DFS Test Report

FCC ID: 2ABZ2-A3000

Test Report

Download: PDF
FCCID_3007273

FCC PART 15 TEST REPORT No. I16Z40476-SRD015 for OnePlus Technology(Shenzhen) Co., Ltd. Mobile Phone Model Name: ONEPLUS A3000 FCC ID: 2ABZ2-A3000 with Hardware Version: 16 Software Version: Qxygen OS 3.1.0 Issued Date: 2016-05-26 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL. Test Laboratory: CTTL, Telecommunication Technology Labs, Academy of Telecommunication Research, MIIT No.52, HuayuanNorth Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512,Fax:+86(0)10-62304633-2504 Email:cttl_terminals@catr.cn, website:www.chinattl.com

No. I16Z40476-SRD015 Page2 of 18 REPORT HISTORY Report Number Revision Description Issue Date I16Z40476-SRD015 Rev.0 1st edition 2016-05-17 I16Z40476-SRD015 Rev.1 2ed edition 2016-05-23 I16Z40476-SRD015 Rev.2 3rd edition 2016-05-26

No. I16Z40476-SRD015 Page3 of 18 CONTENTS CONTENTS .......................................................................................................................................3 1. TEST LATORATORY .........................................................................................................4 1.1. TESTING LOCATION ........................................................................................................4 1.2. TESTING ENVIRONMENT ...............................................................................................4 1.3. PROJECT DATA.................................................................................................................4 1.4. SIGNATURE .......................................................................................................................4 2. CLIENT INFORMATION ...................................................................................................5 2.1. APPLICANT INFORMATION............................................................................................5 2.2. MANUFACTURER INFORMATION..................................................................................5 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT(AE) .....................6 3.1. ABOUT EUT .......................................................................................................................6 3.2. INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST...............................6 3.3. GENERAL DESCRIPTION.................................................................................................6 4. REFERENCE DOCUMENTS..............................................................................................7 4.1. DOCUMENTS SUPPLIED BY APPLICANT ......................................................................7 4.2. REFERENCE DOCUMENTS FOR TESTING....................................................................7 5. LABORATORY ENVIRONMENT ......................................................................................7 6. SUMMARY OF TEST RESULTS ........................................................................................7 6.1. SUMMARY OF TEST RESULTS ........................................................................................7 6.2. STATEMENTS ....................................................................................................................7 7. TEST EQUIPMENTS UTILIZED .......................................................................................8 ANNEX A: MEASUREMENT RESULTS ..........................................................................................9 A.1. MEASUREM ENT METHOD ...........................................................................................................9 A.2. CHANNEL MOVE TIM E AND CHANNEL CLOSING TRANSM ISSION TIM E............................................. 11 A.3. NON-OCCUPANCY P ERIOD ........................................................................................................16 A3.1 ASSOCIATED TEST ...................................................................................................................16 ANNEX B: PHOTOGRAPHS OF THE TEST SET-UP ....................................................................17 ANNEX C: ACCREDITATION CERTIFICATE ..............................................................................18

No. I16Z40476-SRD015 Page4 of 18 1. TEST LATORATORY 1.1. Testing Location Location 1:CTTL(huayuan North Road) Address: No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China100191 Location 2:CTTL(Shouxiang) Address: No. 51 Shouxiang Science Building, Xueyuan Road, Haidian District, Beijing, P. R. China100191 1.2. Testing Environment Normal Temperature: 15-35℃ Extreme Temperature: 0/+35℃ Relative Humidity: 20-75% 1.3. Project data Testing Start Date: 2016-04-06 Testing End Date: 2016-05-16 1.4. Signature Jiang Xue (Approved this test report) Zheng Wei (Reviewed this test report) Lv Songdong (Approved this test report)

No. I16Z40476-SRD015 Page5 of 18 2. CLIENT INFORMATION 2.1. Applicant Information Company Name: OnePlus Technology(Shenzhen) Co., Ltd. Address /Post: 18/F, Tower C, Tai Ran Building,No.8 Tai Ran Road, Shenzhen, China Contact Kevin Ke Email keyoujiang@oneplus.cn Telephone: 0755 61898696 EXT 7023 Fax: / 2.2. Manufacturer Information Company Name: OnePlus Technology(Shenzhen) Co., Ltd. Address /Post: 18/F, Tower C, Tai Ran Building,No.8 Tai Ran Road, Shenzhen, China Contact Kevin Ke Email keyoujiang@oneplus.cn Telephone: 0755 61898696 EXT 7023 Fax: /

No. I16Z40476-SRD015 Page6 of 18 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT(AE) 3.1. About EUT Description Mobile Phone Model name ONEPLUS A3000 FCC ID 2ABZ2-A3000 WLAN Frequency Range ISM Band: -5250MHz~5350MHz -5470MHz~5725MHz Type of modulation OFDM Antenna Integral Antenna Extreme vol. Limits 3.8V DC by Battery Device Type (DFS) Client without radar detection(only support client mode) TPC mechanism Not support 3.2. Internal Identification of EUT used during the test EUT ID* S/N HW Version SW Version EUT1 860046030181863 16 Qxygen OS 3.1.0 *EUT ID: is used to identify the test sample in the lab internally. 3.3. General Description The Equipment Under Test (EUT) is a model of Mobile Phone with integrated antenna. It consists of normal options: lithium battery, charger. Manual and specifications of the EUT were provided to fulfil the test.

No. I16Z40476-SRD015 Page7 of 18 4. REFERENCE DOCUMENTS 4.1. Documents supplied by applicant EUT feature information is supplied by the applicant or manufacturer, which is the basis of testing. 4.2. Reference Documents for testing The following documents listed in this section are referred for testing. Title 47 of the Code of Federal Regulations; Chapter I 2015 FCC Part15 Part 15 - Radio frequency devices Subpart E – UNII Devices Revision of Parts 2 and 15 of the Commission’s Rules to FCC 06-96 Permit Unlicensed National Information Infrastructure 2006 (U-NII) devices in the 5 GHz band U-NII CLIENT DEVICES WITHOUT RADAR DETECTION KDB 905462 D03 2014 CAPABILITY 5. LABORATORY ENVIRONMENT Measurement is performed in shielding room. 6. SUMMARY OF TEST RESULTS 6.1. Summary of Test Results Sub-clause of SUMMARY OF MEASUREMENT RESULTS Verdict Part15C Channel move time and channel closing 4.7.2 P transmission time Non-Occupancy Period 4.7.2 P Please refer to ANNEX A for detail. Terms used in Verdict column P Pass, The EUT complies with the essential requirements in the standard. NM Not measured, The test was not measured by CTTL NA Not Applicable, The test was not applicable F Fail, The EUT does not comply with the essential requirements in the standard 6.2. Statements CTTL has evaluated the test cases requested by the client/manufacturer as listed in section 6.1 of this report for the EUT specified in section 3 according to the standards or reference documents listed in section 4.1. This report only deal with the UNII DFS functions among the features described in section 3, and The EUT met all requirements of the reference documents. The end user is not available to get and modify the parameters of the detected Radar Waveforms in this product.

No. I16Z40476-SRD015 Page8 of 18 Test Conditions T nom Normal Temperature T min Low Temperature T max High Temperature V nom Normal Voltage V min Low Voltage V max High Voltage H nom Norm Humidity A nom Norm Air Pressure For this report, all the test case listed above is tested under Normal Temperature and Normal Voltage, and also under norm humidity, the specific conditions as following: Temperature T nom 26℃ Voltage V nom 3.8V(By battery) Humidity H nom 44% Air Pressure A nom 1010hPa 7. TEST EQUIPMENTS UTILIZED Conducted test system Serial Calibration Calibration No. Equipment Model Manufacturer Number Date Due Date Vector Signal Rohde & 1 FSQ40 200089 2015-07-01 2016-06-30 Analyzer Schwarz Vector Signal Rohde & 2 SMU200A 103752 2015-07-01 2016-06-30 General Schwarz 3 Shielding Room S81 / ETS-Lindgren / /

No. I16Z40476-SRD015 Page9 of 18 ANNEX A: MEASUREMENT RESULTS A.1. Measurement Method A.1.1. Conducted Measurements The below figure shows the DFS setup, where the EUT is a RLAN device operating in slave mode, without Radar Interference Detection function. This setup also contains a device operating in master mode. The radar test signals are injected into the master device. The EUT (slave device) is associated with the master device. WLAN traffic is generated by streaming the mpeg file from the master to the slave in full monitor video mode using the media player. Note: 1) All Measurements are performed with the EUT’s narrowest channel bandwidth. 2) The master device information is as follows Vendor: Cisco Model: AIR-AP1252AG-A-K9 FCC ID: LDK102061, 1DK102062 3) The software of radar signal generator (R&S SMU200A) is completely designed based on FCC-06-96A1/NTIA requirement. A.1.2. Parameters of DFS test signal 1). Interference threshold values, master or client incorporation in service monitoring. For device power less than 23dBm (E.I.R.P.), the threshold level is -62 dBm at the antenna port after correction for antenna gain and procedural adjustments. Because of conducted measurement performed, the calibration power from radar signal generator to antenna port of DFS test equipment is -62 dBm. Maximum Transmit Power Value > 200 mW -64 dBm < 200 mW -62 dBm

No. I16Z40476-SRD015 Page10 of 18 2). DFS requirement values The required values are as the following table. Parameter Value Non-occupancy > 1800 s Channel Availability Check Time 60 s Channel Move Time 10 s Channel Closing Transmission Time 200 ms + 60 ms Minimum 80% of the 99% U-NII Detection Bandwidth transmission power bandwidth As the EUT is IP based system, the MPEG video file from NTIA website is used to steam to EUT via the Master device. A.1.3. Measurement Uncertainty Item Measurement Uncertainty Time 0.70 ms Power 0.75 dBm

No. I16Z40476-SRD015 Page11 of 18 A.2. Channel move time and channel closing transmission time Measurement Limit: Test Items Limit channel closing transmission time < 200 ms + 60 ms Channel move time < 10 s Measurement Results: HT20 Frequency Band: 5250MHz ~ 5350MHz RBW 3 MHz Delta 3 [T1 ] VBW 10 MHz -53.33 dB Ref 10 dBm * Att 20 dB SWT 12 s 10.000000 s 10 Marker 1 [T1 ] 1 3.19 dBm 961.538462 ms A 0 Delta 2 [T1 ] SGL 1 AP -53.24 dB CLRWR -10 115.384615 ms -20 -30 -40 2 3 3DB -50 -60 -70 -80 -90 Center 5.26 GHz 1.2 s/ Date: 9.MAY.2016 15:54:27 The channel move time is as the figure. It shows the time of the radar and the client pulses. The figure shows that the client stops transmission within 10 seconds, and no transmissions occur after 10 seconds later of the radar burst signal.

No. I16Z40476-SRD015 Page12 of 18 RBW 3 MHz Delta 2 [T1 ] VBW 10 MHz -52.46 dB Ref 10 dBm * Att 20 dB SWT 600 ms 10.576923 ms 10 Marker 1 [T1 ] 1 2.83 dBm 297.115385 ms A 0 SGL 1 AP CLRWR -10 -20 -30 -40 2 3DB -50 -60 -70 -80 -90 Center 5.28 GHz 60 ms/ Date: 9.MAY.2016 15:57:34 The closing transmission time is as the figure, and the result is 10.58ms. Conclusion: PASS HT80 Frequency Band: 5250MHz ~ 5350MHz RBW 3 MHz Delta 3 [T1 ] VBW 10 MHz -36.44 dB Ref 0 dBm * Att 20 dB SWT 12 s 10.000000 s 0 Marker 1 [T1 ] -19.83 dBm 596.153846 ms A -10 Delta 2 [T1 ] SGL 1 AP -36.58 dB 1 CLRWR -20 19.230769 ms -30 -40 -50 2 3 3DB -60 -70 -80 -90 -100 Center 5.29 GHz 1.2 s/ Date: 9.MAY.2016 16:45:43 The channel move time is as the figure. It shows the time of the radar and the client pulses. The figure shows that the client stops transmission within 10 seconds, and no transmissions occur after 10 seconds later of the radar burst signal.

No. I16Z40476-SRD015 Page13 of 18 RBW 3 MHz Delta 2 [T1 ] VBW 10 MHz -36.61 dB Ref 0 dBm * Att 20 dB SWT 600 ms 66.346154 ms 0 Marker 1 [T1 ] -19.80 dBm 301.923077 ms A -10 SGL 1 AP 1 CLRWR -20 -30 -40 -50 2 3DB -60 -70 -80 -90 -100 Center 5.31 GHz 60 ms/ Date: 9.MAY.2016 16:48:48 The closing transmission time is as the figure, and the result is 66.35ms Conclusion: PASS HT20 Frequency Band 5470MHz ~ 5725MHz RBW 3 MHz Delta 3 [T1 ] VBW 10 MHz -52.84 dB Ref 10 dBm * Att 20 dB SWT 12 s 10.000000 s 10 Marker 1 [T1 ] 1 2.61 dBm 942.307692 ms A 0 Delta 2 [T1 ] SGL 1 AP -52.43 dB CLRWR -10 38.461538 ms -20 -30 -40 2 3 3DB -50 -60 -70 -80 -90 Center 5.68 GHz 1.2 s/ Date: 17.MAY.2016 16:12:15 The channel move time is as the figure. It shows the time of the radar and the client pulses. The figure shows that the client stops transmission within 10 seconds, and no transmissions occur after 10 seconds later of the radar burst signal.

No. I16Z40476-SRD015 Page14 of 18 RBW 3 MHz Delta 2 [T1 ] VBW 10 MHz -54.59 dB Ref 20 dBm * Att 20 dB SWT 600 ms 29.807692 ms 20 Marker 1 [T1 ] 3.86 dBm 342.307692 ms A 10 1 SGL 1 AP CLRWR 0 -10 -20 -30 3DB -40 2 -50 -60 -70 -80 Center 5.5 GHz 60 ms/ Date: 10.MAY.2016 16:17:00 The closing transmission time is as the figure, and the result is 29.81ms Conclusion: PASS HT80 Frequency Band 5470MHz ~ 5725MHz RBW 3 MHz Delta 3 [T1 ] VBW 10 MHz -31.78 dB Ref 0 dBm Att 25 dB SWT 12 s 10.000000 s 0 Marker 1 [T1 ] -19.76 dBm 730.769231 ms A -10 Delta 2 [T1 ] SGL 1 AP -31.13 dB 1 CLRWR -20 96.153846 ms -30 -40 2 3 -50 3DB -60 -70 -80 -90 -100 Center 5.53 GHz 1.2 s/ Date: 12.MAY.2016 19:35:20 The channel move time is as the figure. It shows the time of the radar and the client pulses. The figure shows that the client stops transmission within 10 seconds, and no transmissions occur after 10 seconds later of the radar burst signal.

No. I16Z40476-SRD015 Page15 of 18 RBW 3 MHz Delta 2 [T1 ] VBW 10 MHz -36.80 dB Ref 0 dBm * Att 20 dB SWT 600 ms 58.653846 ms 0 Marker 1 [T1 ] -20.04 dBm 398.076923 ms A -10 SGL 1 AP 1 CLRWR -20 -30 -40 -50 2 3DB -60 -70 -80 -90 -100 Center 5.53 GHz 60 ms/ Date: 16.MAY.2016 11:53:35 The closing transmission time is as the figure, and the result is 58.65ms Conclusion: PASS

No. I16Z40476-SRD015 Page16 of 18 A.3. Non-Occupancy Period Measurement Limit: Test Items Limit Non-Occupancy Period > 1800 s A3.1 Associated test Associate the master and client, transmit specified stream between the master and client; monitor the analyzer on the operating frequency to make sure no beacons have been transmitted for 1800 seconds. RBW 3 MHz Delta 3 [T1 ] * VBW 10 MHz -55.94 dB Ref 10 dBm * Att 10 dB SWT 2000 s 1.800000 ks 10 Marker 1 [T1 ] 1 3.09 dBm 35.256410 s A 0 Delta 2 [T1 ] SGL 1 AP -56.66 dB CLRWR -10 3.205128 s -20 -30 -40 3DB -50 2 3 -60 -70 -80 -90 Center 5.58 GHz 200 s/ Date: 26.MAY.2016 16:12:52 The figure above shows that the client does not transmit any emission within 1800 seconds after getting the order of “stop transmits” from the DFS master (access point). Conclusion: PASS

No. I16Z40476-SRD015 Page17 of 18 ANNEX B: PHOTOGRAPHS OF THE TEST SET -UP Layout of Conducted Test

No. I16Z40476-SRD015 Page18 of 18 ANNEX C: Accreditation Certificate *** END OF REPORT BODY ***


Document Created: 2017-12-06 18:08:17
Document Modified: 2017-12-06 18:08:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC