TCT181220E012_FCC_ID_15.247_BT-1

FCC ID: 2APU8CQL1682-B

Test Report

Download: PDF
FCCID_4314218

TEST REPORT FCC ID: 2APU8CQL1682-B Product: Bluetooth Speaker Model No.: CQL1682-B Additional Model No.: PBT605, SBT716 Trade Mark: SURE, Sharper Image, Polaroid, ART+SOUND, Limitedtoo, DARTA, MAHLI Report No.: TCT181220E012 Issued Date: Dec. 26, 2018 Issued for: Conquer Industry Co., Ltd A-703, Building 2, Tianan Cyber Park, HuangGe North Road, LongGang District, Shenzhen 518172, China Issued By: Shenzhen Tongce Testing Lab. 1B/F., Building 1, Yibaolai Industrial Park, Qiaotou, Fuyong, Baoan District, Shenzhen, Guangdong, China TEL: +86-755-27673339 FAX: +86-755-27673332 Note: This report shall not be reproduced except in full, without the written approval of Shenzhen Tongce Testing Lab. This document may be altered or revised by Shenzhen Tongce Testing Lab. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 TABLE OF CONTENTS 1. Test Certification ..................................................................................... 3 2. Test Result Summary .............................................................................. 4 3. EUT Description ....................................................................................... 5 4. General Information................................................................................. 6 4.1. Test environment and mode ................................................................................. 6 4.2. Description of Support Units ................................................................................ 6 5. Facilities and Accreditations .................................................................. 7 5.1. Facilities ................................................................................................................. 7 5.2. Location ................................................................................................................. 7 5.3. Measurement Uncertainty ..................................................................................... 7 6. Test Results and Measurement Data ..................................................... 8 6.1. Antenna requirement ............................................................................................ 8 6.2. Conducted Emission ............................................................................................. 9 6.3. Conducted Output Power ................................................................................... 13 6.4. 20dB Occupy Bandwidth .................................................................................... 17 6.5. Carrier Frequencies Separation ......................................................................... 21 6.6. Hopping Channel Number .................................................................................. 25 6.7. Dwell Time ............................................................................................................ 28 6.8. Pseudorandom Frequency Hopping Sequence ................................................ 32 6.9. Conducted Band Edge Measurement ................................................................ 33 6.10.Conducted Spurious Emission Measurement.................................................. 36 6.11.Radiated Spurious Emission Measurement ..................................................... 39 Appendix A: Photographs of Test Setup Appendix B: Photographs of EUT Page 2 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 1. Test Certification Product: Bluetooth Speaker Model No.: CQL1682-B Additional PBT605, SBT716 Model No.: SURE, Sharper Image, Polaroid, ART+SOUND, Limitedtoo, Trade Mark: DARTA, MAHLI Applicant: Conquer Industry Co., Ltd A-703, Building 2, Tianan Cyber Park, HuangGe North Road, Address: LongGang District, Shenzhen 518172, China Manufacturer: Conquer Industry Co., Ltd A-703, Building 2, Tianan Cyber Park, HuangGe North Road, Address: LongGang District, Shenzhen 518172, China Date of Test: Dec. 21, 2018 – Dec. 25, 2018 Applicable FCC CFR Title 47 Part 15 Subpart C Section 15.247 Standards: The above equipment has been tested by Shenzhen Tongce Testing Lab. and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Tested By: Date: Dec. 25, 2018 Jerry Xie Reviewed By: Date: Dec. 26, 2018 Beryl Zhao Approved By: Date: Dec. 26, 2018 Tomsin Page 3 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 2. Test Result Summary Requirement CFR 47 Section Result Antenna Requirement §15.203/§15.247 (c) PASS AC Power Line Conducted §15.207 PASS Emission Conducted Peak Output §15.247 (b)(1) PASS Power 20dB Occupied Bandwidth §15.247 (a)(1) PASS Carrier Frequencies §15.247 (a)(1) PASS Separation Hopping Channel Number §15.247 (a)(1) PASS Dwell Time §15.247 (a)(1) PASS Radiated Emission §15.205/§15.209 PASS Band Edge §15.247(d) PASS Note: 1. PASS: Test item meets the requirement. 2. Fail: Test item does not meet the requirement. 3. N/A: Test case does not apply to the test object. 4. The test result judgment is decided by the limit of test standard. Page 4 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 3. EUT Description Product: Bluetooth Speaker Model No.: CQL1682-B Additional Model No.: PBT605, SBT716 SURE, Sharper Image, Polaroid, ART+SOUND, Trade Mark: Limitedtoo, DARTA, MAHLI Bluetooth version: V4.2 Operation Frequency: 2402MHz~2480MHz Transfer Rate: 1/2 Mbits/s Number of Channel: 79 Modulation Type: GFSK, π/4-DQPSK Modulation FHSS Technology: Antenna Type: PCB Antenna Antenna Gain: 0dBi Power Supply: Rechargeable Li-ion Battery DC 3.7V All models above are identical in interior structure, electrical Remark: circuits and components, just model names and trade mark are different for the marketing requirement. Operation Frequency each of channel for GFSK, π/4-DQPSK Channel Frequency Channel Frequency Channel Frequency Channel Frequency 0 2402MHz 20 2422MHz 40 2442MHz 60 2462MHz 1 2403MHz 21 2423MHz 41 2443MHz 61 2463MHz … … … … … … … … 10 2412MHz 30 2432MHz 50 2452MHz 70 2472MHz 11 2413MHz 31 2433MHz 51 2453MHz 71 2473MHz … … … … … … … … 18 2420MHz 38 2440MHz 58 2460MHz 78 2480MHz 19 2421MHz 39 2441MHz 59 2461MHz - Remark: Channel 0, 39 &78 have been tested for GFSK, π/4-DQPSK modulation mode. Page 5 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 4. General Information 4.1. Test environment and mode Operating Environment: Temperature: 25.0 C Humidity: 56 % RH Atmospheric Pressure: 1010 mbar Test Mode: Engineering mode: Keep the EUT in continuous transmitting by select channel and modulations with Fully-charged battery The sample was placed 0.8m & 1.5m for the measurement below & above 1GHz above the ground plane of 3m chamber. Measurements in both horizontal and vertical polarities were performed. During the test, each emission was maximized by: having the EUT continuously working, investigated all operating modes, rotated about all 3 axis (X, Y & Z) and considered typical configuration to obtain worst position, manipulating interconnecting cables, rotating the turntable, varying antenna height from 1m to 4m in both horizontal and vertical polarizations. The emissions worst-case are shown in Test Results of the following pages. 4.2. Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Equipment Model No. Serial No. FCC ID Trade Name Adapter XC-0501000-06-B / / ADAPTER Note: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 3. For conducted measurements (Output Power, 20dB Occupied Bandwidth, Carrier Frequencies Separation, Hopping Channel Number, Dwell Time, Spurious Emissions), the antenna of EUT is connected to the test equipment via temporary antenna connector, the antenna connector is soldered on the antenna port of EUT, and the temporary antenna connector is listed in the Test Instruments. Page 6 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 5. Facilities and Accreditations 5.1. Facilities The test facility is recognized, certified, or accredited by the following organizations: ● FCC - Registration No.: 645098 Shenzhen Tongce Testing Lab The 3m Semi-anechoic chamber has been registered and fully described in a report with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. ● IC - Registration No.: 10668A-1 The 3m Semi-anechoic chamber of Shenzhen TCT Testing Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing 5.2. Location Shenzhen Tongce Testing Lab Address: 1B/F., Building 1, Yibaolai Industrial Park, Qiaotou, Fuyong, Baoan District, Shenzhen, Guangdong, China Tel: 86-755-27673339 5.3. Measurement Uncertainty The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item MU 1 Conducted Emission ±2.56dB 2 RF power, conducted ±0.12dB 3 Spurious emissions, conducted ±0.11dB 4 All emissions, radiated(<1G) ±3.92dB 5 All emissions, radiated(>1G) ±4.28dB 6 Temperature ±0.1°C 7 Humidity ±1.0% Page 7 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6. Test Results and Measurement Data 6.1. Antenna requirement Standard requirement: FCC Part15 C Section 15.203 /247(c) 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 15.247(c) (1)(i) requirement: (i) Systems operating in the 2400-2483.5 MHz band that is used exclusively for fixed. Point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6dBi. E.U.T Antenna: The Bluetooth antenna is PCB antenna which permanently attached, and the best case gain of the antenna is 0dBi. Antenna Page 8 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.2. Conducted Emission 6.2.1. Test Specification Test Requirement: FCC Part15 C Section 15.207 Test Method: ANSI C63.10:2013 Frequency Range: 150 kHz to 30 MHz Receiver setup: RBW=9 kHz, VBW=30 kHz, Sweep time=auto Frequency range Limit (dBuV) (MHz) Quasi-peak Average Limits: 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 Test Setup: Test Mode: Refer to item 4.1 1. The E.U.T is connected to an adapter through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm/50uH coupling impedance for the measuring equipment. 2. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please Test Procedure: refer to the block diagram of the test setup and photographs). 3. Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10:2013 on conducted measurement. Test Result: PASS Page 9 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.2.2. Test Instruments Conducted Emission Shielding Room Test Site (843) Equipment Manufacturer Model Serial Number Calibration Due Test Receiver R&S ESPI 101402 Jul. 17, 2019 LISN Schwarzbeck NSLK 8126 8126453 Sep. 20, 2019 Coax cable TCT CE-05 N/A Sep. 16, 2019 (9KHz-30MHz) Shurple EMI Test Software EZ-EMC N/A N/A Technology Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Page 10 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.2.3. Test data Please refer to following diagram for individual Conducted Emission on Line Terminal of the power line (150 kHz to 30MHz) Note: Freq. = Emission frequency in MHz Reading level (dBµV) = Receiver reading Corr. Factor (dB) = LISN factor + Cable loss Measurement (dBµV) = Reading level (dBµV) + Corr. Factor (dB) Limit (dBµV) = Limit stated in standard Margin (dB) = Measurement (dBµV) – Limits (dBµV) Q.P. =Quasi-Peak AVG =average Any value more than 10dB below limit have not been specifically reported. * is meaning the worst frequency has been tested in the frequency range 150 kHz to 30MHz Page 11 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 Conducted Emission on Neutral Terminal of the power line (150 kHz to 30MHz) Note1: Freq. = Emission frequency in MHz Reading level (dBµV) = Receiver reading Corr. Factor (dB) = LISN factor + Cable loss Measurement (dBµV) = Reading level (dBµV) + Corr. Factor (dB) Limit (dBµV) = Limit stated in standard Margin (dB) = Measurement (dBµV) – Limits (dBµV) Q.P. =Quasi-Peak AVG =average Any value more than 10dB below limit have not been specifically reported. * is meaning the worst frequency has been tested in the frequency range 150 kHz to 30MHz. Note2: Measurements were conducted in all three channels (high, middle, low) and two modulation (GFSK, Pi/4DQPSK), and the worst case Mode (Lowest channel and GFSK) was submitted only. Page 12 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.3. Conducted Output Power 6.3.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (b)(3) Test Method: ANSI C63.10:2013 Section 15.247 (b) The maximum peak conducted output power of the intentional radiator shall not exceed the following: (1) For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 Limit: non-overlapping hopping channels, and all frequency hopping systems in the 5725-5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band 0.125 watts. Test Setup: Test Mode: Transmitting mode with modulation Use the following spectrum analyzer settings: Span = approximately 5 times the 20 dB bandwidth, centered on a hopping channel RBW > the 20 dB bandwidth of the emission being measured VBW  RBW Test Procedure: Sweep = auto Detector function = peak Trace = max hold Allow the trace to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Test Result: PASS 6.3.2. Test Instruments Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent N9020A MY49100619 Sep. 20, 2019 RF Cable TCT RE-06 N/A Sep. 20, 2019 (9KHz-26.5GHz) Antenna Connector TCT RFC-01 N/A Sep. 20, 2019 Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Page 13 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.3.3. Test Data GFSK mode Peak Output Power Test channel Limit (dBm) Result (dBm) Lowest 1.31 21.00 PASS Middle 0.97 21.00 PASS Highest -0.23 21.00 PASS Pi/4DQPSK mode Peak Output Power Test channel Limit (dBm) Result (dBm) Lowest 1.30 21.00 PASS Middle 0.93 21.00 PASS Highest -0.22 21.00 PASS Test plots as follows: Page 14 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 GFSK Modulation Lowest channel Middle channel Highest channel Page 15 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 Pi/4DQPSK Modulation Lowest channel Middle channel Highest channel Page 16 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

I c I Reporti: rorerzamore 6.4. 200B Occupy Bandwidth 6.4.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (a)(1) Test Method: ans! ces. to.2ots Limit: NA Spectrum Anarzer Test Mode: Transmiting mode with modulation 1. The lesing falows ANST 063.10.2013 Neasurement Guidelines. 2. The RF output of EUT was connected to the spectium analyzer by RF cable and aftenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power selting and enable the EUT transmit continuously. Test Procedure: 4. Use the following spectrum analyzer seftings for 20cB Bandwicth measurement. Span = approximately 2 to 5 times the 20 dB bandicth, centered on a hopping channel, 19—RBW <5% of the 20 dB bandwidh; VBWESRBW, Sweep = suto; Detector function = peak; Trace = max hold. 5. Measure and record the resultsin the test report; Test Result PASS €.4.2. Test Instruments Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent Neo20A Mysetoosta Sep. 20, 2019 RF Gabe (@KB2—26.5GH2) Tot REos NA Sep. 20, 2019 Antenna Connector Tot Rrroot NA Sep. 20, 2019 Note: Trecaloraton iteralofhe abovetes rstuments s 12 mrdhs ard e caliruiors ae tacentle o intrnatonal system unt 30 Pase i7 ose Hallines s00—Serters0 Tob Bo—755—27070000 Fus 270002 Mioiiwwndetlib.com

Report No.: TCT181220E012 6.4.3. Test data 20dB Occupy Bandwidth (kHz) Test channel GFSK π/4-DQPSK Conclusion Lowest 1041 1339 PASS Middle 1042 1336 PASS Highest 1046 1349 PASS Test plots as follows: Page 18 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 GFSK Modulation Lowest channel Middle channel Highest channel Page 19 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 Pi/4DQPSK Modulation Lowest channel Middle channel Highest channel Page 20 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.5. Carrier Frequencies Separation 6.5.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (a)(1) Test Method: ANSI C63.10:2013 Frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel Limit: carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB bandwidth of the hopping channel, whichever is greater. Test Setup: Test Mode: Hopping mode 1. The testing follows ANSI C63.10:2013 Measurement Guidelines. 2. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. 4. Enable the EUT hopping function. Test Procedure: 5. Use the following spectrum analyzer settings: Span = wide enough to capture the peaks of two adjacent channels; RBW is set to approximately 30% of the channel spacing, adjust as necessary to best identify the center of each individual channel; VBW≥RBW; Sweep = auto; Detector function = peak; Trace = max hold. 6. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. Record the value in report. Test Result: PASS 6.5.2. Test Instruments Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent N9020A MY49100619 Sep. 20, 2019 RF Cable TCT RE-06 N/A Sep. 20, 2019 (9KHz-26.5GHz) Antenna Connector TCT RFC-01 N/A Sep. 20, 2019 Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Page 21 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.5.3. Test data GFSK mode Carrier Frequencies Test channel Limit (kHz) Result Separation (kHz) Lowest 996 697.33 PASS Middle 1004 697.33 PASS Highest 1002 697.33 PASS Pi/4 DQPSK mode Carrier Frequencies Test channel Limit (kHz) Result Separation (kHz) Lowest 1016 899.33 PASS Middle 990 899.33 PASS Highest 1002 899.33 PASS Note: According to section 6.4 Limit (kHz) 20dB bandwidth (kHz) Mode (Carrier Frequencies (worse case) Separation) GFSK 1046 697.33 π/4-DQPSK 1349 899.33 Test plots as follows: Page 22 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 GFSK Modulation Lowest channel Middle channel Highest channel Page 23 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 Pi/4DQPSK Modulation Lowest channel Middle channel Highest channel Page 24 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.6. Hopping Channel Number 6.6.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (a)(1) Test Method: ANSI C63.10:2013 Frequency hopping systems in the 2400-2483.5 MHz Limit: band shall use at least 15 channels. Test Setup: Test Mode: Hopping mode 1. The testing follows ANSI C63.10:2013 Measurement Guidelines. 2. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. Test Procedure: 4. Enable the EUT hopping function. 5. Use the following spectrum analyzer settings: Span = the frequency band of operation; set the RBW to less than 30% of the channel spacing or the 20 dB bandwidth, whichever is smaller; VBW≥RBW; Sweep = auto; Detector function = peak; Trace = max hold. 6. The number of hopping frequency used is defined as the number of total channel. 7. Record the measurement data in report. Test Result: PASS 6.6.2. Test Instruments Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent N9020A MY49100619 Sep. 20, 2019 RF Cable TCT RE-06 N/A Sep. 20, 2019 (9KHz-26.5GHz) Antenna Connector TCT RFC-01 N/A Sep. 20, 2019 Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Page 25 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 6.6.3. Test data Hopping channel Mode Limit Result numbers GFSK, Pi/4DQPSK 79 15 PASS Test plots as follows: Page 26 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 GFSK Pi/4DQPSK Page 27 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

I c I Report No.: TCT181220E012 6.7. Dwell Time 6.7.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (a)(1) Test Method: ANSI C63.10:2013 The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 Limit: seconds multiplied by the number of hopping channels employed. Test Setup: LZ_E__I &1 _ Test Mode: Hopping mode 1. The testing follows ANSI C63.10:2013 Measurement Guidelines. 2. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. Test Procedure: 4. Enable the EUT hopping function. * 5. Use the following spectrum analyzer settings: Span = zero span, centered on a hopping channel; RBW shall be = channel spacing and where possible RBW should be set >> 1 / T, where T is the expected dwell time per channel; VBW2RBW; Sweep = as necessary to capture the entire dwell time per hopping channel; Detector function = peak; Trace = max hold. 6. Measure and record the results in the test report. Test Result: PASS 6.7.2. Test Instruments Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent N9020A MY49100619 Sep. 20, 2019 RF Cable TCT RE—06 N/A Sep. 20, 2019 (9KHz—26.5GHz) Antenna Connector TCT RFC—01 N/A Sep. 20, 2019 Note: The calibration interval of the above test instruments is 12 months and the calibrations aretraceable to International system unit (S1). Page 28 of 56 Hotline: 400—6611—140 Tel: 86—755—27673339 Fax: 86—755—27673332 hiip://www.ict—lab.com

Report No.: TCT181220E012 6.7.3. Test Data Hops Over Package Dwell Limit Mode Packet Occupancy Transfer time Result (second) Time (hops) Time (ms) (second) GFSK DH1 320 0.423 0.135 0.4 PASS GFSK DH3 160 1.615 0.258 0.4 PASS GFSK DH5 106.67 2.796 0.298 0.4 PASS Pi/4 2-DH1 320 0.409 0.131 0.4 PASS DQPSK Pi/4 2-DH3 160 1.779 0.285 0.4 PASS DQPSK Pi/4 2-DH5 106.67 2.772 0.296 0.4 PASS DQPSK Note: 1. In normal mode, hopping rate is 1600 hops/s with 6 slots in 79 hopping channels. For DH1, With channel hopping rate (1600 / 2 / 79) in Occupancy Time Limit (0.4 x 79) (s), Hops Over Occupancy Time comes to (1600 / 2 / 79) x (0.4 x 79) = 320 hops For DH3, With channel hopping rate (1600 / 4 / 79) in Occupancy Time Limit (0.4 x 79) (s), Hops Over Occupancy Time comes to (1600 / 4 / 79) x (0.4 x 79) = 160 hops For DH5, With channel hopping rate (1600 / 6 / 79) in Occupancy Time Limit (0.4 x 79) (s), Hops Over Occupancy Time comes to (1600 / 6 / 79) x (0.4 x 79) = 106.67 hops 2. Dwell Time(s) = Hops Over Occupancy Time (hops) x Package Transfer Time Test plots as follows: Page 29 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT181220E012 GFSK DH1 DH3 DH5 Page 30 of 56 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com


Document Created: 2019-06-06 05:44:07
Document Modified: 2019-06-06 05:44:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC