Test Report

FCC ID: 2ADSQLH-69962

Test Report

Download: PDF
FCCID_3471472

RADIO TEST REPORT Report No: STS1705232F01 Issued for Lovehoney Ltd 100 Locksbrook Road, Bath, BA1 3EN, UK Love honey Desire Luxury USB Product Name: Rechargeable Rimming Butt Plug Brand Name: N/A Model Name: LH-69962 Series Model: N/A FCC ID: 2ADSQLH-69962 Test Standard: FCC Part 15.231 Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from BZT, All Test Data Presented in this report is only applicable to presented Test sample. BZT Testing Technology Co., Ltd Add. : Buliding 17, Xinghua Road Xingwei industrial Park Fuyong, Baoan District, Shenzhen, Guangdong, China TEL: +86-755 3307 1680 FAX: +86-755 27341758 E-mail:bruce@bzt.Cn

Page 2 of 31 Report No.: STS1705232F01 TEST REPORT CERTIFICATION Applicant’s name ........................ : Lovehoney Ltd Address ...................................... : 100 Locksbrook Road, Bath, BA1 3EN, UK Manufacture's Name ................... : Lovehoney Ltd Address ...................................... : 100 Locksbrook Road, Bath, BA1 3EN, UK Product description Love honey Desire Luxury USB Rechargeable Product name ............................. : Rimming Butt Plug Brand name ................................ : N/A Model and/or type reference ....... : LH-69962 Standards ................................... : FCC Part 15.231 Test procedure ............................ : ANSI C63.10-2013 This device described above has been tested by BZT , the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of BZT, this document may be altered or revised by BZT, personal only, and shall be noted in the revision of the document. Date of Test........................................... : Date of performance of tests ................ 27 May. : 2017 ~ 02 Jun. 2017 05 Jun. Date of Issue......................................... : 2017 Test Result ............................................ Pass : Testing Engineer : (Leo li) Technical Manager : (Tony liu) Authorized Signatory : (Vita Li)

Page 3 of 31 Report No.: STS1705232F01 TABLE OF CONTENTS 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF EUT 8 2.2 DESCRIPTION OF TEST MODES 9 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 9 2.4 DESCRIPTION OF SUPPORT UNITS 10 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 11 3. EMC EMISSION TEST 12 3.1 CONDUCTED EMISSION MEASUREMENT 12 3.2 TEST PROCEDURE 13 3.3 TEST SETUP 13 3.4 EUT OPERATING CONDITIONS 13 3.5 TEST RESULTS 14 4. RADIATED EMISSION MEASUREMENT 15 4.1 RADIATED EMISSION LIMITS 15 4.2 TEST PROCEDURE 16 4.3 DEVIATION FROM TEST STANDARD 16 5. BANDWIDTH TEST 23 5.1 APPLIED PROCEDURES / LIMIT 23 5.2 TEST REQUIREMENTS 23 5.3 TEST PROCEDURE 23 5.4 TEST SETUP 23 5.5 EUT OPERATION CONDITIONS 23 5.6 TEST RESULTS 24 6. DUTY CYCLE 25 6.1 TEST PROCEDURE 25 6.2 TEST SETUP 25 6.3 EUT OPERATION CONDITIONS 25 6.4 TEST RESULTS 26 7. AUTOMATICALLY DEACTIVATE 28 7.1 STANDARD REQUIREMENT 28 7.2 TEST PROCEDURE 28

Page 4 of 31 Report No.: STS1705232F01 TABLE OF CONTENTS 8. ANTENNA REQUIREMENT 30 8.1 STANDARD REQUIREMENT 30 8.2 EUT ANTENNA 30 APPENDIX 1- PHOTOS OF TEST SETUP 31

Page 5 of 31 Report No.: STS1705232F01 Revision History Rev. Issue Date Report NO. Effect Page Contents 00 05 Jun. 2017 STS1705232F01 ALL Initial Issue

Page 6 of 31 Report No.: STS1705232F01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part 15.231,Subpart C Standard Test Item Judgment Remark Section 15.207 Conducted Emission N/A -- 15.205(a)/15.209/ Radiated Spurious Emission PASS -- 15.231.(b) 15.231(a)(1)/ Transmission requirement PASS -- 15.231(b)(2) 15.231(C) 20 dB Bandwidth PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1)”N/A” denotes test is not applicable in this Test Report (2) All tests are according to ANSI C63.10-2013

Page 7 of 31 Report No.: STS1705232F01 1.1 TEST FACTORY BZT Testing Technology Co., Ltd. Buliding 17, Xinghua Road Xingwei industrial Park Fuyong, Baoan District, Shenzhen, Guangdong, China FCC Registration No.: 701733 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission (9KHz-150KHz) ±2.88dB 2 Conducted Emission (150KHz-30MHz) ±2.67dB 3 RF power,conducted ±0.70dB 4 Spurious emissions,conducted ±1.19dB 5 All emissions,radiated(<1G) 30MHz-200MHz ±2.83dB 6 All emissions,radiated(<1G) 200MHz-1000MHz ±2.94dB 8 Temperature ±0.5°C 9 Humidity ±2%

Page 8 of 31 Report No.: STS1705232F01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Love honey Desire Luxury USB Rechargeable Rimming Butt Equipment Plug Trade Name N/A Model Name LH-69962 Series Model N/A Model Difference N/A Frequency band 433.92MHz Power Rating DC 3.7 V TX: W0041TX V1.0 Hardware Hardware version number RX: W0041RX V1.0 Hardware TX: SDG335TX V02 FOR software Software version number RX: SDG335RX V03 FOR software Connecting I/O Port(s) N/A Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Table for filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) NOTE 1 N/A LH-69962 PCB N/A 0 Antenna The EUT antenna is PCB Antenna. No antenna other than that furnished by the responsible party shall be used with the device.

Page 9 of 31 Report No.: STS1705232F01 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX Mode For Radiated Emission Final Test Mode Description Mode 1 TX Mode 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED During test, Keep EUT is in continuous transmission mode, Both open button and closed button have been tested, The two keys were tested to assess and only record the worst case in the report(Open botton). E-1 EUT

Page 10 of 31 Report No.: STS1705232F01 2.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Serial No. Note Love honey Desire Luxury USB E-1 N/A LH-69962 N/A EUT Rechargeable Rimming Butt Plug Item Shielded Type Ferrite Core Length Note N/A N/A N/A N/A N/A Note: (1)For detachable type I/O cable should be specified the length in cm in『Length』column.

Page 11 of 31 Report No.: STS1705232F01 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until Spectrum Agilent E4407B MY50140340 2016.10.23 2017.10.22 Analyzer Test Receiver R&S ESCI 101427 2016.10.23 2017.10.22 Bilog Antenna TESEQ CBL6111D 34678 2014.11.24 2017.11.23 BBHA Horn Antenna Schwarzbeck 9120D(1201) 9120D-1343 2015.03.05 2018.03.04 1G-18G 50Ω Coaxial Anritsu MP59B 6200264416 2016.10.23 2017.10.22 Switch PreAmplifier Agilent 8449B 60538 2016.10.23 2017.10.22 Loop Antenna EMCO 6502 9003-2485 2016.03.06 2019.03.05 Spectrum Agilent E4407B MY50140340 2016.10.23 2017.10.22 Analyzer Low frequency cable SCHWARZBECK R01 N/A 2016.10.23 2017.10.22 (9KHz-1GHz) High frequency cable SCHWARZBECK R02 N/A 2016.10.23 2017.10.22 (1GHz-5GHz) Temporary Antenna N/A P9MSP9MS N/A 2016.10.23 2017.10.22 Connector MXHS83QE300 RF Cable Murrata 2085751 2016.10.23 2017.10.22 0 EMI Test Receiver R&S ESPI 102086 2016.10.23 2017.10.22 LISN R&S ENV216 101242 2016.10.23 2017.10.22 LISN EMCO 3810/2NM 000-23625 2016.10.23 2017.10.22 Conduction Cable EM C01 N/A 2016.10.23 2017.10.22 (150KHz-30MHz) Note: The temporary antenna connector is soldered on the PCB board in order to perform conducted tests and this temporary antenna connector is listed in the equipment list.

Page 12 of 31 Report No.: STS1705232F01 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS operating frequency band. In case the emission fall within the restricted band specified on Part 15. 207(a) limit in the table below has to be followed. Class B (dBuV) FREQUENCY (MHz) Standard Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * CISPR 0.50 -5.0 56.00 46.00 CISPR 5.0 -30.0 60.00 50.00 CISPR 0.15 -0.5 66 - 56 * 56 - 46 * FCC 0.50 -5.0 56.00 46.00 FCC 5.0 -30.0 60.00 50.00 FCC Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 13 of 31 Report No.: STS1705232F01 3.2 TEST PROCEDURE a.The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b.Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c.I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d.LISN at least 80 cm from nearest part of EUT chassis. e.For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.3 TEST SETUP Vertical Reference Ground Plane Test Receiver EUT 40cm 80cm LISN Horizontal Reference Ground Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 3.4 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

Page 14 of 31 Report No.: STS1705232F01 3.5 TEST RESULTS Temperature: 26 ℃ Relative Humidity: 54% Pressure: 1010hPa Phase : L/N Test Voltage: DC 3 V Test Mode: N/A Note: EUT is only power by battery, So it is not applicable for this test.

Page 15 of 31 Report No.: STS1705232F01 4. RADIATED EMISSION MEASUREMENT 4.1 RADIATED EMISSION LIMITS In case the emission fall within the restricted band specified on Part 15.205(a), then the Part 15.209(a)and Part 15.231(b) limit in the table below has to be followed. LIMITS OF RADIATED EMISSION MEASUREMENT (0.009MHz - 1000MHz) Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~40.66 100 3 40.70~70 100 3 Field Strength of Unwanted Fundamental Frequency Field Strength of fundamental Emissions (MHz) (microvolts/meter) (microvolts/meter) 40.66~40.70 225 2,250 70~130 125 1,250 130~174 1,250 to 3,750** 125 to 375** 174~260 3750 375 260~470 3,750 to 12,500** 375 to 1,250** Above 470 12,500 1,250 LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) Class B (dBuV/m) (at 3M) FREQUENCY (MHz) PEAK AVERAGE Above 1000 74 54 NOTE: (1)The limit for radiated test was performed according to FCC PART 15C. (2)Emission level (dBuV/m)=20log Emission level (uV/m).

Page 16 of 31 Report No.: STS1705232F01 Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RB / VB (emission in restricted band) 1 MHz / 3 MHz Setting Receiver Parameter Attenuation Auto Start ~ Stop Frequency 9kHz~90kHz / RB 200Hz for PK & AV Start ~ Stop Frequency 90kHz~110kHz / RB 200Hz for QP Start ~ Stop Frequency 110kHz~490kHz / RB 200Hz for PK & AV Start ~ Stop Frequency 490kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP 4.2 TEST PROCEDURE a. The test is performed in a 3m Semi-Anechoic Chamber; the antenna factor, cable loss and so on of the site (factors) is calculated to correct the reading. The EUT is placed on a 0.8m high insulating Turn Table, and keeps 3m away from the Test Antenna, which is mounted on a variable-height antenna master tower. During test, The table was rotated 360 degrees to determine the position of the highest radiation. b. In the frequency range of 9KHz to 30MHz, magnetic field is measured with Loop Test Antenna. The Test Antenna is positioned with its plane vertical at 1m distance from the EUT. The center of the Loop Test Antenna is 1m above the ground. During the measurement the Loop Test Antenna rotates about its vertical axis for maximum response at each azimuth about the EUT. c. In the frequency range 30MHz-1GHz, Bi-Log Test Antenna used. Test Antenna is 3m away from the EUT. Test Antenna height is varied from 1m to 4m above the ground to determine the maximum value of the field strength. The emission levels at both horizontal and vertical polarizations should be tested. d. In the frequency above 1GHz, Place the measurement antenna 3m away from the EUT for each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. f. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. g. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. h. For the actual test configuration, please refer to the related Item –EUT Test Photos. Both horizontal and vertical antenna polarities and performed pretest to three orthogonal axis were tested. The worst case emissions were reported 4.3 DEVIATION FROM TEST STANDARD No deviation

Caree 44 TEST SETUP (A) Radiated Emission Test—Up Frequency Below SOMHz ! W artenns Tocatable ia— In a \_{sur T | e LA «~" mm *—; 3. Spectrum nalrrct Recover (B) Radiated Emisston Test—Up Frequency SOMHz~1GHz Tontble Sema] \ Analyzer Ground Plane Connial Cable (C) Radiated Emission Test—Up Frequency Above 1GHz EUhk— 3m ——} Témable Im to im Spectrum Analyzer Ground Plan A Coaxial Cable 4.5 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows curing the testing.

Page 18 of 31 Report No.: STS1705232F01 4.6 TEST RESULTS INTRODUCTION TO PDCF reference: (§15.35 Measurement detector functions and bandwidths.) a. Part 15 of the FCC Rules provides for the operation of low power communication devices without an individual license (e.g., intrusion detectors, pulsed water tank level gauges, etc.), subject to certain requirements. Some of these devices use extremely narrow pulses to generate wideband emissions, which are measured to determine compliance with the rules. These measurements are typically performed with a receiver or spectrum analyzer. Depending on a number of factors (e.g., resolution bandwidth, pulsewidth, etc.), the spectrum analyzer may not always display the true peak value of the measured emission. This effect, called “pulse desensitization,” relates to the capabilities of the measuring instrument. For the measurement and reporting of the true peak of pulsed emissions, it may be necessary to apply a “pulse desensitization correction factor” (PDCF) to the measured value, pursuant to 47 CFR 15.35(a). If using spectrum analyzer to measure pulse signal , it have to make sure the RBW use is at least 2/PW. •When RBW is less than 2/PW , you are able to measure the true peak level of the pulse signal. If this is the case , PDCF is required to compensate to determine true peak value. Pulse desensitization: PW =24667usec,Period=55330usec, Level=A RBW>2/PW=0.081K , 1/T=0.018K NOTE: 2 / PW < RBW, first don't need b. For the actual test, please refer to the ANSI C63.10,Annex C refer to section 5 for more detail

Page 19 of 31 Report No.: STS1705232F01 4.7 TEST RESULTS (Radiated Emission<30MHz (9KHz-30MHz, H-field)) Freq. Reading Limit Margin State (MHz) (dBuV/m) (dBuV/m) (dB) P/F -- -- -- -- PASS -- -- -- -- PASS Note:The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Distance extrapolation factor =40 log (specific distance/test distance)(dB); Limit line = specific limits(dBuv) + distance extrapolation factor.

Page 20 of 31 Report No.: STS1705232F01 Between 30MHz — 5000 MHz Temperature: 26 °C Relative Humidity: (60% Pressure: 1010hPa Phase: Horizontal Test Voltage: DC 3 V Test Mode: Mode 1 no "sheo Tei reaw@® (Gocum uplum o| Peee 1 35.7490 37.58 —11.74 25.84 40.00 —14.16 aP 2 44.4308 40.78 —20.53 20.25 40.00 —19.75 aP 3 53.8817 41.17 —19.38 21.79 43.50 —21.71 aP 4 127.6645 42.46 —19.10 23.36 43.50 —20.14 aP 5 433.9200 7717 —10.90 66.27 100.83 —34.56 PK 6 867.8400 46.14 —2.61 43.53 80.83 —37.30 aP AV no "sue® Teaif rewr P Gécum amlum "a§° Peeeer 7 433.9200 66.27 —6.86 59.41 80.83 —21 42 AV Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBuV/m Limit1: — Margin: — 40.—,—, A __L_L_LLf——————41— 30.000 40 50 60 70 80 (MHz) 300 400 500 600 700 1000.000

Page 21 of 31 Report No.: STS1705232F01 Temperature: 26 °C Relative Humidity: 154% Pressure: 1010hPa Phase: Vertical Test Voltage: DC 3 V Test Mode: Mode 1 ne "ope® Te| ravc® goaum emlum o8| Peesr 1 35.7490 42.10 —14.86 27.24 40.00 —12.76 aP 2 44.4308 40.82 —20.36 20.46 40.00 —19.54 aP 3 53.8817 41.11 —17.61 23.50 43.50 —20.00 aP 4 127.6645 40.76 17.72 23.04 43.50 —20.46 aP 5 433.9200 68.73 —10.90 57.83 100.83 ~43.00 PK 6 867.8400 45.36 —2.61 42.75 80.83 —38.08 aP AV no tepe® "aim rer@® (Cooum amlum o8| Pte® 7 433.9200 57.83 —6.86 50.97 80.83 —29.86 AV Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: — —xet 40.—,—, |L___L__L_L_LLf—t—————1 1 3 a 0.0 30.000 40 50 60 70 80 (MHz] 300 400 500 600 700 1000.000

Page 22 of 31 Report No.: STS1705232F01 PEAK TEST RESULTS: RX Antenna Corrected Corrected Frequency Reading Detector Amplifier Loss Antenna Factor Factor Amplitude Limit Margin Polar (MHz) (dBμV/m) (PK/QP/AV) （dB） （dB） （dB/m） （dB） (dBμV/m) (dBμV/m) (dB) (H/V) 1301.76 59.68 PK 45.1 4.0 25.1 16.00 43.68 74 -30.32 H 1301.76 63.15 PK 45.1 4.0 25.1 16.00 47.15 74 -26.85 V 1735.68 61.46 PK 44.1 5.3 25 13.80 47.66 74 -26.34 H 1735.68 60.25 PK 44.1 5.3 25 13.80 46.45 74 -27.55 V 2169.6 61.23 PK 43.8 5.4 25.9 12.47 48.76 74 -25.24 H 2169.6 61.03 PK 43.8 5.4 25.9 12.47 48.56 74 -25.44 V 2603.3 61.02 PK 44.4 6.0 27.6 10.77 50.25 74 -23.75 H 2603.3 59.23 PK 44.4 6.0 27.6 10.77 48.46 74 -25.54 V Note: Above 2.6 GHz The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. AVG TEST RESULTS: AV = Peak +20Log10(duty cycle) =PK+(-6.30) [refer to section 5 for more detail] Corrected FCC Part 15.231/15.209/205 RX Antenna Frequency PK Reading Duty cycle Factor Amplitude Limit Margin Polar (MHz) (dBμV/m) (dB) (dBμV/m) (dBμV/m) (dB) (H/V) 1301.76 43.68 -6.51 37.17 54 -16.83 H 1301.76 47.15 -6.51 40.64 54 -13.36 V 1735.68 47.66 -6.51 41.15 54 -12.85 H 1735.68 46.45 -6.51 39.94 54 -14.06 V 2169.6 48.76 -6.51 42.25 54 -11.75 H 2169.6 48.56 -6.51 42.05 54 -11.95 V 2603.3 50.25 -6.51 43.74 54 -10.26 H 2603.3 48.46 -6.51 41.95 54 -12.05 V

Page 23 of 31 Report No.: STS1705232F01 5. BANDWIDTH TEST 5.1 APPLIED PROCEDURES / LIMIT FCC Part 15.231,Subpart C Frequency Range Section Test Item Limit Result (MHz) The 20dB bandwidth of the emissions shall not exceed 15.231(C) 20 Bandwidth 433.92 PASS 0.25% of the center frequency Spectrum Parameter Setting Attenuation Auto Span Frequency > Measurement Bandwidth RB 10 kHz (20dB Bandwidth) VB 30 kHz (20dB Bandwidth) Detector Peak Trace Max Hold Sweep Time Auto 5.2 TEST REQUIREMENTS The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. 5.3 TEST PROCEDURE a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram below. b. Spectrum Setting : RBW= 10KHz, VBW=30KHz, Sweep time = Auto. 5.4 TEST SETUP 5.5 EUT OPERATION CONDITIONS TX mode.

Page 24 of 31 Report No.: STS1705232F01 5.6 TEST RESULTS Measurement Centre Frequency 20dB Bandwidth Limit(kHz) Frequency Range (MHz) (KHz) 433.92 MHz 57 1084.8 PASS CH00 -1Mbps

Page 25 of 31 Report No.: STS1705232F01 6. DUTY CYCLE 6.1 TEST PROCEDURE The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram below. The Duty Cycle Was Determined By The Following Equation: To Calculate The Actual Field Intensity,The Duty Cycle Correction Factor In Decibel Is Needed For Later Use And Can Be Obtained From Following Conversion Duty Cycle(%)=Total On Interval In A Complete Pulse Train/ Length Of A Complete Pulse Train * % Duty Cycle Correction Factor(Db)=20 * Log10(Duty Cycle(%) 6.2 TEST SETUP 6.3 EUT OPERATION CONDITIONS TX mode.

Page 26 of 31 Report No.: STS1705232F01 6.4 TEST RESULTS FCC Part 15.231(a) Total On interval in a complete pulse train(ms) (5.167*1)+(1.5*13)=24.667 Length of a complete pulse train(ms) 54.33 Duty Cycle(%) 45.40% Duty Cycle Correction Factor(dB) -6.86 Refer to the duty cycle plot (as below),This device meets the FCC requirement. Length of a complete pulse train Remark:FCC part15.35(c) required that a complete pulse train is more than 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum value. TX Mode

Page 27 of 31 Report No.: STS1705232F01

age 28 of 31 Loob enc 7. AUTOMATICALLY DEACTIVATE 7.1 STANDARD REQUIREMENT A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released 7.2 TEST PROCEDURE The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram below. Spactrum Setting : RBW= 100KHz, VBW=300KHz, Sweep time = Auto Nate: Only press launch about 0.15 s Note: {1)Refer to the plot (As Below), We find a manually operated transmitter shall employ a switch that will automatically deactivate the transmitteri immediately, within not more than 5 secands of being released (Z)The EUT is comply with FCC PART 15 clause 15.231(a)(1). manually working mode are pre—tested.and only the worst result is reported 7.3 TEST SETUP EUT SPECTRUM ANALYZER 7.4 TEST RESULTS Activation time Limit(Sec) Result 5s 5s Pass

Page 29 of 31 Report No.: STS1705232F01 Mark 1: Hold down the Key(Start transmitting) Mark 3: Loose the Key Mark 2: Stop transmitting Activation time= Mark 2- Mark 1=2.217-1.467=0.75s

Page 30 of 31 Report No.: STS1705232F01 8. ANTENNA REQUIREMENT 8.1 STANDARD REQUIREMENT According to the FCC Part 15 Paragraph 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna to the intentional radiator shall be considered sufficient to comply with the provisions of this section. 8.2 EUT ANTENNA The EUT antenna is Internal PCB Antenna.It conforms to the standard requirements.

Page 31 of 31 Report No.: STS1705232F01 APPENDIX 1- PHOTOS OF TEST SETUP Radiated Measurement Photos ※※※※※END OF THE REPORT※※※※※


Document Created: 2017-07-12 01:30:54
Document Modified: 2017-07-12 01:30:54
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC