Test Report WCDMA

FCC ID: 2ABOSPLATVIEW

Test Report

Download: PDF

FCCID_3698937

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

TEST REPORT

December 02, 2017
Test Report No. : LCS171113053AEF ______________________________________________________________________________________________

Date of issue

Equipment under Test : Tablet with 3G

Model /Type : PLATINUM VIEW

Listed Models : MW-7617L, MW-7617, MW7617L-3G, MW-7617Q, MID-7617L,
MD-7617L

Applicant : Sky Phone LLC
Address : 1348 Washington Av. Suite 350, Miami Beach, Florida, United
States 33139

Manufacturer : Dongguan Lianzhou Electronic Technology Co., Ltd
Address : Hena Science and Technology Park, Yu Quan Industry, Huang
Dong Village, Feng Gang Town, Dongguan, China

Factory : SKY PHONE LLC d/s/a SKY DEVICES
Address : 1348 WASHINTON AVE. #350. MIAMI BEACH, FL 33139 Miami
Beach - FL 33139, Shenzhen, China

Test Result: PASS

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 2 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

Revison History
Revision Issue Date Revisions Revised By
00 December 02, 2017 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

Contents

1 TEST ST AND ARDS ................................................................. 5

2 SUMM ARY ............................................................................ 6

2.1 General Remarks 6
2.2 Product Description 6
2.3 Equipment under Test 7
2.4 Short description of the Equipment under Test (EUT) 7
2.5 Internal Identification of AE used during the test 7
2.6 Normal Accessory setting 7
2.7 EUT configuration 8
2.8 Related Submittal(s) / Grant (s) 8
2.9 Modifications 8
2.10 General Test Conditions/Configurations 8

3 TEST ENVIRONMENT .............................................................. 9

3.1 Address of the test laboratory 9
3.2 Test Facility 9
3.3 Environmental conditions 9
3.4 Test Description 9
3.5 Equipments Used during the Test 11
3.6 Measurement uncertainty 12

4 TEST CONDITIONS AND RESULTS........................................... 13

4.1 Output Power 13
4.2 Radiated Spurious Emssion 16
4.3 Occupied Bandwidth and Emission Bandwith 19
4.4 Band Edge Compliance 21
4.5 Spurious Emssion on Antenna Port 23
4.6 Frequency Stability Test 28
4.7 Peak-to-Average Ratio (PAR) 30

5 TEST SETUP PHOTOS OF THE EUT ......................................... 32

6 EXT ERNAL PHOTOS OF THE EUT ............................................ 32

7 INTERNAL PHOTOS OF THE EUT ............................................ 32

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

1 TEST STANDARDS

The tests were performed according to following standards:

FCC Part 22: Private Land Mobile Radio Services.
FCC Part 24: Public Mobile Services.
ANSI C63.26:2015: American National Standard for Compliance Testing of Transmitters Used in Licensed
Radio Services
47 CFR FCC Part 15 Subpart B: Unintentional Radiators.
FCC Part 2: Frequency Allocations And Radio Treaty Matters: General Rules And Regulations.
ANSI C63.4:2014: Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electronic Equipment in the Range of 9 kHz to 40 GHz.
FCCKDB971168D01 Power Meas License Digital Systems

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

2 SUMMARY

2.1 General Remarks
Date of receipt of test sample : November 17, 2017

Testing commenced on : December 02, 2017

Testing concluded on : December 02, 2017

2.2 Product Description
The Sky Phone LLC’s Model: PLATINUM VIEW or the “EUT” as referred to in this report; more general
information as follows, for more details, refer to the user’s manual of the EUT.

Name of EUT Tablet with 3G
PLATINUM VIEW, MW-7617L, MW-7617, MW7617L-3G, MW-7617Q,
Model Number
MID-7617L, MD-7617L
PCB board, structure and internal of these model(s) are the same,
Model Declaration
Only the model name and the trade mark is different for these models.
Test Model PLATINUM VIEW
GMSK for GSM/GPRS, 8-PSK for EDGE only Downlink, not support
Modulation Type
uplink mode, QPSK for UMTS
2.0dBi (max.) For GSM 850; 2.0dBi (max.) For GSM 900;
2.0dBi (max.) For DCS 1800; 2.0dBi (max.) For PCS 1900;
Antenna Gain 2.0dBi (max.) For WCDMA Band II
2.0dBi (max.) For WCDMA Band V
2.0dBi (max.) For BT and WLAN
Hardware version K706A
Software version PLATINUMVIEW
GSM/EDGE/GPRS Operation
GSM850/PCS1900/GPRS850/GPRS1900
Frequency Band
UMTS Operation Frequency Band UMTS FDD Band II/V
GSM/EDGE/GPRS Supported GSM/GPRS; Support EDGE(Downlink Only)
GSM Release Version R99
GSM/EDGE/GPRS Power Class GSM850:Power Class 4/ PCS1900:Power Class 1
GPRS/EDGE Multislot Class GPRS/EDGE: Multi-slot Class 12
GPRS operation mode Class B
WCDMA Release Version R8
HSDPA Release Version Release 8
HSUPA Release Version Release 6
DC-HSUPA Release Version Not Supported
UMTS Power Class Class 3
IEEE 802.11b: DSSS(CCK,DQPSK,DBPSK)
IEEE 802.11g: OFDM(64QAM, 16QAM, QPSK, BPSK)
WLAN FCC Modulation Type
IEEE 802.11n HT20: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11n HT40: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11b:2412-2462MHz
IEEE 802.11g:2412-2462MHz
WLAN FCC Operation frequency
IEEE 802.11n HT20:2412-2462MHz
IEEE 802.11n HT40:2422-2452MHz
Antenna Type PIFA Antenna
BT Modulation Type GFSK,8-DPSK,π/4-DQPSK(BT V4.0)
Extreme temp. Tolerance -20°C to +40°C
GPS function Support and only RX
FM function Support and only RX
NFC Function Not Supported
Extreme vol. Limits 3.40VDC to 4.20VDC (nominal: 3.70VDC)

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

2.7 EUT configuration
The following peripheral devices and interface cables were connected during the measurement:

● - supplied by the manufacturer

○ - supplied by the lab

○ Power Cable Length (m) : /
Shield : /
Detachable : /
○ Multimeter Manufacturer : /
Model No. : /

2.8 Related Submittal(s) / Grant (s)
This submittal(s) (test report) is intended for FCC ID: 2ABOSPLATVIEW filing to comply with FCC Part 22
and Part 24 Rules.

2.9 Modifications
No modifications were implemented to meet testing criteria.

2.10 General Test Conditions/Configurations

2.10.1 Test Modes

NOTE: The test mode(s) are selected according to relevant radio technology specifications.

Test Mode Test Modes Description
UMTS/TM1 WCDMA system, QPSK modulation
UMTS/TM2 HSDPA system, QPSK modulation
UMTS/TM3 HSUPA system, QPSK modulation

Note:
1. This EUT owns two SIM cards, SIM 1 support GSM/UMTS, SIM 2 only support GSM;
2. As WCDMA, HSDPA and HSUPA with the same emission designator, test result recorded in this report at
the worst case UMTS/TM1 only after exploratory scan.

2.10.2 Test Environment
Environment Parameter Selected Values During Tests
Relative Humidity Ambient
Temperature TN 25 degree
VL 3.40 V
Voltage VN 3.70 V
VH 4.20 V

NOTE: VL=lower extreme test voltage VN=nominal voltage
VH=upper extreme test voltage TN=normal temperature

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

3 TEST ENVIRONMENT

3.1 Address of the test laboratory
Shenzhen LCS Compliance Testing Laboratory Ltd

1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong,
China
The sites are constructed in conformance with the requirements of ANSI C63.4 (2014) and CISPR
Publication 22.

3.2 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:

FCC Registration Number. is 254912.
Industry Canada Registration Number. is 9642A-1.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
NVLAP Registration Code is 600167-0

3.3 Environmental conditions
During the measurement the environmental conditions were within the listed ranges:

Temperature: 15-35 ° C

Humidity: 30-60 %

Atmospheric pressure: 950-1050mbar
(1)expressed at approximately the 95% confidence level using a coverage factor of k=1.96.

3.4 Test Description

3.4.1 Cellular Band (824-849MHz paired with 869-894MHz)
Test Item FCC Rule No. Requirements Verdict
Effective(Isotropic) Radiated §2.1046, FCC: ERP ≤ 7W.
PASS
Output Power §22.913 ISED: ERP ≤ 11.5W.
Modulation Characteristics §2.1047 Digital modulation N/A
OBW: No limit.
Bandwidth §2.1049 PASS
EBW: No limit.
≤-13dBm/1%*EBW, in 1MHz
§2.1051,
Band Edges Compliance bands immediately outside and PASS
§22.917
adjacent to the frequency block.
≤ -13dBm/100kHz,
Spurious Emission at §2.1051, from 9 KHz to 10th harmonics
PASS
Antenna Terminals §22.917 but outside authorized
operating frequency ranges.
Field Strength of Spurious §2.1053,
≤ -13dBm/100kHz. PASS
Radiation §22.917
§2.1055,
Frequency Stability ≤ ±2.5ppm. PASS
§22.355
Peak-Average Ratio N/A ≤13dB PASS
Receiver Spurious Emissions N/A -- PASS
NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

3.4.2 PCS Band (1850-1915MHz paired with 1930-1995MHz)
Test Item FCC Rule No. Requirements Verdict
Effective(Isotropic) Radiated §2.1046,
EIRP ≤ 2W PASS
Output Power §24.232
§2.1046,
Peak-Average Ratio ≤13dB PASS
§24.232
Modulation Characteristics §2.1047 Digital modulation N/A
OBW: No limit.
Bandwidth §2.1049 PASS
EBW: No limit.
≤ -13dBm/1%*EBW, In 1MHz bands
§2.1051,
Band Edges Compliance immediately outside and adjacent to PASS
§24.238
the frequency block.
≤-13dBm/1MHz, from 9 KHz to10th
Spurious Emission at §2.1051,
harmonics but outside authorized PASS
Antenna Terminals §24.238
Operating frequency ranges.
Field Strength of Spurious §2.1053,
≤ -13dBm/1MHz. PASS
Radiation §24.238
§2.1055,
Frequency Stability ≤ ±2.5ppm. PASS
§24.235
Receiver Spurious Emissions N/A -- PASS
NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.

Remark: 1.The measurement uncertainty is not included in the test result.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

3.6 Measurement uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that there
may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was
calculated for all measurements listed in this test report acc. to ETSI TR 100 028 “ Electromagnetic
compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio
equipment characteristics” and is documented in the Shenzhen LCS Compliance Testing Laboratory Ltd.
quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices
similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of
continued compliance of the device.

Hereafter the best measurement capability for Shenzhen LCS Compliance Testing Laboratory Ltd. is reported:

Measurement
Test Range Notes
Uncertainty
Radiated Emission 30~1000MHz 3.10 dB (1)
Radiated Emission 1~18GHz 3.80 dB (1)
Radiated Emission 18-40GHz 3.90 dB (1)
Conducted Disturbance 0.15~30MHz 1.63 dB (1)
Conducted Power 9KHz~18GHz 0.61 dB (1)
Spurious RF Conducted Emission 9KHz~40GHz 1.22 dB (1)
Band Edge Compliance of RF Emission 9KHz~40GHz 1.22 dB (1)
Occuiped Bandwidth 9KHz~40GHz - (1)

(1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level
using a coverage factor of k=1.96.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF
5. A amplifier should be connected to the Signal Source output port. And the cable should be connect
between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain
(Ga) and the Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea+ PAg - Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi.

TEST LIMIT

According to 22.913(a)(5), 24.232(c), the ERP(EIRP) should be not exceeding following table limits:

Burst Average EIRP
UMTS Band II FCC: ≤33.00dBm (2W)

Burst Average ERP
UMTS Band V FCC: ≤38.45dBm (7W)

TEST RESULTS

Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
4. Margin = Emission Level - Limit
5. We test the H direction and V direction recorded worst case.

UMTS/TM1/UMTS Band II
Ga Burst
Frequency PMea Pcl Antenna PAg Average Limit Margin
Polarization
(MHz) (dBm) (dB) Gain (dB) EIRP (dBm) (dB)
(dB) (dBm)
1852.40 -19.07 4.03 8.38 35.51 20.79 33.01 -12.22 V
1880.00 -18.58 4.08 8.33 35.56 21.23 33.01 -11.78 V
1907.60 -19.93 4.14 8.26 35.63 19.82 33.01 -13.19 V

UMTS/TM1/UMTS Band V
Ga Burst
Frequency PMea Pcl Antenna Correction PAg Average Limit Margin
Polarization
(MHz) (dBm) (dB) Gain (dB) (dB) ERP (dBm) (dB)
(dB) (dBm)
826.40 -16.30 3.45 8.45 2.15 33.79 20.34 38.45 -18.11 V
836.40 -16.04 3.49 8.45 2.15 33.85 20.62 38.45 -17.83 V
846.60 -17.13 3.55 8.36 2.15 33.88 19.41 38.45 -19.04 V

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

5. A amplifier should be connected to the Signal Source output port. And the cable should be connect
between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain
(Ga) and the Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea+ PAg - Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP -2.15dBi.
8. In order to make sure test results more clearly,we set frequency range and sweep time for difference
frequency range as follows table:

Working Subrange Sweep time
RBW VBW
Frequency (GHz) (s)
0.00009~0.15 1KHz 3KHz 30
0.00015~0.03 10KHz 30KHz 10
0.03~1 100KHz 300KHz 10
UMTS/TM1/
1~2 1 MHz 3 MHz 2
WCDMA Band V
2~5 1 MHz 3 MHz 3
5~8 1 MHz 3 MHz 3
8~10 1 MHz 3 MHz 3
0.00009~0.15 1KHz 3KHz 30
0.00015~0.03 10KHz 30KHz 10
0.03~1 100KHz 300KHz 10
1~2 1 MHz 3 MHz 2
UMTS/TM1/ 2~5 1 MHz 3 MHz 3
WCDMA Band II 5~8 1 MHz 3 MHz 3
8~11 1 MHz 3 MHz 3
11~14 1 MHz 3 MHz 3
14~18 1 MHz 3 MHz 3
18~20 1 MHz 3 MHz 2

TEST LIMITS

According to 24.238, 22.917 and 27.54 specify that the power of any emission outside of the authorized
operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 +
10 log(P) dB.
The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log
(P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum
attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0
dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the
specification from relative to absolute terms is carried out.

Frequency Channel Frequency Range Verdict
Low 9 KHz – 10 GHz PASS
UMTS/TM1/ WCDMA
Middle 9 KHz – 10 GHz PASS
Band V
High 9 KHz – 10 GHz PASS
Low 9 KHz – 20 GHz PASS
UMTS/TM1/ WCDMA
Middle 9 KHz – 20 GHz PASS
Band II
High 9 KHz – 20 GHz PASS

TEST RESULTS

Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
4. Margin = EIRP - Limit

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 17 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

UMTS/TM1/ WCDMA Band II _ Low Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3704.80 -39.15 5.26 3.00 9.88 -34.53 -13.00 -21.53 H
5557.20 -44.75 6.11 3.00 11.36 -39.50 -13.00 -26.50 H
3704.80 -44.24 5.26 3.00 9.88 -39.62 -13.00 -26.62 V
5557.20 -48.74 6.11 3.00 11.36 -43.49 -13.00 -30.49 V

UMTS/TM1/ WCDMA Band II _ Middle Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3760.00 -37.99 5.32 3.00 10.03 -33.28 -13.00 -20.28 H
5640.00 -44.14 6.19 3.00 11.41 -38.92 -13.00 -25.92 H
3760.00 -43.42 5.32 3.00 10.03 -38.71 -13.00 -25.71 V
5640.00 -48.10 6.19 3.00 11.41 -42.88 -13.00 -29.88 V

UMTS/TM1/ WCDMA Band II _ High Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3815.20 -43.41 5.36 3.00 9.62 -39.15 -13.00 -26.15 H
5722.80 -51.53 6.24 3.00 11.46 -46.31 -13.00 -33.31 H
3815.20 -46.34 5.36 3.00 9.62 -42.08 -13.00 -29.08 V
5722.80 -53.33 6.24 3.00 11.46 -48.11 -13.00 -35.11 V

UMTS/TM1/ WCDMA Band V _ Low Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1652.80 -47.83 3.86 3.00 8.56 -43.13 -13.00 -30.13 H
2479.20 -49.39 4.29 3.00 6.98 -46.70 -13.00 -33.70 H
1652.80 -44.32 3.86 3.00 8.56 -39.62 -13.00 -26.62 V
2479.20 -44.61 4.29 3.00 6.98 -41.92 -13.00 -28.92 V

UMTS/TM1/ WCDMA Band V _ Middle Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1672.80 -49.41 3.90 3.00 8.58 -44.73 -13.00 -31.73 H
2509.20 -51.12 4.32 3.00 6.80 -48.64 -13.00 -35.64 H
1672.80 -45.49 3.90 3.00 8.58 -40.81 -13.00 -27.81 V
2509.20 -45.46 4.32 3.00 6.80 -42.98 -13.00 -29.98 V

UMTS/TM1/ WCDMA Band V _ High Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1693.20 -51.84 3.91 3.00 9.06 -46.69 -13.00 -33.69 H
2539.80 -54.21 4.32 3.00 6.65 -51.88 -13.00 -38.88 H
1693.20 -49.09 3.91 3.00 9.06 -43.94 -13.00 -30.94 V
2539.80 -51.00 4.32 3.00 6.65 -48.67 -13.00 -35.67 V

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 18 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

TEST RESULTS

Spurious RF
Frequency Limits
Test Mode Channel Conducted Emission Verdict
(MHz) (dBm)
(dBm)
4132 826.40 <-13dBm -13dBm
UMTS/TM1/WCDMA
4182 836.40 <-13dBm -13dBm PASS
Band V
4233 846.60 <-13dBm -13dBm
9262 1852.40 <-13dBm -13dBm
UMTS/TM1/WCDMA
9400 1880.00 <-13dBm -13dBm PASS
Band II
9538 1907.60 <-13dBm -13dBm

Remark:
1. Test results including cable loss;
2. Please refer to following plots;
3. Not reorded test plots from 9 KHz to 30 MHz as emission levels 20dB lower than emission limit;

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 24 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

TEST LIMITS

For Hand carried battery powered equipment
According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the
received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability.
The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized
frequency block. As this transceiver is considered "Hand carried, battery powered equipment" Section
2.1055(d)(2) applies. This requires that the lower voltage for frequency stability testing be specified by the
manufacturer. This transceiver is specified to operate with an input voltage of between 3.40VDC and 4.20VDC,
with a nominal voltage of 3.80DC. Operation above or below these voltage limits is prohibited by transceiver
software in order to prevent improper operation as well as to protect components from overstress. These
voltages represent a tolerance of -10 % and +12.5 %. For the purposes of measuring frequency stability these
voltage limits are to be used.

For equipment powered by primary supply voltage
According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the
received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability.
The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized
frequency block. For this EUT section 2.1055(d)(1) applies. This requires varying primary supply voltage from
85 to 115 percent of the nominal value for other than hand carried battery equipment.

TEST RESULTS

UMTS/TM1/WCDMA Band II
Temperature Frequency Frequency Limit
DC Power Verdict
(℃) error(Hz) error(ppm) (ppm)
3.40 25 -3 -0.002 2.50 PASS
3.70 25 -9 -0.005 2.50 PASS
4.20 25 7 0.004 2.50 PASS
3.70 -30 6 0.003 2.50 PASS
3.70 -20 -15 -0.008 2.50 PASS
3.70 -10 8 0.004 2.50 PASS
3.70 0 -2 -0.001 2.50 PASS
3.70 10 -15 -0.008 2.50 PASS
3.70 20 7 0.004 2.50 PASS
3.70 30 16 0.009 2.50 PASS
3.70 40 -9 -0.005 2.50 PASS
3.70 50 15 0.008 2.50 PASS

UMTS/TM1/WCDMA Band V
Temperature Frequency Frequency Limit
DC Power Verdict
(℃) error(Hz) error(ppm) (ppm)
3.40 25 -9 -0.011 2.50 PASS
3.70 25 -5 -0.006 2.50 PASS
4.20 25 13 0.016 2.50 PASS
3.70 -30 -10 -0.012 2.50 PASS
3.70 -20 -1 -0.001 2.50 PASS
3.70 -10 -5 -0.006 2.50 PASS
3.70 0 -14 -0.017 2.50 PASS
3.70 10 15 0.018 2.50 PASS
3.70 20 -18 -0.022 2.50 PASS
3.70 30 -5 -0.006 2.50 PASS
3.70 40 -9 -0.011 2.50 PASS
3.70 50 -11 -0.013 2.50 PASS

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 32

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ABOSPLATVIEW Report No.: LCS171113053AEF

5 Test Setup Photos of the EUT

Please refer to separated files for Test Setup Photos of the EUT.

6 External Photos of the EUT

Please refer to separated files for External Photos of the EUT.

7 Internal Photos of the EUT

Please refer to separated files for Internal Photos of the EUT.

.........................End of Report.........................

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 32 of 32

Document Created: 2017-12-29 17:57:33
Document Modified: 2017-12-29 17:57:33

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC