RF Test Report -WIFI

FCC ID: 2AEUPBHADV001

Test Report

Download: PDF
FCCID_4337959

( ntl Report Number: 1905FR27 \-’ Rev.01 RF Test Report Applicant : Ring LLC Product Type : Door View Cam Trade Name : Ring Model Number : G63RIA Applicable Standard : FCC 47 CFR PART 15 SUBPART C ANSI C63.10:2013 Receive Date : Apr. 08, 2019 Test Period : Mar. 13 ~ Mar. 15, 2019 Issue Date : Jun. 13, 2019 Issue by A Test Lab Techno Corp. No. 140—1, Changan Street, Bade District, neuck (IA\F) Taoyuan City 33465, Taiwan (R.O.C.) x t § mmans Tel : +886—3—2710188 / Fax : +886—3—2710190 Taiwan Accreditation Foundation accreditation number: 1330 Test Firm MRA designation number: TWOO10 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision—section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. 1 of 20

Report Number: 1905FR27 Rev.01 Revision History Rev. Issue Date Revisions Revised By 00 May 22, 2019 Initial Issue Nina Lin 01 Jun. 13, 2019 Page 17 & 18 Added Test Photographs. Nina Lin 2 of 20

( ntl Report Number: 1905FR27 \-’ Rev.01 Verification of Compliance Issued Date: Jun. 13, 2019 Applicant : Ring LLC Product Type : Door View Cam Trade Name : Ring Model Number I— GB3ROA FCC ID : 2AEUPBHADVOO1 EUT Rated Voltage : DC 3.6 V or DC 3.65 V, 6040 mAh Test Voltage : DC 3.65 V Applicable Standard _: FCC 47 CFR PART 15 SUBPART C ANSI C63.10:2013 Test Result : Complied Performing Lab. : A Test Lab Techno Corp. «19 . . SAAA No. 140—1, Changan Street, Bade District, m Tacyuan City 33465, Taiwan (R.O.C.) ',//Zib\ Ahitebi® Tel : +886—3—2710188 / Fax : +886—3—2710190 Taiwan Accreditation Foundation accreditation number: 1330 hitp://www.atl—lab.com.tw/e—index.htm A Test Lab Techno Corp. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by A Test Lab Techno Corp. based on interpretations and/or observations of test results. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Approved By ifi'\/ ‘ [ Reviewed By EJ/((C Ou i/q_ngz M + C (Manager) <_(Fly Lu) (Testing Engineer) (Eric Ou Yang) 3 of 20

Report Number: 1905FR27 Rev.01 TABLE OF CONTENTS 1 General Information ......................................................................................................... 5 1.1. Summary of Test Result ............................................................................................. 5 1.2. Measurement Uncertainty .......................................................................................... 6 2 EUT Description................................................................................................................ 7 3 Test Methodology ............................................................................................................. 8 3.1. Mode of Operation ...................................................................................................... 8 3.2. EUT Test Step............................................................................................................. 8 3.3. Configuration of Test System Details .......................................................................... 9 3.4. Test Instruments ....................................................................................................... 10 3.5. Test Site Environment............................................................................................... 10 4 Measurement Procedure ................................................................................................ 11 4.1. Radiated Emission Measurement ............................................................................. 11 4.2. Maximum Conducted Output Power Measurement .................................................. 15 4.3. Antenna Measurement ............................................................................................. 15 5 Test Results .................................................................................................................... 16 Annex A. Conducted Test Results .................................................................................... 16 Annex B. Radiated Emission Measurement ..................................................................... 17 4 of 20

Report Number: 1905FR27 Rev.01 1 General Information 1.1. Summary of Test Result Standard Item Result Remark FCC 15.207 AC Power Conducted Emission N/A Note1 15.247(d) Transmitter Radiated Emissions PASS Note2 15.247(b)(3) Max. Output Power PASS ----- 15.247(a)(2) 6 dB RF Bandwidth N/A Note1 15.247(e) Maximum Power Spectral Density N/A Note1 Out of Band Conducted Spurious 15.247(d) N/A Note1 Emission 15.203 Antenna Requirement PASS ----- The test results of this report relate only to the tested sample(s) identified in this report. Note1: C2PC No need for verification. Note2: Transmitter Radiated Emissions is tested using the Harmonic worst Mode 2(2462 MHz). Standard Description CFR47, Part 15, Subpart C Intentional Radiators American National Standard of Procedures for Compliance Testing of ANSI C63. 10: 2013 Unlicensed Wireless Devices GUIDANCE FOR COMPLIANCE MEASUREMENTS ON DIGITAL KDB 558074 D01 15.247 TRANSMISSION SYSTEM, FREQUENCY HOPPING SPREAD Meas Guidance v05r02 SPECTRUM SYSTEM, AND HYBRID SYSTEM DEVICES OPERATING UNDER SECTION 15.247 OF THE FCC RULES 5 of 20

Report Number: 1905FR27 Rev.01 1.2. Measurement Uncertainty Test Item Frequency Range Uncertainty (dB) 9 kHz ~ 150 kHz 2.7 Conducted Emission 150 kHz ~ 30 MHz 2.7 9 kHz ~ 30 MHz 1.7 30 MHz ~ 1000 MHz 5.7 Radiated Emission 1000 MHz ~ 18000 MHz 5.5 18000 MHz ~ 26500 MHz 4.8 26500 MHz ~ 40000 MHz 4.8 Conducted Output Power +0.27 dB / -0.28 dB RF Bandwidth 4.96 % Power Spectral Density +0.71 dB / -0.77 dB 6 of 20

@l Report Number: 1905FR27 Rev.o1 2 EUT Description Appleant Ring LC 1523 26th Street, Sente Monics CA 80404, United States Menufecturer :esnga ‘;;m Street, Sante Monics CA 80404, United States Product Type Door View Cam Trade Name Ring Made! Number cesroa reeio zAeupeHianvoot Class II Permissive Change Change the main bosrd, camera board and the appesrance Operate Frea. Band Freq“m:fi”ge Modulation BCE:ZCLT;‘” ADDD/EBt;DR(E;t\E(ns] ieee 802. 110 2412 — 2002 psss 20 MHz Up to 11 Mbps eee s02. 19 2412— 202 orom 20 MHz Up to 54 Mbps ieEE 802.tin 24 GHez 20 MHz 2412— 2402 orom 20 MHz |_Up to 722 Mps Type Max. GeintaBi) Antenna informstion PIFA Anterns 2.78 Antenns Delvery See section 3.1 Operate Temp. Range 40— «50 ‘c Frequency Band Max. RF ?\;Jvt]putpuwer ieee 202 tmb avet ieee 202 110 over iEEE 802. t1n 24 GHe 20 Mz oo 7 of 20

Report Number: 1905FR27 Rev.01 3 Test Methodology 3.1. Mode of Operation Decision of Test ATL has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Test Mode Mode 1: Transmit mode Mode 2: IEEE 802.11b Continuous TX mode Mode 3: IEEE 802.11g Continuous TX mode Mode 4: IEEE 802.11n 2.4 GHz 20 MHz Continuous TX mode Software used to control the EUT for staying in continuous transmitting mode was programmed. After verification, all tests were carried out with the worst case test modes. By preliminary testing and verifying three axis (X, Y and Z) position of EUT transmitted status, it was found that “X axis” position was the worst, then the final test was executed the worst condition and test data were recorded in this report. Data Rate Test Mode Antenna Delivery Test Channel (Mbps) Mode 2 1TX 1 1, 6, 11 Mode 3 1TX 6 1, 6, 11 Mode 4 1TX 6.5 1, 6, 11 3.2. EUT Test Step 1. Setup the EUT shown on “Configuration of Test System Details”. 2. Turn on the power of all equipment. 3. Turn Wi-Fi function link to AP. 4. EUT run test program. Measurement Software No. Description Software Version 1 Radiated Emission EZ EMC 1.1.4.4 8 of 20

Report Number: 1905FR27 Rev.01 3.3. Configuration of Test System Details Radiated Emission EUT Devices Description Product Manufacturer Model Number Serial Number Power Cord (1) --- --- --- --- --- 9 of 20

Report Number: 1905FR27 Rev.01 3.4. Test Instruments For Radiated Emissions Test Period: May 13, 2019 Equipment Manufacturer Model Number Serial Number Cal. Date Cal. Period Spectrum Analyzer Keysight N9010A MY52221312 01/14/2019 1 year (10 Hz~44 GHz) Pre Amplifier Agilent 8449B 3008A02237 10/16/2018 1 year (1~26.5 GHz) Pre Amplifier Agilent 8447D 2944A11119 01/14/2019 1 year (100 kHz~1.3 GHz) Broadband Antenna Schwarzbeck VULB9168 416 10/19/2018 1 year Horn Antenna SCHWARZBECK BBHA9120D 9120D-550 08/23/2018 1 year (1~18 GHz) MESS-ELEKTRONIK Horn Antenna SCHWARZBECK BBHA9170 9170-320 08/07/2018 1 year (18~40 GHz) MESS-ELEKTRONIK COM-POWER Loop Antenna AL-130 121014 03/29/2019 1 year CORPORATION RF Cable EMCI EMC104-N-N-6000 TE01-1 02/20/2019 1 year EMC104-SM-SM-1 Microwave Cable EMCI 170814 10/30/2018 1 year 3000 EMC102-KM-KM-1 Microwave Cable EMCI 151001 02/20/2019 1 year 4000 For Conducted Test Period: May 15, 2019 Equipment Manufacturer Model Number Serial Number Cal. Date Cal. Period Power Sensor Anritsu MA2411B 1126022 08/29/2018 1 year Power Meter Anritsu ML2495A 1135009 08/29/2018 1 year EMC102-SM-SM15 Microwave Cable EMCI 001 11/21/2018 1 year 00 Test Site ATL TE05 TE05 N.C.R. ----- Note: N.C.R. = No Calibration Request. 3.5. Test Site Environment Items Required (IEC 60068-1) Actual Temperature (C) 15-35 26 Humidity (%RH) 25-75 60 Barometric pressure (mbar) 860-1060 990 10 of 20

Report Number: 1905FR27 Rev.01 4 Measurement Procedure 4.1. Radiated Emission Measurement  Limit According to §15.209(a), except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (μV/m at meter) (meters) 0.009 – 0.490 2400 / F (kHz) 300 0.490 – 1.705 24000 / F (kHz) 30 1.705 – 30.0 30 30 30 - 88 100** 3 88-216 150** 3 216-960 200** 3 Above 960 500 3 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241.  Setup 9 kHz ~ 30 MHz 11 of 20

Report Number: 1905FR27 Rev.01 Below 1 GHz Above 1 GHz 12 of 20

Report Number: 1905FR27 Rev.01  Test Procedure Final radiation measurements were made on a three-meter, Semi Anechoic Chamber. The EUT system was placed on a nonconductive turntable which is 0.8 or 1.5 meters height, top surface 1.0 x 1.5 meter. The spectrum was examined from 250 MHz to 2.5 GHz in order to cover the whole spectrum below 10th harmonic which could generate from the EUT. During the test, EUT was set to transmit continuously & Measurements spectrum range from 9 kHz to 26.5 GHz is investigated. For measurements below 1 GHz the resolution bandwidth is set to 100 kHz for peak detection measurements or 120 kHz for quasi-peak detection measurements. Peak detection is used unless otherwise noted as quasi-peak. For measurements above 1 GHz the resolution bandwidth is set to 1 MHz, and then the video bandwidth is set to 3 MHz for peak measurements and 10 Hz for average measurements when Duty cycle >0.98 / 1/T for average measurements when Duty cycle <0.98. A nonconductive material surrounded the EUT to supporting the EUT for standing on tree orthogonal planes. At each condition, the EUT was rotated 360 degrees, and the antenna was raised and lowered from one to four meters to find the maximum emission levels. Measurements were taken using both horizontal and vertical antenna polarization. SCHWARZBECK MESS-ELEKTRONIK Biconilog Antenna at 3 Meter and the SCHWARZBECK Double Ridged Guide Antenna was used in frequencies 1 –26.5 GHz at a distance of 3 meter. The antenna at an angle toward the source of the emission. All test results were extrapolated to equivalent signal at 3 meters utilizing an inverse linear distance extrapolation Factor (20 dB/decade). For testing above 1 GHz, the emission level of the EUT in peak mode was 20 dB lower than average limit (that means the emission level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. Appropriate preamplifiers were used for improving sensitivity and precautions were taken to avoid overloading or desensitizing the spectrum analyzer. No post – detector video filters were used in the test. The spectrum analyzer’s 6 dB bandwidth was set to 1 MHz, and the analyzer was operated in the peak detection mode, for frequencies both below and up 1 GHz. The average levels were obtained by subtracting the duty cycle correction factor from the peak readings. The following procedures were used to convert the emission levels measured in decibels referenced to 1 microvolt (dBuV) into field intensity in micro volts pre meter (uV/m). The actual field intensity in decibels referenced to 1 microvolt in to field intensity in micro colts per meter (dBuV/m). 13 of 20

Report Number: 1905FR27 Rev.01 The actual field is intensity in referenced to 1 microvolt per meter (dBuV/m) is determined by algebraically adding the measured reading in dBuV, the antenna factor (dB), and cable loss (dB) and Subtracting the gain of preamplifier (dB) is auto calculate in spectrum analyzer. (1) Amplitude (dBuV/m) = FI (dBuV) +AF (dBuV) +CL (dBuV)-Gain (dB) FI= Reading of the field intensity. AF= Antenna factor. CL= Cable loss. P.S Amplitude is auto calculate in spectrum analyzer. (2) Actual Amplitude (dBuV/m) = Amplitude (dBuV)-Dis(dB) The FCC specified emission limits were calculated according the EUT operating frequency and by following linear interpolation equations: (a) For fundamental frequency : Transmitter Output < +30 dBm (b) For spurious frequency : Spurious emission limits = fundamental emission limit /10 Data of measurement within this frequency range without mark in the table above means the reading of emissions are attenuated more than 20 dB below the permissible limits or the field strength is too small to be measured. 14 of 20

Report Number: 1905FR27 Rev.01 4.2. Maximum Conducted Output Power Measurement  Limit For systems using digital modulation in the 2400-2483.5 MHz, the limit for maximum output power is 30 dBm. And According to 15.247 (b), if transmitting antennas of directional gain greater than 6 dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi.  Test Setup EUT Power Power Sensor Meter  Test Procedure The testing follows the Measurement Procedure of ANSI C63.10:2013 section 11.9.2.3.2 Method AVGPM. The tests below are run with the EUT’s transmitter set at high power in TX mode. The EUT is needed to force selection of output power level and channel number. While testing, EUT was set to transmit continuously. Remove the Subjective device’s antenna and connect the RF output port to power sensor. 4.3. Antenna Measurement  Limit For intentional device, according to 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And According to 15.247 (b), if transmitting antennas of directional gain greater than 6 dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi.  Antenna Description See section 2 – antenna information. 15 of 20

Report Number: 1905FR27 Rev.01 5 Test Results Annex A. Conducted Test Results Maximum Conducted Output Power Measurement Average Output Power Peak Output Power Frequency Test Mode Data Rate Measurement Results Measurement Results Limit (MHz) (dBm) (W) (dBm) (W) (W) 2412 14.89 0.031 16.92 0.049 ≤ 30 Mode 2 2437 1M 15.30 0.034 17.53 0.057 ≤ 30 2462 15.55 0.036 17.83 0.061 ≤ 30 2412 10.00 0.010 18.50 0.071 ≤ 30 Mode 3 2437 6M 14.84 0.030 19.85 0.097 ≤ 30 2462 10.16 0.010 18.45 0.070 ≤ 30 2412 10.02 0.010 18.63 0.073 ≤ 30 Mode 4 2437 6.5 M 14.00 0.025 19.74 0.094 ≤ 30 2462 10.05 0.010 18.45 0.070 ≤ 30 Note: The relevant measured result has the offset with cable loss already. 16 of 20

' ntl Report Number: 1905FR27 \’ Rev.01 Annex B. Radiated Emission Measurement Harmonic Below 1 GHz Standard FCG Part 15. 27 Test Distance 3m Test tem Harmonic Power DC 3.85 V Frequency 2462 MHz Temp (C)/Hum (%RH) 26(C)160 %RH Mode Mode 2 Ant.Polar Horizontal 500— sbwrm w r——— 0 30000 127.0 2240 321.00 410.00 515.00 612.00 70000 806.00 1000.00°Wfte No. Frequency. Reading Correct Factor Result Limi Margin Rematk hiz (aBuv) (dBim (dBuvim) (dBuvim) ta9) 1 172.se00 sess «27 s306 «3.s0 104 or 2 228.0100 «3s 33 3702 «5.00 «288 or s 270.2000 «184 «.09 3715 «5.00 «a85 or « se«.0500 seas «256 s5.602 «5.00 —10.38 or s «53.8000 se45 «o1 3754 «5.00 «248 or s 7es 000 s178 «85 sees «5.00 237 or Note:1. Result(dBuVim) = Correct Factor (dB/m) + Reading(dBu\) Example: 33.08 =—6.27 + 30.39 2Correction factor (dB/m) = Antenna Factor (dBfm) + Cable loss (d8) — Pre—Amplifier gain (dB) 3. When the peak resultsare less than average Iimit, so not need to evaluate the average 17 of 20

' ntl Report Number: 1905FR27 \’ Rev.01 Standard FCG Par 15.247 Test Distance 3m Test tem Harmonic Power nc sesy Frequency meonie Temp (C)Hum (%RHQ 28(C)ieo sR Mode: Mode 2 Ant.Polar Vertical 800 u/m Lini1 — Morgin: — 40 30000 1270 2200 3210 £10.00 $15.00 61200 70800 806 00 100000 Mtte No. Frequency. Reading Correct Factor Result Limi Margin Rematk hiz (aBuv) (dBim (dBuvim) (dBuvim) ta9) 1 234.6700 «121 «80 135 «5.00 «mss or 2 281.2300 s7.e3 «.63 33.00 «5.00 —13.00 or s «015100 sas2 222 37.80 «5.00 «270 or « «53.8000 «208 «o1 «115 «5.00 «.85 or s 730.3400 2787 «38 s225 «5.00 1375 or s s03.0700 207 7.70 ss67 «5.00 1233 or Note:1. Result(dBuVim) = Correct Factor (dB/m) + Reading(dBu\) Example: 34.3 =—6.08 +41.21 2Correction factor (dB/m) = Antenna Factor (dBfm) + Cable loss (d8) — Pre—Amplifier gain (dB) 3. When the peak resultsare less than average Iimit, so not need to evaluate the average 18 of 20

' ntl Report Number: 1905FR27 \’ Rev.01 Above 1 GHz Standard FCC Par 15.247 Test Distance 3m Test tem Harmonic Power nc sesv Frequency: sez uie Termp(C)/Hum (%RH) 26(C)ie0 wR Mode: Mode 2 Ant.Polar Horizontal $00 @u/m P 3 «n ao 1oon.oon scon cro.on ocso.on rizoninn taren on teson on toden on Praoni00 Zeson o0 ie No Frequency Reading Correct Factor Resut Limt Margin Rematk (viiz) (dBuv) (dBim) (dBuvim) (dBuvim (a8) 1 4922,000 a221 577 a7se 74.00 «26.02 peak 2 4922,000 30.20 577 as o7 5.00 «903 awe s 73ee.000 sa.15 1238 asas 74.00 «2782 peak a 73ee.000 2288 1238 s621 5.00 18.79 awe Note:1. Result(dBuVim) = Correct Factor (dB/m) + Reading(dBu\) Example: 47.08 = 5.77 +42.21 2Correction factor (dB/m) = Antenna Factor (dBfm) + Cable loss (d8) — Pre—Amplifier gain (dB) 3. When the peak resultsare less than average Iimit, so not need to evaluate the average 19 of 20

' ntl Report Number: 1905FR27 \’ Rev.01 Standard FCG Par 15.247 Test Distance 3m Test tem Harmonic Power nc sesy Frequency meonie Temp (C)Hum (%RHQ 28(C)ieo sR Mode: Mode 2 Ant.Polar Vertical 800 u/m t 3 a 40 1000 000. 360 00 s100 00 stso 00 1200 00— 12750.00 1€300.00 1g5000 2140000 26500 00 itc No. Frequency. Reading Correct Factor Result Limi Margin Rematk hiz (aBuv) (dBim (dBuvim) (dBuvim) ta9) 1 «922.000 «s1 5.77 s2ee 7400 BE peak 2 «922.000 «359 5.77 «038 s4.00 .66 awe s 73ee.000 .50 1233 «508 7400 2707 peak « 73ee.000 2277 1233 36.10 s4.00 —18.80 awe Note:1. Result(dBuVim) = Correct Factor (dB/m) + Reading(dBu\) Example: §2.68 = 5.77 + 46.91 2Correction factor (dB/m) = Antenna Factor (dBfm) + Cable loss (d8) — Pre—Amplifier gain (dB) 3. When the peak resultsare less than average Iimit, so not need to evaluate the average 20 of 20


Document Created: 2019-06-28 17:22:55
Document Modified: 2019-06-28 17:22:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC