Test Report 2

FCC ID: 2ANOX69097

Test Report

Download: PDF
FCCID_4483646

AGC Report No.: AGC01082190901FEO3 Page 45 of 66 EUT E7/1000 Model Name E7/1000 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal Freque Meter Readi Factor Emission Level Limits Value Type MH dBu dB dBuV/m dBuV/m 4960.000 54.89 0.22 55.11 74 ak 4960.000 46.15 0.22 46.37 54 AVG 7440.000 43.09 2.64 45.73 74 ak 7440.000 35.75 2.64 38.39 54 AVG EUT E7/1000 Model Name E7/1000 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical Freque Meter Readi Factor Emission Level Limits Value Type MH dB dB dBuV/m dBuV/m 4960.000 52.47 0.22 52.69 74 ak 4960.000 43.72 0.22 43.94 54 AVG 7440.000 41.60 2.64 44.24 74 ak 7440.000 32.04 2.64 34.68 54 AVG R RESULT: PASS Note: Other emissions from 1G to 25 GHz are considered as ambient noise. No recording in the test report. Factor = Antenna Factor + Cable loss — Amplifier gain, Over=Measure—Limit. The "Factor" value can be calculated automatically by software of measurement system. All test modes had been tested. The GFSK modulation is the worst case and recorded in the report. Attestation of Global Compliance(Shenzhen)Co.,Ltd. Add: 2/F., Building 2,Sanwei Chaxi Industrial Park, Sanwei Community, Attestationd Hangcheng Street, Bao‘an District, Shenzhen, Guangdong, China Tel: +86—755 2523 4088 E—mail: agc@age—cert.com Service Hotline:400 089 2118

Report No.: AGC01082190901FE03 Page 46 of 66 TEST RESULT FOR RESTRICTED BANDS REQUIREMENTS EUT E7/1000 Model Name E7/1000 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Horizontal PK AV RESULT: PASS

Report No.: AGC01082190901FE03 Page 47 of 66 EUT E7/1000 Model Name E7/1000 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Vertical PK AV RESULT: PASS

Report No.: AGC01082190901FE03 Page 48 of 66 EUT E7/1000 Model Name E7/1000 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal PK AV RESULT: PASS

Report No.: AGC01082190901FE03 Page 49 of 66 EUT E7/1000 Model Name E7/1000 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical PK AV RESULT: PASS Note: The factor had been edited in the “Input Correction” of the Spectrum Analyzer. So the Amplitude of test plots is equal to Reading level plus the Factor in dB. Use the A dB(μV) to represent the Amplitude. Use the F dB(μV/m) to represent the Field Strength. So A=F. All test modes had been pre-tested. The GFSK modulation is the worst case and recorded in the report.

Report No.: AGC01082190901FE03 Page 50 of 66 11. NUMBER OF HOPPING FREQUENCY 11.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: The frequency band of operation. Depending on the number of channels the device supports, it may be necessary to divide the frequency range of operation across multiple spans, to allow the individual channels to be clearly seen. 2. RBW: To identify clearly the individual channels, set the RBW to less than 30% of the channel spacing or the 20 dB bandwidth, whichever is smaller. 3. VBW ≥ RBW. Sweep: Auto. Detector function: Peak. Trace: Max hold. 4. Allow the trace to stabilize. 11.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 8.2 11.3. MEASUREMENT EQUIPMENT USED The same as described in section 6 11.4. LIMITS AND MEASUREMENT RESULT MEASUREMENT TOTAL NO. OF LIMIT (NO. OF CH) RESULT (NO. OF CH) HOPPING CHANNEL >=15 79 PASS TEST PLOT FOR NO. OF TOTAL CHANNELS Note: The GFSK modulation is the worst case and recorded in the report.

Report No.: AGC01082190901FE03 Page 51 of 66 12. TIME OF OCCUPANCY (DWELL TIME) 12.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Zero span, centered on a hopping channel. 2. RBW shall be≤channel spacing and where possible RBW should be set >> 1 / T, where T is the expected dwell time per channel. 3. Sweep: As necessary to capture the entire dwell time per hopping channel; where possible use a video trigger and trigger delay so that the transmitted signal starts a little to the right of the start of the plot. The trigger level might need slight adjustment to prevent triggering when the system hops on an adjacent channel; a second plot might be needed with a longer sweep time to show two successive hops on a channel. 4. Detector function: Peak. Trace: Max hold. 5. Use the marker-delta function to determine the transmit time per hop. 6. Repeat the measurement using a longer sweep time to determine the number of hops over the period specified in the requirements. The sweep time shall be equal to, or less than, the period specified in the requirements. Determine the number of hops over the sweep time and calculate the total number of hops in the period specified in the requirements, using the following equation: (Number of hops in the period specified in the requirements) = (number of hops on spectrum analyzer) × (period specified in the requirements / analyzer sweep time) 7. The average time of occupancy is calculated from the transmit time per hop multiplied by the number of hops in the period specified in the requirements. 12.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 8.2 12.3. MEASUREMENT EQUIPMENT USED The same as described in section 6 12.4. LIMITS AND MEASUREMENT RESULT Time of Pulse Number of hops in the period Sweep Time Limit Channel for DH5 specified in the requirements (ms) (ms) (ms) Low 2.878 30*4 345.36 400 Middle 2.875 27*4 310.50 400 High 2.866 27*4 309.53 400 Note: The 8-DPSK modulation is the worst case and recorded in the report.

Report No.: AGC01082190901FE03 Page 52 of 66 TEST PLOT OF LOW CHANNEL

Report No.: AGC01082190901FE03 Page 53 of 66 TEST PLOT OF MIDDLE CHANNEL

Report No.: AGC01082190901FE03 Page 54 of 66 TEST PLOT OF HIGH CHANNEL

Report No.: AGC01082190901FE03 Page 55 of 66 13. FREQUENCY SEPARATION 13.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Wide enough to capture the peaks of two adjacent channels. 2. RBW: Start with the RBW set to approximately 30% of the channel spacing; adjust as necessary to best identify the center of each individual channel. 3. Video (or average) bandwidth (VBW) ≥ RBW. 4. Sweep: Auto. e) Detector function: Peak. f) Trace: Max hold. g) Allow the trace to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. 13.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 6.2 13.3. MEASUREMENT EQUIPMENT USED The same as described in section 6.3 13.4. LIMITS AND MEASUREMENT RESULT CHANNEL LIMIT RESULT CHANNEL SEPARATION KHz KHz Pass CH01-CH02 1001 >=25 KHz or 2/3 20 dB BW TEST PLOT FOR FREQUENCY SEPARATION Note: The 8-DPSK modulation is the worst case and recorded in the report.

Report No.: AGC01082190901FE03 Page 56 of 66 APPENDIX A: PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ

Report No.: AGC01082190901FE03 Page 57 of 66 APPENDIX B: PHOTOGRAPHS OF EUT TOTAL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC01082190901FE03 Page 58 of 66 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC01082190901FE03 Page 59 of 66 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC01082190901FE03 Page 60 of 66 RIGHT VIEW OF EUT VIEW OF EUT (PORT)

Report No.: AGC01082190901FE03 Page 61 of 66 Left OPEN VIEW OF EUT-1 OPEN VIEW OF EUT-2 Antenna

Report No.: AGC01082190901FE03 Page 62 of 66 VIEW OF BATTERY INTERNAL VIEW OF EUT-1

Report No.: AGC01082190901FE03 Page 63 of 66 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3

Report No.: AGC01082190901FE03 Page 64 of 66 Right OPEN VIEW OF EUT-1 OPEN VIEW OF EUT-2 Antenna

Report No.: AGC01082190901FE03 Page 65 of 66 VIEW OF BATTERY INTERNAL VIEW OF EUT-1

Report No.: AGC01082190901FE03 Page 66 of 66 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3 ----END OF REPORT----


Document Created: 2019-10-18 12:52:37
Document Modified: 2019-10-18 12:52:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC