Transmit Simultaneous Report

FCC ID: ZSH-C3310

Test Report

Download: PDF
FCCID_4063756

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 Transmit Simultaneously Report 1. Product Information Name of EUT Feature phone Model Number C3310 Model Declaration / Test Model / Modulation Type GMSK for GSM/GPRS 0.5dBi(max.) For GSM 850, Antenna Gain 0.7dBi(max.) For GSM 1900; 1.5dBi (max.) for BT Hardware version V1.1 Software version V2.01 GSM/EDGE/GPRS Operation GSM850/PCS1900/GPRS850/GPRS1900 Frequency Band UMTS Operation Frequency Band Not Supported LTE Operation Frequency Band Not Supported GSM/EDGE/GPRS Supported GSM/GPRS GSM Release Version R99 GSM/EDGE/GPRS Power Class GSM850:Power Class 4/ PCS1900:Power Class 1 GPRS/EDGE Multislot Class GPRS: Multi-slot Class 12 GPRS operation mode Class B WCDMA Release Version Not Supported HSDPA Release Version Not Supported HSUPA Release Version Not Supported DC-HSUPA Release Version Not Supported LTE Release Version Not Supported LTE/UMTS Power Class Not Supported WLAN FCC Modulation Type Not Supported WLAN FCC Operation frequency Not Supported Antenna Type Integral Antenna BT Modulation Type GFSK, π/4-DQPSK, 8-DPSK (BT V2.1+EDR) Extreme temp. Tolerance -25°C to +75°C GPS function Not Supported FM function Support and only RX NFC Function Not Supported Extreme vol. Limits 3.33VDC to 4.07VDC (Normal: 3.7VDC) This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 2. Summary of Test Results Applied Standard: FCC Part 15 Subpart C FCC Rules Description of Test Result §15.209 Radiated Emissions Compliant 3. Description of Test Modes The EUT works in the X-axis, Y-axis, Z-axis. The following operating modes were applied for the related test items. All test modes were tested, only the result of the worst case was recorded in the report. Transmit Simultaneously For Radiated Emission Test Mode Mode 1 BT+GPRS 850 Mode 2 BT+GPRS1900 4. Summary of Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Next Cal. 1 MXA Signal Analyzer Agilent N9020A MY49100040 2018-06-16 2019-06-15 SPECTRUM 2 R&S FSP 100503 2018-06-16 2019-06-15 ANALYZER 3m Semi Anechoic SIDT 3 SAC-3M 03CH03-HY 2018-06-16 2019-06-15 Chamber FRANKONIA 4 Positioning Controller MF MF-7082 / 2018-06-16 2019-06-15 5 EMI Test Software AUDIX E3 N/A 2018-06-16 2019-06-15 6 EMI Test Receiver R&S ESR 7 101181 2018-06-16 2019-06-15 7 AMPLIFIER QuieTek QTK-A2525G CHM10809065 2017-11-17 2018-11-16 8 Active Loop Antenna SCHWARZBECK FMZB 1519B 00005 2018-06-22 2019-06-21 9 By-log Antenna SCHWARZBECK VULB9163 9163-470 2018-05-01 2019-04-30 10 Horn Antenna EMCO 3115 6741 2018-06-22 2019-06-21 Broadband Horn 11 SCHWARZBECK BBHA 9170 791 2017-09-21 2018-09-20 Antenna Broadband 12 SCHWARZBECK BBV 9719 9719-025 2017-09-21 2018-09-20 Preamplifier 13 RF Cable-R03m Jye Bao RG142 CB021 2018-06-16 2019-06-15 14 RF Cable-HIGH SUHNER SUCOFLEX 106 03CH03-HY 2018-06-16 2019-06-15 Note: All equipment is calibrated through GUANGZHOU LISAI CALIBRATION AND TEST CO.,LTD. 4.1. Statement of the Measurement Uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. To CISPR 16 – 4 “Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements” and is documented in the LCS quality system acc. To DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 4.2. Measurement Uncertainty Test Item Frequency Range Uncertainty Note 9KHz~30MHz 3.10dB (1) 30MHz~200MHz 2.96dB (1) Radiation Uncertainty : 200MHz~1000MHz 3.10dB (1) 1GHz~26.5GHz 3.80dB (1) 26.5GHz~40GHz 3.90dB (1) (1). This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 5. Radiated Emissions Measurement 5.1. Standard Applicable 1) Sequence of testing 30 MHz to 1 GHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane. --- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 3 meter. --- The EUT was set into operation. Premeasurement: --- The turntable rotates from 0°to 315°using 45°steps. --- The antenna is polarized vertical and horizontal. --- The antenna height changes from 1 to 3 meter. --- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to find the maximum of all emissions. Final measurement: --- The final measurement will be performed with minimum the six highest peaks. --- According to the maximum antenna and turntable positions of premeasurement the software maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter. --- The final measurement will be done with QP detector with an EMI receiver. --- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement with marked maximum final measurements and the limit will be stored. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 2) Sequence of testing 1 GHz to 18 GHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used. --- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 3 meter. --- The EUT was set into operation. Premeasurement: --- The turntable rotates from 0°to 315°using 45°steps. --- The antenna is polarized vertical and horizontal. --- The antenna height scan range is 1 meter to 2.5 meter. --- At each turntable position and antenna polarization the analyzer sweeps with peak detection to find the maximum of all emissions. Final measurement: --- The final measurement will be performed with minimum the six highest peaks. --- According to the maximum antenna and turntable positions of premeasurement the software maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter. This procedure is repeated for both antenna polarizations. --- The final measurement will be done in the position (turntable, EUT-table and antenna polarization) causing the highest emissions with Peak and Average detector. --- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position, antenna polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement with marked maximum final measurements and the limit will be stored. 3) Sequence of testing above 18 GHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used. --- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 1 meter. --- The EUT was set into operation. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 5 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH—C3310 Premeasurement: ——— The antenna is moved spherical over the EUT in different polarizations of the antenna. Final measurement: ——— The final measurement will be performed at the position and antenna orientation for all detected emissions that were found during the premeasurements with Peak and Average detector. ——— The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored. 5.2. Test Setup Layout C—I] Antenna Tower | 3m 4m H— T 4++|_|_/ > co7 SPA/Receiver 1m °L 1 —L—§4 m [ I Turntable Reference Ground Plane Below 1GHz C_—_I] Antenna Tower }——p3m&1m “—{ |—Horn Antenna r w 4m EUT A T '\ i lm 1,.5m SPA/Receiver OBf T 17\/\ e—am ao! [ols) Turntable * ——— Reference Ground 1 Plane ~ " Above 1GHz Above 10 GHz shall be extrapolated to the specified distance using an extrapolation factor of 20 dB/decade form 3m to 1.5m. Distance extrapolation factor = 20 log (specific distanc [3m] / test distance [1.5m]) (dB); Limit line = specific limits (dBuV) + distance extrapolation factor [6 dBJ. 5.3. Results of Radiated Emissions Temperature / Humidity 23.6°C / 52.7% Test Engineer Tom Liu Test Voltage Nominal Voltage / / PASS. Only record the worst test result in this report. The test data please refer to following page. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 6 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 Below 1GHz (Worst case: BT+GPRS850) Vertical Horizontal ***Note: Only record the worst test result in this report. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 7 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 Above 1GHz BT+GPRS850 Pre. Cab. Freq. Reading Ant. Fac Measured Limit Margin Fac. Loss Remark Pol. MHz dBuv dB/m dBuv/m dBuv/m dB dB dB 4804.00 49.02 33.06 35.04 3.94 50.98 74 -23.02 Peak Horizontal 4804.00 42.96 33.06 35.04 3.94 44.92 54 -9.08 Average Horizontal 4882.00 54.26 33.16 35.15 3.96 56.23 74 -17.77 Peak Horizontal 4882.00 39.45 33.16 35.15 3.96 41.42 54 -12.58 Average Horizontal 4960.00 54.35 33.26 35.14 3.98 56.45 74 -17.55 Peak Horizontal 4960.00 42.44 33.26 35.14 3.98 44.54 54 -9.46 Average Horizontal 1648.40 42.52 30.42 31.01 2.12 44.05 74 -29.95 Peak Horizontal 1648.40 30.34 30.42 31.01 2.12 31.87 54 -22.13 Average Horizontal 1673.20 40.70 30.45 31.08 2.15 42.22 74 -31.78 Peak Horizontal 1673.20 32.54 30.45 31.08 2.15 34.06 54 -19.94 Average Horizontal 1697.60 46.60 30.58 31.12 2.17 48.23 74 -25.77 Peak Horizontal 1697.60 36.03 30.58 31.12 2.17 37.66 54 -16.34 Average Horizontal 4804.00 51.41 33.06 35.04 3.94 53.37 74 -20.63 Peak Vertical 4804.00 47.88 33.06 35.04 3.94 49.84 54 -4.16 Average Vertical 4882.00 58.24 33.16 35.15 3.96 60.21 74 -13.79 Peak Vertical 4882.00 41.93 33.16 35.15 3.96 43.90 54 -10.10 Average Vertical 4960.00 57.60 33.26 35.14 3.98 59.70 74 -14.30 Peak Vertical 4960.00 42.20 33.26 35.14 3.98 44.30 54 -9.70 Average Vertical 1648.40 44.85 30.42 31.01 2.12 46.38 74 -27.62 Peak Vertical 1648.40 35.84 30.42 31.01 2.12 37.37 54 -16.63 Average Vertical 1673.20 44.71 30.45 31.08 2.15 46.23 74 -27.77 Peak Vertical 1673.20 33.26 30.45 31.08 2.15 34.78 54 -19.22 Average Vertical 1697.60 45.37 30.58 31.12 2.17 47.00 74 -27.00 Peak Vertical 1697.60 31.75 30.58 31.12 2.17 33.38 54 -20.62 Average Vertical This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 8 of 9

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: ZSH-C3310 BT+GPRS1900 Pre. Cab. Freq. Reading Ant. Fac Measured Limit Margin Fac. Loss Remark Pol. MHz dBuv dB/m dBuv/m dBuv/m dB dB dB 4804.00 49.33 33.06 35.04 3.94 51.29 74 -22.71 Peak Horizontal 4804.00 42.05 33.06 35.04 3.94 44.01 54 -9.99 Average Horizontal 4882.00 56.04 33.16 35.15 3.96 58.01 74 -15.99 Peak Horizontal 4882.00 38.56 33.16 35.15 3.96 40.53 54 -13.47 Average Horizontal 4960.00 52.67 33.26 35.14 3.98 54.77 74 -19.23 Peak Horizontal 4960.00 42.87 33.26 35.14 3.98 44.97 54 -9.03 Average Horizontal 3700.40 44.76 32.14 34.12 3.53 46.31 74 -27.69 Peak Horizontal 3700.40 31.54 32.14 34.12 3.53 33.09 54 -20.91 Average Horizontal 3760.00 42.94 32.17 34.15 3.55 44.51 74 -29.49 Peak Horizontal 3760.00 32.34 32.17 34.15 3.55 33.91 54 -20.09 Average Horizontal 3819.60 46.72 32.21 34.19 3.58 48.32 74 -25.68 Peak Horizontal 3819.60 34.16 32.21 34.19 3.58 35.76 54 -18.24 Average Horizontal 4804.00 50.42 33.06 35.04 3.94 52.38 74 -21.62 Peak Vertical 4804.00 47.81 33.06 35.04 3.94 49.77 54 -4.23 Average Vertical 4882.00 58.16 33.16 35.15 3.96 60.13 74 -13.87 Peak Vertical 4882.00 41.02 33.16 35.15 3.96 42.99 54 -11.01 Average Vertical 4960.00 61.02 33.26 35.14 3.98 63.12 74 -10.88 Peak Vertical 4960.00 41.49 33.26 35.14 3.98 43.59 54 -10.41 Average Vertical 3700.40 46.91 32.14 34.12 3.53 48.46 74 -25.54 Peak Vertical 3700.40 34.64 32.14 34.12 3.53 36.19 54 -17.81 Average Vertical 3760.00 44.71 32.17 34.15 3.55 46.28 74 -27.72 Peak Vertical 3760.00 34.53 32.17 34.15 3.55 36.10 54 -17.90 Average Vertical 3819.60 43.07 32.21 34.19 3.58 44.67 74 -29.33 Peak Vertical 3819.60 31.68 32.21 34.19 3.58 33.48 54 -20.52 Average Vertical 1). Only record the worst test result in this report 2). 18~25GHz at least have 20dB margin. No recording in the test report. Revision History Revision Issue Date Revisions Revised By 000 October 26, 2018 Initial Issue Gavin Liang ----------------THE END OF REPORT--------------- This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 9 of 9


Document Created: 2018-11-02 14:31:40
Document Modified: 2018-11-02 14:31:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC