RF Test Report

FCC ID: 2AIKWR-2

Test Report

Download: PDF

FCCID_3790876

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

FCC TEST REPORT

FOR

Evolve Skateboards PTY LTD

electric skateboard remote controller

Test Model: R-2

Prepared for : Evolve Skateboards PTY LTD
Address : 6/38 Kendor St Arundel, Gold Coast, QLD, Australia

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd
Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue,
Bao’an District, Shenzhen, Guangdong, China
Tel : (+86)755-82591330
Fax : (+86)755-82591332
Web : www.LCS-cert.com
Mail : webmaster@LCS-cert.com

Date of receipt of test : March 06, 2017
sample
Number of tested samples : 1
Sample number : Prototype
Date of Test : December 07, 2017~February 04, 2018
Date of Report : February 04, 2018

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

FCC -- TEST REPORT

February 04, 2018
Test Report No. : LCS171205031AEA
Date of issue

Test Model.............................. : R-2

EUT......................................... : electric skateboard remote controller

Applicant............................... : Evolve Skateboards PTY LTD

Address.................................. : 6/38 Kendor St Arundel, Gold Coast, QLD, Australia

Telephone............................... : /
Fax.......................................... : /

Manufacturer........................ : Evolve Skateboards PTY LTD

Address................................... : 6/38 Kendor St Arundel, Gold Coast, QLD, Australia

Telephone............................... : /

Fax.......................................... : /

Factory................................... : Evolve Skateboards PTY LTD
Address................................... : 6/38 Kendor St Arundel, Gold Coast, QLD, Australia

Telephone............................... : /

Fax.......................................... : /

Test Result Positive
The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

Revision History

Revision Issue Date Revisions Revised By
000 February 04, 2018 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

TABLE OF CONTENTS

1. GENERAL INFORMATION .......................................................................................... 6
1.1. Description of Device (EUT) .............................................................................................. 6
1.2. Support Equipment List ...................................................................................................... 6
1.3. External I/O .......................................................................................................................... 6
1.4. Description of Test Facility ................................................................................................ 6
1.5. Statement of the measurement uncertainty.................................................................... 7
1.6. Measurement Uncertainty.................................................................................................. 7
1.7. Description Of Test Modes ................................................................................................ 8
2. TEST METHODOLOGY ................................................................................................ 9
2.1. EUT Configuration .............................................................................................................. 9
2.2. EUT Exercise ....................................................................................................................... 9
2.3. General Test Procedures................................................................................................... 9
3. CONNECTION DIAGRAM OF TEST SYSTEM....................................................... 10
3.1. Justification ........................................................................................................................ 10
3.2. EUT Exercise Software .................................................................................................... 10
3.3. Special Accessories.......................................................................................................... 10
3.4. Block Diagram/Schematics ............................................................................................. 10
3.5. Equipment Modifications .................................................................................................. 10
3.6. Test Setup .......................................................................................................................... 10
4. SUMMARY OF TEST RESULTS ............................................................................... 11
5. ANTENNA REQUIREMENT ....................................................................................... 12
5.1. Standard Applicable.......................................................................................................... 12
5.2. Antenna Connected Construction .................................................................................. 12
6. RADIATED EMISSION MEASUREMENT................................................................ 13
6.1. Standard Applicable.......................................................................................................... 13
6.2. Instruments Setting ........................................................................................................... 13
6.3. Test Procedure .................................................................................................................. 14
6.4. Block Diagram of Test Setup .......................................................................................... 18
6.5. Test Results ....................................................................................................................... 19
6.6. Results for Radiated Emissions (Above 1GHz) ........................................................... 21
6.7. AC Power line conducted emissions .............................................................................. 22
6.8. Results for Band edge Testing (Radiated).................................................................... 24
7. 20 DB BANDWIDTH MEASUREMENT .................................................................... 25
7.1. Standard Applicable.......................................................................................................... 25
7.2. Block Diagram of Test Setup .......................................................................................... 25
7.3. Test Procedure .................................................................................................................. 25
7.4. Test Results ....................................................................................................................... 26
8. SUMMARY OF TEST EQUIPMENT.......................................................................... 28
9. TEST SETUP PHOTOGRAPHS ................................................................................ 29
10. EXTERNAL AND INTERNAL PHOTOS OF THE EUT........................................ 29

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

1.5. Statement of the measurement uncertainty
The data and results referenced in this document are true and accurate. The
reader is cautioned that there may be errors within the calibration limits of the
equipment and facilities. The measurement uncertainty was calculated for all
measurements listed in this test report acc. To CISPR 16 – 4 “Specification for
radio disturbance and immunity measuring apparatus and methods – Part 4:
Uncertainty in EMC Measurements” and is documented in the LCS quality
system acc. To DIN EN ISO/IEC 17025. Furthermore, component and process
variability of devices similar to that tested may result in additional deviation.
The manufacturer has the sole responsibility of continued compliance of the
device.

1.6. Measurement Uncertainty
Test Item Frequency Range Uncertainty Note
9KHz~30MHz 3.10dB (1)
30MHz~200MHz 2.96dB (1)
Radiation Uncertainty :
200MHz~1000MHz 3.10dB (1)
1GHz~26.5GHz 4.00dB (1)
Conduction : 150kHz~30MHz 1.63dB (1)
Uncertainty
Power disturbance : 30MHz~300MHz 1.60dB (1)

(1). This uncertainty represents an expanded uncertainty expressed at
approximately the 95% confidence level using a coverage factor of k=2.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

1.7. Description Of Test Modes

The EUT operates in the unlicensed ISM band at 2.4GHz. The following
operating modes were applied for the related test items.

All test modes were tested, only the result of the worst case was recorded in
the report.
It was pre-tested on the positioned of each 3 axis. The worst case was found
positioned on X-plane.

Mode of Operations Transmitting Frequency
(MHz)
2456
GFSK 2468
2480
For Conducted Emission
Test Mode TX Mode
For Radiated Emission
Test Mode TX Mode

Worst-case mode and channel used for 150kHz-30 MHz power line conducted
emissions was the mode and channel with the highest output power, that was
determined to be TX-2402MHz.

Worst-case mode and channel used for 9kHz-1000 MHz radiated emissions
was the mode and channel with the highest output power, that was determined
to be TX-2402MHz.

***Note: Using a temporary antenna connector for the EUT when the conducted
measurements are performed.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

2. TEST METHODOLOGY
All measurements contained in this report were conducted with ANSI C63.10:
2013, American National Standard of Procedures for Compliance Testing of
Unlicensed Wireless Devices.
The radiated testing was performed at an antenna-to-EUT distance of 3 meters.
All radiated and conducted emissions measurement was performed at
Shenzhen LCS Compliance Testing Laboratory Ltd..

2.1. EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement
to meet the Commissions requirement and operating in a manner that intends
to maximize its emission characteristics in a continuous normal application.

2.2. EUT Exercise
The EUT was operated in the engineering mode to fix the TX frequency that
was for the purpose of the measurements.
According to its specifications, the EUT must comply with the requirements of
the Section 15.203, 15.205, 15.207, 15.209 and 15.249 under the FCC Rules
Part 15 Subpart C.

2.3. General Test Procedures
2.3.1 Conducted Emissions
According to the requirements in Section 6.2 of ANSI C63.10: 2013, AC
power-line conducted emissions shall be measured in the frequency range
between 0.15 MHz and 30MHz using Quasi-peak and average detector modes.

2.3.2 Radiated Emissions
The EUT is placed on a turn table and the turntable shall rotate 360 degrees to
determine the position of maximum emission level. EUT is set 3m away from
the receiving antenna, which varied from 1m to 4m to find out the highest
emission. And also, each emission was to be maximized by changing the
polarization of receiving antenna both horizontal and vertical. In order to find
out the maximum emissions, exploratory radiated emission measurements
were made according to the requirements in Section 6.3 of ANSI C63.10: 2013

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

3. CONNECTION DIAGRAM OF TEST SYSTEM

3.1. Justification
The system was configured for testing in a continuous transmit condition.

3.2. EUT Exercise Software
N/A

3.3. Special Accessories
N/A

3.4. Block Diagram/Schematics
Please refer to the related document

3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any
modification on the EUT.

3.6. Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

4. SUMMARY OF TEST RESULTS

FCC Rules Description Of Test Result

§15.203 Antenna Requirement Compliant

§15.207(a) Power Line Conducted Emissions Compliant
§15.205(a),
Radiated Emissions
§15.209(a), Compliant
Measurement
§15.249(a), §15.249(c)
§15.249 Band Edges Measurement Compliant

§15.249, §15.215 20 dB Bandwidth Compliant

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 11 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

5. ANTENNA REQUIREMENT

5.1. Standard Applicable
According to § 15.203, An intentional radiator shall be designed to ensure that
no antenna other than that furnished by the responsible party shall be used
with the device. The use of a permanently attached antenna or of an antenna
that uses a unique coupling to the intentional radiator shall be considered
sufficient to comply with the provisions of this section. The manufacturer may
design the unit so that a broken antenna can be replaced by the user, but the
use of a standard antenna jack or electrical connector is prohibited.

5.2. Antenna Connected Construction
The gains of antenna used for transmitting is 2.5dBi, and the antenna is
connect to PCB board and no consideration of replacement. Please see EUT
photo for details.

Result: Compliance.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

6. RADIATED EMISSION MEASUREMENT

6.1. Standard Applicable
Emissions radiated outside of the specified frequency bands, except for
harmonics, shall be attenuated by at least 50 dB below the level of the
fundamental or to the general radiated emission limits in §15.209, whichever is
the lesser attenuation.
20dBc in any 100 kHz bandwidth outside the operating frequency band. In case
the emission fall within the restricted band specified on 15.205(a), then the
15.209(a) and 15.249 limit in the table below has to be followed.

Fundamental Field Strength of fundamental Field Strength of harmonics
Frequency (millivolts/meter) (microvolts/meter)
902-928MHz 50 500
2400-2483.5MHz 50 500

5725-5875MHz 50 500

24.0-24.25GHz 250 2500

Frequencies Field Strength Measurement Distance
(MHz) (microvolts/meter) (meters)
0.009~0.490 2400/F(KHz) 300
0.490~1.705 24000/F(KHz) 30
1.705~30.0 30 30
30~88 100 3
88~216 150 3
216~960 200 3
Above 960 500 3

6.2. Instruments Setting
The following table is the setting of spectrum analyzer and receiver.

Spectrum Parameter Setting
Attenuation Auto
Start ~ Stop Frequency 9kHz~150kHz / RB 200Hz for QP
Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP
Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

Spectrum Parameter Setting
Attenuation Auto
Start Frequency 1000 MHz
Stop Frequency 10th carrier harmonic
RB / VB (Emission in restricted band) 1MHz / 1MHz for Peak, 1 MHz / 10Hz for Average
RB / VB (Emission in non-restricted band) 1000KHz / 1000KHz for peak

6.3. Test Procedure
1) Sequence of testing 9 kHz to 30 MHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the
user manual or described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation
conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet
below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna height is 0.8 meter.
--- At each turntable position the analyzer sweeps with peak detection to find
the maximum of all emissions
Final measurement:
--- Identified emissions during the premeasurement the software maximizes by
rotating the turntable position (0°to 360°) and by rotating the elevation axes (0°
to 360°).
--- The final measurement will be done in the position (turntable and elevation)
causing the highest emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position,
correction factor, margin to the limit and limit will be recorded. Also a plot with
the graph of the premeasurement and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 14 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

2) Sequence of testing 30 MHz to 1 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the
user manual or described by manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is
placed on the ground plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with
insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation
conditions
--- The AC power port of the EUT (if available) is connected to a power outlet
below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer
sweeps three times in peak to find the maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest
peaks.
--- According to the maximum antenna and turntable positions of
premeasurement the software maximize the peaks by changing turntable
position (± 45°) and antenna movement between 1 and 4 meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height,
antenna polarization, turntable angle, correction factor, margin to the limit and
limit will be recorded. Also a plot with the graph of the premeasurement with
marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

3) Sequence of testing 1 GHz to 18 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the
user manual or described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with
insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation
conditions
--- The AC power port of the EUT (if available) is connected to a power outlet
below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height is 1.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with
peak detection to find the maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest
peaks.
--- According to the maximum found antenna polarisation and turntable position
of the premeasurement the software maximizes the peaks by rotating the
turntable position (0°to 360°). This measurement is repeated for different
EUT-table positions (0°to 150°in 30°-steps). This procedure is repeated for
both antenna polarisations.
--- The final measurement will be done in the position (turntable, EUT-table and
antenna polarization) causing the highest emissions with Peak and RMS
detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position,
EUT-table position, antenna polarization, correction factor, margin to the limit
and limit will be recorded. Also a plot with the graph of the premeasurement
with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 16 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

4) Sequence of testing above 18 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the
user manual or described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with
insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation
conditions
--- The AC power port of the EUT (if available) is connected to a power outlet
below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.
Premeasurement:
--- The antenna is moved spherical over the EUT in different polarisations of
the antenna.
Final measurement:
--- The final measurement will be performed at the position and antenna
orientation for all detected emissions that were found during the
premeasurements with Peak and RMS detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor,
margin to the limit and limit will be recorded. Also a plot with the graph of the
premeasurement and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 17 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

6.5. Test Results
Results of Radiated Emissions (9kHz~30MHz)

Frequency Level Over Limit Over Limit
Remark
(MHz) (dBuV) (dB) (dBuV)
- - - - See Note
Note:
The radiated emissions from 9kHz to 30MHz are at least 20dB below the
official limit and no need to report.
Distance extrapolation factor = 40 log (specific distance / test distance) (dB);
Limit line = specific limits (dBuV) + distance extrapolation factor.

Results of Radiated Emissions (30MHz~1000MHz)

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 19 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

6.6. Results for Radiated Emissions (Above 1GHz)
Field Strength Of Fundamental (TX-2456MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2456.00 H 91.35 81.24 114 94 Pass
2456.00 V 90.43 80.46 114 94 Pass

Ant. Pre. Cab.
Freq. Reading Measured Limit Margin
Fac Fac. Loss Remark Pol.
MHz dBuv dBuv/m dBuv/m dB
dB/m dB dB
4912.00 54.47 33.26 35.14 3.98 56.57 74.00 -17.43 Peak Horizontal
4912.00 38.74 33.26 35.14 3.98 40.84 54.00 -13.16 Average Horizontal
4912.00 58.43 33.26 35.14 3.98 60.53 74.00 -13.47 Peak Vertical
4912.00 41.38 33.26 35.14 3.98 43.48 54.00 -10.52 Average Vertical

Field Strength Of Fundamental (TX-2468MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2468.00 H 91.07 81.46 114 94 Pass
2468.00 V 89.86 80.34 114 94 Pass

Ant. Pre. Cab.
Freq. Reading Measured Limit Margin
Fac Fac. Loss Remark Pol.
MHz dBuv dBuv/m dBuv/m dB
dB/m dB dB
4936.00 54.16 33.3 35.16 3.98 56.28 74.00 -17.72 Peak Horizontal
4936.00 38.68 33.3 35.16 3.98 40.80 54.00 -13.20 Average Horizontal
4936.00 59.32 33.3 35.16 3.98 61.44 74.00 -12.56 Peak Vertical
4936.00 41.80 33.3 35.16 3.98 43.92 54.00 -10.08 Average Vertical

Field Strength Of Fundamental (TX-2480MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2480.00 H 89.98 80.21 114 94 Pass
2480.00 V 89.69 80.04 114 94 Pass

Ant. Pre. Cab.
Freq. Reading Measured Limit Margin
Fac Fac. Loss Remark Pol.
MHz dBuv dBuv/m dBuv/m dB
dB/m dB dB
4960.00 55.01 33.31 35.16 3.98 57.14 74.00 -16.86 Peak Horizontal
4960.00 39.29 33.31 35.16 3.98 41.42 54.00 -12.58 Average Horizontal
4960.00 58.25 33.31 35.16 3.98 60.38 74.00 -13.62 Peak Vertical
4960.00 41.94 33.31 35.16 3.98 44.07 54.00 -9.93 Average Vertical

Notes:
1. Measuring frequencies from 9k~10th harmonic (ex. 26GHz), No emission found between lowest internal
used/generated frequency to 30MHz.
2. Radiated emissions measured in frequency range from 9k~10th harmonic (ex. 26GHz) were made with an
instrument using Peak detector mode.
3. No emission was be recorded above 18GHz means the reading of emissions are attenuated more than 20dB
below the permissible limits or the field strength is too small to be measured.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 21 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

6.7. AC Power line conducted emissions
6.7.1 Standard Applicable

According to §15.207 (a): For an intentional radiator which is designed to be connected to the public
utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on
any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed 250 microvolts
(The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz).
The limits at specific frequency range is listed as follows:

Frequency Range Limits (dBμV)
(MHz) Quasi-peak Average
0.15 to 0.50 66 to 56 56 to 46
0.50 to 5 56 46
5 to 30 60 50

* Decreasing linearly with the logarithm of the frequency

6.7.2 Block Diagram of Test Setup
Vert. reference
plane

EMI receiver

EUT
PC

LISN Reference ground plane

6.7.3 Test Results

PASS.
The test data please refer to following page.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 22 of 29

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AIKWR-2 Report No.: LCS171205031AEA

9. TEST SETUP PHOTOGRAPHS
Please refer to separated files for Test Setup Photos of the EUT

10. EXTERNAL AND INTERNAL PHOTOS OF THE EUT

Please refer to separated files for External and internal Photos of the EUT

-----------THE END OF REPORT----------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 29

Document Created: 2018-03-21 14:52:11
Document Modified: 2018-03-21 14:52:11

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC