Test Report_15.225

FCC ID: 2ABTU-PM-521

Test Report

Download: PDF
FCCID_2547136

Report No. 1510151R-RFUSP17V00 FCC Test Report Product Name TABLET PC Model No. PM-521 FCC ID 2ABTU-PM-521 Applicant RuggON Corporation Address 3F., No.10, Ln. 181, Sec. 2, Jiuzong Rd., Neihu Dist., Taipei City, Taiwan Date of Receipt Jan. 06, 2015 Issued Date Feb. 16, 2015 Report No. 1510151R-RFUSP17V00 Report Version V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration report of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of QuieTek Corporation. Page: 1 of 27

Report No. 1510151R-RFUSP17V00 Tes t R e p o r t Issued Date: Feb. 16, 2015 Report No.: 1510151R-RFUSP17V00 Product Name TABLET PC Applicant RuggON Corporation Address 3F., No.10, Ln. 181, Sec. 2, Jiuzong Rd., Neihu Dist., Taipei City, Taiwan Manufacturer Ubiqconn Technology,Inc. Model No. PM-521 FCC ID. 2ABTU-PM-521 EUT Rated Voltage AC 100-240V, 50-60Hz EUT Test Voltage AC 120V/60Hz Trade Name RuggON Applicable Standard FCC CFR Title 47 Part 15 Subpart C: 2014 ANSI C63.4: 2014, ANSI C63.10: 2013 Test Result Complied Documented By : ( Senior Adm. Specialist / Joanne Lin ) Tested By : ( Engineer / Alan Chen ) Approved By : ( Director / Vincent Lin ) Page: 2 of 27

Report No. 1510151R-RFUSP17V00 TA B L E O F C O N T E N T S Description Page 1. GENERAL INFORMATION .....................................................................................................4 1.1. EUT Description............................................................................................................................4 1.2. Operational Description ................................................................................................................5 1.3. Tested System Datails....................................................................................................................6 1.4. Configuration of tested System .....................................................................................................6 1.5. EUT Exercise Software .................................................................................................................7 1.6. Test Facility ...................................................................................................................................7 2. Conducted Emission....................................................................................................................9 2.1. Test Equipment..............................................................................................................................9 2.2. Test Setup ......................................................................................................................................9 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................10 2.5. Uncertainty ..................................................................................................................................10 2.6. Test Result of Conducted Emission.............................................................................................11 3. Radiated Emission.....................................................................................................................13 3.1. Test Equipment............................................................................................................................13 3.2. Test Setup ....................................................................................................................................13 3.3. Limits ..........................................................................................................................................14 3.4. Test Procedure .............................................................................................................................15 3.5. Uncertainty ..................................................................................................................................16 3.6. Test Result of Radiated Emission................................................................................................17 4. Band Edge ..................................................................................................................................20 4.1. Test Equipment............................................................................................................................20 4.2. Test Setup ....................................................................................................................................20 4.3. Limits ..........................................................................................................................................21 4.4. Test Procedure .............................................................................................................................21 4.5. Uncertainty ..................................................................................................................................21 4.6. Test Result of Band Edge ............................................................................................................22 5. Frequency Tolerance .................................................................................................................23 5.1. Test Equipment............................................................................................................................23 5.2. Test Setup ....................................................................................................................................23 5.3. Limits ..........................................................................................................................................23 5.4. Test Procedure .............................................................................................................................23 5.5. Uncertainty ..................................................................................................................................23 5.6. Test Result of Frequency Stability...............................................................................................24 6. EMI Reduction Method During Compliance Testing ............................................................26 Attachment 1: EUT Test Photographs Attachment 2: EUT Detailed Photographs Page: 3 of 27

Report No. 1510151R-RFUSP17V00 1. GENERAL INFORMATION 1.1. EUT Description Product Name TABLET PC Trade Name RuggON Model No. PM-521 FCC ID 2ABTU-PM-521 Frequency Range 13.56MHz Modulation ASK Antenna Type Loop antenna Power Adapter MFR: FSP, M/N: FSP065-REB Input: AC 100-240V~1.5A, 50-60Hz Output: 19V 3.42A Cable Out: Shielded, 1.5m, with one ferrite core bonded. Contain Module Intel / 7260HMW Frequency of Each Channel: Channel Frequency Channel 1: 13.56 MHz Note: 1. This device is a TABLET PC with a built-in 13.56MHz transceiver. 2. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15 Subpart C Paragraph 15.225 3. The radiation measurements are performed in X, Y, Z axis positioning. Only the worst case is shown in the report. Test Mode Mode 1: Transmit mode Page: 4 of 27

Report No. 1510151R-RFUSP17V00 1.3. Tested System Datails The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord 1 Monitor DELL ST2320L N/A Non-Shielded, 1.8m 2 Earphone AIWA N/A N/A N/A 3 IPod nano Apple A1199 YM708A72VQ5 N/A 4 Modem ACEEX DM-1414 0102027553 N/A 5 USB Dongle Transcend JF V30 N/A Non-Shielded, 1.8m Signal Cable Type Signal cable Description A HDMI Cable Shielded, 1.8m B Earphone Cable Shielded, 1.8m C IPod Cable Shielded, 1.2m D RS-232 Cable Shielded, 1.8m E RJ45 Cable Shielded, 2.0m 1.4. Configuration of tested System Page: 6 of 28

Report No. 1510151R-RFUSP17V00 1.5. EUT Exercise Software (1) Setup the EUT as shown in Section 1.4 (2) Execute software “DRTU-v1.7.3.859” on the Notebook PC. (3) Configure the test mode, the test channel, and the data rate. (4) Press “OK” to start the continuous Transmit. (5) Verify that the EUT works properly. Page: 7 of 28

Report No. 1510151R-RFUSP17V00 1.6. Test Facility Ambient conditions in the laboratory: Items Required (IEC 68-1) Actual Temperature (C) 15-35 20-35 Humidity (%RH) 25-75 50-65 Barometric pressure (mbar) 860-1060 950-1000 The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site: http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site: http://www.quietek.com/ Site Description: File on Federal Communications Commission FCC Engineering Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Registration Number: 92195 Site Name: Quietek Corporation Site Address: No.5-22, Ruishukeng, Linkou Dist. New Taipei City 24451, Taiwan, R.O.C. TEL: 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : service@quietek.com FCC Accreditation Number: TW1014 Page: 8 of 28

Report No. 1510151R-RFUSP17V00 2. Conducted Emission 2.1. Test Equipment Equipment Manufacturer Model No. / Serial No. Last Cal. Remark X Test Receiver R&S ESCS 30 / 825442/018 Sep., 2014 X Artificial Mains Network R&S ENV4200 / 848411/10 Feb., 2015 Peripherals X LISN R&S ESH3-Z5 / 825562/002 Feb., 2015 EUT DC LISN Schwarzbeck 8226 / 176 Mar., 2014 EUT X Pulse Limiter R&S ESH3-Z2 / 357.8810.52 Feb., 2015 No.1 Shielded Room Note: 1. All equipments are calibrated every one year. 2. The test instruments marked by “X” are used to measure the final test results. 2.2. Test Setup Reference Plane Test Receiver 40cm 12dBuV Load EUT   LISN LISN LISN Ground Plane Page: 9 of 28

Report No. 1510151R-RFUSP17V00 2.3. Limits FCC Part 15 Subpart C Paragraph 15.207 (dBμV) Limit Frequency Limits MHz QP AV 0.15 - 0.50 66-56(註) 56-46(註) 0.50-5.0 56 46 5.0 - 30 60 50 2.4. Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm /50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10: 2013 on conducted measurement. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz. 2.5. Uncertainty ± 2.26 dB Page: 10 of 28

Report No. 1510151R-RFUSP17V00 2.6. Test Result of Conducted Emission Product : TABLET PC Test Item : Conducted Emission Test Power Line : Line 1 Test Mode : Mode 1: Transmit mode Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz dB dBμV dBμV dB dBμV LINE 1 Quasi-Peak 0.170 9.743 34.220 43.964 -21.465 65.429 0.216 9.739 30.030 39.769 -24.345 64.114 0.334 9.745 27.380 37.125 -23.618 60.743 0.490 9.752 32.180 41.932 -14.354 56.286 0.779 9.765 28.600 38.365 -17.635 56.000 7.920 9.910 27.320 37.230 -22.770 60.000 Average 0.170 9.743 18.800 28.544 -26.885 55.429 0.216 9.739 22.700 32.439 -21.675 54.114 0.334 9.745 24.340 34.085 -16.658 50.743 0.490 9.752 24.580 34.332 -11.954 46.286 0.779 9.765 20.320 30.085 -15.915 46.000 7.920 9.910 21.530 31.440 -18.560 50.000 Note: 1. All Reading Levels are Quasi-Peak and average value. 2. “ “ means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 11 of 28

Report No. 1510151R-RFUSP17V00 Product : TABLET PC Test Item : Conducted Emission Test Power Line : Line 2 Test Mode : Mode 1: Transmit mode Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz dB dBμV dBμV dB dBμV LINE 2 Quasi-Peak 0.173 9.747 31.650 41.397 -23.946 65.343 0.509 9.753 33.100 42.853 -13.147 56.000 0.771 9.775 28.660 38.435 -17.565 56.000 1.974 9.839 19.840 29.679 -26.321 56.000 6.685 9.900 23.990 33.890 -26.110 60.000 20.920 10.100 24.460 34.560 -25.440 60.000 Average 0.173 9.747 12.100 21.847 -33.496 55.343 0.509 9.753 21.120 30.873 -15.127 46.000 0.771 9.775 18.660 28.435 -17.565 46.000 1.974 9.839 6.030 15.869 -30.131 46.000 6.685 9.900 16.290 26.190 -23.810 50.000 20.920 10.100 19.050 29.150 -20.850 50.000 Note: 1. All Reading Levels are Quasi-Peak and average value. 2. “ “ means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 12 of 28

Report No. 1510151R-RFUSP17V00 3. Radiated Emission 3.1. Test Equipment The following test equipments are used during the radiated emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 3 X Magnetic Loop Teseq HLA6121/ 37133 Sep., 2014 Antenna X Bilog Antenna Schaffner Chase CBL6112B/ 2707 Jun., 2014 X EMI Test Receiver R&S ESCS 30/838251/ 001 Jun., 2014 X Coaxial Cable QTK(Arnist) RG 214/ LC003-RG Jun., 2014 X Coaxial signal switch Arnist MP59B/ 6200798682 Jun., 2014 3.2. Test Setup 9kHz~30MHz 3m FRP Dome Antenna Mast EUT Broadband or Loop Non-Conducted Table Antenna 1m 80cm Fully soldered Metal Ground Test To Receiver Receiver Page: 13 of 28

Report No. 1510151R-RFUSP17V00 30MHz~1GHz 3m FRP Dome 1m to 4m The height of board band or Dipole Antenna was scanned from 1M to 4M. The distance between antenna and turn table was 3M regards to the EUT standard adopted. Non-Conducted Table 80cm Fully soldered Metal Ground To Controller Test To Receiver Receiver 3.3. Limits  Fundamental electric field strength Limit FCC Part 15 Subpart C Paragraph 15.225 Limits Field strength of fundamental Fundamental Frequency MHz Distance Distance uV/m dBμV/m (meter) (meter) 13.553 – 13.567 15848 30 124 3 13.410 – 13.553 and 13.567 – 13.710 334 30 90.47 3 13.110 – 13.410 and 13.710 – 14.010 106 30 80.50 3 Outside of the 13.110 – 14.010 See 15.209 Limits Remarks : 1. RF Voltage (dBμV) = 20 log RF Voltage (uV) 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 3. The emission limit in this paragraph is based on measurement instrumentation employing an average detector. Page: 14 of 28

Report No. 1510151R-RFUSP17V00  Spurious electric field strength Limit FCC Part 15 Subpart C Paragraph 15.209 Limits Frequency Measurement distance uV/m dBμV/m MHz (meter) 0.009-0.490 2400/F(kHz) See Remark1 300 0.490-1.705 24000/F(kHz) See Remark1 30 1.705-30 30 29.5 30 30-88 100 40 3 88-216 150 43.5 3 216-960 200 46 3 Above 960 500 54 3 Remarks : 1. RF Voltage (dBμV) = 20 log RF Voltage (uV) 2. In the Above Table, the tighter limit applies at the band edges. 3. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 3.4. Test Procedure Fundamental electric field strength: The EUT and its simulators are placed on a turn table which is 1 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum electric field strength. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna which is 1 meter above ground. All X-axis, Y-axis and Z-axis polarization of the antenna are set on measurement. Spurious electric field strength: The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ANSI C63.10: 2013 on radiated measurement. On any frequency the radiated limits shown are based upon the use of measurement instrumentation employing an average detector function. When average radiated emission measurement are included emission measurement below 1000 MHz, there also is a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit. The bandwidth below 30MHz setting on the field strength meter is 9kHz and above 30MHz is 120kHz. The frequency range from 9kHz to 10th harmonics is checked. Page: 15 of 28

Report No. 1510151R-RFUSP17V00 3.5. Uncertainty ± 2.6 dB below 30MHz ± 3.8 dB above 30MHz Page: 16 of 28

Report No. 1510151R-RFUSP17V00 3.6. Test Result of Radiated Emission Product : TABLET PC Test Item : Fundamental Radiated Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmit mode Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz dB dBμV dBμV/m dB dBμV/m X-axis Quasi-Peak Horizontal 13.560 20.410 37.150 57.560 -66.440 124.000 Vertical 13.560 20.410 39.630 60.040 -63.960 124.000 Y-axis Quasi-Peak Horizontal 13.560 20.410 41.120 61.530 -62.470 124.000 Vertical 13.560 20.410 38.130 58.540 -65.460 124.000 Z-axis Quasi-Peak Horizontal 13.560 20.410 40.130 60.540 -63.460 124.000 Vertical 13.560 20.410 39.960 60.370 -63.630 124.000 Note: 1. Limit=84dBμV/m + 40*Log (30(m)/3(m))=124dBμV/m 2. All Readings below 1GHz are Quasi-Peak, above are average value. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 17 of 28

Report No. 1510151R-RFUSP17V00 Product : TABLET PC Test Item : General Radiated Emission Data (below 30MHz) Test Site : No.3 OATS Test Mode : Mode 1: Transmit mode Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz dB dBμV dBμV/m dB dBμV/m Horizontal 27.120 19.950 25.220 45.170 -24.370 69.540 Vertical 27.120 19.950 24.950 44.900 -24.640 69.540 Note: 1. Limit=29.54dBμV/m + 40*Log (30(m)/3(m))=69.54dBμV/m 2. All Readings below 1GHz are Quasi-Peak, above are average value. 3. “ ” means the worst emission level. 4. Measurement Level = Reading Level + Correct Factor. Page: 18 of 28

Report No. 1510151R-RFUSP17V00 Product : TABLET PC Test Item : General Radiated Emission Data (above 30MHz) Test Site : No.3 OATS Test Mode : Mode 1: Transmit mode Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz dB dBμV dBμV/m dB dBμV/m Horizontal QP Detector 107.600 -7.597 34.490 26.893 -16.607 43.500 225.940 -9.647 44.883 35.236 -10.764 46.000 365.620 0.382 33.763 34.145 -11.855 46.000 600.360 3.472 26.384 29.856 -16.144 46.000 800.180 6.417 24.940 31.357 -14.643 46.000 951.500 6.993 24.981 31.974 -14.026 46.000 Vertical QP Detector 43.580 -10.919 41.976 31.057 -8.943 40.000 262.800 -4.944 33.778 28.834 -17.166 46.000 511.120 0.783 23.826 24.609 -21.391 46.000 689.600 2.302 22.662 24.964 -21.036 46.000 817.640 2.966 23.702 26.668 -19.332 46.000 920.460 3.272 23.924 27.196 -18.804 46.000 Note: 1. All Readings below 1GHz are Quasi-Peak, above are average value. 2. “ ” means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 19 of 28

Report No. 1510151R-RFUSP17V00 4. Band Edge 4.1. Test Equipment Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 3 X Magnetic Loop Teseq HLA6121/ 37133 Sep., 2014 Antenna X Bilog Antenna Schaffner Chase CBL6112B/ 2707 Jun., 2014 X EMI Test Receiver R&S ESCS 30/838251/ 001 Jun., 2014 X QTK(Arnist) RG 214/ LC003-RG Coaxial Cable Jun., 2014 X Coaxial signal switch Arnist MP59B/ 6200798682 Jun., 2014 Note: 1. All equipments are calibrated with traceable calibrations. Each calibration is traceable to the national or international standards. 2. The test instruments marked with “X” are used to measure the final test results. 4.2. Test Setup 3m FRP Dome Antenna Mast EUT Broadband or Loop Non-Conducted Table Antenna 1m 80cm Fully soldered Metal Ground Test To Receiver Receiver Page: 20 of 28

Report No. 1510151R-RFUSP17V00 4.3. Limits In any 9 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 50 dB below that in the 9 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. Attenuation below the general limits specified in Section 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). 4.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ANSI C63.10: 2013 on radiated measurement. The bandwidth below 30MHz setting on the field strength meter is 9kHz and above 30MHz is 120kHz. 4.5. Uncertainty Radiated is ± 2.6 dB Page: 21 of 28

Report No. 1510151R-RFUSP17V00 4.6. Test Result of Band Edge Product : TABLET PC Test Item : Band Edge Data Test Site : No.3 OATS Test Mode : Mode 1: Transmit mode RF Radiated Measurement (Horizontal) Emission Frequency Correct Factor Reading Level QP Limit Level Result (MHz) (dB) (dBμV) (dBμV/m) (dBμV/m) 13.110 20.430 26.260 46.690 69.540 Pass 13.360 20.420 27.140 47.560 69.540 Pass 13.410 20.420 27.030 47.450 69.540 Pass 14.010 20.400 26.960 47.360 69.540 Pass Note: 1. All Readings below 1GHz are Quasi-Peak, above are average value. 2. “ ” means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor (Vertical) Emission Frequency Correct Factor Reading Level QP Limit Level Result (MHz) (dB) (dBμV) (dBμV/m) (dBμV/m) 13.110 20.430 24.230 44.660 69.540 Pass 13.360 20.420 23.690 44.110 69.540 Pass 13.410 20.420 24.520 44.940 69.540 Pass 14.010 20.400 26.300 46.700 69.540 Pass Note: 1. All Readings below 1GHz are Quasi-Peak, above are average value. 2. “ ” means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 22 of 28

Report No. 1510151R-RFUSP17V00 5. Frequency Tolerance 5.1. Test Equipment Equipment Manufacturer Model No./Serial No. Last Cal. Spectrum Analyzer R&S FSP40 / 100170 Jun., 2014 Spectrum Analyzer Agilent E4407B / US39440758 Jun., 2014 X Spectrum Analyzer Agilent N9010A / MY48030495 Apr., 2014 X Temperature Chamber TDE CHM 150CT March, 2014 Note: All equipments are calibrated every one year. 5.2. Test Setup Power Meter 12dBuV   Temperature Chamber Power Supply 5.3. Limits The frequency tolerance of the carrier signal shall be maintained within ±0.01％ of the operating frequency. 5.4. Test Procedure The over operating frequency over a temperature variation of -20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85％ to 115％ of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 5.5. Uncertainty ± 150 Hz Page: 23 of 28

Report No. 1510151R-RFUSP17V00 5.6. Test Result of Frequency Stability Product : TABLET PC Test Item : Frequency Tolerance Test Site : Temperature Chamber Test Mode : Mode 1: Transmit mode Temperature Voltage Observe Declared Read Tolerance Limit (℃) (V) Time Frequency Frequency (%) (%) (MHz) (MHz) start 13.56 13.56075 0.005531 2mins 13.56 13.56075 0.005531 20 120 ± 0.01 % 5mins 13.56 13.56075 0.005531 10mins 13.56 13.56075 0.005531 start 13.56 13.56075 0.005531 2mins 13.56 13.56075 0.005531 20 138 ± 0.01 % 5mins 13.56 13.56075 0.005531 10mins 13.56 13.56075 0.005531 start 13.56 13.56075 0.005531 2mins 13.56 13.56075 0.005531 20 102 ± 0.01 % 5mins 13.56 13.56075 0.005531 10mins 13.56 13.56075 0.005531 start 13.56 13.56031 0.002286 2mins 13.56 13.56031 0.002286 50 120 ± 0.01 % 5mins 13.56 13.56031 0.002286 10mins 13.56 13.56031 0.002286 start 13.56 13.56047 0.003466 2mins 13.56 13.56047 0.003466 40 120 ± 0.01 % 5mins 13.56 13.56047 0.003466 10mins 13.56 13.56047 0.003466 start 13.56 13.56022 0.001622 2mins 13.56 13.56022 0.001622 30 120 ± 0.01 % 5mins 13.56 13.56022 0.001622 10mins 13.56 13.56022 0.001622 Page: 24 of 28

Report No. 1510151R-RFUSP17V00 start 13.56 13.56004 0.000295 2mins 13.56 13.56004 0.000295 10 120 ± 0.01 % 5mins 13.56 13.56004 0.000295 10mins 13.56 13.56004 0.000295 start 13.56 13.56004 0.000295 2mins 13.56 13.56004 0.000295 0 120 ± 0.01 % 5mins 13.56 13.56004 0.000295 10mins 13.56 13.56004 0.000295 start 13.56 13.56092 0.006785 2mins 13.56 13.56092 0.006785 -10 120 ± 0.01 % 5mins 13.56 13.56092 0.006785 10mins 13.56 13.56092 0.006785 start 13.56 13.56092 0.006785 2mins 13.56 13.56092 0.006785 -20 120 ± 0.01 % 5mins 13.56 13.56092 0.006785 10mins 13.56 13.56092 0.006785 Page: 25 of 28

Report No. 1510151R-RFUSP17V00 6. EMI Reduction Method During Compliance Testing No modification was made during testing. Page: 26 of 28

Report No. 1510151R-RFUSP17V00 Attachment 1: EUT Test Photographs Page: 27 of 28

Report No. 1510151R-RFUSP17V00 Attachment 2: EUT Detailed Photographs Page: 28 of 28


Document Created: 2015-02-26 14:31:19
Document Modified: 2015-02-26 14:31:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC