I19Z61829-SEM01_SAR_Rev0_8

FCC ID: ZNFX540HM

RF Exposure Info

Download: PDF
FCCID_4474995

No.I19Z61829-SEM01 ANNEX I Sensor Triggering Data Summary . According to the above description, this device was tested by the manufacturer to determine the SAR sensor triggering distances for the rear and bottom edge of the device. The measured power state within ±5mm of the triggering points (or until touching the phantom) is included for rear and each applicable edge. To ensure all production units are compliant it is necessary to test SAR at a distance 1mm less than the smallest distance from the device and SAR phantom with the device at maximum output power without power reduction. ©Copyright. All rights reserved by CTTL. Page 236 of 246

No.I19Z61829-SEM01 We tested the power and got the different proximity sensor triggering distances for front, rear and bottom edge. But the manufacturer has declared 2mm is the most conservative triggering distance for main antenna. So base on the most conservative triggering distance of 2mm, additional SAR measurements were required at 1mm from the highest SAR position. Front Moving device toward the phantom: The power state Distance 7 6 5 4 3 2 1 0 [mm] Main Normal Normal Normal Normal Normal Low Low Low antenna Moving device away from the phantom: The power state Distance 0 1 2 3 4 5 6 7 [mm] Main Low Low Normal Normal Low Normal Normal Normal antenna Rear Moving device toward the phantom: The power state Distance 7 6 5 4 3 2 1 0 [mm] Main Normal Normal Normal Normal Normal Low Low Low antenna Moving device away from the phantom: The power state Distance 0 1 2 3 4 5 6 7 [mm] Main Low Low Normal Normal Low Normal Normal Normal antenna Bottom Edge Moving device toward the phantom: The power state Distance 7 6 5 4 3 2 1 0 [mm] Main Normal Normal Normal Normal Normal Low Low Low antenna ©Copyright. All rights reserved by CTTL. Page 237 of 246

No.I19Z61829-SEM01 Moving device away from the phantom: The power state Distance 0 1 2 3 4 5 6 7 [mm] Main Low Low Normal Normal Low Normal Normal Normal antenna The influence of table tilt angles to proximity sensor triggering is determined by positioning each edge that contains a transmitting antenna, perpendicular to the flat phantom, at the smallest sensor triggering test distance by rotating the device around the edge next to the phantom in ≤ 10° increments until the tablet is ±45°or more from the vertical position at 0°. The Front evaluation for main antenna The rear evaluation for main antenna ©Copyright. All rights reserved by CTTL. Page 238 of 246

No.I19Z61829-SEM01 The bottom edge evaluation for main antenna Based on the above evaluation, we come to the conclusion that the sensor triggering is not released and normal maximum output power is not restored within the ±45°range at the smallest sensor triggering test distance declared by manufacturer. ©Copyright. All rights reserved by CTTL. Page 239 of 246

No.I19Z61829-SEM01 ANNEX J SPOT CHECK J.1 Dielectric Performance Table J.1-1: Dielectric Performance of Tissue Simulating Liquid Measurement Permittivity Drift Conductivity Drift Date Type Frequency ε (%) σ (S/m) (%) (yyyy-mm-dd) Head 5250 MHz 37.1 3.26 4.722 0.25 2019-10-9 Body 2600 MHz 53.3 1.52 2.195 1.62 Note: The liquid temperature is 22.0oC J.2 System Verification Table J.2-1: System Verification of Head Measurement Target value (W/kg) Measured value(W/kg) Deviation Date Frequency 1B 10 g 1g 10 g 1g 10 g 1g (yyyy-mm-dd) Average Average Average Average Average Average 2019-10-9 5250 MHz 23.1 80.8 23.4 80.2 1.30% -0.74% Table J.2-2: System Verification of Body Measurement Target value (W/kg) Measured value (W/kg) Deviation Date Frequency 2B 10 g 1g 10 g 1g 10 g 1g (yyyy-mm-dd) Average Average Average Average Average Average 2019-10-9 2600 MHz 24.8 55.0 24.4 54.0 -1.77% -1.82% J.3 Conducted power of selected case Table J.3-1: The conducted Power for LTE Band Mode Frequency (Channel) Measured Power (dBm) LTE Band 7 20MHz-1RB-Middle (50) 2560 (21350) 22.90 Table J.3-2: The conducted Power for WLAN Mode / data rate Frequency (Channel) Measured Power (dBm) 802.11a / 6Mbps 60 (5300) 12.95 ©Copyright. All rights reserved by CTTL. Page 240 of 246

No.I19Z61829-SEM01 J.4 Measurement results Tune- Conducted Measured Reported Measured Reported Power Test Figure up Test Band Channel Frequency Power SAR(10g) SAR(10g) SAR(1g) SAR(1g) Drift Position No./Note Power (dBm) (W/kg) (W/kg) (W/kg) (W/kg) (dB) (dBm) Wi-Fi 5G 60 5300 Right Fig J.6-1 12.95 14.5 0.228 0.33 0.661 0.94 0.01 LTE Band 7 21350 2560 Bottom Fig J.6-2 22.90 24 0.360 0.46 0.742 0.96 -0.11 Table J.4-1: SAR Values (WLAN - Head) – 802.11b (Scaled Reported SAR) Frequency Test Actual duty maximum Reported SAR Scaled reported Side MHz Ch. Position factor duty factor (1g) (W/kg) SAR (1g) (W/kg) 5300 60 Right Tilt 100% 100% 0.94 0.94 J.5 Reported SAR Comparison Exposure Reported SAR Reported SAR Technology Band Configuration 1g (W/kg): spot check 1g (W/kg): original GSM 850 / 0.22 PCS 1900 / 0.12 UMTS FDD 2 / 0.24 UMTS FDD 4 / 0.20 UMTS FDD 5 / 0.28 LTE Band 2 / 0.23 Head LTE Band 5 / 0.23 (Separation LTE Band 7 / 0.26 Distance 0mm) LTE Band 12 / 0.17 LTE Band13 / 0.18 LTE Band 38 / 0.14 LTE Band 66 / 0.19 WLAN 2.4 GHz / 0.74 WLAN 5GHz 0.94 0.95 GSM 850 / 0.53 PCS 1900 / 0.54 UMTS FDD 2 / 1.05 UMTS FDD 4 / 0.75 UMTS FDD 5 / 0.51 LTE Band 2 / 1.10 Hotspot LTE Band 5 / 0.52 (Separation LTE Band 7 0.96 1.27 Distance 10mm) LTE Band 12 / 0.31 LTE Band13 / 0.34 LTE Band 38 / 0.70 LTE Band 66 / 0.86 WLAN 2.4 GHz / 0.17 WLAN 5GHz / 0.23 ©Copyright. All rights reserved by CTTL. Page 241 of 246

No.I19Z61829-SEM01 J.6 Graph Results of spot check WLAN_CH60 Right Tilt Date: 10/9/2019 Electronics: DAE4 Sn771 Medium: head 5 GHz Medium parameters used: f = 5300; σ = 4.772 mho/m; εr = 37.05; ρ = 1000 kg/m3 Ambient Temperature: 22.5oC, Liquid Temperature: 22.3oC Communication System: WLAN 5300 Duty Cycle: 1:1 Probe: EX3DV4 – SN3617 ConvF(5.25, 5.25, 5.25) Area Scan (111x201x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 1.56 W/kg Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 3.674 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 2.80 W/kg SAR(1 g) = 0.661 W/kg; SAR(10 g) = 0.228 W/kg Maximum value of SAR (measured) = 1.55 W/kg Fig J.6-1 ©Copyright. All rights reserved by CTTL. Page 242 of 246

No.I19Z61829-SEM01 LTE2500-FDD7_CH21350 Bottom Date: 10/9/2019 Electronics: DAE4 Sn771 Medium: body 2600 MHz Medium parameters used: f = 2560 MHz; σ = 2.157 mho/m; εr = 53.35; ρ = 1000 kg/m3 Ambient Temperature: 22.5oC, Liquid Temperature: 22.3oC Communication System: LTE2500-FDD7 2560 MHz Duty Cycle: 1:1 Probe: EX3DV4 – SN3617 ConvF(7.49,7.49,7.49) Area Scan (131x101x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 1.17 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 15.38 V/m; Power Drift = -0.11 dB Peak SAR (extrapolated) = 1.48 W/kg SAR(1 g) = 0.742 W/kg; SAR(10 g) = 0.360 W/kg Maximum value of SAR (measured) = 1.16 W/kg Fig J.6-2 ©Copyright. All rights reserved by CTTL. Page 243 of 246

No.I19Z61829-SEM01 J.7 System Verification Results 5250 MHz Date: 10/9/2019 Electronics: DAE4 Sn771 Medium: Head 5250 MHz Medium parameters used: f = 5250 MHz; σ =4.722 mho/m; εr = 37.1; ρ = 1000 kg/m3 Ambient Temperature: 22.5oC Liquid Temperature: 22.3oC Communication System: CW Frequency: 5250 MHz Duty Cycle: 1:1 Probe: EX3DV4 – SN3617 ConvF(5.39,5.39,5.39) System Validation /Area Scan (81x191x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 17.83 W/kg System Validation /Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value =76.5 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 27.92 W/kg SAR(1 g) = 8.02 W/kg; SAR(10 g) = 2.34 W/kg Maximum value of SAR (measured) = 18.06 W/kg 0 dB = 18.06 W/kg = 12.57 dB W/kg Fig J.7-1 validation 5250 MHz 100mW ©Copyright. All rights reserved by CTTL. Page 244 of 246

No.I19Z61829-SEM01 2600 MHz Date: 10/9/2019 Electronics: DAE4 Sn771 Medium: Body 2600 MHz Medium parameters used: f = 2600 MHz; σ =2.195 mho/m; εr = 53.3; ρ = 1000 kg/m3 Ambient Temperature: 22.5oC Liquid Temperature: 22.3oC Communication System: CW Frequency: 2600 MHz Duty Cycle: 1:1 Probe: EX3DV4 – SN3617 ConvF(7.49,7.49,7.49) System Validation /Area Scan (81x191x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 23.15 W/kg System Validation /Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value =109.4 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 28.45 W/kg SAR(1 g) = 13.5 W/kg; SAR(10 g) = 6.09 W/kg Maximum value of SAR (measured) = 23.31 W/kg 0 dB = 23.31 W/kg = 13.68 dB W/kg Fig J.7-2 validation 2600 MHz 250mW ©Copyright. All rights reserved by CTTL. Page 245 of 246

No.I19Z61829-SEM01 ANNEX K Accreditation Certificate ©Copyright. All rights reserved by CTTL. Page 246 of 246


Document Created: 2019-10-10 17:15:14
Document Modified: 2019-10-10 17:15:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC