Users Manual.pdf

FCC ID: 2APLE18300397

Users Manual

Download: PDF
FCCID_4111669

Connecting the Gateway 4. Connect the cables following steps a through d below. Installation Guide 1. Verify the package contents. ADT Pulse® Interactive Solutions 2. Decide where to place the Gateway. Model: ADT Pulse Gateway PGZNG1 Note: For best Wi-Fi coverage, identify a relatively central location within the premises. Ensure that the Gateway can be conveniently wired to both the broadband Security Panel Package Contents 3. router and security panel, and is close to an AC outlet. Install the Gateway in the proper orientation: • Mount vertically (using the stand or wall mount kit) if the security panel and most devices are on the same floor as the Gateway. • Place horizontally if the security panel, devices and Gateway occupy multiple Gateway Broadband Router floors. a. Use a 4-wire cable to connect the Security Panel to the Security connector on the Gateway. Gateway Security Panel Stand TX+ TX+ TX- TX- Gateway RX+ RX+ RX- RX- Notes: • The security panel connection requires one of the following: Honeywell Wall Mount Kit HSPIM, DSC Communicator Module, GE Automation Module. Horizontal Mount • Wiring: Tx(-) to Rx(-), Tx(+) to Rx(+), Rx(-) to Tx(-), Rx(+) to Tx(+). • Wires must be stripped and seated deeply in terminal connection points. b. Connect an Ethernet cable from one of the open ports of the broadband router to the Broadband Ethernet port of the Gateway. c. Pull wires gently to verify that Gateway connections are secure. Power Adapter Ethernet Cable 5 1/2 inches d. Plug the power cord into the Gateway and then plug the power adapter into an AC Vertical Mount outlet. 5. Wait until the Power and Devices LEDs on the Gateway become solid green (this could Warning: Do not stack equipment, or place equipment in tight spaces, in drawers, or on take a few minutes). carpets. Make sure that your equipment is surrounded by at least 2 inches (5 centimeters) of air space. 3/16 inches 6. To begin the installation process, go to https://portal.adtpulse.com/activation and use Wall Mount installer credentials to log into the ADT Pulse system.

Troubleshooting Technical Specifications FCC Caution • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two Use the LEDs on the front of the Gateway to determine its status and to troubleshoot its Power adapter • North America (input): 120V, 60 Hz, input conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. operation. • All regions (output): 12 V DC @ 1A output 15W maximum • For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. Physical specifications • Dimensions: 8.5 by 5.75 by 1.3 in (216 by 146 by 33 mm) • This device and its antenna(s) must not be co-located or operated in conjunction with any other LED Description • Weight: 0.95 lb (0.42 kg) antenna or transmitter. • Solid green: Gateway is able to communicate with all devices. Environmental • Operating temperature: 32° to 104° F (0° to 40° C) Canadian Department of Communications Radio Interference Regulations • Blinking green: All devices are OK, and Gateway is communicating with a • Operating humidity: 90% maximum relative humidity, This digital apparatus (ADT Pulse® Interactive Solutions) does not exceed the Class B limits for radio- device. noncondensing noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Devices • Solid amber: Gateway is unable to communicate with a device. • Electromagnetic emissions: Department of Communications. • Blinking amber: Gateway is unable to communicate with a device, but Meets requirements of: FCC Part 15 Class B. This Class [B] digital apparatus complies with Canadian ICES-003. communication with at least one other device is occurring. Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada. • Solid red: Gateway is unable to communicate with the security panel. • Blinking red: Gateway is unable to communicate with the security panel, but FCC Requirements for Operation in the United States Industry Canada Industry Canada statement: device traffic is occurring. This device complies with ISED's licence-exempt RSSs. Operation is subject to the following two This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following FCC Information to User conditions: (1) This two conditions: (1) device may may This device not cause harmful not cause interference, harmful and and interference, (2) this device (2) this mustmust device accept any any accept • Off: Gateway is still starting up. This product does not contain any user serviceable components and is to be used with approved interference interferencereceived, received,including includinginterference interferencethat that may may cause causeundesired undesiredoperation. operation. • Solid green: Gateway is linked with Wi-Fi clients. antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. • Blinking green: Data is being transmitted or received over Wi-Fi. LeIMPORTANT présent appareil NOTE: Radiation est conforme aux CNR Exposure Statement: d' ISED applicables aux appareils radio exempts de licence. • Off: Wi-Fi is not enabled or there are no Wi-Fi devices installed. FCC Guidelines for Human Exposure L'exploitation This equipment complies with IC radiation exposure limits:set est autorisée aux deux conditions suivantes (1)forth le dispositif ne doit pas environment. for an uncontrolled produire de This Wi-Fi This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. brouillage equipmentpréjudiciable, et (2) ce should be installed dispositif and operateddoit accepter with minimumtout brouillage distance 20cmreçu, y compris between un brouillage the radiator & your • Solid green: Gateway is connected for remote interactive services. body. This equipment should be installed and operated with minimum distance of 20 cm between the susceptible de provoquer un fonctionnement indésirable. • Pulsing green: Gateway is establishing a connection for remote interactive radiator and your body. services. This transmitter must not be co-located or operating in conjunction with any other antenna or Caution:Exposure Statement: Radiation Connection transmitter. • Blinking green: Data is being transmitted for remote interactive services. This equipment Ce dispositif estcomplies conformewith à la ISED normeradiation CNR-210exposure limits d'Industrie set forth Canada for anaux applicable uncontrolled environment. appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit • Solid amber: Gateway is waiting to reconnect for remote interactive services. FCC Declaration of Conformity This equipment should be installed and operated with greater than 24cm between the radiator & your body. pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un • Pulsing amber: Gateway is trying to reconnect for remote interactive services. brouillage susceptible de provoquer un fonctionnement indésirable. We, Arlo Technologies, Inc., 2200 Faraday Ave. Suite 150, Carlsbad, CA 92008, declare under our • Solid red: Gateway is unable to connect for remote interactive services. sole responsibility that the ADT Pulse® Interactive Solutions complies with Part 15 Subpart B of FCC Déclaration d'exposition aux radiations: • Off: Gateway is still starting up or activation has not been completed. CFR47 Rules. Operation is subject to the following two conditions: Cet équipement NOTE est conforme IMPORTANTE: aux limitesd'exposition Déclaration d'exposition aux aux radiations: rayonnements ISED établies pour un • Solid green: Gateway is powered on. • This device may not cause harmful interference, and environnement Cet équipementnon estcontrôlé. conformeCet auxéquipement doit êtreaux limites d'exposition installé et utilisé àICplus rayonnements de 24pour établies cm un entre le radiateur • This device must accept any interference received, including interference that may cause etenvironnement votre corps. non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de • Blinking green: Gateway is starting up. undesired operation. distance entre la source de rayonnement et votre corps. • Blinking amber: Gateway firmware is being downloaded. Power FCC Radio Frequency Interference Warnings & Instructions • Off: Gateway is powered off. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful License information available at www.ADT.com or by calling 800.ADT.ASAP. CA ACO7155, PPO17232-974443; interference to radio communications. This certification does not guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or FL EF0001121; LA F1639, F1407, F1640; MA 172C; NY 12000305615; PA 090797; MS 15019511. television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. © 2013 ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT logo, 800.ADT.ASAP and the • Connect the equipment into an electrical outlet on a circuit different from that which the radio product names listed in this document are marks and/or registered marks. Unauthorized use is strictly prohibited. November 2018 receiver is connected.


Document Created: 2018-12-17 19:45:44
Document Modified: 2018-12-17 19:45:44
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC