Users Manual

FCC ID: ZZH-ZW1P

Users Manual

Download: PDF
FCCID_1544912

INSTALLATION INSTRUCTIONS ZW1P INSTALLATION Manual Control Wireless Lighting Control 1. Plug the ZW1P Lamp Dimming Module into a 120VAC,60HZ outlet. The Front Panel Program Button on the ZW1P dimming module allows the Plug-in Lamp 2. Plug the lamp into the ZW1P Lamp Dimming Module. Make sure the user to: lamp to be controlled does not exceed 300 Watts.(Not for use with Dimming Module fluorescent lights, motor loads, or magnetic or electronic transformers.) 1.To manually turn ON the ZW1P Lamp Dimming Module, press and release the program button.The blue indicator LED will turn ON, and the lamp plugged 3. Turn the knob or switch on the lamp to the ON position. into the ZW1P Lamp Dimming Module will also turn ON. 2.To manually turn OFF the ZW1P Lamp Dimming Module, simply press and 2 3 release the program button. The blue indicator will turn OFF and the lamp 1 plugged into the ZW1P Lamp Dimming Module will also turn OFF. 3.To manually dim the ZW1P Lamp Dimming Module, press and hold the  SPECIFICATIONS program button until the desired lighting level has been reached. 4. Refer to the instruction for your primary controller to access the setup Voltage................................................................................ 120VAC, 60Hz function and include or exclude devices. Maximum Load requirements: Incandescent......................................................................................300W ADVANCED OPERATION Resistive...........................................................................................1800W Frequency................................................................................ 908.42 MHz The following Advanced Operation parameters require that you have an Operating Temperature............................................................... 32-104° F advanced controller. However, basic remotes do not have this capability. Range.................................................................Up to 100 feet line of sight between the Wireless Controller and the closest Z-Wave receiver module. All On/All Off Depending upon your primary controller, the ZW1P dimming module can  FEATURES be set to respond to ALL ON and ALL OFF commands in up to four different ways. Some controllers may not be able to change the response from its Z-Wave controled AC outlet Provides manual and remote control default setting. Please refer to your controller’s instructions for information Blue LED show feedback from the controller on whether or not it supports the configuration function and if so, how to Ease of installation(no new wiring) change this setting. Compatible with other Z-Wave enabled devices The four possible responses are:  DESCRIPTION - It will respond to ALL-ON and the ALL-OFF command (default). - It will not respond to ALL-ON or ALL-OFF commands. This lamp dimming module is a Z-Wave enabled device and is fully comp- - It will respond to the ALL-OFF command but will not respond to the ALL-ON  OPERATIONS -atible with any Z-Wave enabled network. Z-Wave enabled devices display- command. -ing the Z-Wave logo can also be used with it regardless of the manufacturer. - It will respond to the ALL-ON command but will not respond to the ALL-OFF In a Z-Wave network, each device is designed to act as a wireless repeater. Program Button command Repeaters will retransmit the RF signal from one device to another until the intended device is reached. This ensures that the signal is received by its intended destination by routing the signal around obstacles and radio dead  WIRELESS RANGE spots. Z-Wave outlet This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 65 feet. Actual performance in a home depends WARNINGS AND CAUTIONS on the numbers of walls between the remote controller and the destination Blue LED indicator device, the type of construction and the number of Z-Wave enabled devices To be installed and/or used in accordance with approprite electrical codes installed in the control network. and regulations. Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different Things to consider regarding RF range: Basic Operation room than the controlled appliance, also an unintentional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may - Each wall or obstacle (i.e.:refrigerator, big screen TV, etc.)between the The connected light can be turned ON in two ways: remote or a Z-Wave device and the destination device will reduce the automatically be powered on due to timed event programming.Depending 1. With a Z-wave remote. maximum range by approximately 25-30%. upon the appliance, these unattended or unintentional operation could 2. Manually with the program button on the Z-Wave module. - Brick, tile or concrete walls block more of the RF signal than walls made possibly result in a hazardous condition. of wooden studs and plasterboard (drywall). Remote Control If you are unsure or uncomfortable about performing the installation, - Wall mounted Z-Wave devices installed in metal junction boxes will suffer Z-Wave remotes provide control of an Individual device, Groups of devices please consult a qualified electrician. and Scenes. Please refer to your remote control's instructions for detail on a significant loss of range (approximately 20%) since the metal box blocks its capabilities and instructions for adding and controlling devices. a large part of the RF signal. -01- -02- -03-

INSTALLATION INSTRUCTIONS Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices. Note: The distances shown in the table below are typical examples.Actual performance in your home will vary . From the Remote (or repeating Z-Wave module) to destination device: Type of Wood Frame with Brick, Tile or Construction Drywall Concrete Plastic Metal Plastic Metal J-Boxes* J-Boxes J-Boxes* J-Boxes Number of 0** 100’ 80’ 100’ 80’ Walls or 1 70’ 56’ 60’ 48’ Obstacles 2 49’ 39’ 36’ 29’ 3 34’ 27’ 21’ 17’ Restoring Factory Defaults All Configuration Parameters can all be restored to their factory default settings by using your primary controller to reset the device. Troubleshooting:Verify that the lamp wattage does not exceed the 300W rating if the module doesn’t seem to work properly. Normal operation can be restored by remote when the load is reduced to the proper rating. Over-Current Protection Additional over-current protection is provided by an internal fuse which is not user serviceable. Check your home’s circuit breakers before concluding that the product must be replaced.  WARRANTY INFORMATION Our company warranties its products to be free of defects in materials and workmanship for a period of two (2) years. There are no obligations or liabilities on the part of our company for consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation or reinstallation. Jun,2011 -04- -05-

FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC ID: ZZH-ZW1P NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.


Document Created: 2011-09-15 14:18:24
Document Modified: 2011-09-15 14:18:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC