User manual

FCC ID: 2AEUPBHADV001

Users Manual

Download: PDF
FCCID_4337974

108.0 mm 118.0 mm

T Le————— uW 0‘gq —————»I . iI Before you begin i Chedk out howitalits together. } 1.fromt ce i i | 5 vewertube 2. hont ce 6 herconr 4.tewerlans ~—————_ rotpicusd) Aritbaton



You may have to remove excess paint in arder to unscrew your peeghole (f noy, skip ahead). Check for paint on or around your peephole, both indoors and outdoors. Use the sharp side of the included tool to carefuly remove any paint covering the edge or the slots.

Remove indoor half. Remove outdoorhalf. On the indoor side, place the flat edge of the The outdoor portion included tool in the slots and rotate counter— should slide right out. clackwise to unscrew the peephole. If not, check again for paint or other Once it‘loose enough, you can use your fingers obstructions around to finish unserewing it and removeit completely the lens. Ifthis isn‘tyour forever home, store the peephole in safe plece in case you have to re—installitlater. voomephemtomess bwomoctinoite rectcieuniauntemana buirderpetoninn t fomprang

Let‘s find out for sure. Try to place the adapterinto the hole on the inside of your doorto see if t fits. IF it fits, insert it allthe If t doen‘t ft, that‘s way into the hole. fine. You don‘t needit. moomg)

Place the outdoor Remove the rear cover. assembly. Grasp the thin edge of the indoor assembly body, From the front side of and pinch the cover at the indlentations. Pull to your door, feed the metal separate. You can set the cover aside for now. tube and black wire through the hole until your Door View Cam is 4 flush with the door. 14 is

Place the indoor Remove the connector cable. assembly. We tucked itinto the matal tubefor safe travels, Next, carefuly se but now it‘stime to take it out. the indoorassembly Grasp either side of the exposed plastic tab, then onto the metal tube delicately draw it out of the tube untll there‘s no until it‘ flush with the more slack left. door, making sure the outdoor assembly lsn‘t pushed out of your door. Wimytomitoitin crtnermentizegione hn Hhom ns ociyucts

Join indoor and outdoor assemblies. Plug in the connector. With the cable out Gently pull the cable taught, then press the of the way, nlace the connector into the port on the indoor assembly. plastictightening nut into the hole and over the metal tube. Twist cloclwise to tighten. You can use the included tool or your fingers. Once secure, chack the outdoor assembly. it mayrotate sightly while tightening, so make sure it‘s level.

Secure the cable. Insert the battery. Guide the plastic tab with the arrow into Slide the charged battery into the bottom of your the channe} and slide it down to secure the Door View Cam until t clicks into place (don‘t put remaining slack in the cable. the coverback on just yet) m

Complete setup in the Ring app. Cover it up. In the Ring app, select Sat Up a Device and Once in—app setup is complete, place the cover follow the in—app instructions. back anto your Door View Cam untilit licks. Youreall sett Blue light flashing? If the light on the front af your Door View Cam is flashing after setup,it‘s updating its software. Be not remove the battery from your Door View Cam while the light is flashing!

JSBK00622

1523 26th St. Santa Monica, CA 90404 This device, the Ring Door View Cam, complies with Part 15 of the U.S. Federal Communications Commission Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications to this equipment not authorized by Ring LLC may void its approval for operation. The radio transmitter in this device has been approved under the FCC and IC numbers shown on the device. Other digital circuitry in this device has been approved under a supplier’s declaration of conformity (SDoC). Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To comply with FCC guidelines limiting exposure to radio frequency energy, this equipment should be installed and operated with minimum distance 20 cm between the radiator and your body and must not be co-located or operated in conjunction with any other antenna or transmitter. NOTE: This equipment has been tested and found to comply with relevant FCC requirements, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Additional information regarding the Ring Door View Cam FCC equipment authorization(s) can be found at: ring.com/regulatory To contact Ring about the device’s FCC equipment authorization, please write us at the address shown below or contact us using the following address: legal@ring.com Use the provided battery and follow instructions in the installation manual for charging and inserting the battery. Replace only with Lithium-Ion batteries designed specifically for use in this product. Do not dispose of batteries in fire. Batteries should be recycled or disposed of as per state and local guidelines. Ring 1523 26th St. Santa Monica, CA 90404 © 2019 Ring LLC or its affiliates. Ring and all related logos are trademarks of Amazon.com, Inc. or its affiliates. 04_Door_View_Cam_LEGAL.indd 1 5/2/19 3:45 PM

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help.


Document Created: 2019-06-18 17:36:00
Document Modified: 2019-06-18 17:36:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC