I19Z61557-SEM01_SAR_Rev0_6

FCC ID: ZNFX540EMW

RF Exposure Info

Download: PDF
FCCID_4462401

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.10.2 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz + 1 MHz 5250 MHz +1 MHz 5300 MHz + 1 MHz Frequency 5500 MHz + 1 MHz 5600 MHz + 1 MHz 5750 MHz + 1 MHz 5800 MHz + 1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.5 16 % 4.46 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.06 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.3 W/kg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.32 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.0 W/kg * 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul19 Page 3 of 23 n un en n mn n e ewne e menener e mev wn n

wo cce w on wmyy rvxe vn r ui Head TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.71 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.5 26 % 4.51 mho/m + 6 % Head TSL temperature change during test «05 °C ~—— ==— SAR result with Head TSL at 5250 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.07 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.33 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.2 Wikg * 19.5 % (k=2) Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 35.4 +6 % 4.56 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.23 W/kg SAR for nominal Head TSL parameters normalized to 1W 82.0 W/kg * 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.37 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.5 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul19 Page 4 of 23 Eo cpyeagie s ragr cez n nenever n vzne wny vee e k.

«ow se e n se ne n w nz n en an w y esns sn avk Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.1 +6 % 4.76 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.51 Wikg SAR for nominal Head TSL parameters normalized to 1W 84.7 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.43 W/kg SAR for nominal Head TSL parameters normalized to 1W 24.2 Wikg * 19.5 % (k=2) Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.0 +6 % 4.86 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.49 W/kg SAR for nominal Head TSL parameters normalized to 1W 84.5 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.43 W/kg SAR for nominal Head TSL parameters normalized to 1W 24.1 Wikg * 19.5 %(k=2) Certificate No: D5GHzV2—1060_Jul19 Page 5 of 23 t acnge en e e rrggr en e ns ner e neve weg n + n

«ow se e n se ne n w nz n en an w mg y 6k w se k vk Head TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.4 5.22 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.8 +6 % 5.02 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5750 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.08 Wikg SAR for nominal Head TSL parameters normalized to 1W 80.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.31 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.0 W/kg + 19.5 % (k=2) Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.3 5.27 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.7 26 % 5.07 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.14 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.9 W/kg * 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.30 W/kg SAR for nominal Head TSL parameters normalized to 1W 22.9 W/kg * 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul19 Page 6 of 23 t acnge en e e rrggr en e ns ner e neve weg n + n

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.3 16 % 5.43 mho/m + 6 % Body TSL temperature change during test <0.5 °C «++ SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 741 W/kg SAR for nominal Body TSL parameters normalized to 1W 73.6 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.08 W/kg SAR for nominal Body TSL parameters normalized to 1W 20.6 Wikg * 19.5 % (k=2) Body TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.36 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.2 +6 % 5.49 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5250 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.67 Wikg SAR for nominal Body TSL parameters normalized to 1W 76.2 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.15 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.3 Wikg * 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul19 Page 7 of 23

Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.1 16 % 5.56 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.52 Wi/kg SAR for nominal Body TSL parameters normalized to 1W 74.7 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.13 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.1 Wikg £ 19.5 % (k=2) Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.7 +6 % 5.83 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.00 W/kg SAR for nominal Body TSL parameters normalized to 1W 79.5 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.23 W/kg SAR for nominal Body TSL parameters normalized to 1W 22.1 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul19 Page 8 of 23 C o epegrsgme n m rngrrve n e e e e en e n es

() ~ S Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Nominal Body TSL parameters Measured Body TSL parameters Temperature 22.0 °C (22.0 + 0.2) °C Permittivity 48.5 46.6 +6 % Conductivity 5.77 mho/m 5.97 mho/m + 6 % Body TSL temperature change during test <0.5 °C «en SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.87 Wi/kg SAR for nominal Body TSL parameters normalized to 1W 78.2 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.22 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.0 Wikg # 19.5 % (k=2) Body TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.3 5.94 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.3 +6 % 6.17 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5750 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.79 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.4 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.18 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.5 Wikg * 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul19 Page 9 of 23 =ooma n n n e n n n cez snn ner n neve meg n ns

Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.2 £ 6 % 6.24 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~—— SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.51 W/kg SAR for nominal Body TSL parameters normalized to 1W 74.6 W/kg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.09 W/kg SAR for nominal Body TSL parameters normalized to 1W 20.7 Wikg + 19.5 %(k=2) Certificate No: D5GHzV2—1060_Jul19 Page 10 of 23

—mm»..__> i‘/"/‘/, ~3g— _2 _ _—_ prir Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 48.7 Q — 5.5 jQ Return Loss — 24.9 dB Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point 48.6 Q — 4.0 jQ Return Loss —27.5 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 47.7 Q — 3.3 jQ Return Loss —27.7 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 50.9 Q — 3.9 jQ Return Loss —28.2 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 54.2 Q + 0.3 jQ Return Loss —27.9 dB Antenna Parameters with Head TSL at 5750 MHz Impedance, transformed to feed point 51.7 Q — 0.8 jQ Return Loss — 34.7 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 52.1 Q — 24 jQ Return Loss — 30.1 dB Certificate No: D5GHzV2—1060_Jul19 fon un n n n e n n n e n en y e >

6 ww en n se cz n a se k un e q 6oviys ra v on yc Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 48.9 Q — 5.6 jQ Return Loss — 24.8 dB Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 48.0 Q — 2.2 jQ Return Loss — 30.4 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 48.3 Q — 3.0 jQ Return Loss —29.1 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 50.2 Q — 2.2 jQ Return Loss — 33.1 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 55.5 Q + 1.0 jQ Return Loss —25.5 dB Antenna Parameters with Body TSL at 5750 MHz Impedance, transformed to feed point 52.3 Q + 0.8 jQ Return Loss — 32.3 dB Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 52.9 Q — 1.8 jQ Return Loss —29.5 dB Certificate No: D5GHzV2—1060_Jul19 Page 12 of 23 @vv,yl..:,--.. «m engires ruour y ou wy U rd L.

© General Antenna Parameters and Design Electrical Delay (one direction) 1.201 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: D5GHzV2—1060_Jul19 Page 13 of 23

3S ({I DASY5 Validation Report for Head TSL Date: 22.07.2019 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: D5SGHzV2; Serial: D5SGHzV2 — SN:1060 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5250 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 4.46 S/m:; &, = 35.5; p = 1000 kg/m* , Medium parameters used: £ = 5250 MHz; 0 = 4.51 S/m:; & = 35.5; p = 1000 kg/m* , Medium parameters used: f = 5300 MHz; 0 = 4.56 $/m:; &, = 35.4; p = 1000 kg/m* , Medium parameters used: f = 5500 MHz; 0 = 4.76 $/m; & = 35.1; p = 1000 kg/m3 s Medium parameters used: £ = 5600 MHz; 0 = 4.86 S/m; &, = 35; p = 1000 kg/m3 s Medium parameters used: f = 5750 MHz; o = 5.02 $/m:; &, = 34.8; p = 1000 kg/m* , Medium parameters used: £ = 5800 MHz; 0 = 5.07 S$/m; &, = 34.7; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.64, 5.64, 5.64) @ 5200 MHz, ConvF(5.4, 5.4, 5.4) @ 5250 MHz, ConvF(5.39, 5.39, 5.39) @ 5300 MHz, ConvF(5.1, 5.1, 5.1) @ 5500 MHz, ConvF(4.95, 4.95, 4.95) @ 5600 MHz, ConvF(4.98, 4.98, 4.98) @ 5750 MHz, ConvF(4.96, 4.96, 4.96) @ 5800 MHz; Calibrated: 25.03.2019 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 30.04.2019 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 e DASY532 52.10.2(1504); SEMCAD X 14.6.12(7470) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 74.16 V/m; Power Drift = 0.09 dB Peak SAR (extrapolated) = 28.1 W/kg SAR(1 g) = 8.06 W/kg; SAR(10 g) = 2.32 W/kg Maximum value of SAR (measured) = 17.8 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 74.71 V/m; Power Drift = 0.07 dB Peak SAR (extrapolated) = 27.3 W/kg SAR(I g) = 8.07 W/kg; SAR(10 g) = 2.33 W/kg Maximum value of SAR (measured) = 17.8 W/kg Certificate No: D5GHzV2—1060_Jul19 Page 14 of 23

Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 75.07 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 28.8 W/kg SAR(1 g) = 8.23 W/kg; SAR(10 g) = 2.37 W/kg Maximum value of SAR (measured) = 18.5 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 74.21 V/m; Power Drift = 0.7 dB Peak SAR (extrapolated) = 32.1 W/kg SAR(1 g) = 8.51 W/kg; SAR(10 g) = 2.43 W/kg Maximum value of SAR (measured) = 19.6 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 75.03 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 31.0 W/kg SAR(1 g) = 8.49 W/kg; SAR(10 g) = 2.43 W/kg Maximum value of SAR (measured) = 19.4 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 71.89 V/m; Power Drift = 0.09 dB Peak SAR (extrapolated) =31.1 W/kg SAR(I g) = 8.08 W/kg; SAR(10 g) = 2.31 W/kg Maximum value of SAR (measured) = 18.8 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 72.69 V/m; Power Drift = 0.09 dB Peak SAR (extrapolated) = 31.8 W/kg SAR(I g) = 8.14 W/kg; SAR(10 g) = 2.30 W/kg Maximum value of SAR (measured) = 19.0 W/kg Certificate No: D5GHzV2—1060_Jul19 Page 15 of 23

—12.00 —18.00 —24.00 —30.00 0 dB = 19.0 W/kg = 12.79 dBW/kg Certificate No: D5GHzV2—1060_Jul19 Page 16 of 23

© Impedance Measurement Plot for Head TSL (5200, 5250, 5300, 5500, 5600 MHz) File View Channel Sweep Calibration Trace Scale Marker System Window Help »1 uons 5.200000 GHz 48.730 0 5.6041 pF 54615 2 2 5.250000 GHz 48.649 N 7.6569 pF —3.9595 n 3 5.300000 GHz 47.726 0 9.0677 pF 33117 0 4 5.500000 GHz 50.970 n 7.5146 pF —3.8508 N 5 5.600000 GHz 54.204 N 9.1876 pH 323.27 m0 Ch1Aug= 20 Ch1: Start 5.00000 GHa —— Stop 6,00000 GHz GHz —27.727 4B .00 00 00 00 .0 0 Ch 1 C h1: Start 5. 6.00000 GHz Avg=20 Delay Certificate No: D5GHzV2—1060_Jul19 Page 17 of 23

~o — Impedance Measurement Plot for Head TSL (5750, 5800 MHz) File View Channel Sweep Calibration Trace Scale Marker System Window Help 6 5.750000 GHz §1.675 n 3S13pF 44352m0 >7 5.200000 GHz §2.138 0 11.515pF 23630 a Ch1Aug= 20 Ch1: Start 5.00000 GHa —— Stop 600000 GHz 0.00 GHe 34.681 dB 5.00 0.00 00 00 00 00 00 .00 1 = Ch1: Start 5,00000 GHe —— Status CH 1: C*1—Port Avg=20 Delay tCE Certificate No: D5GHzV2—1060_Jul19 Page 18 of 23

({Ifll & DASY5 Validation Report for Body TSL Date: 22.07.2019 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: D5GHzV2; Serial: D5GHzV2 — SN:1060 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5250 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 5.43 S/m; & = 47.3; p = 1000 kg/m3 , Medium parameters used: £ = 5250 MHz; 0 = 5.49 $/m; & = 47.2; p = 1000 kg/m3 s Medium parameters used: £ = 5300 MHz; 0 = 5.56 $/m; & = 47.1; p = 1000 kg/m* , Medium parameters used: £ = 5500 MHz; 0 = 5.83 S/m; & = 46.7; p = 1000 kg/m* , Medium parameters used: £ = 5600 MHz; 0 = 5.97 S/m; &, = 46.6; p = 1000 kg/m3 s Medium parameters used: £ = 5750 MHz; 0 = 6.17 $/m; & = 46.3; p = 1000 kg/m* , Medium parameters used: £ = 5800 MHz; 0 = 6.24 S/m; & = 46.2; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.14, 5.14, 5.14) @ 5200 MHz, ConvF(5.26, 5.26, 5.26) @ 5250 MHz, ConvF(5.25, 5.25, 5.25) @ 5300 MHz, ConvF(4.79, 4.79, 4.79) @ 5500 MHz, ConvF(4.74, 4.74, 4.74) @ 5600 MHz, ConvF(4.62, 4.62, 4.62) @ 5750 MHz, ConvF(4.62, 4.62, 4.62) @ 5800 MHz; Calibrated: 25.03.2019 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 30.04.2019 & Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 e DASY52 52.10.2(1504); SEMCAD X 14.6.12(7470) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.89 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 27.5 W/kg SAR(I g) = 7.41 W/kg; SAR(10 g) = 2.08 W/kg Maximum value of SAR (measured) = 17.2 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 69.26 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 29.2 W/kg SAR(I g) = 7.67 W/kg; SAR(10 g) = 2.15 W/kg Maximum value of SAR (measured) = 17.9 W/kg Certificate No: D5GHzV2—1060_Jul19 Page 19 of 23


Document Created: 2019-09-25 16:24:11
Document Modified: 2019-09-25 16:24:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC