14_NFL-FLP-DAL TestRpt

FCC ID: 2AANZFLP

Test Report

Download: PDF
FCCID_4037515

Page 1 of 24 Report No.: HK1809271172E FCC TEST REPORT FCC PART 15 SUBPART C 15.235 Test report On Behalf of DGL Group LTD. For Remote Control Model No.: NFL-FLP-DAL, NFL-FLP-PIT, NFL-FLP-NE, NFL-FLP-SEA, NFL-FLP-GBY, NFL-FLP-PHI, NFL-FLP-OAK, NFL-FLP-DEN, NFL-FLP-NYG, NFL-FLP-CHI, NFL-FLP-SF, NFL-FLP-HOU FCC ID: 2AANZFLP Prepared for : DGL Group LTD. 195 Raritan Center Parkway Edison, New Jersey United States 08837 Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Fuhai Street, Bao'an District, Shenzhen City, China Date of Test: Sep. 18, 2018 ~ Sep. 27, 2018 Date of Report: Sep. 27, 2018 Report Number: HK1809271172E

Page 2 of 24 Report No.: HK1809271172E TEST RESULT CERTIFICATION Applicant’s name .................... : DGL Group LTD. Address ..................................... : 195 Raritan Center Parkway Edison, New Jersey United States 08837 Manufacture's Name ............... : DGL Group LTD. Address ..................................... : 195 Raritan Center Parkway Edison, New Jersey United States 08837 Product description Trade Mark: NFL Product name............................ : Remote Control Model and/or type reference ... : NFL-FLP-DAL NFL-FLP-PIT, NFL-FLP-NE, NFL-FLP-SEA, NFL-FLP-GBY, Series Modele NFL-FLP-PHI, NFL-FLP-OAK, NFL-FLP-DEN, NFL-FLP-NYG, NFL-FLP-CHI, NFL-FLP-SF, NFL-FLP-HOU Declaration of Difference All the same except for the model name and front appearance. FCC Rules and Regulations Part 15 Subpart C Section 15.235 Standards ................................. : ANSI C63.10: 2013 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen HUAK Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen HUAK Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ................................................: Date (s) of performance of tests .................: Sep. 18, 2018 ~ Sep. 27, 2018 Date of Issue ...............................................: Sep. 27, 2018 Test Result ...................................................: Pass Testing Engineer : (Gary Qian) Technical Manager : (Eden Hu) Authorized Signatory : (Jason Zhou)

Page 3 of 24 Report No.: HK1809271172E Table of Contents Page 1 . TEST SUMMARY 4 2 . GENERAL INFORMATION 5 2.1 GENERAL DESCRIPTION OF EUT 5 2.2 OPERATION OF EUT DURING TESTING 6 2.3 DESCRIPTION OF TEST SETUP 6 2.4 MEASUREMENT INSTRUMENTS LIST 7 3. RADIATED EMISSION 8 3.1. MEASUREMENT PROCEDURE 8 3.2. TEST SETUP 10 3.3. TEST RESULT 11 4. BANDWIDTH 15 4.1. MEASUREMENT PROCEDURE 15 4.2. TEST SETUP 15 4.3. TEST RESULT 16 5. PHOTOGRAPH OF TEST 17 6. PHOTOGRAPH OF EUT 18

Page 4 of 24 Report No.: HK1809271172E 1. TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS FCC RULES DESCRIPTION OF TEST RESULT §15.235&15.209 Radiated Emission and Band Edges Compliant §15.215 20dB bandwidth Compliant §15.207 Conducted Emission N/A 1.2 TEST FACILITY Test Firm : Shenzhen HUAK Testing Technology Co., Ltd. Address : 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Fuhai Street, Bao'an District, Shenzhen City, China Designation Number: : CN1229 Test Firm Registration Number : 616276 1.3 MEASUREMENT UNCERTAINTY Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.08dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz) = 4.42dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.06dB, k=2

Page 5 of 24 Report No.: HK1809271172E 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Operation Frequency 49.860MHZ Field Strength(3m) 73.49dBuV/m(Peak)@3m Modulation AM Number of channels 1 Hardware Version JH-4116T Software Version NC Antenna Designation Fixed antenna Antenna Gain 0dBi Power Supply DC 9V by Battery

Page 6 of 24 Report No.: HK1809271172E 2.2 OPERATION OF EUT DURING TESTING NO. TEST MODE DESCRIPTION 1 Transmitting mode Note: 1. Only the data of the worst case recorded in the test report. 2. For Radiated Emission, 3axis were chosen for testing for each applicable mode. 2.3 DESCRIPTION OF TEST SETUP Operation of EUT during Radiation: EUT

Page 7 of 24 Report No.: HK1809271172E 2.4 MEASUREMENT INSTRUMENTS LIST Cal. Item Equipment Manufacturer Model No. Serial No. Last Cal. Interval 1. Spectrum analyzer R&S FSP40 HKE-025 Dec. 28, 2017 1 Year 2. Spectrum analyzer Agilent N9020A HKE-048 Dec. 28, 2017 1 Year 3. Preamplifier Schwarzbeck BBV 9743 HKE-006 Dec. 28, 2017 1 Year 4. EMI Test Receiver Rohde & Schwarz ESCI 7 HKE-010 Dec. 28, 2017 1 Year Bilog Broadband 5. Schwarzbeck VULB9163 HKE-012 Dec. 28, 2017 1 Year Antenna FMZB 1519 6. Loop Antenna Schwarzbeck HKE-014 FMZB 1519 Dec.012 28, 2017 May 11,12016 Year 1 Year B EMI Test Software JS1120-B 7. Tonscend HKE-083 Dec. 28, 2017 N/A EZ-EMC Version 8. Shielded room Shiel Hong 4*3*3 HKE-039 Dec. 28, 2017 3 Year

Page 8 of 24 Report No.: HK1809271172E 3. RADIATED EMISSION 3.1. MEASUREMENT PROCEDURE 1. The EUT was placed on the top of the turntable 0.8 or 1.5 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. For emissions above 1GHz, use 1MHz VBW and RBW for peak reading. Then 1MHz RBW and 10Hz VBW for average reading in spectrum analyzer. Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. 7. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum values. 8.If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz. 9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that means the emissions level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. 10. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High - Low scan is not required in this case.

Page 9 of 24 Report No.: HK1809271172E The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RBW 200H2z for QP Start ~Stop Frequency 150KHz~30MHz/RBW 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RBW 120KHz for QP Receiver Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RBW 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RBW 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RBW 120KHz for QP Test limit for Standard FCC15.235 The field strength of any emission within this band shall not exceed 10,000 microvolts/meter at 3 meters. The emission limit in this paragraph is based on measurement instrumentation employing an average detector. The field strength of any emissions appearing between the band edges and up to 10 kHz above and below the band edges shall be attenuated at least 26 dB below the level of the unmodulated carrier or to the general limits in §15.209, whichever permits the higher emission levels. The field strength of any emissions removed by more than 10 kHz from the band edges shall not exceed the general radiated emission limits in §15.209. Test limit for Standard FCC 15.209 Frequency Distance Field Strengths Limit (MHz) Meters 1 V/m dB(pV)/m 0.009 ~ 0.490 300 2400/F(kHz) 0.490 ~ 1.705 30 24000/F(kHz) 1.705 ~ 30 30 30 30 ~ 88 3 100 40.0 88 ~ 216 3 150 43.5 216 ~ 960 3 200 46.0 960 ~ 1000 3 500 54.0 Above 1000 3 Other:74.0 dB(uV)/m (Peak) 54.0 dB(uV)/im (Average) Remark: (1) Emission level dBu V =20 log Emission level u V/m (2) The smaller limit shall apply at the cross point between two frequency bands. (3) Distance is the distance in meters between the measuring instrument, antenna and the closest point of any part of the device or system.

Page 10 of 24 Report No.: HK1809271172E 3.2. TEST SETUP Radiated Emission Test-Setup Frequency Below 30MHz RADIATED EMISSION TEST SETUP 30MHz-1000MHz

wA %} Page 11 of 24 Report No.: HK1809271172E 3.3. TEST RESULT RADIATED EMISSION BELOW 30MHz No emission found between lowest internal used/generated frequencies to 30MHz. RADIATED EMISSION BELOW 1GHZ—Horizontal 76.9 dBu¥/m Limit: Margin: 37 —3 30.000 127.00 224.00 321.00 418.00 515.00 612.00 709.00 B06.00 1000.00 MHz No. Mk Freq. |Reading| Factor |Measurement| Limit Over Detector AG:;;:? DE;I;LEE Comment ~ MHz dBuV dB/m dBu¥/im dBuVim dB cm degree 1 * 49.6800 58.68 11.28 69.96 80.00 |—10.04] peak 2 99.5167 24.03 10.00 34.03 43.50 —9.47 peak 3 130.2332 12.54 10.64 23.18 43.50 |—20.32) peak 4 4551832 212 20.65 2277 46.00 |—23.23) peak 5 7591167 0.77 26.76 27 .53 46.00 |—18.47) peak 6 951.5000 —0.31 29.99 29.68 46.00 |—16.32) peak

s > 4 Es P Page 12 of 24 Report No.: HK1809271172E BAND EDGE EMISSION—Horizontal 76.9 dBu¥/m Limit: — 3 Margin: — 3f 1 & \4 5 /r/ ‘\ —3 49.760 49.78 49.80 49.82 4981 49.86 49.88 49.90 49.92 49.96 MHz imni [Antennal Table No_M‘ Freq. |Reading| Factor |Measurement| Limit Over Height D MHz dBuv dBim dBuVim dBuVim dB om degree 1 49.9100 2118 11.25 3243 40.00 —7.57 peak 2 1 49.8200 2330 11.25 34.55 4338 |—8.83| peak 3 * 49.8600 5813 11.25 69.38 peak 4 1 49.9000 24.02 11.25 35.27 43.38 |—8.11| peak 5 49.9100 2218 11.25 3343 40.00 |—6.57 peak

h s Es Page 13 of 24 Report No.: HK1809271172E RADIATED EMISSION BELOW 1GHZ—Vertical 86.9 dBu¥/m Limit: — Margin: — 1 47 I—I a 6 '_3_| $ # fort" 2 6.9 30.000 127.00 224.00 321.00 418.00 515.00 612.00 709.00 806.00 1000.00 MHz jJn Frea. |Reading] Factor |Measurement] Limit Over m@:‘#m Comment ~ MHz dBuV dBim dBu¥im dBuVim d8 om degree 1| *| 4g6300 521 s2s T349 |80.00 651| peak 2 sesier 2118 269 1849 |4350|—25.01| peak 3 1253833 2611 910 3521 |43.50|—8.29| pesk a e928333 1134 25.00 3534 |46.00|—2.66| peak 5 Teaseer 1044 27.09 3753 |46.00| —8.47| peak 6 1| maas» 1115 2905 4020 |46.00|—5.80| peak

> 4 Es P %} Page 14 of 24 Report No.: HK1809271172E BAND EDGE EMISSION—Vertical 85.9 dBu¥/m Limit: — Margin: — 3 46 4 2 4 5 5.9 49.760 49.78 49.90 49.92 49.0¢ 49.86 49.99 49.90 49.92 19.96 MHz : d Antennal Table Freq. Reading] Factor |Measurement| Limit Over C No.| MK 4 9 Detector |_Height Degree Comment ~ MHz dBuv dB/m dBuVim dBu¥/im 48 cm degree 1 I 49.8100 30.47 8.25 38.72 40.00 |—1.28 peak 2 X 49.8200 3249 8.25 40.74 4716 |—6.42| peak 3 * 49.8600 64.91 8.25 7316 peak 4 X 49.9000 32.77 8.25 41.02 47.16 |—6.14 peak 5 1 49.9100 30.57 8.25 38.82 40.00 |—1.18| peak RESULT: PASS Note: 1. Factor=Antenna Factor + Cable loss — Amplifier gain, Margin=Measurement—Limit. 2. The "Factor" value can be calculated automatically by software of measurement system.

Page 15 of 24 Report No.: HK1809271172E 4. BANDWIDTH 4.1. MEASUREMENT PROCEDURE 1. Set the parameters of SPA as below: Centre frequency = Operation Frequency RBW=3KHz VBW=10KHz Span: 60kHz Sweep time: Auto 2. Set the EUT to continue transmitting mode. Allow the trace to stabilize. Use the “N dB down” function of SPA to define the bandwidth. 3. Record the plots and Reported. 4.2. TEST SETUP

Page 16 of 24 Report No.: HK1809271172E 4.3. TEST RESULT TEST ITEM 20DB BANDWIDTH TEST MODULATION AM Test Data (kHz) Criteria Operate Channel 15.64 PASS TEST PLOT OF BANDWIDTH

Page 17 of 24 Report No.: HK1809271172E 5. PHOTOGRAPH OF TEST Radiated Emission

Page 18 of 24 Report No.: HK1809271172E 6. PHOTOGRAPH OF EUT ALL VEIW OF EUT

Page 19 of 24 Report No.: HK1809271172E

Page 20 of 24 Report No.: HK1809271172E TOP VIEW OF EUT BOTTOM VIEW OF EUT

Page 21 of 24 Report No.: HK1809271172E FRONT VIEW OF EUT Antenna BACK VIEW OF EUT

Page 22 of 24 Report No.: HK1809271172E LEFT VIEW OF EUT RIGHT VIEW OF EUT

Page 23 of 24 Report No.: HK1809271172E OPEN VIEW OF EUT INTERNAL VIEW OF EUT-1

Page 24 of 24 Report No.: HK1809271172E INTERNAL VIEW OF EUT-2 ----END OF REPORT----


Document Created: 2019-07-13 01:46:16
Document Modified: 2019-07-13 01:46:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC