Test Report_Part 24

FCC ID: 2ARXK201906DB926A

Test Report

Download: PDF
FCCID_4363827

RF TEST REPORT Applicant Veea Inc. FCC ID 2ARXK201906DB926A Product Veeahub Connect 4G Brand Veea (Note the case of letters) Model DB926-A Marketing Veeahub Connect 4G Report No. R1906A0291-R2V1 Issue Date July 18, 2019 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC CFR47 Part 2 (2018)/ FCC CFR 47 Part 24E (2018). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Peng Tao Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86‐021‐50791141/2/3 FAX: +86‐021‐50791141/2/3‐8000

RF Test Report Report No.: R1906A0291-R2V1 TABLE OF CONTENT 1. Test Laboratory ...................................................................................................................................... 4 1.1. Notes of the test report .................................................................................................................. 4 1.2. Test facility..................................................................................................................................... 4 1.3. Testing Location ............................................................................................................................ 5 2. General Description of Equipment under Test....................................................................................... 6 3. Applied Standards .................................................................................................................................. 7 4. Test Configuration .................................................................................................................................. 8 5. Test Case Results .................................................................................................................................. 9 5.1. RF Power Output ........................................................................................................................... 9 5.2. Effective Isotropic Radiated Power ............................................................................................. 12 5.3. Radiates Spurious Emission ....................................................................................................... 16 6. Main Test Instruments ......................................................................................................................... 21 ANNEX A: EUT Appearance and Test Setup.............................................................................................. 22 TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 2 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 Summary of measurement results No. Test Case Clause in FCC rules Verdict Refer to Report No.: 1 RF power output 2.1046 RKS160908001-00A 2 Effective Isotropic Radiated power 24.232(c) PASS Refer to Report No.: 3 Occupied Bandwidth 2.1049 RKS160908001-00A Refer to Report No.: 4 Band Edge Compliance 2.1051 /24.238(a) RKS160908001-00A 24.232/KDB 971168 Refer to Report No.: 5 Peak-to-Average Power Ratio D01(5.7) RKS160908001-00A Refer to Report No.: 6 Frequency Stability 2.1055 / 24.235 RKS160908001-00A Spurious Emissions at Antenna Refer to Report No.: 7 2.1051 / 24.238(a) Terminals RKS160908001-00A 8 Radiates Spurious Emission 2.1053 / 24.238(a) PASS Note: PASS: The EUT complies with the essential requirements in the standard. FAIL: The EUT does not comply with the essential requirements in the standard. Date of Testing: June 17, 2019~ July 5, 2019 According to the power of the sampling test, the test architecture is identical to the module report, so this report refers to the module report (Report No.: RKS160908001-00A) except EIRP and RSE. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 3 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 1. Test Laboratory 1.1. Notes of the test report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2. Test facility FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. IC (recognition number is 8510A) TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. VCCI (recognition number is C-4595, T-2154, R-4113, G-10766) TA Technology (Shanghai) Co., Ltd. has been listed by industry Japan to perform electromagnetic emission measurement. A2LA (Certificate Number: 3857.01) TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 4 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 1.3. Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: xukai@ta-shanghai.com TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 5 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 2. General Description of Equipment under Test Client Information Applicant Veea Inc. Applicant address 164 E 83rd Street, New York, USA Manufacturer Veea Inc. Manufacturer address 164 E 83rd Street, New York, USA General information EUT Description Model DB926-A IMEI / Hardware Version DB926-A V1.00 Software Version EC25AFAR05A05M4G Power Supply External Power Supply Antenna Type External Antenna Antenna Gain 3.4dBi Test Mode(s) WCDMA Band II; LTE Band 2; Test Modulation (WCDMA) BPSK, QPSK,16QAM; (LTE)QPSK,16QAM WCDMA Band II: 26.25 dBm Maximum E.I.R.P LTE Band 2: 25.82 dBm Extreme Temperature Lowest: 0°C Highest: +50°C Band Tx (MHz) Rx (MHz) Operating Frequency Range(s) WCDMA Band II 1850 ~ 1910 1930 ~ 1990 LTE Band 2 1850 ~ 1910 1930 ~ 1990 Note: 1. The information of the EUT is declared by the manufacturer. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 6 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 3. Applied Standards According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC CFR47 Part 2 (2018) FCC CFR 47 Part 24E (2018) ANSI C63.26 (2015) KDB 971168 D01 Power Meas License Digital Systems v03r01 TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 7 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 4. Test Configuration Radiated measurements are performed by rotating the EUT in three different orthogonal test planes. EUT stand-up position (Z axis), lie-down position (X, Y axis). Receiver antenna polarization (horizontal and vertical), the worst emission was found in position (X axis, horizontal polarization) and the worst case was recorded. All mode and data rates and positions and RB size and modulations were investigated. Subsequently, only the worst case emissions are reported. The following testing in WCDMA/LTE is set based on the maximum RF Output Power. Test modes are chosen to be reported as the worst case configuration below: Modes/Modulation Test items WCDMA Band II RMC RF power output HSDPA/HSUPA/HSPA+ Effective Isotropic Radiated power RMC Radiates Spurious Emission RMC Test modes are chosen to be reported as the worst case configuration below for LTE Band 2: Bandwidth (MHz) Modulation RB Test Channel Test items 1.4 3 5 10 15 20 QPSK 16QAM 1 50% 100% L M H RF power output O - - - - O O O O O O - O - Effective Isotropic O O O O O O O O O O O O O O Radiated power Radiates Spurious O - O - - O O - O - - - O - Emission 1. The mark “O” means that this configuration is chosen for testing. Note 2. The mark “-” means that this configuration is not testing. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 8 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 5. Test Case Results 5.1. RF Power Output Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement During the process of the testing, The EUT is controlled by the Base Station Simulator to ensure max power transmission and proper modulation. Test Setup The loss between RF output port of the EUT and the input port of the tester has been taken into consideration. Limits No specific RF power output requirements in part 2.1046. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.4 dB. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 9 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 Test Results Conducted Power(dBm) WCDMA Band II Channel 9262 Channel 9400 Channel 9538 1852.4(MHz) 1880(MHz) 1907.6(MHz) RMC 12.2k 22.92 22.90 22.91 Sub - Test 1 23.04 22.71 22.85 Sub - Test 2 22.95 2.86 22.84 HSDPA Sub - Test 3 22.57 22.68 22.79 Sub - Test 4 22.53 22.76 22.58 Sub - Test 1 22.68 22.86 22.84 Sub - Test 2 22.76 22.64 22.63 HSUPA Sub - Test 3 22.65 22.48 22.68 Sub - Test 4 22.83 22.66 22.45 Sub - Test 5 22.73 22.67 22.52 HSPA+ 16QAM 22.98 22.78 22.94 TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 10 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 LTE Band 2 Conducted Power(dBm) Channel/Frequency (MHz) Bandwidth Modulation RB size RB offset 18607/1850.7 18900/1880 19193/1909.3 1 0 / 23.33 / 1 2 / 23.43 / 1 5 / 23.36 / QPSK 3 0 / 23.10 / 3 2 / 23.15 / 3 3 / 23.22 / 6 0 / 22.14 / 1.4MHz 1 0 / 22.13 / 1 2 / 22.11 / 1 5 / 22.10 / 16QAM 3 0 / 22.05 / 3 2 / 22.06 / 3 3 / 22.09 / 6 0 / 21.17 / Channel/Frequency (MHz) Bandwidth Modulation RB size RB offset 18700/1860 18900/1880 19100/1900 1 0 / 23.46 / 1 50 / 23.22 / 1 99 / 23.24 / QPSK 50 0 / 23.04 / 50 25 / 23.01 / 50 50 / 23.09 / 100 0 / 22.61 / 20MHz 1 0 / 22.13 / 1 50 / 22.51 / 1 99 / 22.35 / 16QAM 50 0 / 22.12 / 50 25 / 22.13 / 50 50 / 22.08 / 100 0 / 21.14 / TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 11 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 5.2. Effective Isotropic Radiated Power Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement The testing follows FCC KDB 971168 v03r01 Section 5.8 and ANSI C63.26 (2015). a) Connect the equipment as illustrated. Mount the equipment with the manufacturer specified antenna in a vertical orientation on a manufacturer specified mounting surface located on a non-conducting rotating platform of a RF anechoic chamber (preferred) or a standard radiation site. b) Key the transmitter, then rotate the EUT 360°azimuthally and record spectrum analyzer power level (LVL) measurements at angular increments that are sufficiently small to permit resolution of all peaks. If a standard radiation test site is used, raise and lower the test antenna to obtain a maximum reading at each angular increment. (Note: several batteries may be needed to offset the effect of battery voltage droop, which should not exceed 5% of the manufactured specified battery voltage during transmission). c) Replace the transmitter under test with a vertically polarized half-wave dipole (or an antenna whose gain is known relative to an ideal half-wave dipole). The center of the antenna should be at the same location as the center of the antenna under test. d) Connect the antenna to a signal generator with a known output power and record the path loss (in dB) as LOSS. If a standard radiation test site is used, raise and lower the test antenna to obtain a maximum reading.LOSS = Generator Output Power (dBm) – Analyzer reading (dBm) e) Determine the effective radiated output power at each angular position from the readings in steps b) and d) using the following equation:ERP (dBm) = LVL (dBm) + LOSS (dB) f) The maximum ERP is the maximum value determined in the preceding step. g) When calculating ERP, in addition to knowing the antenna radiation and matching characteristics, it is necessary to know the loss values of all elements (e.g.transmission line attenuation, mismatches, filters, combiners) interposed between the point where transmitter output power is measured, and the point where power is applied to the antenna. ERP can then be calculated as follows: EIRP (dBm) = Output Power (dBm) - Losses (dB) + Antenna Gain (dBi) where:dBd refers to gain relative to an ideal dipole. EIRP (dBm ) = ERP (dBm) + 2.15 (dB.) The RB allocation refers to section 5.1, using the maximum output power configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 12 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 Test setup Limits Rule Part 24.232(c) Mobile and portable stations are limited to 2 watts EIRP. Rule Part 24.232(e) Peak transmit power must be measured over any interval of continuous transmission using instrumentation calibrated in terms of an rms-equivalent voltage. Limit ≤ 2 W (33 dBm) Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 1.19 dB TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 13 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 Test Results: The measurement is performed for both of horizontal and vertical antenna Polarization, and only the data of worst mode is recorded in this report. Frequency EIRP Limit Mode Channel Polarization Conclusion (MHz) (dBm) (dBm) Low 1852.4 Horizontal 25.54 33 Pass WCDMA Mid 1880 Horizontal 25.48 33 Pass Band II High 1907.6 Horizontal 26.25 33 Pass LTE Band 2 Frequency EIRP Limit bandwidth Channel Polarization Conclusion (MHz) (dBm) (dBm) Low 1850.7 Horizontal 25.35 33 Pass 1.4 MHz Mid 1880 Horizontal 25.17 33 Pass (QPSK) High 1909.3 Horizontal 25.82 33 Pass Low 1851.5 Horizontal 25.23 33 Pass 3 MHz Mid 1880 Horizontal 25.43 33 Pass (QPSK) High 1908.5 Horizontal 25.51 33 Pass Low 1852.5 Horizontal 25.34 33 Pass 5 MHz Mid 1880 Horizontal 25.49 33 Pass (QPSK) High 1907.5 Horizontal 25.41 33 Pass Low 1855 Horizontal 25.46 33 Pass 10 MHz Mid 1880 Horizontal 25.42 33 Pass (QPSK) High 1905 Horizontal 25.62 33 Pass Low 1857.5 Horizontal 25.57 33 Pass 15 MHz Mid 1880 Horizontal 25.51 33 Pass (QPSK) High 1902.5 Horizontal 25.43 33 Pass Low 1860 Horizontal 25.37 33 Pass 20 MHz Mid 1880 Horizontal 25.29 33 Pass (QPSK) High 1900 Horizontal 25.37 33 Pass Low 1850.7 Horizontal 24.76 33 Pass 1.4 MHz Mid 1880 Horizontal 24.67 33 Pass (16QAM) High 1909.3 Horizontal 25.34 33 Pass Low 1851.5 Horizontal 24.68 33 Pass 3 MHz Mid 1880 Horizontal 24.91 33 Pass (16QAM) High 1908.5 Horizontal 25.03 33 Pass Low 1852.5 Horizontal 24.84 33 Pass 5 MHz Mid 1880 Horizontal 24.92 33 Pass (16QAM) High 1907.5 Horizontal 24.87 33 Pass 10 MHz Low 1855 Horizontal 24.98 33 Pass (16QAM) Mid 1880 Horizontal 24.76 33 Pass TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 14 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 LTE Band 2 Frequency EIRP Limit bandwidth Channel Polarization Conclusion (MHz) (dBm) (dBm) High 1905 Horizontal 25.14 33 Pass Low 1857.5 Horizontal 25.02 33 Pass 15 MHz Mid 1880 Horizontal 24.94 33 Pass (16QAM) High 1902.5 Horizontal 24.85 33 Pass Low 1860 Horizontal 24.73 33 Pass 20 MHz Mid 1880 Horizontal 24.62 33 Pass (16QAM) High 1900 Horizontal 24.76 33 Pass TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 15 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 5.3. Radiates Spurious Emission Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement 1. The testing follows FCC KDB 971168 v03r01 Section 5.8 and ANSI C63.26 (2015). 2. Below 1GHz: The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). Above 1GHz: (Note: the FCC’s permission to use 1.5m as an alternative per TCBC Conf call of Dec. 2, 2014.) The EUT is placed on a turntable 1.5 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). 3. A loop antenna, A log-periodic antenna or horn antenna shall be substituted in place of the EUT. The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading of the spectrum analyzer or receiver. 4. The EUT is then put into continuously transmitting mode at its maximum power level during the test. Set Test Receiver or Spectrum RBW=200Hz,VBW=600Hz for 9kHz150kHz , RBW=10kHz, VBW=30kHz 150kHz-30MHz , RBW=100kHz,VBW=300kHz for 30MHz to 1GHz and RBW=1MHz, VBW=3MHz for above 1GHz, And the maximum value of the receiver should be recorded as (Pr). 5. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the frequency band of interest is connected to the substitution antenna with a cable that has been constructed to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the substitution antenna, and adjust the level of the signal generator output until the value of the receiver reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be performed by rotating the test item and adjusting the receiving antenna polarization. 6. A amplifier should be connected to the Signal Source output port. And the cable should be connect between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the Amplifier Gain (PAg) should be recorded after test. 7. The measurement results are obtained as described below: Power(EIRP)=PMea- PAg - Pcl + Ga The measurement results are amend as described below: Power(EIRP)=PMea- Pcl + Ga 8. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 16 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 and known input power. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi. The modulation mode and RB allocation refer to section 5.1, using the maximum output power configuration. Test setup 9KHz ~ 30MHz 30MHz ~ 1GHz Above 1GHz TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 17 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 Note: Area side: 2.4mX3.6m Limits Rule Part 24.238(a) specifies that “on any frequency outside a licensee's frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log10 (P) dB.” Limit -13 dBm Measurement Uncertainty The assessed measurement uncertainty to ensure 95％ confidence level for the normal distribution is with the coverage factor k = 1.96, U= 3.55 dB. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 18 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 Test Result Sweep the whole frequency band through the range from 9kHz to the 10th harmonic of the carrier, the emissions below the noise floor will not be recorded in the report. WCDMA Band II CH-Middle Cable EIRP Frequency SG Gain Antenna Limit Margin Azimuth Harmonic Loss Level (MHz) (dBm) (dBi) Polarization (dBm) (dB) (deg) (dB) (dBm) 2 3760.0 -64.92 5.10 11.05 Horizontal -58.97 -13.00 45.97 180 3 5640.0 -52.68 5.42 12.65 Horizontal -45.45 -13.00 32.45 225 4 7520.0 -57.08 6.70 13.85 Horizontal -49.93 -13.00 36.93 270 5 9400.0 -55.59 7.01 14.75 Horizontal -47.85 -13.00 34.85 0 6 11280.0 -51.42 7.48 15.95 Horizontal -42.95 -13.00 29.95 180 7 13160.0 -54.13 7.51 16.55 Horizontal -45.09 -13.00 32.09 90 8 15040.0 -51.95 8.24 15.35 Horizontal -44.84 -13.00 31.84 135 9 16920.0 -50.48 8.41 14.95 Horizontal -43.94 -13.00 30.94 45 10 18800.0 - - - - - - - - Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2. The worst emission was found in the antenna is Horizontal position. LTE Band 2 1.4MHz CH-Middle Cable EIRP Frequency SG Gain Antenna Limit Margin Azimuth Harmonic Loss Level (MHz) (dBm) (dBi) Polarization (dBm) (dB) (deg) (dB) (dBm) 2 3759.0 -61.10 5.10 11.05 Horizontal -55.15 -13.00 42.15 90 3 5638.9 -49.86 5.42 12.65 Horizontal -42.63 -13.00 29.63 45 4 7520.0 -51.31 6.70 13.85 Horizontal -44.16 -13.00 31.16 135 5 9400.0 -54.59 7.01 14.75 Horizontal -46.85 -13.00 33.85 180 6 11280.0 -51.64 7.48 15.95 Horizontal -43.17 -13.00 30.17 315 7 13160.0 -55.40 7.51 16.55 Horizontal -46.36 -13.00 33.36 45 8 15040.0 -51.43 8.24 15.35 Horizontal -44.32 -13.00 31.32 225 9 16920.0 -50.84 8.41 14.95 Horizontal -44.30 -13.00 31.30 0 10 18800.0 - - - - - - - - Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2. The worst emission was found in the antenna is Horizontal position. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 19 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 LTE Band 2 5MHz CH-Middle Cable EIRP Frequency SG Gain Antenna Limit Margin Azimuth Harmonic Loss Level (MHz) (dBm) (dBi) Polarization (dBm) (dB) (deg) (dB) (dBm) 2 3755.6 -61.94 5.10 11.05 Horizontal -55.99 -43.51 42.99 90 3 5633.6 -50.74 5.42 12.65 Horizontal -43.51 -13.00 30.51 225 4 7520.0 -53.34 6.70 13.85 Horizontal -46.19 -13.00 33.19 180 5 9400.0 -56.76 7.01 14.75 Horizontal -49.02 -13.00 36.02 135 6 11280.0 -53.35 7.48 15.95 Horizontal -44.88 -13.00 31.88 45 7 13160.0 -54.38 7.51 16.55 Horizontal -45.34 -13.00 32.34 0 8 15040.0 -52.83 8.24 15.35 Horizontal -45.72 -13.00 32.72 90 9 16920.0 -50.05 8.41 14.95 Horizontal -43.51 -13.00 30.51 270 10 18800.0 - - - - - - - - Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2. The worst emission was found in the antenna is Horizontal position. LTE Band 2 20MHz CH-Middle Cable EIRP Frequency SG Gain Antenna Limit Margin Azimuth Harmonic Loss Level (MHz) (dBm) (dBi) Polarization (dBm) (dB) (deg) (dB) (dBm) 2 3742.1 -60.68 5.10 11.05 Horizontal -54.73 -13.00 41.73 135 3 5613.4 -49.99 5.42 12.65 Horizontal -42.76 -13.00 29.76 45 4 7484.6 -53.73 6.70 13.85 Horizontal -46.58 -13.00 33.58 180 5 9400.0 -53.77 7.01 14.75 Horizontal -46.03 -13.00 33.03 90 6 11280.0 -51.90 7.48 15.95 Horizontal -43.43 -13.00 30.43 315 7 13160.0 -54.28 7.51 16.55 Horizontal -45.24 -13.00 32.24 45 8 15040.0 -53.08 8.24 15.35 Horizontal -45.97 -13.00 32.97 225 9 16920.0 -50.30 8.41 14.95 Horizontal -43.76 -13.00 30.76 0 10 18800.0 - - - - - - - - Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2. The worst emission was found in the antenna is Horizontal position. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 20 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 6. Main Test Instruments Serial Calibration Expiration Name Manufacturer Type Number Date Date Base Station R&S CMU200 118133 2019-05-19 2020-05-18 Simulator Base Station R&S CMW500 113824 2019-05-19 2020-05-18 Simulator Power Splitter Hua Xiang SHX-GF2-2-13 10120101 / / Spectrum Key sight N9010A MY50210259 2019-05-19 2020-05-18 Analyzer Universal Radio Communication Key sight E5515C MY48367192 2019-05-19 2020-05-18 Tester Signal Analyzer R&S FSV30 100815 2018-12-16 2019-12-15 Loop Antenna SCHWARZBECK FMZB1519 1519-047 2017-09-26 2019-09-25 Trilog Antenna SCHWARZBECK VUBL 9163 9163-201 2017-11-18 2019-11-17 Horn Antenna R&S HF907 100126 2018-07-07 2020-07-06 Horn Antenna ETS-Lindgren 3160-09 00102643 2018-06-20 2020-06-19 Signal R&S SMB 100A 102594 2019-05-19 2020-05-18 generator Climatic ESPEC SU-242 93000506 2017-12-17 2020-12-16 Chamber Preampflier R&S SCU18 102327 2019-05-19 2020-05-18 MOB COMMS Keysight 66319D MY43004105 2019-05-19 2020-05-18 DC SUPPLY RF Cable Agilent SMA 15cm 0001 2019-06-14 2019-09-13 Software R&S EMC32 9.26.0 / / *****END OF REPORT ***** TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 21 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

RF Test Report Report No.: R1906A0291-R2V1 ANNEX A: EUT Appearance and Test Setup The Detailed EUT Appearance and Test Configuration refer to EUT Appearance and Part22_24_27 Test Setup. TA Technology (Shanghai) Co., Ltd. TA-MB-05-002R Page 22 of 22 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.


Document Created: 2019-07-23 13:57:50
Document Modified: 2019-07-23 13:57:50
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC