I19Z61557-SEM01_SAR_Rev0_2

FCC ID: ZNFX540EMW

RF Exposure Info

Download: PDF
FCCID_4462397

No.I19Z61557-SEM01 Page 113 of 192 ANNEX G Probe Calibration Certificate Probe 3617 Calibration Certificate ©Copyright. All rights reserved by CTTL.

() R Calibration Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland fi“@"’& ifi\t_//El Lorne IE}". 4'/,,/'fi\\“\c g ( 53 Schweizerischer Kalibrierdienst Service suisse d‘étalonnage Servizio svizzero di taratura Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one ofthe signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B, C, D modulation dependent linearization parameters Polarization q ip rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), i.e., $ = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, ", "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand— held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 ©) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR)for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: NORMx,y,z: Assessed for E—field polarization 9 = 0 (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not affect the E*—field uncertainty inside TSL (see below ConvF). NORM(Mx,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics Axy.z; Bxy.z: Cx,y,z; Dx,y,z; VRx,y,z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. Sensor Offset: The sensoroffset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: EX3—3617_Jan19 Page 2 of 19

® EX3DV4 — SN:3617 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3617 Basic Calibration Parameters Sensor X Sensor Y Sensor Z January 31, 2019 Unc (k=2) Norm (uV/(V/m))* 0.35 0.21 0.32 101 % DCP (mV)" 102.9 95.7 101.9 Calibration Results for Modulation Response UID Communication System Name A B C D VR Max Max dB dB\uV dB mV dev. Unc® (k=2) 0 Cw x |_0.00 0.00 1.00 0.00 1514 £3.0% £4.7% y |_0.00 0.00 1.00 154.7 z |_0.00 0.00 1.00 150.4 10352— Pulse Waveform (200Hz, 10%) x 5.31 7342 i4.63 10.00 60.0 £26% £96% AAA Y 286 6584 11.90 60.0 z 15.00 87.67 20.10 60.0 10353— Pulse Waveform (200Hz, 20%) x 1057 8197 1623 6.99 80.0 £1.7% £96% AAA y 2.03 65.40 10.27 80.0 z 15.00 89.79 19.80 80.0 10354— Pulse Waveform (200Hz, 40%) x 15.00 86.62 1629 3.98 95.0 #11% £96% AAA Y 082 6150 6.58 95.0 z 15.00 97.47 22.01 95.0 10355— Pulse Waveform (200Hz, 60%) x 15.00 8999 1664 222 1200 £12% £9.6% AAA y 0.40 60.00 3.98 120.0 Z 15.00 114.21 28.32 120.0 10387— QPSK Waveform, 1 MHz x 0.65 6236 8.93 0.00 150.0 £39% £96% AAA y 0.45 60.00 5.43 150.0 z 0.90 65.62 10.92 150.0 10388— QPSK Waveform, 10 MHz x 242 foss i716 0.00 1500 £18% £9.6% AAA y 1.99 67.57 15.24 150.0 z2 |_271 7239 1822 150.0 10396— 64—QAM Waveform, 100 kHz x s7s 7533 2079 301 150.0 £07% £9.6% AAA y 323 .01 1881 150.0 z 371 7494 20.97 150.0 10399— 64—QAM Waveform, 40 MHz x 358 6811 1637 0.00 |150.0 £4.0% £96% AAA y 3.32 66.75 15.59 150.0 z 3.71 68.68 16.83 150.0 10414— WLAN CCDF, 64—QAM, 40MHz x 484 6621 15.87 0.00 150.0 £67% £9.6% AAA y 448 64.72 1519 150.0 z 4.93 6643 1614 150.0 Note: For details on UID parameters see Appendix The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X,Y,Z do not affect the E*—field uncertainty inside TSL (see Pages 5 and 6). © Numerical linearization parameter: uncertainty not required. £ Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: EX3—3617_Jan19 Page 3 of 19

EX3DV4— SN:3617 January 31, 2019 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3617 Sensor Model Parameters 61 C2 a T1 T2 T3 T4 T5 T6 fF fF V ms.V~* ms.V~‘ ms V V~ X 38.8 281.02 33.02 10.58 0.71 4.99 1.88 0.20 1.01 ¥ 39.2 310.65 39.54 8.92 1.27 5.05 0.00 0.75 1.01 Z 40.7 300.62 35.22 10.39 0.59 5.05 1.28 0.33 1.01 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 14.6 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 1.4 mm Certificate No: EX3—3617_Jan19 Page 4 of 19

® EX3DV4— SN:3617 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3617 Calibration Parameter Determined in Head Tissue Simulating Media January 31, 2019 Relative Conductivity Depth ° Une f(MHz)© Permittivity" (S/m)" ConvFX ConvF¥Y ConvFZ Aipha® _(mm) (k=2) 64 54.2 0.75 1245 1245 12.45 0.00 1.00 £13.3% 150 52.3 0.76 11.88 11.88 11.88 0.00 1.00 £13.3% 300 45.3 0.87 11.40 11.40 11.40 0.08 1.20 £13.3% 450 43.5 0.87 10.54 10.54 10.54 0.14 1.40 £13.3% 750 41.9 0.89 10.03 10.03 10.03 0.63 0.84 £12.0 % 835 41.5 0.90 9.75 9.75 9.75 0.39 0.95 £12.0 % 900 41.5 0.97 9.66 9.66 9.66 0.47 0.85 £12.0 % 1450 40.5 1.20 8.68 8.68 8.68 0.37 0.80 +12.0 % 1640 40.2 1.31 8.48 8.48 8.48 0.38 0.80 £12.0 % 1750 40.1 187 8.38 8.38 8.38 0.36 0.82 £12.0 % 1810 40.0 1.40 8.11 8.11 811 0.32 0.84 £12.0 % 1900 40.0 1.40 8.14 8.14 8.14 0.32 0.85 £12.0 % 2000 40.0 1.40 8.13 8.13 8.13 0.28 0.84 £12.0 % 2100 39.8 1.49 8.30 8.30 8.30 0.37 0.85 £12.0 % 2300 39.5 1.67 7.74 7.74 7.74 0.32 0.84 £12.0 % 2450 39.2 1.80 7.62 7.62 7.62 0.31 0.95 £12.0 % 2600 39.0 1.96 7.19 7.19 719 0.43 0.85 £12.0 % 3300 38.2 971 6.98 6.98 6.98 0.25 1.20 £13.1% 3500 37.9 2.91 6.97 6.97 6.97 0.50 1.20 £13.1% 3700 37.7 3.12 6.89 6.89 6.89 0.20 1.20 £13.1% 3900 37.5 3.32 6.88 6.88 6.88 0.20 1.20 £13.1% 4600 36.7 4.04 6.84 6.84 6.84 0.20 1.50 £13.1% 4950 36.3 4.40 5.60 5.60 5.60 0.40 1.80 £13.1% 5200 36.0 4.66 5.50 5.50 5.50 0.40 1.80 £13.1% 5250 35.9 4.71 5.39 5.39 5.39 0.40 1.80 £13.1% 5300 35.9 4.76 5.25 5.25 525 0.40 1.80 £13.1% 5500 35.6 4.96 5.18 5.18 518 0.40 1.80 £13.1% 5600 35.5 5.07 5.06 5.06 5.06 0.40 1.80 £13.1% 5750 35.4 5.22 5.07 5.07 5.07 0.40 1.80 £13.1% 5800 35.3 5.27 5.04 5.04 5.04 0.40 1.80 £13.1% © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHzis + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Validity of ConvF assessed at 6 MHz is 4—9 MHz, and ConvF assessed at 13 MHz is 9—19 MHz. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters ( and a) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (c and a) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—3617_Jan19 Page 5 of 19

8 EX3DV4— SN:3617 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3617 Calibration Parameter Determined in Body Tissue Simulating Media January 31, 2019 Relative Conductivity Depth ° Unc f(MHz)© Permittivity" (S/m)" ConvFX ConvFY ConvFZ Aipha® _(mm) (k=2) 150 61.9 0.80 11.45 11.45 11.45 0.00 1.00 £13.3% 300 58.2 0.92 10.57 10.57 10.57 0.03 1.20 £13.3 % 450 56.7 0.94 10.39 10.39 10.39 0.08 1.20 £13.3 % 750 55.5 0.96 9.85 9.85 9.85 0.50 0.84 + 12.0 % 835 55.2 0.97 9.61 9.61 9.61 0.37 0.95 + 12.0 % 900 55.0 1.05 9.57 9.57 9.57 0.45 0.84 + 12.0 % 1450 54.0 1.30 8.33 8.33 8.33 0.34 0.80 + 12.0 % 1640 53.7 1.42 8.53 8.53 8.53 0.35 0.80 +12.0 % 1750 53.4 1.49 8.03 8.03 8.03 0.39 0.84 +12.0 % 1810 53.3 1.52 7.94 7.94 7.94 0.43 0.84 + 12.0 % 1900 53.3 1.52 7.78 7.78 7.78 0.38 0.87 + 12.0 % 2000 53.3 1.52 8.00 8.00 8.00 0.22 1.15 * 12.0 % 2100 53.2 1.62 8.23 8.23 8.23 0.41 0.85 + 12.0 % 2300 52.9 1.81 7.84 7.84 784 0.40 0.84 + 12.0 % 2450 52.7 1.95 7.79 7.79 7.19 0.31 0.86 +12.0 % 2600 52.5 216 7.49 7.49 749 0.26 0.98 + 12.0 % 3500 51.3 3.31 6.86 6.86 6.86 0.25 1.20 #13.1 % 3700 51.0 3.55 6.60 6.60 6.60 0.26 1.25 £13.1% 3900 51.2 3.78 6.69 6.69 6.69 0.26 1.25 £13.1% 4600 49.8 4.60 6.50 6.50 6.50 0.28 1.30 £13.1% 3500 51.3 3.31 6.46 6.46 646 0.20 1.70 £13.1% 4950 49.4 5.01 4.99 4.99 4.99 0.50 1.90 £13.1% 5200 49.0 5.30 4.84 4.84 4.84 0.50 1.90 £13.1% 5250 48.9 5.36 4.76 4.76 4.76 0.50 1.90 £13.1% 5300 48.9 5.42 4.63 4.63 4.63 0.50 1.90 £13.1% 5500 48.6 5.65 4.32 4.32 4.32 0.50 1.90 £13.1% 5600 48.5 5.77 4.23 4.23 4.23 0.50 1.90 £13.1% 5750 48.3 5.94 4.36 4.36 4.36 0.50 1.90 £13.1 % 5800 48.2 6.00 4.24 4.24 4.24 0.50 1.90 £13.1 % © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty forthe indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Validity of ConvF assessed at 6 MHz is 4—9 MHz, and ConvF assessed at 13 MHz is 9—19 MHz. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (e and a) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (c and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants thatthe remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance largerthan half the probe tip diameter from the boundary. Certificate No: EX3—3617_Jan19 Page 6 of 19

EX3DV4— SN:3617 January 31, 2019 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) HTTTT T¥ Frequency response (normalized) 5 1 l10i00 o Ten Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: EX3—3617_Jan19 Page 7 of 19

EX3DV4— SN:3617 January 31, 2019 Receiving Pattern (¢), 9 = 0° f=600 MHz,TEM f=1800 MHz,R22 I Fag ‘, + # & f ® ® e 6 ® e niol Tot X Y Tot x Y Z Error [dB] 10%2 GOE Mriz 190%Hz 25@& Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: EX3—3617_Jan19

TTL T EX3DV4— SN:3617 January 31, 2019 Dynamic Range f(SARneaq) (TEM cell , fevai= 1900 MHz) Input Signal [uV] 103 102 101 10 10‘ 10 10 SAR [mW/cm3] not compensated compensated Error [dB] 103 102 101 100 101 102 103 SAR [mW/cm3] Ce] not compensated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—3617_Jan19 Page 9 of 19

) <|| S EX3DV4— SN:3617 10 f= 835 MHz,WGLS R9 (H_convF) Conversion Factor Assessment January 31, 2019 f= 1900 MHz,WGLS R22 (H_convF) 20| } 20 & % , % % y 2 20 | &0 46 c 1 | is ‘ 04 10 I | P o a [() : ho s & 0n o s [W O ao Deviation from Isotropy in Liquid Error (¢, 8), f = 900 MHz Deviation M —~1.0 —0.8 —0.6 —0.4 —0.2 00 02 0.4 0.6 08 1.0 Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: EX3—3617_Jan19 Page 10 of 19

) (@ S ~o — EX3DV4— SN:3617 January 31, 2019 Appendix: Modulation Calibration Parameters UID Rev Communication System Name Group PAR Unc® (dB) (k=2) 0 Cw CW 0.00 * 4.7 % 10010 CAA SAR Validation (Square, 100ms, 10ms) Test 10.00 £9.6 % 10011 CAB UMTS—FDD (WCDMA) WCDMA 2.91 +9.6 % 10012 CAB IEEE 802.11b WiFi 2.4 GHz (DSSS, 1 Mbps) WLAN 1.87 + 9.6 % 10013 CAB_| IEEE 802.11g WiFi 2.4 GHz (DSSS—OFDM, 6 Mbps) WLAN 9.46 +9.6 % 10021 DAC GSM—FDD (TDMA, GMSK) GSM 9.39 + 9.6 % 10023 DAC GPRS—FDD (TDMA, GMSK, TN 0) GSM 9.57 + 9.6 % 10024 DAC GPRS—FDD (TDMA, GMSK, TN 0—1) GSM 6.56 + 9.6 % 10025 DAC EDGE—FDD (TDMA, 8PSK, TN 0) GSM 12.62 £9.6 % 10026 DAC EDGE—FDD (TDMA, 8PSK, TN 0—1) GSM 9.55 + 9.6 % 10027 DAC GPRS—FDD (TDMA, GMSK, TN 0—1—2) GSM 4.80 + 9.6 % 10028 DAC GPRS—FDD (TDMA, GMSK, TN 0—1—2—3) GSM 3.55 + 9.6 % 10029 DAC EDGE—FDD (TDMA, 8PSK, TN 0—1—2) GSM 7.78 + 9.6 % 10030 CAA IEEE 802.15.1 Bluetooth (GFSK, DH1) Bluetooth 5.30 + 9.6 % 10031 CAA IEEE 802.15.1 Bluetooth (GFSK, DH3) Bluetooth 1.87 * 9.6 % 10032 CAA IEEE 802.15.1 Bluetooth (GFSK, DH5) Bluetooth 1.16 + 9.6 % 10033 CAA IEEE 802.15.1 Bluetooth (PI4—DQPSK, DH1) Bluetooth 7.74 + 9.6 % 10034 CAA IEEE 802.15.1 Bluetooth (PI/4—DQPSK, DH3) Bluetooth 4.53 + 9.6 % 10035 CAA IEEE 802.15.1 Bluetooth (PI4—DQPSK, DH5) Bluetooth 3.83 + 9.6 % 10036 CAA IEEE 802.15.1 Bluetooth (8—DPSK, DH1) Bluetooth 8.01 + 9.6 % 10037 CAA IEEE 802.15.1 Bluetooth (8—DPSK, DH3) Bluetooth 4.77 * 9.6 % 10038 CAA IEEE 802.15.1 Bluetooth (8—DPSK, DH5) Bluetooth 4.10 + 9.6 % 10039 CAB__| CDMA2000 (1xRTT, RC1) CDMA2000 4.57 + 9.6 % 10042 CAB__| 1S—54 / 1S—136 FDD (TDMA/FDM, PI/4—DQPSK, Halfrate) AMPS 7.78 + 9.6 % 10044 CAA IS—91/EIA/TIA—553_FDD (FDMA, FM) AMPS 0.00 + 9.6 % 10048 CAA DECT (TDD, TDMA/FDM, GFSK, Full Slot, 24) DECT 13.80 £9.6 % 10049 CAA DECT (TDD, TDMA/FDM, GFSK, Double Slot, 12) DECT 10.79 £9.6 % 10056 CAA UMTS—TDD (TD—SCDMA, 1.28 Mops) TD—SCDMA 11.01 +9.6 % 10058 DAC EDGE—FDD (TDMA, 8PSK, TN 0—1—2—3) GSM 6.52 + 9.6 % 10059 CAB IEEE 802.11b WiFi 2.4 GHz (DSSS, 2 Mbps) WLAN 212 + 9.6 % 10060 CAB IEEE 802.1 1b WiFi 2.4 GHz (DSSS, 5.5 Mbps) WLEAN 2.83 + 9.6 % 10061 CAB_| IEEE 802.11b WiFi 2.4 GHz (DSSS, 11 Mbps) WLAN 3.60 + 9.6 % 10062 CAC IEEE 802.11a/h WiFi 5 GHz (OFDM, 6 Mbps) WLAN 8.68 + 9.6 % 10063 CAC IEEE 802.1 1a/h WiFi 5 GHz (OFDM, 9 Mbps) WLAN 8.63 + 9.6 % 10064 CAC IEEE 802.1 1a/h WiFi 5 GHz (OFDM, 12 Mbps) WLAN 9.09 + 9.6 % 10065 CAC IEEE 802.11a/h WiFi 5 GHz (OFDM, 18 Mbps) WLAN 9.00 + 9.6 % 10066 CAC IEEE 802.11a/h WiFi 5 GHz (OFDM, 24 Mbps) WLAN 9.38 + 9.6 % 10067 CAC IEEE 802.1 1a/h WiFi 5 GHz (OFDM, 36 Mbps) WLAN 10.12 £9.6 % 10068 CAC IEEE 802.11a/h WiFi 5 GHz (OFDM, 48 Mbps) WLAN: 10.24 £9.6 % 10069 CAC IEEE 802.11a/h WiFi 5 GHz (OFDM, 54 Mbps) WLAN: 10.56 £9.6 % 10071 CAB IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 9 Mbps) WLAN 9.83 + 9.6 % 10072 CAB_| IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 12 Mbps) WLAN 9.62 + 9.6 % 10073 CAB IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 18 Mbps) WLAN 9.94 + 9.6 % 10074 CAB_| IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 24 Mbps) WLAN 10.30 £9.6 % 10075 CAB_| IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 36 Mbps) WLAN 10.77 £9.6 % 10076 CAB IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 48 Mbps) WLAN 10.94 £9.6 % 10077 CAB_| IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 54 Mbps) WLAN 11.00 £9.6 % 10081 CAB__| CDMA2000 (1xRTT, RC3) CDMA2000 3.97 + 9.6 % 10082 CAB 1S—54 / IS—136 FDD (TDMA/FDM, PI/4—DQPSK, Fullrate) AMPS 4.77 + 9.6 % 10090 DAC GPRS—FDD (TDMA, GMSK, TN 0—4) GSM 6.56 + 9.6 % 10097 CAB__| UMTS—FDD (HSDPA) WCDMA 3.98 + 9.6 % 10098 CAB UMTS—FDD (HSUPA, Subtest 2) WCDMA 3.98 + 9.6 % 10099 DAC EDGE—FDD (TDMA, 8PSK, TN 0—4) GSM 9.55 + 9.6 % 10100 CAE LTE—FDD (SC—FDMA, 100% RB, 20 MHz, QPSK) LTE—FDD 5.67 + 9.6 % 10101 CAE LTE—FDD (SC—FDMA, 100% RB, 20 MHz, 16—QAM) LTE—FDD 6.42 + 9.6 % 10102 CAE LTE—FDD (SC—FDMA, 100% RB, 20 MHz, 64—QAM) LTE—FDD 6.60 + 9.6 % 10103 CAG LTE—TDD (SC—FDMA, 100% RB, 20 MHz, QPSK) LTE—TDD 9.29 + 9.6 % 10104 CAG LTE—TDD (SC—FDMA, 100% RB, 20 MHz, 16—QAM) LTE—TDD 9.97 + 9.6 % 10105 CAG LTE—TDD (SC—FDMA, 100% RB, 20 MHz, 64—QAM) LTE—TDD 10.01 £9.6 % 10108 CAG LTE—FDD (SC—FDMA, 100% RB, 10 MHz, QPSK) LTE—FDD 5.80 + 9.6 % Certificate No: EX3—3617_Jan19 Page 11 of 19

ttg o 9 9 —> EX3DV4— SN:3617 January 31, 2019 10109 CAG LTE—FDD (SC—FDMA, 100% RB, 10 MHz, 16—QAM) LTE—FDD 6.43 + 9.6 % 10110 CAG LTE—FDD (SC—FDMA, 100% RB, 5 MHz, QPSK) LTE—FDD 5.75 + 9.6 % 10111 CAG LTE—FDD (SC—FDMA, 100% RB, 5 MHz, 16—QAM) LTE—FDD 6.44 + 9.6 % 10112 CAG LTE—FDD (SC—FDMA, 100% RB, 10 MHz, 64—Q0AM) LTE—FDD 6.59 + 9.6 % 10113 CAG LTE—FDD (SC—FDMA, 100% RB, 5 MHz, 64—QAM) LTE—FDD 6.62 + 9.6 % 10114 CAC IEEE 802.11n (HT Greenfield, 13.5 Mbps, BPSK) WLAN 8.10 + 9.6 % 10115 CAC IEEE 802.11n (HT Greenfield, 81 Mbps, 16—QAM) WLAN 8.46 + 9.6 % 10116 CAC IEEE 802.11n (HT Greenfield, 135 Mbps, 64—QAM) WLAN 8.15 + 9.6 % 10117 CAC IEEE 802.11n (HT Mixed, 13.5 Mbps, BPSK) WLAN 8.07 +9.6 % 10118 CAC IEEE 802.11n (HT Mixed, 81 Mbps, 16—QAM) WLAN 8.59 + 9.6 % 10119 CAC IEEE 802.11n (HT Mixed, 135 Mbps, 64—QAM) WLAN 8.13 £9.6 % 10140 CAE LTE—FDD (SC—FDMA, 100% RB, 15 MHz, 16—QAM) LTE—FDD 6.49 £9.6 % 10141 CAE LTE—FDD (SC—FDMA. 100% RB. 15 MHz. 64—QAM) LTE—FDD 6.53 £9.6 % 10142 CAE LTE—FDD (SC—FDMA, 100% RB, 3 MHz, QPSK) LTE—FDD 5.73 + 9.6 % 10143 CAE LTE—FDD (SC—FDMA, 100% RB, 3 MHz, 16—QAM) LTE—FDD 6.35 + 9.6 % 10144 CAE LTE—FDD (SC—FDMA, 100% RB, 3 MHz, 64—QAM) LTE—FDD 6.65 £9.6 % 10145 CAF LTE—FDD (SC—FDMA, 100% RB, 1.4 MHz, QPSK) LTE—FDD 5.76 £9.6 % 10146 CAF LTE—FDD (SC—FDMA, 100% RB, 1.4 MHz, 16—QAM) LTE—FDD 6.41 + 9.6 % 10147 CAF LTE—FDD (SC—FDMA, 100% RB, 1.4 MHz, 64—QAM) LTE—FDD 6.72 + 9.6 % 10149 CAE LTE—FDD (SC—FDMA, 50% RB, 20 MHz, 16—QAM) LTE—FDD 6.42 + 9.6 % 10150 CAE LTE—FDD (SC—FDMA, 50% RB, 20 MHz, 64—QAM) LTE—FDD 6.60 + 9.6 % 10151 CAG LTE—TDD (SC—FDMA, 50% RB, 20 MHz, QPSK) LTE—TDD 9.28 + 9.6 % 10152 CAG LTE—TDD (SC—FDMA, 50% RB, 20 MHz, 16—QAM) LTE—TDD 9.92 + 9.6 % 10153 CAG LTE—TDD (SC—FDMA, 50% RB, 20 MHz, 64—QAM) LTE—TDD 10.05 £9.6 % 10154 CAG LTE—FDD (SC—FDMA, 50% RB, 10 MHz, QPSK) LTE—FDD 5.75 + 9.6 % 10155 CAG LTE—FDD (SC—FDMA, 50% RB, 10 MHz, 16—QAM) LTE—FDD 6.43 + 9.6 % 10156 CAG LTE—FDD (SC—FDMA, 50% RB, 5 MHz, QPSK) LTE—FDD 5.79 + 9.6 % 10157 CAG LTE—FDD (SC—FDMA, 50% RB, 5 MHz, 16—QAM) LTE—FDD 6.49 +9.6 % 10158 CAG LTE—FDD (SC—FDMA, 50% RB, 10 MHz, 64—QAM) LTE—FDD 6.62 + 9.6 % 10159 CAG LTE—FDD (SC—FDMA, 50% RB, 5 MHz, 64—QAM) LTE—FDD 6.56 + 9.6 % 10160 CAE LTE—FDD (SC—FDMA, 50% RB, 15 MHz, QPSK) LTE—FDD 5.82 + 9.6 % 10161 CAE LTE—FDD (SC—FDMA, 50% RB, 15 MHz, 16—QAM) LTE—FDD 6.43 + 9.6 % 10162 CAE LTE—FDD (SC—FDMA, 50% RB, 15 MHz, 64—QAM) LTE—FDD 6.58 + 9.6 % 10166 _| CAF LTE—FDD (SC—FDMA, 50% RB, 1.4 MHz, QPSK) LTE—FDD 5.46 +9.6 % 10167 CAF LTE—FDD (SC—FDMA, 50% RB, 1.4 MHz, 16—QAM) LTE—FDD 6.21 + 9.6 % 10168 CAF LTE—FDD (SC—FDMA, 50% RB, 1.4 MHz, 64—QAM) LTE—FDD 6.79 + 9.6 % 10169 CAE LTE—FDD (SC—FDMA, 1 RB, 20 MHz, QPSK) LTE—FDD 5.73 + 9.6 % 10170 CAE LTE—FDD (SC—FDMA, 1 RB, 20 MHz, 16—QAM) LTE—FDD 6.52 + 9.6 % 10171 AAE LTE—FDD (SC—FDMA, 1 RB, 20 MHz, 64—QAM) LTE—FDD 6.49 + 9.6 % 10172 CAG LTE—TDD (SC—FDMA, 1 RB, 20 MHz, QPSK) LTE—TDD 9.21 + 9.6 % 10173 CAG LTE—TDD (SC—FDMA, 1 RB, 20 MHz, 16—QAM) LTE—TDD 9.48 + 9.6 % 10174 CAG LTE—TDD (SC—FDMA, 1 RB, 20 MHz, 64—QAM) LTE—TDD 10.25 £9.6 % 10175 CAG LTE—FDD (SC—FDMA, 1 RB, 10 MHz, QPSK) LTE—FDD 5.72 + 9.6 % 10176 CAG LTE—FDD (SC—FDMA, 1 RB, 10 MHz, 16—QAM) LTE—FDD 6.52 + 9.6 % 10177 CAl LTE—FDD (SC—FDMA, 1 RB, 5 MHz, QPSK) LTE—FDD 5.73 +9.6 % 10178 CAG LTE—FDD (SC—FDMA, 1 RB, 5 MHz, 16—QAM) LTE—FDD 6.52 + 9.6 % 10179 CAG LTE—FDD (SC—FDMA, 1 RB, 10 MHz, 64—QAM) LTE—FDD 6.50 + 9.6 % 10180 CAG LTE—FDD (SC—FDMA, 1 RB, 5 MHz, 64—QAM) LTE—FDD 6.50 + 9.6 % 10181 CAE LTE—FDD (SC—FDMA, 1 RB, 15 MHz, QPSK) LTE—FDD 5.72 + 9.6 % 10182 CAE LTE—FDD (SC—FDMA, 1 RB, 15 MHz, 16—QAM) LTE—FDD 6.52 +9.6 % 10183 AAD LTE—FDD (SC—FDMA, 1 RB, 15 MHz, 64—QAM) LTE—FDD 6.50 +9.6 % 10184 CAE LTE—FDD (SC—FDMA, 1 RB, 3 MHz, QPSK) LTE—FDD 5.73 £9.6 % 10185 CAE LTE—FDD (SC—FDMA, 1 RB, 3 MHz, 16—QAM) LTE—FDD 6.51 £9.6 % 10186 AAE LTE—FDD (SC—FDMA, 1 RB, 3 MHz, 64—QAM) LTE—FDD 6.50 £9.6 % 10187 CAF LTE—FDD (SC—FDMA, 1 RB, 1.4 MHz, QPSK) LTE—FDD 5.73 + 9.6 % 10188 CAF LTE—FDD (SC—FDMA, 1 RB, 1.4 MHz, 16—QAM) LTE—FDD 6.52 + 9.6 % 10189 AAF LTE—FDD (SC—FDMA, 1 RB, 1.4 MHz, 64—QAM) LTE—FDD 6.50 £9.6 % 10193 CAC IEEE 802.11n (HT Greenfield, 6.5 Mbps, BPSK) WLAN 8.09 +9.6 % 10194 CAC IEEE 802.11n (HT Greenfield, 39 Mbps, 16—QAM) WLAN 8.12 + 9.6 % 10195 CAC IEEE 802.11n (HT Greenfield, 65 Mbps, 64—QAM) WLAN 8.21 + 9.6 % 10196 CAC IEEE 802.11n (HT Mixed, 6.5 Mbps, BPSK) WLAN 8.10 + 9.6 % 10197 CAC IEEE 802.11n (HT Mixed, 39 Mbps, 16—QAM) WLAN 8.13 + 9.6 % 10198 CAC IEEE 802.11n (HT Mixed, 65 Mbps, 64—QAM) WLAN 8.27 + 9.6 % 10219 CAC IEEE 802.11n (HT Mixed, 7.2 Mbps, BPSK) WLAN 8.03 + 9.6 % Certificate No: EX3—3617_Jan19 Page 12 of 19


Document Created: 2019-09-25 16:24:10
Document Modified: 2019-09-25 16:24:10
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC