Test Report-WMD05_CDMA FCC

FCC ID: 2ABGH-RC555L

Test Report

Download: PDF
FCCID_3611873

TEST REPORT No. I17Z61374-WMD05 for Reliance Communications, LLC. GSM/CDMA/WCDMA/LTE Model Name: RC555L FCC ID: 2AGBH-RC555L with Hardware Version: V1.1 Software Version: ORBIC-RC555L_V1.6.3 Issued Date: 2017-9-26 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S.Government.. Test Laboratory: Test Firm Designation Number:CN5017 CTTL, Telecommunication Technology Labs, CAICT No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504 Email: cttl_terminals@caict.ac.cn, website: www.caict.ac.cn

No. I17Z61374-WMD05 Page2 of 25 REPORT HISTORY Report Number Revision Description Issue Date I17Z61374-WMD05 Rev.0 1st edition 2017-9-26

No. I17Z61374-WMD05 Page3 of 25 CONTENTS 1. TEST LABORATORY ......................................................................................................................... 4 1.1. TESTING LOCATION .................................................................................................................... 4 1.2. TESTING ENVIRONMENT ........................................................................................................... 4 1.3. PROJECT DATA .............................................................................................................................. 4 1.4. SIGNATURE ..................................................................................................................................... 4 2. CLIENT INFORMATION ................................................................................................................... 5 2.1. APPLICANT INFORMATION ....................................................................................................... 5 2.2. MANUFACTURER INFORMATION ............................................................................................ 5 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................. 6 3.1. ABOUT EUT ..................................................................................................................................... 6 3.2. INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST .................................... 6 3.3. INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ....................................... 6 3.4. NORMAL ACCESSORY SETTING ............................................................................................... 7 3.5. GENERAL DESCRIPTION ............................................................................................................ 7 4. REFERENCE DOCUMENTS ............................................................................................................. 7 4.1. REFERENCE DOCUMENTS FOR TESTING ............................................................................. 7 5. LABORATORY ENVIRONMENT ..................................................................................................... 8 6. SUMMARY OF TEST RESULTS ....................................................................................................... 9 7. TEST EQUIPMENTS UTILIZED .................................................................................................... 10 ANNEX A: MEASUREMENT RESULTS.................................................................................................11 A.1 OUTPUT POWER ..............................................................................................................................11 A.2 FREQUENCY STABILITY ............................................................................................................... 12 A.3 OCCUPIED BANDWIDTH .............................................................................................................. 14 A.4 EMISSION BANDWIDTH................................................................................................................ 16 A.5 CONDUCTED SPURIOUS EMISSION ........................................................................................... 18 ANNEX B: ACCREDITATION CERTIFICATE..................................................................................... 25

m> No. 117261374—WMDO5 «@7771 Page4 of 25 lt.__—cat 1. Test Laboratory 1.1. Testing Location Location 1: CTTL(huayuan North Road) Address: No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191 Location 2: CTTL(Shouxiang) Address: No. 51 Shouxiang Science Building, Xueyuan Road, Haidian District, Beijing, P. R. China 100191 1.2. Testing Environment Normal Temperature: 15—35°C Relative Humidity: 20—80% 1.3. Project data Testing Start Date: 2017—9—6 Testing End Date: 2017—9—26 1.4. Signature Shen Yi (Prepared this test report) Al 7 Zhou Yu (Reviewed this test report) # ‘K‘: Zhao Hui Lin Deputy Director of the laboratory {Approved this test report)

No. I17Z61374-WMD05 Page5 of 25 2. Client Information 2.1. Applicant Information Company Name: Reliance Communications, LLC. Address /Post: 555 Wireless BLVD, Hauppauge NY 11788 City: New York Postal Code: / Country: U.S.A Contact Person: Saqib Ghouri Contact Email: saqib.ghouri@reliance.us Telephone: +92 317 512 6111 Fax: / 2.2. Manufacturer Information Company Name: Unimaxcomm. Room 602, Building-B, Shenzhen Software Park T3, Hi-Tech Park Address /Post: South, Nan Shan District, Shenzhen, China City: Shenzhen Postal Code: 518000 Country: China Contact Person: Chunli.He Contact Email: hchunli@unimaxcomm.com Telephone: +86 130 7785 5257 Fax: 0755-86638991

No. I17Z61374-WMD05 Page6 of 25 3. Equipment Under Test (EUT) and Ancillary Equipment (AE) 3.1. About EUT Description GSM/CDMA/WCDMA/LTE Model RC555L FCC ID 2AGBH-RC555L Frequency CDMA800MHz(BC0);CDMA1900MHz(BC1);CDMA2ND800MHz(BC10) Antenna Embedded Power supply Battery or Charger (AC Adaptor) Extreme vol. Limits 3.6VDC to 4.3VDC (nominal: 3.8 VDC) Extreme temp. Tolerance -10°C to +40°C Note: Components list, please refer to documents of the manufacturer; it is also included in the original test record of Telecommunication Metrology Center of MIIT of People’s Republic of China. 3.2. Internal Identification of EUT used during the test EUT ID* SN or IMEI HW Version SW Version Date of receipt UT24a 358924080002020 V1.1 ORBIC-RC555L_V1.6.3 2017-9-6 *EUT ID: is used to identify the test sample in the lab internally. 3.3. Internal Identification of AE used during the test AE ID* Description SN AE1 Battery / AE2 Normal Charger / AE1 Model RC555L Manufacturer Veken Capacitance 3000mAh Nominal Voltage 3.8V AE2 Model RC555L Manufacturer BLJ *AE ID: is used to identify the test sample in the lab internally.

No. I17Z61374-WMD05 Page7 of 25 3.4. Normal Accessory setting Fully charged battery was used during the test. 3.5. General Description The Equipment Under Test (EUT) is a model of GSM/CDMA/WCDMA/LTE with integrated antenna. It consists of normal options: lithium battery, charger. Manual and specifications of the EUT were provided to fulfil the test. 4. Reference Documents 4.1. Reference Documents for testing The following documents listed in this section are referred for testing. Reference Title Version FCC Part 90 PRIVATE LAND MOBILE RADIO SERVICES 10-1-16 Edition FCC Part 2 FREQUENCY ALLOCATIONS AND RADIO TREATY 10-1-16 MATTERS;GENERAL RULES AND REGULATIONS Edition ANSI/TIA-603-D Land Mobile FM or PM Communications Equipment 2010 Measurement and Performance Standards KDB971168 D01 Measurement Guidance for Certification of Licensed Digital v02r02 Transmitters

No. 117261374—WMDO5 (llélll) Page8 of 25 5. LABORATORY ENVIRONMENT Shielding chamber did not exceed following limits along the RF testing: Temperature Min. = 15 °C, Max. = 35 °C Relative humidity Min. =20 %, Max. = 80 %

No. I17Z61374-WMD05 Page9 of 25 6. SUMMARY OF TEST RESULTS Items List Clause in FCC rules Verdict 1 Output Power 90.635 Pass 2 Frequency Stability 2.1055/90.213 Pass 3 Occupied Bandwidth 2.1049 Pass 4 Emission Bandwidth 90.1215 Pass 5 Conducted Spurious Emission 90.691 Pass

No. I17Z61374-WMD05 Page10 of 25 7. Test Equipments Utilized SERIES CALIBRATION CAL DUE NO. NAME TYPE PRODUCER NUMBER INTERVAL DATE 1 Spectrum Analyzer FSV30 101576 R&S 1 Year 2018-2-1 Wireless GB461603 2 Communications Test 8960(E5515C) Agilent 1 Year 2018-7-22 13 Set 3 Climatic chamber SH-641 92009050 ESPEC 2 Years 2018-2-16

No. I17Z61374-WMD05 Page11 of 25 ANNEX A: MEASUREMENT RESULTS A.1 OUTPUT POWER A.1.1 Summary During the process of testing, the EUT was controlled via Agilent Wireless Communications Test Set (8960(E5515C)) to ensure max power transmission and proper modulation. This result is peak output power conducted measurements for the EUT. In all cases, output power is within the specified limits. A.1.2 Method of Measurements The EUT was set up for the max output power with pseudo random data modulation. The power was measured with Rhode & Schwarz Spectrum Analyzer FSV30 (average). These measurements were done at 2 frequencies of CDMA BC10 (bottom and top of operational frequency range) for 1x RTT and 1xEVDO. The measurement method is from KDB 971168 D01 5.2.1: a) Set span to at least 1.5 times the OBW. b) Set RBW = 1-5% of the OBW, not to exceed 1 MHz. c) Set VBW ≥ 3 × RBW. d) Set number of points in sweep ≥ 2 × span / RBW. e) Sweep time = auto-couple. f) Detector = RMS (power averaging). g) If the EUT can be configured to transmit continuously (i.e., burst duty cycle ≥ 98%), then set the trigger to free run. h) If the EUT cannot be configured to transmit continuously (i.e., burst duty cycle < 98 %), then use a sweep trigger with the level set to enable triggering only on full power bursts and configure the EUT to transmit at full power for the entire duration of each sweep. Ensure that the sweep time is less than or equal to the transmission burst duration. i) Trace average at least 100 traces in power averaging (i.e., RMS) mode. j) Compute the power by integrating the spectrum across the OBW of the signal using the instrument’s band power measurement function, with the band limits set equal to the OBW band edges. If the instrument does not have a band power function, then sum the spectrum levels (in linear power units) at intervals equal to the RBW extending across the entire OBW of the spectrum. A.1.3 Measurement results CDMA BC10 Measurement result Channel power(dBm) Channel Frequency(MHz) 1xEVDO 1xRTT Rel0 RevA 476 817.9 24.32 24.32 24.28 684 823.1 24.24 24.27 24.21

m> No. 117261374—WMDO5 —7"7] Page12 of 25 l A.2 FREQUENCY STABILITY A.2.1 Method of Measurement In order to measure the carrier frequency under the condition of AFC lock, it is necessary to make measurements with the EUT in a "call mode". This is accomplished with the use of Agilent 8960(E5515C) Wireless Communications Test Set. 1. Measure the carrier frequency at room temperature. 2. Subject the EUT to overnight soak at —10°C. 3. With the EUT, powered via nominal voltage, connected to the 8960(E5515C) and in a simulated call on mid channel of CDMA BC10, measure the carrier frequency. These measurements should be made within 2 minutes of Powering up the EUT, to prevent significant self—warming. 4. Repeat the above measurements at 10°C increments from —10°C to +40°C. Allow at least 1 1/2 hours at each temperature, unpowered, before making measurements. 5.. Remeasure carrier frequency at room temperature with nominal voltage. Vary supply voltage from minimum voltage to maximum voltage, in 0.1 Volt increments remeasuring carrier frequency at each voltage. Pause at nominal voltage for 1 1/2 hours unpowered, to allow any self—heating to stabilize, before continuing. 6. Subject the EUT to overnight soak at +40°C. 7. With the EUT, powered via nominal voltage, connected to the 8960(E5515C) and in a simulated call on the centre channel, measure the carrier frequency. These measurements should be made within 2 minutes of Powering up the EUT, to prevent significant self—warming. 8. Repeat the above measurements at 10 C decrements from +40°C to —10°C. Allow at least 1 1/2 hours at each temperature, unpowered, before making measurements. 9. At all temperature levels hold the temperature to +/— 0.5°C during the measurement procedure. A.2.2 Measurement Limit A.2.2.1 For Hand carried battery powered equipment The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. This requires that the lower voltage for frequency stability testing be specified by the manufacturer. This transceiver is specified to operate with an input voltage of between 3.6VDC and 4.3VDC, with a nominal voltage of 3.8VDC. Operation above or below these voltage limits is prohibited by transceiver software in order to prevent improper operation as well as to protect components from overstress. A.2.2.2 For equipment powered by primary supply voltage For Part 90.213, the frequency stability of the transmitter shall be maintained within +2.5ppm of the center frequency. This requires varying primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment.

m> No. 117261374—WMDO5 _ ‘/"/"/, Page13 of 25 l A.2.3 Measurement results CDMA BC 10 Frequency Error vs Voltage Voltage(V) Frequency error(Hz) Frequency error(ppm) 3.6 243 0.003 3.8 2.38 0.003 4.3 2.35 0.003 Frequency Error vs Temperature temperature("C) Frequency error(Hz) Frequency error(ppm) —30 / / —20 / / ~10 2.67 0.003 0 —2.29 0.003 10 2.35 0.003 20 240 0.003 30 247 0.003 40 2.84 0.003 50 / /

No. I17Z61374-WMD05 Page14 of 25 A.3 OCCUPIED BANDWIDTH A.3.1 Occupied Bandwidth Results Similar to conducted emissions; occupied bandwidth measurements are only provided for selected frequencies in order to reduce the amount of submitted data. Data were taken at the extreme and mid frequencies of the CDMA frequency band. The table below lists the measured 99% BW. Spectrum analyzer plots are included on the following pages. Test Condition RBW VBW Span Sweeptime Detector Trace Mode 20KHz 100KHz 5MHz 40ms Peak Max Hold The EUT was set up for the max output power with pseudo random data modulation. Use the Occupied Bandwidth function of SA to measure the 99% bandwidth. CDMA BC10 (99% BW) Channel Occupied Bandwidth (99% BW)(MHz) 476 1.266 684 1.281 CDMA BC10 Channel 476-Occupied Bandwidth (99% BW) Date: 15.SEP.2017 05:03:59

No. I17Z61374-WMD05 Page15 of 25 Channel 684-Occupied Bandwidth (99% BW) Date: 15.SEP.2017 05:05:24

No. I17Z61374-WMD05 Page16 of 25 A.4 EMISSION BANDWIDTH A.4.1Emission Bandwidth Results Similar to conducted emissions; Emission bandwidth measurements are only provided for selected frequencies in order to reduce the amount of submitted data. Data were taken at the extreme and mid frequencies of the CDMA frequency band. Table below lists the measured -26dBc BW. Spectrum analyzer plots are included on the following pages. Test Condition RBW VBW Span Sweeptime Detector Trace Mode 20KHz 100KHz 3.84MHz 40ms Peak Max Hold The EUT was set up for the max output power with pseudo random data modulation. Use the Occupied Bandwidth function of SA to measure the 26dBc bandwidth. CDMA BC10 (-26dBc BW) Channel Emission Bandwidth (–26dBc BW) ( MHz) 476 1.423 684 1.423 CDMA BC10 Channel 476- Emission Bandwidth (-26dBc BW) Date: 15.SEP.2017 05:08:29

No. I17Z61374-WMD05 Page17 of 25 Channel 684- Emission Bandwidth (-26dBc BW) Date: 15.SEP.2017 05:07:06

No. I17Z61374-WMD05 Page18 of 25 A.5 CONDUCTED SPURIOUS EMISSION A.5.1 Measurement Method The spectrum should be investigated from the lowest radio frequency generated in the equipment up to at least the 10th harmonic of the carrier frequency. For CDMA BC10, data taken from 30 MHz to 10GHz. Out-of-band emission requirement shall apply only to the ‘‘outer’’ channels included in an EA license and to spectrum adjacent to interior channels used by incumbent licensees. The emission limits are as follows: For any frequency removed from the EA licensee’s frequency block by up to and including 37.5 kHz, the power of any emission shall be attenuated below the transmitter power (P) in watts by at least 116Log10(f/6.1) decibels or 50 + 10 Log10(P) decibels or 80 decibels, whichever is the lesser attenuation, where f is the frequency removed from the center of the outer channel in the block in kilohertz and where f is greater than 12.5 kHz. For any frequency removed from the EA licensee’s frequency block greater than 37.5 kHz, the power of any emission shall be attenuated below the transmitter power (P) in watts by at least 43 + 10Log10(P) decibels or 80 decibels, whichever is the lesser attenuation, where f is the frequency removed from the center of the outer channel in the block in kilohertz and where f is greater than 37.5 kHz. CDMA BC10 Transmitter Channel Frequency (MHz) 476 817.9 684 823.1

No. I17Z61374-WMD05 Page19 of 25 A.5.2 Measurement result CDMA BC10 A. 5.2.1 Channel 476: 30MHz –1GHz Spurious emission limit –13dBm. NOTE: peak above the limit line is the carrier frequency. Date: 15.SEP.2017 05:10:34 A.5.2.2 Channel 476: 1GHz –2.5GHz Spurious emission limit –13dBm. Date: 15.SEP.2017 05:11:50

No. I17Z61374-WMD05 Page20 of 25 A.5.2.3 Channel 476: 2.5GHz –7.5GHz Spurious emission limit –13dBm. Date: 15.SEP.2017 05:12:51 A.5.2.4 Channel 476: 7.5GHz –10GHz Spurious emission limit –13dBm. Date: 15.SEP.2017 05:14:10

No. I17Z61374-WMD05 Page21 of 25 A.5.2.5 Channel 476: Band Edge Spurious emission limit –20dBm. Date: 15.SEP.2017 06:02:58 A.5.2.6 Channel 476: Outer Extended Band Edge Spurious emission limit –13dBm. Date: 19.SEP.2017 04:51:48

No. I17Z61374-WMD05 Page22 of 25 A. 5.2.7 Channel 684: 30MHz –1GHz Spurious emission limit –13dBm. NOTE: peak above the limit line is the carrier frequency. Date: 15.SEP.2017 05:15:45 A.5.2.8 Channel 684: 1GHz –2.5GHz Spurious emission limit –13dBm. Date: 15.SEP.2017 05:16:57

No. I17Z61374-WMD05 Page23 of 25 A.5.2.9 Channel 684: 2.5GHz –7.5GHz Spurious emission limit –13dBm. Date: 15.SEP.2017 05:18:10 A.5.2.10 Channel 684: 7.5GHz –10GHz Spurious emission limit –13dBm. Date: 15.SEP.2017 05:20:03

No. I17Z61374-WMD05 Page24 of 25 A.5.2.11 Channel 684: Band Edge Spurious emission limit –20dBm. Date: 15.SEP.2017 05:24:15 A.5.2.12 Channel 684: Outer Extended Band Edge Spurious emission limit –13dBm. Date: 15.SEP.2017 05:59:39

No. I17Z61374-WMD05 Page25 of 25 ANNEX B: Accreditation Certificate ***END OF REPORT***


Document Created: 2017-10-17 12:11:46
Document Modified: 2017-10-17 12:11:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC