User Manual

FCC ID: 2AH4HATD300S

Users Manual

Download: PDF
FCCID_3902121

Mobilogix ATD300S Module Assembly Summary: www.mobilogix.com

Mobilogix ATD300S Module Assembly Detail: Cut a 45mm piece of double sided tape and place inside white rectangle Place battery on double sided tape with protection circuit facing end of board. Place foam on top of battery Keep battery within white rectangle USB connector Make sure wire leads are on the same side as USB connector Protection circuit 5500 Trabuco Road, Suite 150, Irvine, CA 92620 Tel: (949) 748-8895 Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc. Other registered trademarks that appear on this brochure are the property of the respective owners © 2017 Mobilogix, Inc.

Mobilogix ATD300S Place board with battery stack-up on bottom piece of enclosure. Secure with Place metal plate inside 5 screws. Light pipes groove located on bottom piece of enclosure Don’t plug in battery connector until PCB is when putting enclosure Bottom piece of together, light pipes go on top screwed down enclosure of PCB LEDS Use 6 of the same screws as used for PCB to secure enclosure 5500 Trabuco Road, Suite 150, Irvine, CA 92620 Tel: (949) 748-8895 Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc. Other registered trademarks that appear on this brochure are the property of the respective owners © 2017 Mobilogix, Inc.

Mobilogix ATD300S FCC Interference Statement (Part 15.105 (b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Part 15 Clause 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Part 15.19(a) [interference compliance statement], unless the following statement is already provided on the device label This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 5500 Trabuco Road, Suite 150, Irvine, CA 92620 Tel: (949) 748-8895 Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc. Other registered trademarks that appear on this brochure are the property of the respective owners © 2017 Mobilogix, Inc.

Mobilogix ATD300S ISED RSS-Gen Notice This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. FCC RF Exposure Guidance Statement In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times. ISED RF Exposure Guidance Statement In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times. Afin de se conformer aux exigences d'exposition RF FCC / ISED, cet appareil doit être installé pour fournir au moins 20 cm de séparation du corps humain en tout temps. 5500 Trabuco Road, Suite 150, Irvine, CA 92620 Tel: (949) 748-8895 Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc. Other registered trademarks that appear on this brochure are the property of the respective owners © 2017 Mobilogix, Inc.

Mobilogix ATD300S Powering ON and OFF Power ON • When battery is connected, the device automatically powers on. The device does not have a button or power switch. The ATD300S Asset Tracking Device will be mounted on top of a host device, which will supply power to charge the internal battery. Power OFF • When the ATD300S Asset Tracking Device is in an idle state, it enters into its lowest power consumption state, or low power mode. 5500 Trabuco Road, Suite 150, Irvine, CA 92620 Tel: (949) 748-8895 Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc. Other registered trademarks that appear on this brochure are the property of the respective owners © 2017 Mobilogix, Inc.

Mobilogix ATD300S Key Hardware Components and Specifications Hardware Components and Specifications Component/Spec Description Quectel EC21-V modem • Qualcomm MDM 9307 chipset • LTE CAT1 • 3GPP Rel. 11 • FOTA • Embedded GPS/GNSS Antennas Embedded Cellular/GNSS/Bluetooth SIM card slot 3FF Verizon SIM Power ON/OFF Powered by Lithium Polymer battery Battery Rechargeable Lithium Polymer • 3.7V • 2000mAh Charging Internal battery will be charged by host power supply Operating temperature -20°C to +85°C Dimensions 138.50 x 69.50 x 31mm Certifications FCC/IC/Verizon 5500 Trabuco Road, Suite 150, Irvine, CA 92620 Tel: (949) 748-8895 Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc. Other registered trademarks that appear on this brochure are the property of the respective owners © 2017 Mobilogix, Inc.


Document Created: 2018-05-29 11:55:43
Document Modified: 2018-05-29 11:55:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC