User manual

FCC ID: 2ANJH-WHSB1

Users Manual

Download: PDF
FCCID_4300413

IN THE BOX Wyze Contact Sensor Wyze Motion Sensor Wyze Sensor Bridge ( WHCS1) ( WHMS1) ( WHSB1) Wyze Contact Sensor x2 Wyze Sense Starter Kit (battery pre-installed) Wyze Motion Sensor x1 QUICK START GUIDE (battery pre-installed) Wyze Sensor Bridge x1 Quick Start Guide x1 Pin x1 1 2 3 4 2 Insert the Sensor Bridge into the 3 Open the Wyze app and tap the CONTACT SENSOR MOTION SENSOR Pin USB port of a Wyze Cam or Wyze 3 dots on the top right corner of Cam Pan and wait for the Status the Home Page. Select “Add a PLACEMENT PLACEMENT Light to turn solid blue. Product” and then select the 2cm(max.) Sensor type you want to setup Wyze Sensor Bridge first. Follow the instructions in the Wyze app to finish setup. SETUP 1 Ensure your Wyze Cam or Wyze Cam Pan is setup, online, and has POWER 4 Repeat Step 3 for each Contact Ensure the two sections of the Contact Place Sensor approximately 6 feet high and the most updated firmware. and Motion Sensor. Sensor are at most 2 cm apart when closed. ensure the Wyze Logo is in the top left corner. 5 6 7 8 9 STATUS LIGHT it doesn’t turn solid blue after several minutes check to ensure Sensors the Bridge from your camera, wait 30 A sensor isn’t working properly Red light seconds, and then reinsert into the your camera is online and has Ensure your camera is online and has Bridge the latest firmware. Remove the Sensor triggered camera. a stable connection. Replace the Bridge, wait for camera sensor’s battery if its status light Solid yellow light A sensor won’t connect to the Bridge connection to be stable, then doesn’t blink when triggered. The Bridge is powered on, but not connected. Remove the reinsert the Bridge. TROUBLESHOOTING Ensure the Bridge is solid or flashing Bridge, make sure the camera is Solid blue light The Sensor Bridge isn’t connecting blue and the camera has a stable connection. If problems persist, try NEED MORE HELP? online, has the latest firmware, The Bridge is working properly. and then reinsert the Bridge. moving the camera closer to the Resources & Support Ensure your camera is online, has a sensor (we recommend sensors are support.wyze.com Flashing blue light stable connection, and the latest Flashing yellow/blue light placed on the same floor as the Community The Bridge is pairing to a sensor. firmware. If problems persist, remove The Bridge is trying to connect. If Bridge). forums.wyze.com 10 11 12 13 14 accordance with the instructions, may equipment and receiver. were met. This product meets the FCC Statement cause harmful interference to radio -- Connect the equipment into an outlet IC Statement applicable Industry Canada technical communications. However, there is no specifications. Changes or modifications not expressly on a circuit different from that to which This device complies with Industry guarantee that interference will not occur approved by the party responsible for the receiver is connected. Canada’s licence-exempt RSSs. Operation Le présent appareil est conforme aux CNR in a particular installation. If this compliance could void the user's authority equipment does cause harmful -- Consult the dealer or an experienced is subject to the following two conditions: d'Industrie Canada applicable aux to operate the equipment. interference to radio or television radio/TV technician for help appareils radio exempts de licence. (1) This device may not cause interference; L'exploitation est autorisée aux deux This equipment has been tested and reception, which can be determined by This device complies with part 15 of the (2) This device must accept any conditions suivantes : (1) l'appareil ne doit found to comply with the limits for a Class turning the equipment off and on, the FCC rules. Operation is subject to the interference, including interference that pas produire de brouillage, B digital device, pursuant to Part 15 of the user is encouraged to try to correct the following two conditions (1)this device may cause undesired operation of the et (2) l'utilisateur de l'appareil doit FCC Rules. These limits are designed to interference by one or more of the may not cause harmful interference, and device. accepter tout brouillage radioélectrique provide reasonable protection against following measures: (2) this device must accept any subi, même si le brouillage est susceptible harmful interference in a residential -- Reorient or relocate the receiving interference received, including The term “IC: “ before the certification/reg- d'en compromettre le fonctionnement installation. This equipment generates antenna. interference that may cause undesired istration number only signifies that the uses and can radiate radio frequency operation. Industry Canada technical specifications energy and, if not installed and used in -- Increase the separation between the 15 16 17 18 19


Document Created: 2019-05-20 14:12:56
Document Modified: 2019-05-20 14:12:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC