14_XHT-6B16 TestRpt NII p4

FCC ID: 2AKC6XHT-WF6D

Test Report

Download: PDF
FCCID_4345651

AGC Report No.: AGC00742190601FEO6 Page 106 of 125 15. FCC LINE CONDUCTED EMISSION TEST 15.1. LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz~500kHz 66—56 56—46 500kHz~5MHz 56 46 5SMHz~30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50MHz. 15.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST EUT & Support 40cm A socm =BOcm LISN aoEm Attestation of Global Compliance(Shenzhen)Co.,Ltd. Add: 2/F., Building 2, No.1—4, Chaxi Sanwei Technial Industrial Park, Gushu, Xixiang, Bao‘an District, Shenzhen, Guangdong, China Tel: +86—755 2523 4088 E—mail: agc@ageo—cert.com Service Hotline:400 089 2118

Report No.: AGC00742190601FE06 Page 107 of 125 15.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. All support equipments received AC120V/60Hz power from a LISN, if any. 5. The EUT received charging voltage by adapter which received 120V/60Hzpower by a LISN. 6. The test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. 9. The test mode(s) were scanned during the preliminary test. Then, the EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing. 15.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. EUT and support equipment was set up on the test bench as per step 2 of the preliminary test. 2. A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. 3. The test data of the worst case condition(s) was reported on the Summary Data page.

Report No.: AGC00742190601FE06 Page 108 of 125 15.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST LINE CONDUCTED EMISSION TEST-L

Report No.: AGC00742190601FE06 Page 109 of 125 LINE CONDUCTED EMISSION TEST-N RESULT: PASS

Report No.: AGC00742190601FE06 Page 110 of 125 APPENDIX A: PHOTOGRAPHS OF TEST SETUP FCC LINE CONDUCTED EMISSION TEST SETUP FCC RADIATED EMISSION TEST SETUP BELOW 1GHZ

Report No.: AGC00742190601FE06 Page 111 of 125 FCC RADIATED EMISSION TEST SETUP ABOVE 1GHZ

Report No.: AGC00742190601FE06 Page 112 of 125 APPENDIX B: PHOTOGRAPHS OF EUT TEST MODE -XHT-6B16 ALL VIEW OF EUT

Report No.: AGC00742190601FE06 Page 113 of 125 TOP VIEW OF EUT BOTTOM VIEW OF EUT

Report No.: AGC00742190601FE06 Page 114 of 125 FRONT VIEW OF EUT BACK VIEW OF EUT

Report No.: AGC00742190601FE06 Page 115 of 125 LEFT VIEW OF EUT RIGHT VIEW OF EUT

Report No.: AGC00742190601FE06 Page 116 of 125 OPEN VIEW OF EUT 1 OPEN VIEW OF EUT 2

Report No.: AGC00742190601FE06 Page 117 of 125 INTERNAL VIEW OF EUT-1 Antenna connector 0 Antenna connector 1 INTERNAL VIEW OF EUT-2

Report No.: AGC00742190601FE06 Page 118 of 125 VIEW OF PORT -1 VIEW OF PORT -2

Report No.: AGC00742190601FE06 Page 119 of 125 Series Model- XHT-6B18 ALL VIEW OF EUT

Report No.: AGC00742190601FE06 Page 120 of 125 TOP VIEW OF EUT BOTTOM VIEW OF EUT

Report No.: AGC00742190601FE06 Page 121 of 125 FRONT VIEW OF EUT BACK VIEW OF EUT

Report No.: AGC00742190601FE06 Page 122 of 125 LEFT VIEW OF EUT RIGHT VIEW OF EUT

Report No.: AGC00742190601FE06 Page 123 of 125 OPEN VIEW OF EUT 1 INTERNAL VIEW OF EUT-1

Report No.: AGC00742190601FE06 Page 124 of 125 INTERNAL VIEW OF EUT-2 VIEW OF PORT-1

Report No.: AGC00742190601FE06 Page 125 of 125 VIEW OF PORT-2 ----END OF REPORT---


Document Created: 2019-07-06 02:15:17
Document Modified: 2019-07-06 02:15:17
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC