Test Report

FCC ID: 2AOFDNB05-01

Test Report

Download: PDF
FCCID_3731758

JE Py j ME b p im § oo ZranS (AccrepitreDp) ubyts® No. 3857.01 RF TEST REPORT Applicant Zhejiang Lierda Internet of Things technology Co.,Ltd FCC ID 2AOFDNBO5—01 Product NB—lo1T Module(LTE) Brand Lierda Model NBO5—01 Report No. RXA1711—0359RFO1RZ2 Issue Date January 29, 2018 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC CFR47 Part 2 (2017)/ FCC CFR 47 Part 22H (2017). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Jiangpeng Lan Approved by} Kel u TA Technology (Shanghai) Coy— No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86—021—50791141/2/3 FAX: +86—021—50791141/2/3—8000

FCC RF Test Report Report No: RXA1711-0359RF01R2 TABLE OF CONTENT 1. Test Laboratory ...................................................................................................................................... 4 1.1. Notes of the Test Report ............................................................................................................... 4 1.2. Test facility..................................................................................................................................... 4 1.3. Testing Location ............................................................................................................................ 5 2. General Description of Equipment under Test....................................................................................... 6 3. Applied Standards .................................................................................................................................. 7 4. Test Configuration .................................................................................................................................. 8 5. Test Case Results .................................................................................................................................. 9 5.1. RF Power Output ........................................................................................................................... 9 5.2. Effective Radiated Power ............................................................................................................ 11 5.3. Occupied Bandwidth ................................................................................................................... 14 5.4. Band Edge Compliance ............................................................................................................... 18 5.5. Peak-to-Average Power Ratio (PAPR) ....................................................................................... 21 5.6. Frequency Stability ...................................................................................................................... 23 5.7. Spurious Emissions at Antenna Terminals ................................................................................. 26 5.8. Radiates Spurious Emission ....................................................................................................... 29 6. Main Test Instruments ......................................................................................................................... 33 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 2 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Summary of measurement results No. Test Type Clause in FCC rules Verdict 1 RF power output 2.1046 PASS 2 Effective Radiated Power 22.913(a)(2) PASS 3 Occupied Bandwidth 2.1049 PASS 4 Band Edge Compliance 2.1051 / 22.917(a) PASS 22.913(d)/ 5 Peak-to-Average Power Ratio PASS KDB 971168 D01(5.7) 6 Frequency Stability 2.1055 / 22.355 PASS 7 Spurious Emissions at Antenna Terminals 2.1051 / 22.917(a) PASS 8 Radiates Spurious Emission 2.1053 / 22.917 (a) PASS Date of Testing: November 3, 2017~ November 28, 2017 Note: PASS: The EUT complies with the essential requirements in the standard. FAIL: The EUT does not comply with the essential requirements in the standard. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 3 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 1. Test Laboratory 1.1. Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2. Test facility CNAS (accreditation number: L2264) TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS). FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. IC (recognition number is 8510A) TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. VCCI (recognition number is C-4595, T-2154, R-4113, G-10766) TA Technology (Shanghai) Co., Ltd. has been listed by industry Japan to perform electromagnetic emission measurement. A2LA (Certificate Number: 3857.01) TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 4 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 1.3. Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: xukai@ta-shanghai.com TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 5 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 2. General Description of Equipment under Test Client Information Applicant Zhejiang Lierda Internet of Things technology Co.,Ltd Applicant address Lierda IOT park, No.1326 Wenyi Xi Road, Hangzhou, China Manufacturer Zhejiang Lierda Internet of Things technology Co.,Ltd Manufacturer address Lierda IOT park, No.1326 Wenyi Xi Road, Hangzhou, China General Information EUT Description Model NB05-01 IMEI 865352030093602 Hardware Version 01 Software Version 01 Power Supply External power supply The EUT don’t have standard Antenna, The Antenna used for Antenna Type testing in this report is the after-market accessory (Dipole Antenna) Test Mode(s) NB-IOT Band 5 Test Modulation BPSK, QPSK Category NB1 Deployment stand-alone Sub-carrier spacing 3.75KHz, 15KHz Ntones single Maximum E.R.P. NB-IOT Band 5: 25.88 dBm Rated Power Supply Voltage 3.6V Extreme Voltage Minimum: 3.1V Maximum: 4.2V Extreme Temperature Lowest: -30°C Highest: +85°C Band Tx (MHz) Rx (MHz) Operating Frequency Range(s) NB-IOT Band 5 824 ~ 849 869 ~ 894 Note: The information of the EUT is declared by the manufacturer. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 6 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 3. Applied Standards According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC CFR47 Part 2 (2017) FCC CFR 47 Part 22H (2017) ANSI/TIA-603-D (2010) KDB 971168 D01 Power Meas License Digital Systems v03 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 7 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 4. Test Configuration Radiated measurements are performed by rotating the EUT in three different orthogonal test planes. EUT stand-up position (Z axis), lie-down position (X, Y axis). Receiver antenna polarization (horizontal and vertical), the worst emission was found in position (X axis, horizontal polarization) and the worst case was recorded. All mode and data rates and positions were investigated. Subsequently, only the worst case emissions are reported. The following testing in NB-IOT is set based on the maximum RF Output Power. Test modes are chosen to be reported as the worst case configuration below: Test modes are chosen as the worst case configuration below for NB-IOT Band 5. Subcarrier Deployment Spacing Modulation Test Channel Test items Modes mode (kHz) Stand-alone 3.75 15 BPSK QPSK L M H RF power output NB-IOT B5 O O O O O O O O Effective Isotropic NB-IOT B5 O O O O O O O O Radiated power Occupied Bandwidth NB-IOT B5 O O O O O O O O Band Edge Compliance NB-IOT B5 O O O O O O - O Peak-to-Average Power NB-IOT B5 O O O O O - O - Ratio Frequency Stability NB-IOT B5 O O O O O - O - Spurious Emissions at NB-IOT B5 O - O - O O O O Antenna Terminals Radiates Spurious NB-IOT B5 O - O - O O O O Emission Note 1. The mark “O” means that this configuration is chosen for testing. 2. The mark “-” means that this configuration is not testing. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 8 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5. Test Case Results 5.1. RF Power Output Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement During the process of the testing, The EUT is controlled by the Base Station Simulator to ensure max power transmission and proper modulation. Test Setup The loss between RF output port of the EUT and the input port of the tester has been taken into consideration. Limits No specific RF power output requirements in part 2.1046. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.4 dB. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 9 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test Results Sub-carrier Conducted Power (dBm) Mode Modulation spacing Ntones for low/mid/high channel (KHz) 20401/824.1 20525/836.5 20649/848.9 1@0 22.49 22.65 22.68 3.75 1@47 22.47 22.61 22.66 BPSK 1@0 22.43 22.62 22.65 15.00 Band 5 1@11 22.48 22.60 22.67 Standalone 1@0 22.48 22.62 22.66 3.75 1@47 22.52 22.56 22.68 QPSK 1@0 22.45 22.59 22.68 15.00 1@11 22.50 22.64 22.70 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 10 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5.2. Effective Radiated Power Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement The testing follows FCC KDB 971168 v03 Section 5.8 and ANSI/TIA-603-D-2010. a) Connect the equipment as illustrated. Mount the equipment with the manufacturer specified antenna in a vertical orientation on a manufacturer specified mounting surface located on a non-conducting rotating platform of a RF anechoic chamber (preferred) or a standard radiation site. b) Key the transmitter, then rotate the EUT 360°azimuthally and record spectrum analyzer power level (LVL) measurements at angular increments that are sufficiently small to permit resolution of all peaks. If a standard radiation test site is used, raise and lower the test antenna to obtain a maximum reading at each angular increment. (Note: several batteries may be needed to offset the effect of battery voltage droop, which should not exceed 5% of the manufactured specified battery voltage during transmission). c) Replace the transmitter under test with a vertically polarized half-wave dipole (or an antenna whose gain is known relative to an ideal half-wave dipole). The center of the antenna should be at the same location as the center of the antenna under test. d) Connect the antenna to a signal generator with a known output power and record the path loss (in dB) as LOSS. If a standard radiation test site is used, raise and lower the test antenna to obtain a maximum reading.LOSS = Generator Output Power (dBm) – Analyzer reading (dBm) e) Determine the effective radiated output power at each angular position from the readings in steps b) and d) using the following equation:ERP (dBm) = LVL (dBm) + LOSS (dB) f) The maximum ERP is the maximum value determined in the preceding step. g) When calculating ERP, in addition to knowing the antenna radiation and matching characteristics, it is necessary to know the loss values of all elements (e.g.transmission line attenuation, mismatches, filters, combiners) interposed between the point where transmitter output power is measured, and the point where power is applied to the antenna. ERP can then be calculated as follows: ERP (dBm) = Output Power (dBm) - Losses (dB) + Antenna Gain (dBd) where:dBd refers to gain relative to an ideal dipole. EIRP (dBm ) = ERP (dBm) + 2.15 (dB.) TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 11 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test setup Limits Rule Part 22.913(a) specifies that "Mobile/portable stations are limited to 7 watts ERP”. Limit ≤7W (38.45 dBm) Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 1.19 dB TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 12 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test Results: The measurement is performed for both of horizontal and vertical antenna Polarization, and only the data of worst mode is recorded in this report. Sub-carrier Output Ant Frequency Polari Losses ERP Mode Channel Modulation spacing Ntones power gain (MHz) zation (dBm) (dBm) (KHz) (dBm) (dBi) BPSK H 3.75 1@0 -23.48 -47.13 1.06 24.71 QPSK H 3.75 1@0 -23.43 -47.13 1.06 24.77 20401 824.1 BPSK H 15.00 1@0 -23.29 -47.13 1.06 24.91 QPSK H 15.00 1@0 -23.09 -47.13 1.06 25.10 BPSK H 3.75 1@0 -23.74 -47.20 1.24 24.70 Band5 QPSK H 3.75 1@0 -23.74 -47.20 1.24 24.69 20525 836.5 BPSK H 15.00 1@0 -23.26 -47.20 1.24 25.18 QPSK H 15.00 1@0 -23.33 -47.20 1.24 25.11 BPSK H 3.75 1@0 -23.09 -47.59 1.38 25.88 QPSK H 3.75 1@0 -23.73 -47.59 1.38 25.25 20649 848.9 BPSK H 15.00 1@0 -23.35 -47.59 1.38 25.62 QPSK H 15.00 1@0 -23.34 -47.59 1.38 25.63 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 13 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5.3. Occupied Bandwidth Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to Spectrum Analyzer and Base Station Simulator via power Splitter. The occupied bandwidth is measured using spectrum analyzer. RBW is set to 2kHz, VBW is set to 6.2kHz for NB-IOT Band 5 99% power and -26dBc occupied bandwidths are recorded. Spectrum analyzer plots are included on the following pages. Test Setup Limits No specific occupied bandwidth requirements in part 2.1049. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 624Hz. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 14 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test Result Bandwidth(KHz) for low/mid/high channel Sub-carrier 20401/824.1 20525/836.5 20649/848.9 Mode Modulation spacing Ntones 99% 99% 99% (KHz) -26dBc -26dBc -26dBc Power Power Power BPSK 3.75 1@0 66.535 50.92 66.113 50.81 64.169 50.72 Band 5 QPSK 3.75 1@0 79.311 54.46 78.514 54.99 78.060 54.45 Standalone BPSK 15 1@0 90.395 121.00 90.795 121.30 90.990 120.90 QPSK 15 1@0 109.150 138.80 103.510 139.80 98.319 127.40 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 15 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 NB-IOT Band 5 BPSK 3.75kHz 1@0 CH-Low NB-IOT Band 5 BPSK 15kHz 1@0 CH-Low NB-IOT Band 5 BPSK 3.75kHz 1@0 CH-Middle NB-IOT Band 5 BPSK 15kHz 1@0 CH-Middle NB-IOT Band 5 BPSK 3.75kHz 1@0 CH-High NB-IOT Band 5 BPSK 15kHz 1@0 CH-High TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 16 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 NB-IOT Band 5 QPSK 3.75kHz 1@0 CH-Low NB-IOT Band 5 QPSK 15kHz 1@0 CH-Low NB-IOT Band 5 QPSK 3.75kHz 1@0 CH-Middle NB-IOT Band 5 QPSK 15kHz 1@0 CH-Middle NB-IOT Band 5 QPSK 3.75kHz 1@0 CH-High NB-IOT Band 5 QPSK 15kHz 1@0 CH-High TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 17 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5.4. Band Edge Compliance Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to Spectrum Analyzer and Base Station Simulator via power Splitter. The band edge of the lowest and highest channels were measured. The average detector is used. RBW is set to 51Hz, VBW is set to 160Hz for 3.75KHz single carrier, RBW is set to 200Hz, VBW is set to 620Hz for 15KHz single carrier, Spectrum analyzer plots are included on the following pages. Test Setup Limits Rule Part 22.917(a) specifies that “The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB.” Limit -13 dBm Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96, U=0.684dB. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 18 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test Result: NB-IOT Band 5 BPSK 3.75kHz 1@0 CH-Low NB-IOT Band 5 BPSK 3.75kHz 1@47 CH-High NB-IOT Band 5 BPSK 15kHz 1@0 CH-Low NB-IOT Band 5 BPSK 15kHz 1@11 CH-High TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 19 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 NB-IOT Band 5 QPSK 3.75kHz 1@0 CH-Low NB-IOT Band 5 QPSK 3.75kHz 1@47 CH-High NB-IOT Band 5 QPSK 15kHz 1@0 CH-Low NB-IOT Band 5 QPSK 15kHz 1@11 CH-High TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 20 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5.5. Peak-to-Average Power Ratio (PAPR) Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement Measure the total peak power and record as PPk. And measure the total average power and record as PAvg. Both the peak and average power levels must be expressed in the same logarithmic units (e.g., dBm). Determine the PAPR from: PAPR (dB) = PPk (dBm) - PAvg (dBm). Test Setup Limits According to the Sec. 22.913(d), The peak-to-average ratio (PAR) of the transmission must not exceed 13 dB. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.4 dB. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 21 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test Results Sub-carrier Peak-to-Average Power Ratio (PAPR) Channel/ Mode Modulation spacing Frequency(MHz) Peak(dBm) Avg(dBm) PAPR(dB) (KHz) BPSK 3.75 20525/836.5 25.08 22.65 2.43 Band 5 QPSK 3.75 20525/836.5 28.12 22.62 5.50 Standalone BPSK 15 20525/836.5 25.28 22.62 2.66 QPSK 15 20525/836.5 28.22 22.59 5.63 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 22 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5.6. Frequency Stability Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement 1. Frequency Stability (Temperature Variation) The temperature inside the climate chamber is varied from -30°C to +85°C in 10°C step size, (1) With all power removed, the temperature was decreased to 0°C and permitted to stabilize for three hours. (2) Measure the carrier frequency with the test equipment in a “call mode”. These measurements should be made within 1 minute of powering up the mobile station, to prevent significant self warming. (3) Repeat the above measurements at 10°C increments from -30°C to +85°C. Allow at least 1.5 hours at each temperature, un-powered, before making measurements. Frequency Stability (Voltage Variation) The frequency stability shall be measured with variation of primary supply voltage as follows: (1) Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment. (2) For hand carried, battery powered equipment, reduce primary supply voltage to the battery-operating end point which shall be specified by the manufacturer. This transceiver is specified to operate with an input voltage of between 3.1 V and 4.2 V, with a nominal voltage of 3.6V. Test setup TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 23 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Limits According to the Sec. 22.355, the frequency stability of the carrier shall be accurate to within 2.5 ppm of the received frequency for mobile stations. Limits ≤ 2.5 ppm Measurement Uncertainty The assessed measurement uncertainty to ensure 99.75％ confidence level for the normal distribution is with the coverage factor k = 3, U= 0.01ppm. Test Result Sub-carrier Frequency Stability (ppm) Channel/ Mode spacing Test status Frequency(MHz) BPSK QPSK (KHz) 20525/836.5 -30°C/Normal Voltage 0.04562 0.04138 20525/836.5 -20°C/Normal Voltage 0.04569 0.04101 20525/836.5 -10°C/Normal Voltage 0.04531 0.04162 20525/836.5 0°C/Normal Voltage 0.04695 0.04457 20525/836.5 10°C/Normal Voltage 0.04301 0.04533 20525/836.5 20°C/Normal Voltage 0.04493 0.04182 20525/836.5 30°C/Normal Voltage 0.04415 0.04059 3.75 20525/836.5 40°C/Normal Voltage 0.04392 0.04134 20525/836.5 50°C/Normal Voltage 0.04656 0.04367 20525/836.5 60°C/Normal Voltage 0.04488 0.04273 20525/836.5 70°C/Normal Voltage 0.04385 0.04087 20525/836.5 80°C/Normal Voltage 0.04342 0.04186 Band 5 20525/836.5 85°C/Normal Voltage 0.04482 0.04146 Standalone 20525/836.5 20°C/Minimum Voltage 0.04236 0.04034 20525/836.5 20°C/Maximum Voltage 0.04333 0.04115 20525/836.5 -30°C/Normal Voltage 0.02686 0.02945 20525/836.5 -20°C/Normal Voltage 0.02709 0.01990 20525/836.5 -10°C/Normal Voltage 0.03037 0.02995 20525/836.5 0°C/Normal Voltage 0.03255 0.02056 20525/836.5 10°C/Normal Voltage 0.02978 0.02010 15 20525/836.5 20°C/Normal Voltage 0.03002 0.02850 20525/836.5 30°C/Normal Voltage 0.03051 0.02098 20525/836.5 40°C/Normal Voltage 0.03113 0.02711 20525/836.5 50°C/Normal Voltage 0.03359 0.02613 20525/836.5 60°C/Normal Voltage 0.02962 0.02770 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 24 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 20525/836.5 70°C/Normal Voltage 0.03065 0.03048 20525/836.5 80°C/Normal Voltage 0.02938 0.02862 20525/836.5 85°C/Normal Voltage 0.03145 0.02634 20525/836.5 20°C/Minimum Voltage 0.03297 0.02117 20525/836.5 20°C/Maximum Voltage 0.02927 0.03339 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 25 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5.7. Spurious Emissions at Antenna Terminals Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to Spectrum Analyzer and Base Station Simulator via power Splitter. The measurement is carried out using a spectrum analyzer. The spectrum analyzer scans from 9kHz to the 10th harmonic of the carrier. The peak detector is used. RBW are set to 100 kHz and VBW are set to 300 kHz for below 1G, RBW are set to 1MHz and VBW are set to 3MHz for above 1G, Sweep is set to ATUO. Test setup Limits Rule Part 22.917(a) specifies that “The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log (P) dB.” Limit -13 dBm Measurement Uncertainty The assessed measurement uncertainty to ensure 99.75% confidence level for the normal distribution is with the coverage factor k = 1.96. Frequency Uncertainty 100kHz-2GHz 0.684 dB 2GHz-18GHz 1.407 dB TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 26 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test Result Sweep from 9 kHz to 30MHz, and the emissions more than 20 dB below the permissible value are not reported. If disturbances were found more than 20dB below limit line, the mark is not required for the EUT. The signal beyond the limit is carrier. NB-IOT Band 5 CH-Low 30MHz-1.5GHz NB-IOT Band 5 CH-Low 1.5GHz-9GHz 0 0 -5 -5 -10 -10 FCC CSE FCC CSE -15 -15 -20 -20 -25 -25 -30 -30 -35 -35 -40 -40 Level in dBm Level in dBm -45 -45 -50 -50 -55 -60 -55 -65 -60 -70 -65 -75 -70 -80 -75 -85 -80 -90 -95 -85 -100 -90 1.5 2 3 4 5 6 7 8 9 30 200 400 600 800 1000 1200 1400 1500 Frequency in GHz Frequency in MHz NB-IOT Band 5 CH-Middle 30MHz-1.5GHz NB-IOT Band 5 CH-Middle 1.5GHz-9GHz 0 0 -5 -5 -10 -10 FCC CSE FCC CSE -15 -15 -20 -20 -25 -25 -30 -30 -35 -35 -40 -40 Level in dBm Level in dBm -45 -45 -50 -50 -55 -55 -60 -65 -60 -70 -65 -75 -70 -80 -75 -85 -80 -90 -85 -95 -90 -100 30 200 400 600 800 1000 1200 1400 1500 1.5 2 3 4 5 6 7 8 9 Frequency in MHz Frequency in GHz NB-IOT Band 5 CH-High 30MHz-1.5GHz NB-IOT Band 5 CH-High 1.5GHz-9GHz 0 0 -5 -5 -10 -10 FCC CSE FCC CSE -15 -15 -20 -20 -25 -25 -30 -30 -35 -35 -40 -40 Level in dBm Level in dBm -45 -45 -50 -50 -55 -55 -60 -65 -60 -70 -65 -75 -70 -80 -75 -85 -80 -90 -85 -95 -90 -100 30 200 400 600 800 1000 1200 1400 1500 1.5 2 3 4 5 6 7 8 9 Frequency in MHz Frequency in GHz TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 27 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 If disturbances were found more than 20dB below limit line, the mark is not required for the EUT. Peak Limit Margin Mode Frequency (dBm) (dBm) (dB) CSE_3.75KHZ+BPSK_NB-IOT B5_CHLOW_1.5-9GHz 2472.0 -25.58 -13.00 12.58 CSE_3.75KHZ+BPSK_NB-IOTB5_CHMID_1.5-9GHz 2509.3 -27.33 -13.00 14.33 TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 28 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 5.8. Radiates Spurious Emission Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement 1. The testing follows FCC KDB 971168 v03 Section 5.8 and ANSI/TIA-603-D-2010. 2. The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). 3. A log-periodic antenna or double-ridged waveguide horn antenna shall be substituted in place of the EUT. The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading of the spectrum analyzer or receiver. 4. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set Test Receiver or Spectrum RBW=1MHz,VBW=3MHz for above 1GHz and RBW=100kHz,VBW=300kHz for 30MHz to 1GHz,, And the maximum value of the receiver should be recorded as (Pr). 5. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the frequency band of interest is connected to the substitution antenna with a cable that has been constructed to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the substitution antenna, and adjust the level of the signal generator output until the value of the receiver reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be performed by rotating the test item and adjusting the receiving antenna polarization. 6. A amplifier should be connected to the Signal Source output port. And the cable should be connect between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the Amplifier Gain (PAg) should be recorded after test. 7. The measurement results are obtained as described below: Power(EIRP)=PMea- PAg - Pcl + Ga The measurement results are amend as described below: Power(EIRP)=PMea- Pcl + Ga 8. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and known input power. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 29 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test setup 30MHz~~~ 1GHz Above 1GHz Note: Area side:2.4mX3.6m Limits Rule Part 22.917(a) specifies that “The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log (P) dB.” Limit -13 dBm Measurement Uncertainty The assessed measurement uncertainty to ensure 95％ confidence level for the normal distribution is with the coverage factor k = 1.96, U= 3.55 dB. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 30 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 Test Result NB-IOT Band 5 3.75KHZ+BPSK _CH_LOW Cable ERP Frequency SG Gain Antenna Limit Margin Azimuth Harmonic Loss Level (MHz) (dBm) (dBi) Polarization (dBm) (dB) (deg) (dB) (dBm) 2 1992.00 -53.57 2.00 10.75 Horizontal -46.97 -13.00 33.97 90 3 2472.4 -30.68 2.51 11.05 Horizontal -24.29 -13.00 11.29 135 4 3296.4 -55.23 4.20 11.15 Horizontal -50.43 -13.00 37.43 45 5 4120.5 -49.45 5.20 11.15 Horizontal -45.65 -13.00 32.65 270 6 4944.6 -50.61 5.50 11.95 Horizontal -46.31 -13.00 33.31 225 7 5768.7 -50.69 5.70 13.55 Horizontal -44.99 -13.00 31.99 135 8 6592.8 -49.10 6.30 13.75 Horizontal -43.80 -13.00 30.80 45 9 7416.9 -44.34 6.80 13.85 Horizontal -39.44 -13.00 26.44 315 10 8241.0 -45.83 6.90 14.25 Horizontal -40.63 -13.00 27.63 135 Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2.The worst emission was found in the antenna is Horizontal position. NB-IOT Band 5 3.75KHZ+BPSK _ CH_MID Cable ERP Frequency SG Gain Antenna Limit Margin Azimuth Harmonic Loss Level (MHz) (dBm) (dBi) Polarization (dBm) (dB) (deg) (dB) (dBm) 2 1672.7 -54.19 2.00 10.75 Horizontal -47.59 -13.00 34.59 90 3 2509.3 -32.56 2.51 11.05 Horizontal -26.17 -13.00 13.17 135 4 3346.0 -55.31 4.20 11.15 Horizontal -50.51 -13.00 37.51 45 5 4182.5 -49.64 5.20 11.15 Horizontal -45.84 -13.00 32.84 270 6 5019.0 -50.22 5.50 11.95 Horizontal -45.92 -13.00 32.92 225 7 5855.5 -50.48 5.70 13.55 Horizontal -44.78 -13.00 31.78 135 8 6692.0 -48.81 6.30 13.75 Horizontal -43.51 -13.00 30.51 135 9 7528.5 -45.91 6.80 13.85 Horizontal -41.01 -13.00 28.01 315 10 8365.0 -47.51 6.90 14.25 Horizontal -42.31 -13.00 29.31 0 Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2.The worst emission was found in the antenna is Horizontal position. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 31 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 NB-IOT Band 5 3.75KHZ+BPSK _ CH_HIGH Cable ERP Frequency SG Gain Antenna Limit Margin Azimuth Harmonic Loss Level (MHz) (dBm) (dBi) Polarization (dBm) (dB) (deg) (dB) (dBm) 2 1697.4 -51.61 2.00 10.75 Horizontal -45.01 -13.00 32.01 90 3 2546.5 -33.58 2.51 11.05 Horizontal -27.19 -13.00 14.19 135 4 3395.6 -55.69 4.20 11.15 Horizontal -50.89 -13.00 37.89 45 5 4244.5 -52.62 5.20 11.15 Horizontal -48.82 -13.00 35.82 270 6 5093.4 -49.10 5.50 11.95 Horizontal -44.80 -13.00 31.80 225 7 5942.3 -51.16 5.70 13.55 Horizontal -45.46 -13.00 32.46 135 8 6791.2 -49.07 6.30 13.75 Horizontal -43.77 -13.00 30.77 225 9 7640.1 -46.51 6.80 13.85 Horizontal -41.61 -13.00 28.61 315 10 8489.0 -47.06 6.90 14.25 Horizontal -41.86 -13.00 28.86 270 Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2.The worst emission was found in the antenna is Horizontal position. TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 32 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

FCC RF Test Report Report No: RXA1711-0359RF01R2 6. Main Test Instruments Serial Calibration Expiration Name Manufacturer Type Number Date Date Wireless Test StarPoint SP8315 SP8315-1202 2017-05-08 2018-05-07 Set Power Splitter Hua Xiang SHX-GF2-2-13 10120101 2017-05-14 2018-05-13 Spectrum Agilent N9010A MY47191109 2017-05-20 2018-05-19 Analyzer Signal Analyzer R&S FSV30 100815 2016-12-16 2017-12-15 EMI Test R&S ESCI 100948 2017-05-20 2018-05-19 Receiver Signal R&S SMB 100A 102594 2017-05-14 2018-05-13 generator Signal R&S SMR27 100365 2017-05-14 2018-05-13 generator Trilog Antenna SCHWARZBECK VUBL 9163 9163-201 2014-12-06 2017-12-05 Trilog Antenna SCHWARZBECK VUBL 9163 9163-201 2017-11-18 2020-11-17 Horn Antenna R&S HF907 100126 2014-12-06 2019-12-05 Horn Antenna ETS-Lindgren 3160-09 00102644 2015-01-30 2018-01-29 Climatic Re Ce PT-30B 20101891 2015-07-18 2018-07-17 Chamber RF Cable Agilent SMA 15cm 0001 2017-08-04 2018-02-03 Preampflier R&S SCU18 102327 2017-06-18 2018-06-17 Software R&S EMC32 V 8.52.0 NA NA *****END OF REPORT ***** TA Technology (Shanghai) Co., Ltd. TA-MB-05-001R Page 33 of 33 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.


Document Created: 2019-11-01 15:03:09
Document Modified: 2019-11-01 15:03:09
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC