User manual

FCC ID: 2ANHITX-P10

Users Manual

Download: PDF
FCCID_3559295


Anerma REMOTE DEFINITIONS TIP: 1. The Back—light automaticaly tums off at 10 seconds and the LCD display =————LiDlight automaticall tums off after 2 minutes. imgoer Shock Button 2. Press "1/2" button for 3 seconds to eb LightBution turn on the remote, Press "1/2" button Beep Buton 6 Viraton Bution for 3 seconds to tum offthe remote. ShockLevelU® . . Mbationtevelup teeo Viraten Worstonseow ShockLevelDot i aes CramnelBute stok ccoupe: sateysous Chamet uns Charging Port RECEIVER COLLAR DEFINITIONS * Power on/off button: Press the button 2 seconds to tum the receiver on. The receiver wl vibrate. To tumn of, press and hold for 3 seconds, The receiver will beep. * Charging Port A full charge will take 3—4 hours. TIP: 1. When the receiveris low power,the LED incicator wil blink fast 2, When the system is working or fuly charged, the LED indicator willbe sold. 3, The receiver wl go to power saving mode after 1 minute if there is no movement or transmit signal.

Siowly Binking Fast Binking Solid Siowly Binking 3 seconds, 1 time 1 second, 2 times 1 second, 1 time System Running Low Power Full Charged/Pairing Mode Charging SETUP PROCEDURES: 1. Charge the remote and recsiver *Please fully charge the remote and receiver before you use the products. Remote: Fuly charged. The RED LED will become sofid Receiver: Fully charged. The Blue LED will become solid. The charging time takes 3—4 hours, Both LED indicators on the remote and receiver willblink slowiy when charging.

SETUP PROCEDURES (CONTINUED): PAIRING AND TEST THE REMOTE AND RECEIVER (VERY IMPORTANT) 1. Tum on the Remote Controller by holding and pressing the (1/2) button for 3 seconds. TIP: You can choose channel 1 or channel 2 to pair the remote and device. The system can pair 2 receivers at the same time., If you cannot pairthe device successfuly,it may have signal interference. Please move to another place to ry to pair The remote and receiver will go to sieep mode if you don‘t use it for 2 minutes. Any movement on the receiver will actvate the collar and any button on the remote will actvate the remote. 2. Press and hold the power button on 3. Press the power button 3 times on the receiver for 3 seconds to tum on the the receiver to enter the paring mode. Receiver You wil hear a beep and the LED incicator wil become solid. You will now have 10 seconds to finish the pairing. 4. Press the yellow, red or green button on the remote to compate the palring.

STATIC SHOCK TEST: + Secure the included test Bulb Kit on the Receiver Collar‘s Contact Points + Press the RED shock button to test the shock function — The test Bulb wil ight up incicating that the Static Shock Stimulation works VIBRATION TEST: «Press the YELLOW vibration button to test the vibration function + The Recsiver Collarwill vibrate inicating that the Vibration Stimulation works BEEPING TEST: — Press the GREEN beeping button to test the beeping function « The Receiver Collarwil beep inicating that the beeping function works TIP: The level of the beeping mode can NOT be adjusted. Level 0 is set by default FIT THE COLLAR RECEIVER The proper ft and placement of the collar is important for effective training. The contact points must have direct contact with your pet‘s skin on the underside of the neck. TO ASSURE A PROPER FIT, PLEASE FOLLOW THESE STEPS: + Make sure that the collaris turned off «Have your pet standing comfortably (3A) ~Place the collarreceiver on your pe‘s neck close tothe ears. Center the contact points undemeath your pet‘s neck to touch the skin (38) + The collr should fit snugly, yet loose enough to allow one finger to it between the strap and your pets neck (3C) an pe C + Sometimes you need to tim the hair around the contact point to make sure that contact is consistent +DO NOT Shave the pet‘s neck as this may increase the risk of skin imitation. — Routinely Check the fit again as your pet becomes more comfortable with the collar.

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Document Created: 2019-10-30 14:41:51
Document Modified: 2019-10-30 14:41:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC