Test Report_DCD

FCC ID: 2AJ9T-PRORFI

Test Report

Download: PDF
FCCID_4084467

Access to the World ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPARTC REQUIREMENT OF Smart Access Control Terminal MODEL No.: ProRF, SCR100 Plus FCC ID: 2AJ9T-PRORFI Trademark: N/A REPORT NO: ES181024030W ISSUE DATE: November 16, 2018 Prepared for ZKTECO CO., LTD. No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China Prepared by EMTEK(SHENZHEN) CO., LTD. Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 TRF No：FCC 15C/A Page 1 of 24 Report No: ES181024030W Ver.1.0

VERIFICATION OF COMPLIANCE Applicant: ZKTECO CO., LTD. No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China Manufacturer: ZKTECO CO., LTD. No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China Product Name: Smart Access Control Terminal Model Number: ProRF, SCR100 Plus Trademark: N/A Measurement Procedure Used: APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 2, Subpart J PASS FCC 47 CFR Part 15, Subpart C The above equipment was tested by EMTEK(SHENZHEN) CO., LTD.. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.207&15.209. The test results of this report relate only to the tested sample identified in this report. October 24, 2018 to November 16, 2018 Date of Test : Prepared by : Sevin Li/Editor Reviewer : Joe Xia/Supervisor Approved & Authorized Signer : Lisa Wang/Manager

Access to the World Table of Contents 1. GENERAL INFORMATION .................................................................................................................... 4 1.1 PRODUCT DESCRIPTION ............................................................................................................................. 4 1.2 RELATED SUBMITTAL(S) / GRANT (S) .......................................................................................................... 4 1.3 TEST METHODOLOGY................................................................................................................................. 4 1.4 SPECIAL ACCESSORIES .............................................................................................................................. 4 1.5 EQUIPMENT MODIFICATIONS....................................................................................................................... 4 1.6 TEST FACILITY ........................................................................................................................................... 5 2. SYSTEM TEST CONFIGURATION ........................................................................................................ 6 2.1 EUT CONFIGURATION ................................................................................................................................ 6 2.2 EUT EXERCISE.......................................................................................................................................... 6 2.3 TEST PROCEDURE ..................................................................................................................................... 6 2.4 LIMITATION ................................................................................................................................................ 6 3. SUMMARY OF TEST RESULTS ............................................................................................................ 8 4. CONDUCTED EMISSION TEST ............................................................................................................. 9 4.1 APPLICABLE STANDARD .................................................................................................................................. 9 4.2 CONFORMANCE LIMIT ...................................................................................................................................... 9 4.3 TEST CONFIGURATION .................................................................................................................................... 9 4.4 TEST PROCEDURE .......................................................................................................................................... 9 4.5 MEASUREMENT EQUIPMENT USED: .................................................................................................................. 9 4.6 TEST RESULT ................................................................................................................................................. 9 5. RADIATED EMISSION TEST ............................................................................................................... 12 5.1 MEASUREMENT PROCEDURE .................................................................................................................... 12 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .............................................................................. 13 5.3 MEASUREMENT EQUIPMENT USED: ........................................................................................................... 13 5.4 MEASUREMENT RESULT .............................................................................................................................. 13 6. ANTENNA APPLICATION ................................................................................................................... 24 ANTENNA REQUIREMENT..................................................................................................................................... 24 RESULT .............................................................................................................................................................. 24 TRF No：FCC 15C/A Page 3 of 24 Report No: ES181024030W Ver.1.0

Access to the World 1. GENERAL INFORMATION 1.1 Product Description Characteristics Description EUT Description Smart Access Control Terminal ProRF, SCR100 Plus Two models are identical in circuitry and electrical, mechanical Model Number and physical construction; the difference is model number for trading purpose; we test ProRF Model Device style RFID Modulation ASK Operating Frequency 125kHz Range Number of Channels 1 Antenna Type Coil Antenna DC supply: DC 12V Power supply Adapter supply: 1.2 Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: 2AJ9T-PRORFI filing to comply with Section 15.207&15.209 of the FCC Part 15 Subpart C Rules. 1.3 Test Methodology Both conducted and radiated testing was performed according to the procedures in ANSI C63.10 (2013) and Radiated testing was performed at an antenna to EUT distance 3 meters. 1.4 Special Accessories Item Equipment Mfr/Brand Model/Type No. Note Input: AC 100-240V, 50/60Hz 1.5A 1 SWITCHING ADAPTOR FUJIA FJ-SW120300N Output: 12V, 3A 1.5 Equipment Modifications Not available for this EUT intended for grant. TRF No：FCC 15C/A Page 4 of 24 Report No: ES181024030W Ver.1.0

Access to the World 1.6 Test Facility Site Description EMC Lab. : Accredited by CNAS, 2016.10.24 The certificate is valid until 2022.10.28 The Laboratory has been assessed and proved to be in compliance with CNAS-CL01: 2006(identical to ISO/IEC17025: 2005) The Certificate Registration Number is L2291 : Accredited by TUV Rheinland Shenzhen, 2010.5.25 The Laboratory has been assessed according to the requirements ISO/IEC 17025. : Accredited by FCC, August 06, 2018 The certificate is valid until August 07, 2020 Designation Number: CN1204 Test Firm Registration Number: 882943 : Accredited by Industry Canada, November 24, 2015 The Certificate Registration Number is 4480A-2 TRF No：FCC 15C/A Page 5 of 24 Report No: ES181024030W Ver.1.0

Access to the World 2. System Test Configuration 2.1 EUT Configuration The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. 2.2 EUT Exercise The Transmitter was operated in the normal operating mode. The TX frequency was fixed which was for the purpose of the measurements. 2.3 Test Procedure 2.3.1 Radiated Emissions The EUT is a placed on as turn table which is 0.8 m above ground plane. The turn table shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the max. emission, the relative positions of this hand-held transmitter(EUT) was rotated through three orthogonal axes according to the requirements in Section 13.1.4.1 of ANSI C63.10 (2013). 2.4 Limitation (1) Radiated Emission FCC Part 15, Subpart C Section 15.209 limit of radiated emission for frequency below 1000GHz. The emissions from an intentional radiator shall not exceed the field strength level specified in the following table: FCC Part 15.209 Field Strength Field Strength Limitation Frequency tion at 3m Frequency Limitation Measurement Dist (MHz) (uV/m) Dist (uV/m) (dBuV/m) 0.009 – 0.490 2400 / F(KHz) 300m 10000 * 2400/F(KHz) 20log 2400/F(KHz) + 80 0.490 – 1.705 24000 / F(KHz) 30m 100 * 24000/F(KHz) 20log 24000/F(KHz) + 40 1.705 – 30.00 30 30m 100* 30 20log 30 + 40 30.0 – 88.0 100 3m 100 20log 100 88.0 – 216.0 150 3m 150 20log 150 216.0 – 960.0 200 3m 200 20log 200 Above 960.0 500 3m 500 20log 500 TRF No：FCC 15C/A Page 6 of 24 Report No: ES181024030W Ver.1.0


Access to the World 3. Summary of Test Results FCC Rule Description Of Test Result 15.207 AC Power Conducted Emission Pass 15.209 Radiated Emission Pass 2.1049 20dB Bandwidth Pass TRF No：FCC 15C/A Page 8 of 24 Report No: ES181024030W Ver.1.0

Access to the World 4. CONDUCTED EMISSION TEST 4.1 Applicable Standard According to FCC Part 15.207(a) 4.2 Conformance Limit Conducted Emission Limit Frequency(MHz) Quasi-peak Average 0.15-0.5 66-56 56-46 0.5-5.0 56 46 5.0-30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.3 Test Configuration Test according to clause 7.3 conducted emission test setup 4.4 Test Procedure The EUT was placed on a table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Repeat above procedures until all frequency measured were complete. 4.5 Measurement Equipment Used: EQUIPMENT MODEL SERIAL MFR LASTCAL. DUE CAL. TYPE NUMBER NUMBER Test Receiver Rohde & Schwarz ESCI 26115-010-0027 May 19, 2018 May 18, 2019 L.I.S.N. Rohde & Schwarz ENV216 101161 May 19, 2018 May 18, 2019 50Ω Coaxial Switch Anritsu MP59B 6100175589 May 20, 2018 May 19, 2019 Voltage Probe Rohde & Schwarz ESH2-Z3 100122 May 20, 2018 May 19, 2019 Pulse Limiter Rohde & Schwarz ESH3-Z2 100006 May 19, 2018 May 18, 2019 I.S.N Teseq GmbH ISN T800 30327 May 20, 2018 May 19, 2019 4.6 Test Result Pass AC 120V &240V voltage have been tested, and the worst result recorded was report as below: TRF No：FCC 15C/A Page 9 of 24 Report No: ES181024030W Ver.1.0



Access to the World 5. Radiated Emission Test 5.1 Measurement Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 4. Repeat above procedures until all frequency measured was complete. When spectrum scanned from 9KHz to 150KHz setting resolution bandwidth 200Hz and video bandwidth 1kHz. EMI Test Receiver Setting Attenuation Auto RB 200Hz VB 1kHz Detector QP Trace Max hold When spectrum scanned from 150KHz to 30MHz setting resolution bandwidth 9 kHz and video bandwidth 30kHz. EMI Test Receiver Setting Attenuation Auto RB 9kHz VB 30kHz Detector QP Trace Max hold When spectrum scanned from 30 MHz to 1GHz setting resolution bandwidth 120 kHz and video bandwidth 300kHz. EMI Test Receiver Setting Attenuation Auto RB 120kHz VB 300kHz Detector QP Trace Max hold TRF No：FCC 15C/A Page 12 of 24 Report No: ES181024030W Ver.1.0

Access to the World 5.2 Test SET-UP (Block Diagram of Configuration) (A) Radiated Emission Test Set-Up, Frequency Below 30MHz Turntable 3m EUT Test 0.8 m Receiver Ground Plane Coaxial Cable (B) Radiated Emission Test Set-Up, Frequency Below 1000MHz 3m Turntable 1m to 4m EUT Spectrum Analyzer 0.8m Ground Plane Coaxial Cable 5.3 Measurement Equipment Used: EQUIPMENT MFR MODEL SERIAL LAST CAL. DUE CAL. TYPE NUMBER NUMBER EMI Test Receiver Rohde & Schwarz ESU 1302.6005.26 May 20, 2018 May 19, 2019 Pre-Amplifier HP 8447F 2944A07999 May 19, 2018 May 18, 2019 Bilog Antenna Schwarzbeck VULB9163 142 May 19, 2018 May 18, 2019 Loop Antenna ARA PLA-1030/B 1029 May 19, 2018 May 18, 2019 Horn Antenna Schwarzbeck BBHA 9170 BBHA9170399 May 20, 2018 May 19, 2019 Horn Antenna Schwarzbeck BBHA 9120 D143 May 19, 2018 May 18, 2019 Cable Schwarzbeck AK9513 ACRX1 May 20, 2018 May 19, 2019 Cable Rosenberger N/A FP2RX2 May 20, 2018 May 19, 2019 Cable Schwarzbeck AK9513 CRPX1 May 20, 2018 May 19, 2019 Cable Schwarzbeck AK9513 CRRX2 May 20, 2018 May 19, 2019 5.4 Measurement Result Pass, see the following page TRF No：FCC 15C/A Page 13 of 24 Report No: ES181024030W Ver.1.0









Access to the World 6. 20DB BANDWIDTH 6.1 Applicable Standard According to FCC Part 2.1049 6.2 Conformance Limit No limit requirement. 6.3 Test Configuration Test according to clause 6.1 radio frequency test setup 1 6.4 Test Procedure The EUT was operating in transmit mode and controlled its channel. Printed out the test result from the spectrum by hard copy function. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. Set to the maximum power setting and enable the EUT transmit continuously Set RBW = 1% occupied bandwidth (3 kHz). Set the video bandwidth (VBW) =3 times RBW (10 kHz). Set Span= approximately 2 to 4 times the occupied bandwidth Set Detector = Peak. Set Trace mode = max hold. Set Sweep = auto couple. The EUT should be transmitting at its maximum data rate. Allow the trace to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 20dB down one side of the emission. Reset the markerdelta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 20dB bandwidth of the emission. If this value varies with different modes of operation (e.g., data rate, modulation format, etc.), repeat this test for each variation. Measure and record the results in the test report. 6.5 Test Results Temperature : 28℃ Test By: Andy Humidity : 65 % Modulation Channel Channel Frequency 20dB Bandwidth Limit Verdict Mode Number (kHz) (kHz) (kHz) ASK 0 125 9.84 N/A PASS Note: N/A (Not Applicable) TRF No：FCC 15C/A Page 22 of 24 Report No: ES181024030W Ver.1.0


Access to the World 7. Antenna Application Antenna Requirement Standard Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier FCC CRF Part 15.203 current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this part are not exceeded. For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. Result PASS. Note: Antenna use a permanently attached antenna which is not replaceable. Not using a standard antenna jack or electrical connector for antenna replacement The antenna has to be professionally installed (please provide method of installation) Which in accordance to section 15.203, please refer to the internal photos TRF No：FCC 15C/A Page 24 of 24 Report No: ES181024030W Ver.1.0


Document Created: 2018-11-23 11:49:46
Document Modified: 2018-11-23 11:49:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC