Attachment RadHaz

This document pretains to SES-LIC-20140507-00338 for License on a Satellite Earth Station filing.

IBFS_SESLIC2014050700338_1045171

Radiation Hazard Report Analysis of Non—lonizing Radiation for a 3.7—Meter Earth Station System This report analyzes the non—ionizing radiation levels for a 3.7—meter earth station system. The analysis and calculations performed in this report comply with the methods described in the FCC Office of Engineering and Technology Bulletin, No. 65 first published in 1985 and revised in 1997 in Edition 97—01. The radiation safety limits used in the analysis are in conformance with the FCC R&O 96—326. Bulletin No. 65 and the FCC R&O specifies that there are two separate tiers of exposure limits that are dependant on the situation in which the exposure takes place and/or the status of the individuals who are subject to the exposure. The Maximum Permissible Exposure (MPE) limits for persons in a General Population/Uncontrolled environment are shown in Table 1. The General Population/Uncontrolled MPE is a function of transmit frequency and is for an exposure period of thirty minutes or less. The MPE limits for persons in an Occupational/Controlled environment are shown in Table 2. The Occupational MPE is a function of transmit frequency and is for an exposure period of six minutes or less. The purpose of the analysis described in this report is to determine the power flux density levels of the earth station in the far—field, near—field, transition region, between the subreflector or feed and main reflector surface, at the main reflector surface, and between the antenna edge and the ground and to compare these levels to the specified MPEs. Table 1. Limits for General Population/Uncontrolled Exposure (MPE) Frequency Range (MHz) Power Density (mWicm*) 30—300 0.2 300—1500 Frequency (MHz)*(0.8/1200) 1500—100,000 1.0 Table 2. Limits for Occupational/Controlled Exbosure (MPE) Frequency Range (MHz) Power Density (mW/cm*) 30—300 1.0 300—1500 Frequency (MHz)*(4.0/1200) 1500—100,000 5.0 Table 3. Formulas and Parameters Used for Determining Power Flux Densities Parameter Symbol Formula Value Units Antenna Diameter D Input 3.7 m Antenna Surface Area Asurface 1 D/ 4 10.75 m* Feed Flange Diameter D; Input 19.0 cm Area of Feed Flange Afa x Di 44 283.53 cm* Frequency F Input 14250 MHz Wavelength A 300 /F 0.021053 m Transmit Power P Input 400.00 W Antenna Gain (dBi) Geg Input 52.8 dBi Antenna Gain (factor) G 10%°""° 190546.1 n/a Pi fo Constant 3.1415927 n/a Antenna Efficiency m 6rM/(RCD) 0.63 n/a

Radiation Hazard Report 1. Far Field Distance Calculation The distance to the beginning of the far field can be determined from the following equation: Distance to the Far Field Region R; = 0.60 D/ a (1) = 390.2 m The maximum main beam power density in the far field can be determined from the following equation: On—Axis Power Density in the Far Field Se =GP/(4 1 Ry") (2) = 39.843 W/im* = 3.984 mW/cm* 2. Near Field Calculation Power flux density is considered to be at a maximum value throughout the entire length of the defined Near Field region. The region is contained within a cylindrical volume having the same diameter as the antenna. Past the boundary of the Near Field region, the power density from the antenna decreases linearly with respect to increasing distance. The distance to the end of the Near Fisld can be determined from thé following equation: Extent of the Near Field Ry = D/ (4 2) (3) = 162.6 m The maximum power density in the Near Field can be determined from the following equation: Near Field Power Density Sn = 16.0 1 P / (1 D) (4) = 93.011 W/im* = 9.301 mW/cm* 3. Transition Region Calculation The Transition region is located between the Near and Far Field regions. The power density begins to decrease linearly with increasing distance in the Transition region. While the power density decreases inversely with distance in the Transition region, the power density decreases inversely with the square of the distance in the Far Field region. The maximum power density in the Transition region will not exceed that calculated for the Near Field region. The power density calculated in Section 1 is the highest power density the antenna can produce in any of the regions away from the antenna. The power density at a distance R, can be determined from the following equation: Transition Region Power Density S = SiRu/R (5) = 9.301 mW/icm*

Radiation Hazard Report 4. Region between the Feed Assembly and the Antenna Reflector Transmissions from the feed assembly are directed toward the antenna reflector surface, and are confined within a conical shape defined by the type of feed assembly. The most common feed assemblies are waveguide flanges, horns or subreflectors. The energy between the feed assembly and reflector surface can be calculated by determining the power density at the feed assembly surface. This can be determined from the following equation: Power Density at the Feed Flange S;a = 4000 P / Ap (6) = 5643.167 mW/cm* 5. Main Reflector Region The power density in the main reflector is determined in the same manner as the power density at the feed assembly. The area is now the area of the reflector aperture and can be determined from the following equation: Power Density at the Reflector Surface Ssurtace Z 4 P / Asurface (7) = 148.808 W/m* = 14.881 mW/cm* 6. Region between the Reflector and the Ground Assuming uniform ilumination of the reflector surface, the power density between the antenna and the ground can be determined from the following equation: Power Density between Reflector and Ground Sy =P / Asurtace (8) = 37.202 W/im* = 3.720 mW/icm*

Radiation Hazard Report 7. Summary of Calculations Table 4. Summary of Expected Radiation levels for Uncontrolled Environment Calculated Maximum Radiation Power Density Level Region {mWicm") Hazard Assessment 1. Far Field (R, = 390.2 m) Sg 3.984 Potential Hazard 2. Near Field (R,; = 162.6 m) Sn 9.301 Potential Hazard 3. Transition Region (Ry < R, < Ry) S; 9.301 Potential Hazard 4. Between Feed Assembly and Sn 5643.167 Potential Hazard Antenna Reflector 5. Main Reflector Ssurtace __14.881 Potential Hazard 6. Between Reflector and Ground Sp 3.720 Potential Hazard Table 5. Summary of Expected Radiation levels for Controlled Environment Calculated Maximum Radiation Power Density Region Level (mW/cm*) Hazard Assessment 1. Far Field (R, = 390.2 m) Sg 3.984 Satisfies FCC MPE 2. Near Field (R,; = 162.6 m) Sn 9.301 Potential Hazard 3. Transition Region (Ry < R< Rj) S; 9.301 Potential Hazard 4. Between Feed Assembly and Sta 5643.167 Potential Hazard Antenna Reflector ' 5. Main Reflector Ssurface 14.881 Potential Hazard 6. Between Reflector and Ground Sp 3.720 Satisfies FCC MPE it is the applicant‘s responsibility to ensure that the public and operational personnel are not exposed to harmful levels of radiation. 8. Conclusions Based on the above analysis it is concluded that the FCC MPE guidelines have been exceeded (or met) in the regions of Table 4 and 5. The applicant proposes to comply with the MPE limits by one or more of the following methods. Means of Compliance Uncontrolled Areas The antenna will be located on top of a truck. The bottom lip of the dish will be 3.30 meters above ground level. The general public will not have access to areas within % diameter from the edge of the antenna. Since one diameter removed from the main beam of the antenna or 4 diameter removed from the edge of the antenna the RF levels are reduced by a factor of 100 or 20 dB. None of the areas exceeding the MPE levels will be accessible by the general public.

Radiation Hazard Report Radiation hazard signs will be posted while this earth station is in operation. The applicant will ensure that no buildings or other obstacles will be in the areas that exceed the MPE levels. Means of Compliance Controlled Areas The earth station‘s operational personnel will not have access to the areas that exceed the MPE levels while the earth station is in operation. The transmitters will be turned off during antenna maintenance.

Radiation Hazard Report Page 1 of 5 Analysis of Non—lonizing Radiation for a 3.7—Meter Earth Station System This report analyzes the non—ionizing radiation levels for a 3.7—meter earth station system. The analysis and calculations performed in this report comply with the methods described in the FCC Office of Engineering and Technology Bulletin, No. 65 first published in 1985 and revised in 1997 in Edition 97—01. The radiation safety limits used in the analysis are in conformance with the FCC R&O 96—326. Bulletin No. 65 and the FCC R&O specifies that there are two separate tiers of exposure limits that are dependant on the situation in which the exposure takes place and/or the status of the individuals who are subject to the exposure. The Maximum Permissible Exposure (MPE) limits for persons in a General Population/Uncontrolled environment are shown in Table 1. The General Population/Uncontrolled MPE is a function of transmit frequency and is for an exposure period of thirty minutes or less. The MPE limits for persons in an Occupational/Controlled environment are shown in Table 2. The Occupational MPE is a function of transmit frequency and is for an exposure period of six minutes or less. The purpose of the analysis described in this report is to determine the power flux density levels of the earth station in the far—field, near—field, transition region, between the subreflector or feed and main reflector surface, at the main reflector surface, and between the antenna edge and the ground and to compare these levels to the specified MPEs. Table 1. Limits for General Population/Uncontrolied Exposure (MPE) Frequency Range (MHz) Power Density (mWicm") 30—300 0.2 300—1500 Frequency (MHz)*(0.8/1200) 1500—100,000 1.0 Table 2. Limits for Occupational/Controlled Expdsure (MPE) Frequency Range (MHz) __Power Density ({mW/cm") 30—300 1.0 300—1500 Frequency (MHz)*(4.0/1200) 1500—100,000 5.0 Table 3. Formulas and Parameters Used for Determining Power Flux Densities Parameter Symbol Formula Value Units Antenna Diameter D Input 3.7 m Antenna Surface Area Asurface x D/ 4 10.75 m Feed Flange Diameter D Input 19.0 cm Area of Feed Flange Afo x D; 4 283.53 cm* Frequency F Input 6175 MHz Wavelength A 300 /F 0.048583 m Transmit Power P Input 400.00 W Antenna Gain (dBi) Ges Input 45.6 dBi Antenna Gain (factor) 6 10%°"C 36307.8 n/a Pi T Constant 3.1415927 n/a Antenna Efficiency n 6rI(R@CD) 0.63 n/a

Radiation Hazard Report Page 2 of 5 1. Far Field Distance Calculation The distance to the beginning of the far field can be determined from the following equation: Distance to the Far Field Region Rg = 0.60 D@/a (1) = 169.1 m The maximum main beam power density in the far field can be determined from the following equation: On—Axis Power Density in the Far Field Se; =GP/(4 1 Re°) (2) = 40.431 W/m* = 4.043 mW/cm* 2. Near Field Calculation Power flux density is considered to be at a maximum value throughout the entire length of the defined Near Field region. The region is contained within a cylindrical volume having the same diameter as the antenna. Past the boundary of the Near Field region, the power density from the antenna decreases linearly with respect to increasing distance. The distance to the end of the Near Field can be determined from the following equation: Extent of the Near Field Ry = D/ (4 A) (3) = 70.4 m The maximum power density in the Near Field can be determined from the following equation: Near Field Power Density Sar = 16.0 1 P / (1 D) (4) = 94.383 W/im" = 9.438 mW/cm* 3. Transition Region Calculation The Transition region is located between the Near and Far Field regions. The power density begins to decrease linearly with increasing distance in the Transition region. While the power density decreases inversely with distance in the Transition region, the power density decreases inversely with the square of the distance in the Far Field region. The maximum power density in the Transition region will not exceed that calculated for the Near Field region. The power density calculated in Section 1 is the highest power density the antenna can produce in any of the regions away from the antenna. The power density at a distance R, can be determined from the following equation: Transition Region Power Density S =Sr Ru/R (5) = 9.438 mW/cm*

Radiation Hazard Report Page 3 of 5 4. Region between the Feed Assembly and the Antenna Reflector Transmissions from the feed assembly are directed toward the antenna reflector surface, and are confined within a conical shape defined by the type of feed assembly. The most common feed assemblies are waveguide flanges, horns or subreflectors. The energy between the feed assembly and reflector surface can be calculated by determining the power density at the feed assembly surface. This can be determined from the following equation: Power Density at the Feed Flange S = 4000 P / Aj (6) = 5643.167 mW/cm* 5. Main Reflector Region The power density in the main reflector is determined in the same manner as the power density at the feed assembly. The area is now the area of the reflector aperture and can be determined from the following equation: Power Density at the Reflector Surface Ssurtace Z4 P / Asurtace (7) = 148.808 W/im* = 14.881 mW/cm" 6. Region between the Reflector and the Ground Assuming uniform illumination of the reflector surface, the power density between the antenna and the ground can be determined from the following equation: Power Density between Reflector and Ground Sy =P / Agurface (8) = 37.202 W/im* = 3.720 mW/cm*

Radiation Hazard Report Page 4 of 5 7. Summary of Calculations Table 4. Summary of Expected Radiation levels for Uncontrolled Environment Calculated Maximum Radiation Power Density Level Region ({mWicm*) Hazard Assessment 1. Far Field (R; = 169.1 m) S¢ 4.043 Potential Hazard 2. Near Field (R,, = 70.4 m) Sn 9.438 Potential Hazard 3. Transition Region (R,; < R, < Ry) S; 9.438 Potential Hazard 4. Between Feed Assembly and S 5643.167 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface __14.881 Potential Hazard 6. Between Reflector and Ground S 3.720 Potential Hazard Table 5. Summary of Expected Radiation levels for Controlled Environment Calculated Maximum Radiation Power Density Region Level (mW/icm?*) Hazard Assessment 1. Far Field (R, = 169.1 m) S¢ 4.043 Satisfies FCC MPE 2. Near Field (R,; = 70.4 m) Snr 9.438 Potential Hazard 3. Transition Region (R;; < R, < Ry) St 9.438 Potential Hazard 4. Between Feed Assembly and Sra 5643.167 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface 14.881 Potential Hazard 6. Between Reflector and Ground Sq 3.720 Satisfies FCC MPE it is the applicant‘s responsibility to ensure that the public and operational personnel are not exposed to harmful levels of radiation. 8. Conclusions Based on the above analysis it is concluded that the FCC MPE guidelines have been exceeded (or met) in the regions of Table 4 and 5. The applicant proposes to comply with the MPE limits by one or more of the following methods. Means of Compliance Uncontrolled Areas The antenna will be located on top of a truck. The bottom lip of the dish will be 3.30 meters above ground level. The general public will not have access to areas within 14 diameter from the edge of the antenna. Since one diameter removed from the main beam of the antenna or !% diameter removed from the edge of the antenna the RF levels are reduced by a factor of 100 or 20 dB. None of the areas exceeding the MPE levels will be accessible by the general public.

Radiation Hazard Report Page 5 of 5 Radiation hazard signs will be posted while this earth station is in operation. The applicant will ensure that no buildings or other obstacles will be in the areas that exceed the MPE levels. Means of Compliance Controlied Areas The earth station‘s operational personnel will not have access to the areas that exceed the MPE levels while the earth station is in operation. The transmitters will be turned off during antenna maintenance.


Document Created: 2014-05-07 09:47:37
Document Modified: 2014-05-07 09:47:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC