicable According to §15.247 (d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a). 9.2 Test Procedure According to the KDB 558074 D01 v05, the band-edge radiated test method as follows: Set span = wide enough to capture the peak level of the emission operating on the channel closest to the bandedge, as well as any modulation products which fall outside of the authorized band of operation (2310MHz to 2420MHz for low bandedge, 2460MHz to 2500MHz for the high bandedge) RBW = 1MHz, VBW = 1MHz for peak value measured RBW = 1MHz, VBW = 10Hz for average value measured Sweep = auto; Detector function = peak/average; Trace = max hold All the trace to stabilize, set the marker on the emission at the bandedge, or on the highest modulation product outside of the band, if this level is greater than that at the bandedge. Enable the marker-delta function, then use the marker-to-peak function to move the marker to the peak of the in-band emission. Those emission must comply with the 15.209 limit for fall in the restricted bands listed in section 15.205. Note that the method of measurement KDB publication number: 913591 may be used for the radiated bandedge measurements. According to the KDB 558074 D01 v05, the conducted spurious emissions test method as follows: 1. Set start frequency to DTS channel edge frequency. 2. Set stop frequency so as to encompass the spectrum to be examined. 3. Set RBW = 100 kHz. 4. Set VBW ≥ 300 kHz. 5. Detector = peak. 6. Trace Mode = max hold. 7. Sweep = auto couple. 8. Allow the trace to stabilize (this may take some time, depending on the extent of the span). 9. Use peak marker function to determine maximum amplitude of all unwanted emissions within any 100 kHz bandwidth. Ensure that the amplitude of all unwanted emissions outside of the authorized frequency band (excluding restricted frequency bands) are attenuated by at least the minimum requirements specified in section 8.1. Report the three highest emissions relative to the limit. Report No.: BSL11505901RF Page 27 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 9.3 Environmental Conditions Temperature: 23C Relative Humidity: 54 ATM Pressure: 1011 mbar 9.4 Summary of Test Results/Plots Just only show the worst case Bandedge (Radiated) Lowest Bandedge-BLE Channel Freq.(MHz) Reading(dBuV) Factor（dB） Level(dBuV) Limit(dBuV) Margin(dB) Detector 2390 44.68 2.36 47.04 74 -26.96 Peak 2390 37.59 2.36 39.95 54 -14.05 Average LOW 2400 50.56 3.45 54.01 74 -19.99 Peak (2402MHz) 2400 38.35 3.45 41.80 54 -12.20 Average 2483.5 51.33 2.51 53.84 74 -20.16 Peak HIGH 2483.5 39.12 2.51 41.63 54 -12.37 Average (2480MHz) 2500 39.87 3.01 42.88 74 -31.12 Peak 2500 36.26 3.01 39.27 54 -14.73 Average Report No.: BSL11505901RF Page 28 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF Bandedge (Conducted) Lowest * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -4.98 dBm Ref 11 dBm * Att 30 dB SWT 15 ms 2.402200000 GHz 10 Offset 1 dB Marker 2 [T1 ] -56.08 dBm 2.310000000 GHz A 0 1 Marker 3 [T1 ] 1 PK D2 -4.98 dBm -52.91 dBm VIEW -10 2.400000000 GHz LVL Marker 4 [T1 ] -56.44 dBm -20 2.390000000 GHz D1 -24.98 dBm -30 -40 3DB -50 3 2 4 -60 -70 -80 F2 F1 Start 2.3 GHz 14 MHz/ Stop 2.44 GHz High Channel: * RBW 100 kHz Marker 1 [T1 ] Date: 29.JAN.2019 08:20:51 * VBW 300 kHz -2.28 dBm Ref 11 dBm * Att 30 dB SWT 15 ms 2.480040000 GHz 10 Offset 1 dB Marker 2 [T1 ] -55.67 dBm 2.483500000 GHz A 0 1 D1 -2.28 dBm Marker 3 [T1 ] 1 PK -57.06 dBm VIEW -10 2.500000000 GHz LVL Marker 4 [T1 ] -54.07 dBm -20 2.487960000 GHz D2 -22.28 dBm -30 -40 3DB -50 4 2 3 -60 -70 -80 F2 F1 Center 2.495 GHz 11 MHz/ Span 110 MHz Date: 29.JAN.2019 08:28:27 Report No.: BSL11505901RF Page 29 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 10. Conducted Emissions 10.1 Test Procedure The setup of EUT is according with per ANSI C63.4-2014 measurement procedure. The specification used was with the FCC Part 15.207 Limit. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. 10.2 Basic Test Setup Block Diagram EUT Notebook LISN 1.0 m 1.5 To Receiver Non-conduction table 80 cm above Ground Plane 1. 5 m 10.3 Environmental Conditions Temperature: 25 C Relative Humidity: 52 ATM Pressure: 1012 mbar Report No.: BSL11505901RF Page 30 of 31 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL190111991301RF 10.4 Test Receiver Setup During the conducted emission test, the test receiver was set with the following configurations: Start Frequency............................................................................ 150 kHz Stop Frequency............................................................................ 30 MHz Sweep Speed................................................................................ Auto IF Bandwidth............................................................................... 10 kHz Quasi-Peak Adapter Bandwidth.................................................. 9 kHz Quasi-Peak Adapter Mode...........................................................Normal 10.5 Summary of Test Results/Plots According to the data in section 10.6, the EUT complied with the FCC Part 15.207 Conducted margin for this device 10.6 Conducted Emissions Test Data Note: This test is not applicable to battery powered equipment ***** END OF REPORT ***** Report No.: BSL11505901RF Page 31 of 31 FCC Part 15.247


Document Created: 2019-04-30 14:29:18
Document Modified: 2019-04-30 14:29:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC