Test Report

FCC ID: ZNK3085B

Test Report

Download: PDF
FCCID_4472497

ITL Page 1 of 26 Report No.: D190920002 TEST REPORT Applicant: Fotorama (Hong Kong) Limited Address of Applicant: Room 7, 10/F., Peninsula Centre, 67 Mody Road, Tsimshatsui East Hong Kong Manutacturer: Dongguan Yi Jin Electronics Science and Technology Company Limited Address of Manufacturer: Floor 1—3, Building A, Dong Hui Industrial Park, Shi Tou Ling Industrial Estate, Wulian Village, Fenggang Town, Dongguan City, China Product name: Tap It Model: 3085 Rating(s): 2 x AA batteries Trademark: Ffi Cemad Standards: 47 CFR PART 15 Subpart C: section 15.249 FCC ID: ZNK3085B Data of Receipt: 2019—09—04 Date of Test: 2019—09—04~2019—09—19 Date of Issue: 2019—09—20 Test Result Pass* * In the configuration tested, the test item complied with the standards specified above. Authorized for issue by: Test by: 2&:/«:_4=%,fi > ?& wkfi/ (/ : Sep.20, 2019 Eleven Liang Pauler Li Project Engineer Project Engineer Date Name/Position Signature Date Name/Position Signature

ITL Page 2 of 26 Report No.: D190920002 Possible test case verdicts: test case does not apply to the test object .. : N/A test object does meet the requirement ........ : P (Pass) test object does not meet the requirement .. : F (Fail) Testing Laboratory information: Testing Laboratory Name .......... : ITL Co., LTD Address : No.8, Jinqianling Street 5, Huangjiang, Dongguan, Guangdong, China. Testing location : Same as above Tel : 0086-769-39001678 Fax : 0086-20-62824387 E-mail : itl@i-testlab.com General remarks: The test results presented in this report relate only to the object tested. The results contained in this report reflect the results for this particular model and serial number. It is the responsibility of the manufacturer to ensure that all production models meet the intent of the requirements detailed within this report. This report would be invalid test report without all the signatures of testing technician and approver. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. Note: /

ITL Page 3 of 26 Report No.: D190920002 1 Test Summary Test Test Requirement Test method Result Antenna Requirement FCC PART 15 C FCC PART 15 C PASS Section 15.203 Section 15.203 FCC PART 15 C Occupied Bandwidth ANSI C63.10:2013 PASS section 15.215 (c) FCC PART 15 C Radiated Emission section 15.249 ANSI C63.10:2013 PASS (a), (d) FCC PART 15 C Band Edges Measurement ANSI C63.10:2013 PASS section 15.249 (d) Conducted Emissions at Mains FCC PART 15 C ANSI C63.10:2013 N/A Terminals section 15.207

ITL Page 4 of 26 Report No.: D190920002 2 Contents Page TEST REPORT ....................................................................................................................................................................... 1 1 TEST SUMMARY ......................................................................................................................................................... 3 2 CONTENTS ................................................................................................................................................................... 4 3 GENERAL INFORMATION ........................................................................................................................................ 5 3.1 CLIENT INFORMATION ............................................................................................................................................ 5 3.2 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................................... 5 3.3 DETAILS OF E.U.T. ................................................................................................................................................ 5 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................................ 5 3.5 TEST LOCATION ..................................................................................................................................................... 5 3.6 DEVIATION FROM STANDARDS .............................................................................................................................. 5 3.7 ABNORMALITIES FROM STANDARD CONDITIONS.................................................................................................. 5 3.8 OTHER INFORMATION REQUESTED BY THE CUSTOMER ....................................................................................... 5 3.9 TEST FACILITY ....................................................................................................................................................... 6 3.10 MEASUREMENT UNCERTAINTY .............................................................................................................................. 6 4 INSTRUMENTS USED DURING TEST .................................................................................................................... 7 5 TEST RESULTS ........................................................................................................................................................... 8 5.1 E.U.T. TEST CONDITIONS ...................................................................................................................................... 8 5.2 ANTENNA REQUIREMENT ..................................................................................................................................... 10 5.3 OCCUPIED BANDWIDTH ....................................................................................................................................... 11 5.4 RADIATED SPURIOUS EMISSIONS ....................................................................................................................... 14 5.4.1 Harmonic and other spurious emissions ................................................................................................... 19 5.5 BAND EDGES REQUIREMENT .............................................................................................................................. 23 5.6 CONDUCTED EMISSIONS AT MAINS T ERMINALS 150 KHZ TO 30MHZ (N/A) .................................................... 26

ITL Page 5 of 26 Report No.: D190920002 3 General Information 3.1 Client Information Applicant: Fotorama (Hong Kong) Limited Address of Applicant: Room 7, 10/F., Peninsula Centre, 67 Mody Road, Tsimshatsui East Hong Kong 3.2 General Description of E.U.T. Name: Tap It Model No.: 3085 Trade Mark: Operating Frequency: 2470 MHz Type of Modulation GFSK Antenna Type: PCB antenna Antenna gain: 0.7 dBi 3.3 Details of E.U.T. EUT Power Supply: 2 x AA batteries Test mode: The program used to control the EUT for staying in continuous transmitting and receiving mode is programmed. Channel 2470MHz is chosen for full testing. Power cord: / 3.4 Description of Support Units The EUT has been tested as an independent unit for fixed frequency by testing lab. 3.5 Test Location All tests were performed at: ITL Co., Ltd. No.8, JinQianLing street 5, DongHuan Road, Huangjiang Town, Dongguan, China. 0086-769-39001678 itl@i-testlab.com No tests were sub-contracted. 3.6 Deviation from Standards Biconical and log periodic antennas were used instead of dipole antennas. 3.7 Abnormalities from Standard Conditions None. 3.8 Other Information Requested by the Customer None.

ITL Page 6 of 26 Report No.: D190920002 3.9 Test Facility The test facility is recognized, certified, or accredited by the following organizations:  CNAS( Lab code:L9342)  FCC ( Resignation No.:CN5035)  IC (Registration NO.:12593A) 3.10 Measurement Uncertainty The below measurement uncertainties given below are based on a 95% confidence level (base on a coverage factor (k=2).) Parameter Uncertainty Radio frequency ±1.06 x 10-7 total RF power, conducted 1.37 dB RF power density , conducted 2.89 dB All emissions, radiated ±3.35 dB Temperature ±0.23 °C Humidity ±0.3 % DC and low frequency voltages ±0.3 %

ITL Page 7 of 26 Report No.: D190920002 4 Instruments Used during Test No. Test Equipment Manufacturer Model Serial No. Last Cal. Cal. Due Spectrum ITL-114 Agilent N9010A MY51250936 2019/01/28 2020/01/27 Analyzer EMI test receiver ITL-154 R&S ESR26 101257 2019/01/29 2020/01/28 9kHz to 26.5GHz ITL-116 Pre Amplifier HP 8447F 3113A05905 2019/01/28 2020/01/27 Wideband ZVA-183- ITL-117 Amplifier Super Mini-circuits 469101134 2019/01/28 2020/01/27 S+ Ultra Trilog-Broadband VULB ITL-164 Schwarzbeck 9168-0844 2017/11/16 2020/11/16 Antenna 9168 JXTXLB- J2031090612 ITL-110 Horn Antenna A-INFOMW 2019/01/28 2020/01/27 10180-N 133 ITL-102 EMI Test receiver R&S ESCI 100910 2019/06/19 2020/06/18 Two-line v- ITL-103 R&S ENV216 100120 2019/06/19 2020/06/18 network 50Ω Coaxial ITL-115 Mini-circuits CBL C001 2019/06/19 2020/06/18 Cable Semi-Anechoic FACT3 ITL-100 ETS•Lindgren CT09015 2018/12/29 2021/12/28 chamber 2.0 ITL-101 Shielded Room ETS•Lindgren 8*4*3 CT09010 2018/01/27 2021/01/26 ITL-165 Power Meter R&S NRVS 838246/026 2018/09/28 2019/09/27 Active Loop FMZB ITL-163 Schwarzbeck 1519B-062 2017/11/16 2020/11/16 Antenna 1519B

ITL Page 8 of 26 Report No.: D190920002 5 Test Results 5.1 E.U.T. test conditions Test Voltage: 2 x AA batteries Temperature: 23.2 -25.0 °C Humidity: 38-50 % RH Atmospheric Pressure: 1000 -1010 mbar Requirements: 15.31(e): For intentional radiators, measurements of the variation of the input power or the radiated signal level of the fundamental frequency component of the emission, as appropriate, shall be performed with the supply voltage varied between 85% and 115% of the nominal rated supply voltage. For battery operated equipment, the equipment tests shall be performed using a new battery. 15.32: Power supplies and CPU boards used with personal computers and for which separate authorizations are required to be obtained shall be tested as follows: Testing shall be in accordance with the procedures specified in Section 15.31 of this part. Test frequencies and According to the 15.31(m) Measurements on intentional radiators or frequency range: receivers, other than TV broadcast receivers, shall be performed and, if required, reported for each band in which the device can be operated with the device operating at the number of frequencies in each band specified in the following table: According to the 15.33 (a) For an intentional radiator, the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to at least the frequency shown in the following table: Number of fundamental frequencies to be tested in EUT transmit band Frequency range in which Number of Location in frequency range 1 MHz or less 1 Middle 1 MHz 2 1 near top and 1 near bottom 1 near top, 1 near middle and 1 More than 10 MHz 3 near bottom Frequency range of radiated emission measurements Lowest frequency generated Upper frequency range of measurement 9 kHz to below 10 GHz 10th harmonic of highest fundamental frequency or to 40 GHz, At or above 10 GHz to below 5th harmonic of highest fundamental frequency or to 100 GHz, At or above 30 GHz 5th harmonic of highest fundamental frequency or to 200 GHz,

ITL Page 9 of 26 Report No.: D190920002 EUT channels and frequencies list: channel Frequency 1 2470 Test frequencies is 2470 MHz Test the EUT in continuous transmission mode, duty cycle＞98%.

ITL Page 10 of 26 Report No.: D190920002 5.2 Antenna requirement Standard requirement 15.203 requirement: For intentional device. According to 15.203. An intentional radiator shall be designed to Ensure that no antenna other than that furnished by the responsible party shall be used with the device. EUT Antenna The antenna is a PCB antenna and no consideration of replacement. The best case gain of the antenna is 0.7 dBi. Test result: The unit does meet the FCC requirements.

ITL Page 11 of 26 Report No.: D190920002 5.3 Occupied Bandwidth Test Requirement: FCC PART 15 C section 15.215(c) (c) Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §§ 15.217 through 15.257 and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rulesection under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated Test Method: ANSI C63.10:2013 Test Status: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, channels and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Test Configuration: Test Procedure: 1. Remove the antenna from the EUT and then connect a low attention attenuation RF cable (Cable loss =0.5dB) from the antenna port to the spectrum. a) The instrument center frequency was set to the nominal EUT channel center frequency. The frequency span for the spectrum analyzer was between 1.5 times and 5.0 times the OBW(20 dB Bandwidth). b) The nominal IF filter bandwidth (3 dB RBW) was in the range of 1% to 5% of the OBW, and VBW was approximately three times the RBW. c) Set the reference level of the instrument as required, keeping the signal from exceeding the maximum input mixer level for linear operation. In general, the peak of the spectral

ITL Page 12 of 26 Report No.: D190920002 envelope was more than [10 log (OBW/RBW)] below the reference level. d) Step a) through step c) might require iteration to adjust within the specified range. e) The dynamic range of the instrument at the selected RBW was more than 10 dB below the target “−20 dB down”requirement; that is, if the requirement calls for measuring the −20 dB OBW, the instrument noise floor at the selected RBW was at least 30 dB below the reference value. f) Peak detection and max hold mode (until the trace stabilizes) was used. g) Used the 20dB bandwidth function of the instrument and reported the measured bandwidth. h) The occupied bandwidth was reported by providing plot(s) of the measuring instrument display; the plot axes and the scale units per division was clearly labeled. Tabular data was reported in addition to the plot(s). 20 dB bandwidth: Frequency Measured 20dB Limit Result Channel (MHz) bandwidth No. (MHz) 2400- 1 2470 1.216 2483.5 Pass MHz

ITL Page 13 of 26 Report No.: D190920002 20dB bandwidth: Result plot as follows: Channel 1:2.470GHz:

ITL Page 14 of 26 Report No.: D190920002 5.4 Radiated Spurious Emissions Test Requirement: FCC PART 15 C section 15.249 (a), (d) (a) Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Note: The limits shown in the above table are based on measurements using an average detector, except for the fundamental emission in the frequency band 902-928 MHz, which is based on measurements using a CISPR quasi-peak detector. (d) Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in§ 15.209, whichever is the lesser attenuation. Test Method: ANSI C63.10:2013 Clause 6.4, 6.5 and 6.6 Test Status: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, channels and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Detector: For PK value: RBW = 1 MHz for f ≥ 1 GHz, 100 kHz for f < 1 GHz VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold 15.209 Limit: 40.0 dBµV/m between 30MHz & 88MHz 43.5 dBµV/m between 88MHz & 216MHz 46.0 dBµV/m between 216MHz & 960MHz 54.0 dBµV/m above 960MHz The average correction factor was computed by analyzing the on time in 100ms over one complete pulse train. Analysis of the remote transmitter on time in one complete pulse train,

ITL Page 15 of 26 Report No.: D190920002 therefore the average value of fundamental frequency was: Average = Peak value + 20log (Duty cycle), where the duty factor is calculated from following formula: The duration of one cycle =1.064ms Effective period of the cycle =0.184ms DC =0.184/1.064=0.1729 or 17.29% Therefore, the averaging factor is found by 20lg0.1729=-15.24 Please refer to below plots for more details.

ITL Page 16 of 26 Report No.: D190920002 Section 15.205 Restricted bands of operation. MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 10.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 13.36 - 13.41 322 - 335.4

ITL Page 17 of 26 Report No.: D190920002 Test Configuration: 1) 9kHz to 30MHz emissions: 2) 30 MHz to 1 GHz emissions:

ITL Page 18 of 26 Report No.: D190920002 3) 1 GHz to 40 GHz emissions: Test Procedure: 1) 9 kHz to 30 MHz emissions: For testing performed with the loop antenna. The centre of the loop was positioned 1 m above the ground and positioned with its plane vertical at the special distance from the EUT. During testing the loop was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. 2) 30 MHz to 1 GHz emissions: For testing performed with the bi-log type antenna. The measurement is performed with the EUT rotated 360o, the antenna height scanned between 1m and 4m, and the antenna rotated to repeat the measurement for both the horizontal and vertical antenna polarizations. 3) 1 GHz to 25 GHz emissions: Test site with RF absorbing material covering the ground plane that met the site validation criterion called out in CISPR 16-1-4:2010 was used to perform radiated emission test above 1 GHz. For testing performed with the horn antenna. The measurement is performed with the EUT o rotated 360 , the antenna height scanned between 1m and 4m, and the antenna rotated to repeat the measurement for both the horizontal and vertical antenna polarizations. 4) The receiver was scanned from 9 kHz to 25 GHz. When an emission was found, the table was rotated to produce the maximum signal strength. An initial pre-scan was performed for in peak detection mode using the receiver. The EUT was measured for both the Horizontal and Vertical polarities and performed a pre-test three orthogonal planes. For intentional radiators, measurements of the variation of the input power or the radiated signal level of the fundamental frequency component of the emission, as appropriate, shall be performed with the supply voltage varied between 85% and 115% of the nominal rated supply voltage. The worst case emissions were reported. Used Test Equipment List: 3m Semi-Anechoic Chamber, EMI Test Receiver (9 kHz~7 GHz), Signal and Spectrum Analyzer (10 Hz~40 GHz), Loop antenna (9 kHz-30 MHz). TRILOG Super Broadband test Antenna(30 MHz- 3 GHz）(RX), Bouble-Ridged Waveguide Horn Antenna (800 MHz-18 GHz)(RX) and High Frequency Antenna & preamplifier(18 GHz~26.5 GHz) (RX). Refer to Clause 5 Test Equipment List for details. 9 kHz~30 MHz Field Strength of Unwanted Emissions. Quasi-Peak Measurement The measurements with active loop antenna were greater than 20dB below the limit, so the test data were not recorded in the test report.

ITL Page 19 of 26 Report No.: 0190920002 5.4.1. Harmonic and other spurious emissions Test at Channel 1 (2470 GHz)in ransmiting status 9kHz~30MHz Tost result The Low frequency, which started from 9kz to SOMHz, was pre— scanned and the result which was 2008 lower than the limiline per 15.31(0) was not report 30 MHz~1 GHz Spurious Emissions .Quas+Poak Measurement Horizontal: Posk scan Lovel (dBa¥/m) so Love(dBut/im) 70 60 rcopnt 15e o9 so ao s , M M : 2o 10 So ow son. son on son. ~oon. Tou. son. a00, ons Frequency uit Ouast—peak measurement o. Ereq Read, Antema: Cable: Preanp Level Linst Over Pol/Phase Renark bekn Pator Loes Fictor the TS me ut & & ou‘s duls & I mm ine d2a Lhb mm ine on cai mmzme o 2oemse onl in dol rni onl @ado ce rewronen uP $amsm rhe 2in oZe dual qcll 200 ons fewrone & 4 bencaso delos 2o.do Sle deiss Pnes anlo cislor matiomic. ar Level~Read Level + Antenna Factor + Cable Loss = Presap Factor

ITL Page 20 of 26 Report No.: 0190920002 Vertical: Posk scan Lovel (dBavim) 80Le'vel (duim) m io s a Dute® Frequency it Ouast—peak measurement No. Freq Read Antenna Cable Presip Level Linst Over Pol/Phaze Renark mc dbut & & & dbut/n du/a & Factor

ITL Page 21 of 26 Report No.: 0190920002 Abore 1G Horizontal: Peak scan mestum so reepart 1se en zo 1 co rco pmet 15e avennce = a lut® a n T000 Toon. ooo 000. ooo t2000.— riovn.~— 10000.— toote Frequency flte) Frequency Reading Duty oycle Limit Margin Anterna ho. MERCY | "Leve Carrest Factor L®¥e! (d:) polariatio remark (wite gbuy) Bm we) (dBq¥im) (cBaim) 1 2470 51.30 ass Na ar.ee T100 601 H Poakk 452s |_saro sam A12 H ay 2 1350 is see n se m in i Peak 4s2s |_ar0s sam 1635 h ay

ITL Page 22 of 26 Report No.: 0190920002 verticats Pesk scan clevet uim so ree par 1se en 70 co tecpmet 1se avernce so w ut m w Tove Toon. sonn, sonn, oooe. z000. rioon,— tooun,— teote Frequency tiiey Frequency i Reading Duty vow cycle Limit Marginin Anterna ho. ECY Level Cartect| Factor L99! us potzrizatio remarkc (MM® apuyy (dBim) apy (CBLY) (BkVm) " 7 2 soso 12 |_Na saee Trico 908 v Poak 452 |_ss70 sam 1220 v ay 2 z90 a7rso asr |_Nna srer 7am 2273 v Poak 452 |_sena sam a7er v ay Remorc 1) JFortisintertional radletor operates below 25 GH. The spectrum shall be investigated to the tenth harmoniesof the highest fundamental frequency. And above the this harmonic ofths ntentona radiator,the cisturbance is very lew. So the test result ony clsplays to 9" hermon. 2). As shown in Section, for frequencies above 1000 Niz. the above fild strength Imts are based on average Iims. However, the geak feld strength of any emission shall not exceed the mextmum permited average Imis specifec above by more than 20 dB under any conditon of modutaton. 3). The test only perfom the EUT in ransmiting statis since the test requiencies were over 1GHz only required transmiting status. Test result The undoes meet the FCC requirements.

ITL Page 23 of 26 Report No.: D190920002 5.5 Band Edges Requirement Test Requirement: FCC Part 15 C section 15.249 (d) Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in§ 15.209, whichever is the lesser attenuation. Frequency Band: 2400 MHz to 2483.5 MHz Test Method: ANSI C63.10:2013 Test Status: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, channels and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Test Configuration: Used Test Equipment List: 3m Semi-Anechoic Chamber, EMI Test Receiver (9kHz~7 GHz), Signal and Spectrum Analyzer (10 Hz~40 GHz), Loop antenna (9 kHz-30 MHz). TRILOG Super Broadband test Antenna(30 MHz-3 GHz）(RX), Bouble-Ridged Waveguide Horn Antenna (800 MHz-18 GHz)(RX) and High Frequency Antenna & preamplifier(18 GHz~26.5 GHz) (RX). Refer to Clause 5 Test Equipment List for details.

ITL Page 24 of 26 Report No.: 0190920002 Resut pot as folows Chamel 1: 2470 GHz Honzontal sn Level ataivim so ree pmt 1se perw 70 o rec pant15 avernce so ao 1 so Nosltinapad 20 10 zro zio. zin. on 2ien 2ien. Poon. in Poid. Z5ro Frequency (itlo Mens. Frequency ReauIn [Bandwict Correct Level Limt margin Antenna purig h96 BW Tme (moy ow (doimce m | tagyivim) caguvim) m (aBuim) B0m u; (a9) Pomizate n Remak 24294 sa17 1000 1000 0.4 aa31 d Eo H Paok 2ssas saeo 1000 toso o.t0 sa0 74| 1080 H Pook

ITL Page 25 of 26 Report No.: 0190920002 vertcal oLevetidtuvim so reopart 1sc peaw 70 60 rcopart 15e averace so ao ; : so 20 10 mre zio. zim 2iin zon zon moin. Zre Frequency| Reasing Mens. qarty sevel time EBandwicth] Gogy Correct| garn Level copvim Limt cBiv margin q; Anterna Potstizato Remark @99 (ms Bm m | (Buvim)m (@Buvim) m (a8) n 24430 ss.so 1000 1000 o.13 css 74 s837 v Peak 25228 see 1000 1000 o.i8 s2.60 74 10 v Peak

ITL Page 26 of 26 Report No.: D190920002 5.6 Conducted Emissions at Mains Terminals 150 kHz to 30MHz (N/A) Test Requirement: FCC Part 15 C section 15.207 Test Method: ANSI C63.10:2013 Frequency Range: 150 kHz to 30 MHz Detector: Peak for pre-scan (9 kHz Resolution Bandwidth) Test Limit Limits for conducted disturbance at the mains ports of class B Class B Limit dB(µV) Frequency Range Quasi-peak Average 0.15 to 0.50 66 to 56 56 to 46 0.50 to 5 56 46 5 to 30 60 50 NOTE 1 The limit decreases linearly with the logarithm of the frequency in the range 0,15 MHz to 0,50 MHz. -- End of test report --


Document Created: 2019-10-09 00:13:04
Document Modified: 2019-10-09 00:13:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC