Modular test report part 19

FCC ID: 2AKQD-ORCA-50

Test Report

Download: PDF
FCCID_3592064

FCC RF Test Report Product Name: LTE Module Model Number: ME909u-523 Report No: SYBH(Z-RF)010032014-2002 FCC ID：QISME909U-523 Reliability Laboratory of Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Tel: +86 755 28780808 Fax: +86 755 89652518

RF Test Report of ME909u-523 Notice 1. The laboratory has Passed the accreditation by China National Accreditation Service for Conformity Assessment (CNAS). The accreditation number is L0310. 2. The laboratory has Passed the accreditation by The American Association for Laboratory Accreditation (A2LA). The accreditation number is 2174.01. 3. The laboratory has been listed by the US Federal Communications Commission to perform electromagnetic emission measurements. The site recognition number is 97456. 4. The laboratory has been listed by Industry Canada to perform electromagnetic emission measurements. The recognition numbers of test site are 6369A-2. 5. The test report is invalid if not marked with the signatures of the persons responsible for preparing and approving the test report. 6. The test report is invalid if there is any evidence of erasure and/or falsification. 7. The test report is only valid for the test samples. 8. Content of the test report, in part or in full, cannot be used for publicity and/or promotional purposes without prior written approval from the laboratory. Report No: Huawei Proprietary and Confidential Page 2 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 Applicant: Huawei Technologies Co., Ltd. Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Date of Receipt Sample: 2014-05-20 Start Date of Test: 2014-05-20 End Date of Test: 2014-05-28 Test Result: Pass Approved by Senior 2014-05-28 Liu Chunlin Engineer: Date Name Signature Prepared by: 2014-05-28 Hexiaolin Date Name Signature Report No: Huawei Proprietary and Confidential Page 3 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 Modification Record No. Last Report No. Modification Description 1 First report. Report No: Huawei Proprietary and Confidential Page 4 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 CONTENT 1 General Information ................................................................................................................................................ 6 1.1 Applied Standard........................................................................................................................................ 6 1.2 Test Location ............................................................................................................................................. 6 1.3 Test Environment Condition ....................................................................................................................... 6 2 Test Summary ........................................................................................................................................................ 7 2.1 Band (814-824 MHz paired with 859-869MHz) .......................................................................................... 7 2.2 Band (824-849 MHz paired with 869-894 MHz) ......................................................................................... 8 3 Description of the Equipment under Test (EUT) ..................................................................................................... 9 3.1 General Description ................................................................................................................................... 9 3.2 EUT Identity ............................................................................................................................................... 9 3.3 Technical Specification ............................................................................................................................ 10 4 General Test Conditions / Configurations ............................................................................................................. 11 4.1 Test Modes .............................................................................................................................................. 11 4.2 Test Environment ..................................................................................................................................... 11 4.3 Test Frequency ........................................................................................................................................ 12 4.4 DESCRIPTION OF TESTS ...................................................................................................................... 14 4.5 Test Setups .............................................................................................................................................. 17 4.6 Test Conditions ........................................................................................................................................ 19 5 Main Test Instruments .......................................................................................................................................... 21 6 Measurement Uncertainty..................................................................................................................................... 22 Report No: Huawei Proprietary and Confidential Page 5 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 1 General Information 1.1 Applied Standard Applied Rules: 47 CFR FCC Part 02:2013 47 CFR FCC Part 90: 2013 47 CFR FCC Part 22: 2013 Test Method: FCC KDB 971168 D01 Power Meas License Digital Systems v02r01 1.2 Test Location Test Location 1: Reliability Laboratory of Huawei Technologies Co., Ltd. Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C 1.3 Test Environment Condition Ambient Temperature: 19.5 to 25 °C Ambient Relative Humidity: 40 to 55 % Atmospheric Pressure: Not applicable Report No: Huawei Proprietary and Confidential Page 6 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 2 Test Summary 2.1 Band (814-824 MHz paired with 859-869MHz) FCC Rule Test Item Requirements Test Result Verdict No. Transmitter Conducted §2.1046, < 100 W. Appendix A PASS Power Output §90.635 Modulation PASS §2.1047 Digital modulation Appendix B Characteristics OBW: No limit. PASS Bandwidth §2.1049 Appendix C EBW: No limit. < 50 + 10Log10(P[Watts]]) at PASS Band Edges §2.1051, Band Edge and for all Appendix D Compliance §90.691 out-of-band emissions wtin 37.5kHz of Block Edge Spurious Emission at §2.1051, < 43 + 10Log10(P[Watts]) for PASS Appendix E Antenna Terminals §90.691 all out-of-band emissions Field Strength of §2.1053, < 43 + 10Log10(P[Watts]) for PASS Appendix F Spurious Radiation §90.691 all out-of-band emissions §2.1055, PASS Frequency Stability < ±2.5ppm. Appendix G §90.213 NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”. Report No: Huawei Proprietary and Confidential Page 7 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 2.2 Band (824-849 MHz paired with 869-894 MHz) Test Item FCC Rule No. Requirements Test Result Verdict Effective (Isotropic) §2.1046, Radiated Power FCC: ERP ≤ 7 W. Appendix A PASS §22.913 Output Data Modulation PASS §2.1047 Digital modulation Appendix B Characteristics OBW: No limit. PASS Bandwidth §2.1049 Appendix C EBW: No limit. ≤ -13 dBm/1%*EBW, in 1 MHz PASS Band Edges §2.1051, bands immediately outside and Appendix D Compliance §22.917 adjacent to the frequency block. FCC: ≤ -13 dBm/100 kHz, from PASS th Spurious Emission at §2.1051, 9 kHz to 10 harmonics but Appendix E Antenna Terminals §22.917 outside authorized operating frequency ranges. Field Strength of §2.1053, FCC: ≤ -13 dBm/100 kHz. PASS Appendix F Spurious Radiation §22.917 §2.1055, PASS Frequency Stability ≤ ±2.5ppm. Appendix G §22.355 NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”. Report No: Huawei Proprietary and Confidential Page 8 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 3 Description of the Equipment under Test (EUT) 3.1 General Description ME909u-523 LTE/HSPA+/HSUPA/HSDPA/WCDMA(UMTS) mode Wireless Module is subscriber equipment in the LTE/UMTS system. ME909u-523 implement such functions as RF signal receiving/transmitting, LTE/HSPA+/HSUPA /HSDPA /WCDMA protocol processing, data service etc. 3.2 EUT Identity NOTE: Unless otherwise noted in the report, the functional boards installed in the units shall be selected from the below list, but not means all the functional boards listed below shall be installed in one unit. 3.2.1 Board Board Hardware Version Description ML2ME909UM Main Board Report No: Huawei Proprietary and Confidential Page 9 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 3.3 Technical Specification Characteristics Description Radio System Type LTE Supported Frequency Range Transmission (TX): 814 to 849 MHz LTE band 26(814 to 824 MHz ) Receiving (RX): 859 to 894 MHz Transmission (TX): 814 to 849 MHz LTE band 26(814 to 824 MHz ) Receiving (RX): 859 to 894 MHz TX and RX Antenna Ports TX & RX port: 1 TX-only port: 0 RX-only port: 1 Target TX Output Power LTE system: 23dBm Supported Channel Bandwidth 1.4 MHz, 3 MHz, 5 MHz, 10 LTE band 26(814 to 824 MHz ) MHz 1.4 MHz, 3 MHz, 5 MHz, 10 LTE band 26(824 to 849 MHz ) MHz, 15 MHz, Designation of Emissions LTE band 26(814 to 824 MHz ) 1M09G7D (1.4 MHz QPSK modulation), (Note: the necessary bandwidth of 1M09W7D (1.4 MHz 16QAM modulation) which is the worst value from the 2M70G7D (3 MHz QPSK modulation), measured occupied bandwidths for 2M71W7D (3 MHz 16QAM modulation) each type of channel bandwidth 4M51G7D (5 MHz QPSK modulation), configuration.) 4M51W7D (5 MHz 16QAM modulation) 8M99G7D (10 MHz QPSK modulation), 9M97W7D (10 MHz 16QAM modulation) LTE band 26(824 to 849 MHz ) 1M09G7D (1.4 MHz QPSK modulation), 1M09W7D (1.4 MHz 16QAM modulation) 2M70G7D (3 MHz QPSK modulation), 2M71W7D (3 MHz 16QAM modulation) 4M51G7D (5 MHz QPSK modulation), 4M51W7D (5 MHz 16QAM modulation) 9M01G7D (10 MHz QPSK modulation), 8M99W7D (10 MHz 16QAM modulation) 13M5G7D (15 MHz QPSK modulation), 13M5W7D (15 MHz 16QAM modulation) Report No: Huawei Proprietary and Confidential Page 10 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 4 General Test Conditions / Configurations 4.1 Test Modes NOTE: The test mode(s) are selected according to relevant radio technology specifications. Test Mode Test Modes Description LTE/TM1 LTE system, QPSK modulation LTE/TM2 LTE system, 16QAM modulation 4.2 Test Environment Environment Parameter Selected Values During Tests Relative Humidity Ambient Temperature TN Ambient VL 3.3V Voltage VN 3.8V VH 4.2V NOTE: VL= lower extreme test voltage VN= nominal voltage VH= upper extreme test voltage TN= normal temperature Report No: Huawei Proprietary and Confidential Page 11 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 4.3 Test Frequency RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 26697 Channel 26740 Channel 26783 TX (1.4M) 814.7 MHz 819 MHz 823.3 MHz Channel 26705 Channel 26740 Channel 26775 TX (3M) 815.5 MHz 819 MHz 822.5 MHz Channel 26715 Channel 26740 Channel 26765 TX (5M) 816.5 MHz 819 MHz 821.5 MHz Channel 26740 Channel 26740 Channel 26740 TX (10M) LTE Band 26 819 MHz 819 MHz 819 MHz (814 to 824 MHz ) Channel 8697 Channel 8740 Channel 8783 RX (1.4M) 859.7 MHz 864 MHz 868.3 MHz Channel 8705 Channel 8740 Channel 8765 RX (3M) 860.5 MHz 864 MHz 867.5 MHz Channel 8715 Channel 8740 Channel 8765 RX (5M) 861.5 MHz 864 MHz 866.5 MHz Channel 8740 Channel 8740 Channel 8740 RX (10M) 864 MHz 864 MHz 864 MHz Report No: Huawei Proprietary and Confidential Page 12 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 26797 Channel 26915 Channel 27033 TX (1.4M) 824.7 MHz 836.5 MHz 848.3 MHz Channel 26805 Channel 26740 Channel 27025 TX (3M) 825.5 MHz 836.5 MHz 847.5 MHz Channel 26815 Channel 26740 Channel 27015 TX (5M) 826.5 MHz 836.5 MHz 846.5 MHz Channel 26840 Channel 26740 Channel 26990 TX (10M) 829 MHz 836.5 MHz 844 MHz Channel 26865 Channel 26740 Channel 26965 TX (15M) LTE Band 26 831.5 MHz 836.5 MHz 841.5 MHz (824 to 849 MHz ) Channel 8697 Channel 8915 Channel 9033 RX (1.4M) 859.7 MHz 881.5 MHz 893.3 MHz Channel 8805 Channel 8915 Channel 9025 RX (3M) 860.5 MHz 881.5 MHz 892.5 MHz Channel 8815 Channel 8915 Channel 9015 RX (5M) 871.5 MHz 881.5 MHz 891.5 MHz Channel 8840 Channel 8915 Channel 8990 RX (10M) 874 MHz 881.5 MHz 889 MHz Channel 8865 Channel 8915 Channel 8965 RX (15M) 876.5 MHz 881.5 MHz 886.5 MHz Report No: Huawei Proprietary and Confidential Page 13 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 4.4 DESCRIPTION OF TESTS 4.4.1 Radiated Power and Radiated Spurious Emissions Radiated spurious emissions are investigated indoors in a semi-anechoic chamber to determine the frequencies producing the worst case emissions. Final measurements for radiated power and radiated spurious emissions are performed on the 3 meter OATS per the guidelines of ANSI/TIA-603-C-2004. The equipment under test was transmitting while connected to its integral antenna and is placed on a wooden turntable 80cm above the ground plane and 3 meters from the receive antenna. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. Emissions are also investigated with the receive antenna horizontally and vertically polarized. A portable or small unlicensed wireless device shall be placed on a non-metallic test fixture or other non-metallic support during testing. The supporting fixture shall permit orientation of the EUT in each of three orthogonal (x, y, z) axis positions such that emissions from the EUT are maximized. Measure the EUT maximum RF power and record the result. A half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula: Pd [dBm] = Pg [dBm] – cable loss [dB] + antenna gain [dBd/dBi] Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]). Note: Reference test setup 3 Report No: Huawei Proprietary and Confidential Page 14 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 4.4.2 Occupied Bandwidth The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1 percent of the selected span as is possible without being below 1 percent. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used since a peak or, peak hold, may produce a wider bandwidth than actual. The trace data points are recovered and are directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 percent of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth. Note: Reference test setup 1. 4.4.3 Spurious and Harmonic Emissions at Antenna Terminal The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. On any frequency outside a licensee’s frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB. Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. Note: Reference test setup 1. 4.4.4 Frequency Stability / Temperature Variation Frequency stability testing is performed in accordance with the guidelines of ANSI/TIA-603-C-2004. The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within Report No: Huawei Proprietary and Confidential Page 15 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 ±0.00025% (±2.5 ppm ) of the center frequency. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Note: Reference test setup 2. Report No: Huawei Proprietary and Confidential Page 16 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 4.5 Test Setups 4.5.1 Test Setup 1 EUT Control Control Computer port(s) Antenna Measurement Attenuator Instrument(s) port(s) Power Power Supply port 4.5.2 Test Setup 2 Temperature Chamber EUT Control Control Computer port(s) Antenna Measurement Attenuator Instrument(s) port(s) Power Power Supply port Report No: Huawei Proprietary and Confidential Page 17 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 4.5.3 Test Setup 3 NOTE: Effective radiated power (ERP) refers to the radiation power output of the EUT, assuming all emissions are radiated from half-wave dipole antennas. 4.5.3.1 Step 1: Pre-test Semi- and/or Full- Anechoic Chamber Measurement Antenna Measurement EUT 3m System 4.5.3.2 Step 2: Substitution method to verify the maximum ERP Semi- and/or Full- Anechoic Chamber Measurement Substitution Antenna Antenna Measurement 3m System Signal Generator Report No: Huawei Proprietary and Confidential Page 18 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 4.6 Test Conditions Test Case Test Conditions Transmit Average Power, Test Env. Ambient Climate & Rated Voltage Output Total Test Setup Test Seup 1 Power Data RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Average Power, Test Env. Ambient Climate & Rated Voltage Spectral Density Test Setup Test Seup 1 (if required) RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Peak-to-Average Ratio Test Env. Ambient Climate & Rated Voltage (if required) Test Setup Test Seup 1 RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Modulation Characteristics Test Env. Ambient Climate & Rated Voltage Test Setup Test Seup 1 RF Channels M (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Bandwidth Occupied Test Env. Ambient Climate & Rated Voltage Bandwidth Test Setup Test Seup 1 RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Emission Test Env. Ambient Climate & Rated Voltage Bandwidth Test Setup Test Seup 1 (if required) RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Band Edges Compliance Test Env. Ambient Climate & Rated Voltage Test Setup Test Seup 1 RF Channels L, H (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Spurious Emission at Antenna Test Env. Ambient Climate & Rated Voltage Terminals Test Setup Test Seup 1 RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Report No: Huawei Proprietary and Confidential Page 19 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 Test Case Test Conditions Test Mode LTE/TM1,LTE/TM2 Field Strength of Spurious Test Env. Ambient Climate & Rated Voltage Radiation Test Setup Test Seup 3 Test Mode LTE/TM1,LTE/TM2 NOTE: If applicable, the EUT conf. that has maximum power density (based on the equivalent power level) is selected. RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Frequency Stability Test Env. (1) -30 °C to +50 °C with step 10 °C at Rated Voltage; (2) VL, VN and VH of Rated Voltage at Ambient Climate. Test Setup Test Seup 2 RF Channels L, M, H (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1,LTE/TM2 Report No: Huawei Proprietary and Confidential Page 20 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 5 Main Test Instruments Manufactu Equipment Name Model Serial Number Cal Date Cal- Due rer Power supply KEITHLEY 2303 1288003 2012-11-19 2014-11-18 Wireless Communication Agilent N4010A MY49081592 2013-10-29 2014-10-28 Test set Universal Radio R&S CMU200 113164 2013-07-18 2014-07-17 Communication Tester Universal Radio R&S CMW500 126855 2013-08-08 2015-08-09 Communication Tester Spectrum Analyzer Agilent E4440A MY48250119 2013-08-09 2014-08-08 Signal Analyzer R&S FSQ31 200021 2013-10-29 2014-10-28 Spectrum Analyzer Agilent N9030A MY49431698 2013-10-29 2014-10-28 Temperature Chamber WEISS WKL64 56246002940010 2014-02-25 2015-02-24 Temperature Chamber ESPEC MW3030 06114003 2014-05-09 2015-05-08 Signal generator Agilent E8257D MY51500314 2014-05-09 2015-05-08 Vector Signal Generator R&S SMU200A 104162 2013-10-29 2014-10-28 Test receiver R&S ESU26 100387 2013-06-05 2014-06-04 Spectrum analyzer R&S FSU3 200474 2013-12-24 2014-12-23 Spectrum analyzer R&S FSU43 100144 2013-12-24 2014-12-23 Double-Ridged Waveguide Horn R&S HF907 100304 2013-02-02 2015-02-01 Antenna (1G~18GHz) Trilog Broadband SCHWAR VULB 9163-490 2013-02-02 2015-02-01 Antenna (30M~3GHz) ZBECK 9163 LOOP R&S HFH2-Z2 100262 2013-03-23 2015-03-22 Antennas(9kHz-30MHz) Pyramidal Horn ETS-LIND Antenna(18GHz-26-5GH 3160-09 5140299 2013-03-05 2015-03-04 GREN z) Artificial Mains Network R&S ENV4200 100134 2013-12-24 2014-12-23 Artificial Mains Network R&S ENV216 100382 2013-12-24 2014-12-23 Report No: Huawei Proprietary and Confidential Page 21 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.

RF Test Report of ME909u-523 6 Measurement Uncertainty For a 95% confidence level (k = 2), the measurement expanded uncertainties for defined systems, in accordance with the recommendations of ISO 17025 as following: Test Item Extended Uncertainty Transmit Output Power Data Power [dBm] U = 0.39 dB Bandwidth Magnitude [%] U = 0.2% Band Edge Compliance Disturbance Power [dBm] U = 2.0 dB Spurious Emissions, Conducted Disturbance Power [dBm] U = 2.0 dB Field Strength of Spurious Radiation ERP [dBm] For 3 m Chamber: U = 4.6 dB (30 MHz to 1GHz) U = 3.0 dB (above 1 GHz) For 10 m Chamber: U = 4.6 dB (30 MHz to 1GHz) U = 3.0 dB (above 1 GHz) Frequency Stability Frequency Accuracy [ppm] U = 0.21 ppm END Report No: Huawei Proprietary and Confidential Page 22 of 22 SYBH(Z-RF)010032014-2002 Copyright © Huawei Technologies Co., Ltd.


Document Created: 2019-09-15 23:03:05
Document Modified: 2019-09-15 23:03:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC