test report RF

FCC ID: ZNFX430EMW

Test Report

Download: PDF
FCCID_4435289

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: ZR/2019/7002101 Page: 1 of 21 FCC TEST REPORT Application No: ZR/2019/70021 Applicant: LG Electronics USA, Inc. Address of Applicant 1000 Sylvan Ave. Englewood Cliffs, New Jersey, United States 07632 Manufacturer: Huaqin Telecom Technology Co., Ltd. Address of Manufacturer: No.1 Building,No.9 Building,No.399,Keyuan Road, Zhangjiang Hi-tech Park,Shanghai,P.R.China Factory: Dong Guan Huabel Electronic Technology Co.,Ltd Address of Factory: No.9 Industrial Northern Road,National High-Tech Industrial Development Zone,SongShan Lake,Dong Guan EUT Description: Mobile Handset Model No.: LM-X430EMW Trade Mark: LG FCC ID: ZNFX430EMW Standards: 47 CFR Part 2 47 CFR Part 22 subpart H 47 CFR Part 24 subpart E Test Method: FCC KDB 971168 D01 Power Meas License Digital Systems V03r01 C63.26 (2015) Date of Receipt: 2019/7/31 Date of Test: 2019/7/20 to 2019/8/26 Date of Issue: 2019/8/26 Test Result: PASS * * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Authorized Signature: Derek Yang Wireless Laboratory Manager

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 2 of 21 1 Version Revision Record Version Chapter Date Modifier Remark 00 2019/8/26 Original Authorized for issue by: Tested By 2019/8/26 (Mike Hu) /Project Engineer Date Checked By 2019/8/26 (David Chen) /Reviewer Date

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 3 of 21 Content 1 VERSION ......................................................................................................................................................... 2 2 TEST SUMMARY ............................................................................................................................................ 5 2.1 GSM850/UMTS BAND 5 ......................................................................................................................... 5 2.2 GSM 1900/UMTS BAND 2....................................................................................................................... 5 3 GENERAL INFORMATION ............................................................................................................................ 6 3.1 CLIENT INFORMATION ............................................................................................................................... 6 3.2 TEST LOCATION ........................................................................................................................................ 6 3.3 TEST FACILITY .......................................................................................................................................... 6 3.4 GENERAL DESCRIPTION OF EUT .............................................................................................................. 7 3.5 TEST MODE .............................................................................................................................................. 7 3.6 TEST ENVIRONMENT ................................................................................................................................. 7 3.7 TECHNICAL SPECIFICATION ....................................................................................................................... 8 3.8 TEST FREQUENCIES.................................................................................................................................. 9 4 DESCRIPTION OF TESTS............................................................................................................................10 4.1 CONDUCTED OUTPUT POWER .................................................................................................................10 4.2 EFFECTIVE (ISOTROPIC) RADIATED POWER OF TRANSMITTER .................................................................10 4.3 OCCUPIED BANDWIDTH............................................................................................................................10 4.4 BAND EDGE AT ANTENNA TERMINALS ......................................................................................................11 4.5 SPURIOUS AND HARMONIC EMISSIONS AT ANTENNA TERMINAL ...............................................................11 4.6 PEAK-AVERAGE RATIO ............................................................................................................................12 4.7 FIELD STRENGTH OF SPURIOUS RADIATION .............................................................................................13 4.8 FREQUENCY STABILITY / TEMPERATURE VARIATION ................................................................................14 4.9 TEST SETUPS ..........................................................................................................................................15 4.9.1 Test Setup 1 ......................................................................................................................................15 4.9.2 Test Setup 2 ......................................................................................................................................15 4.9.3 Test Setup 3 ......................................................................................................................................16 4.9.4 Test Setup 4 ......................................................................................................................................16 4.10 TEST CONDITIONS ...................................................................................................................................17 5 MAIN TEST INSTRUMENTS ........................................................................................................................19

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 4 of 21 6 MEASUREMENT UNCERTAINTY ...............................................................................................................21 7 APPENDIXES.................................................................................................................................................21

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 5 of 21 2 Test Summary 2.1 GSM850/UMTS Band 5 Test Item FCC Rule No. Requirements Test Result Verdict Effective (Isotropic) §2.1046, Section 1 of Radiated Power ERP ≤ 7 W Pass §22.913 Appendix B Output Data Peak-Average Section 2 of --- Limit≤13 dB Pass Ratio Appendix B Modulation Section 3 of §2.1047 Digital modulation Pass Characteristics Appendix B OBW: No limit. Section 4 of Bandwidth §2.1049 Pass EBW: No limit. Appendix B ≤ -13 dBm/1%*EBW, in 1 MHz bands Band Edges §2.1051, Section 5 of immediately outside and adjacent to the Pass Compliance §22.917 Appendix B frequency block. Spurious Emission FCC: ≤ -13 dBm/100 kHz, from 9 kHz to §2.1051, Section 6 of at Antenna 10th harmonics but outside authorized Pass §22.917 Appendix B Terminals operating frequency ranges. Field Strength of §2.1053, Section 7 of ≤ -13 dBm/100 kHz. Pass Spurious Radiation §22.917 Appendix B §2.1055, Section 8 of Frequency Stability ≤ ±2.5ppm. Pass §22.355 Appendix B Remark: For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”. 2.2 GSM 1900/UMTS Band 2 Test Item FCC Rule No. Requirements Test Result Verdict Effective (Isotropic) §2.1046, Section 1 of Radiated Power EIRP ≤ 2 W Pass §24.232 Appendix B Output Data Peak-Average §2.1046, Section 2 of Limit≤13 dB Pass Ratio §24.232 Appendix B Modulation Section 3 of §2.1047 Digital modulation Pass Characteristics Appendix B OBW: No limit. Section 4 of Bandwidth §2.1049 Pass EBW: No limit. Appendix B ≤ -13 dBm/1%*EBW, in 1 MHz bands Band Edges §2.1051, Section 5 of immediately outside and adjacent to the Pass Compliance §24.238 Appendix B frequency block. Spurious Emission ≤ -13 dBm/1 MHz, from 9 kHz to 10th §2.1051, Section 6 of at Antenna harmonics but outside authorized Pass §24.238 Appendix B Terminals operating frequency ranges. Field Strength of §2.1053, Section 7 of ≤ -13 dBm/1 MHz. Pass Spurious Radiation §24.238 Appendix B §2.1055, Section 8 of Frequency Stability ≤ ±2.5 ppm. Pass §24.235 Appendix B Remark: For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 6 of 21 3 General Information 3.1 Client Information Applicant: LG Electronics USA, Inc. Address of Applicant: 1000 Sylvan Ave. Englewood Cliffs, New Jersey, United States 07632 Manufacturer: Huaqin Telecom Technology Co., Ltd. No.1 Building,No.9 Building,No.399,Keyuan Road, Zhangjiang Hi-tech Address of Manufacturer: Park,Shanghai,P.R.China Factory: Dong Guan Huabel Electronic Technology Co.,Ltd No.9 Industrial Northern Road,National High-Tech Industrial Address of Factory: Development Zone,SongShan Lake,Dong Guan 3.2 Test Location Company: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Address: Shenzhen, Guangdong, China Post code: 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 E-mail: ee.shenzhen@sgs.com 3.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 7 of 21 3.4 General Description of EUT EUT Description: Mobile Handset Model No.: LM-X430EMW Trade Mark: LG Hardware Version: Rev.1.0 Software Version: V09c Sample Type: Portable Device, Module Antenna Type: External, Integrated GSM850: -0.6dBi; GSM1900: -0.7dBi Antenna Gain: WCDMA Band II: -0.7dBi WCDMA Band V: -0.6dBi 3.5 Test Mode Test Mode Test Modes Description GSM/TM1 GSM system, GSM/GPRS, GMSK modulation GSM/TM2 GSM system, EGPRS, 8PSK modulation UMTS/TM1 UMTS system, WCDMA, QPSK modulation UMTS/TM2 UMTS system, WCDMA, 16QAM modulation Remark: The test mode(s) are selected according to relevant radio technology specifications. 3.6 Test Environment Environment Parameter Selected Values During Tests Relative Humidity 52% Atmospheric Pressure: 101.32 KPa Temperature NT 25 °C LV 3.8V Voltage: NV 3.4V HV 4.38V Remark: LV= lower extreme test voltage; NV= nominal voltage HV= upper extreme test voltage; NT= normal temperature

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 8 of 21 3.7 Technical Specification Characteristics Description GSM Radio System Type UMTS Band TX RX GSM850 824 to 849 MHz 869 to 894 MHz Supported Frequency GSM1900 1850 to 1910 MHz 1930 to 1990 MHz Range UMTS Band II 1850 to 1910 MHz 1930 to 1990 MHz UMTS Band V 824 to 849 MHz 869 to 894 MHz GSM850:34 dBm Target TX Output GSM1900: 31dBm Power UMTS Band II: 24.5dBm UMTS Band V: 25dBm Supported Channel GSM system: 0.2 MHz Bandwidth UMTS system: 5 MHz Characteristics Description Designation of GSM850 249KGXW; 256KG7W Emissions GSM1900 246KGXW; 245KG7W (Remark: the necessary UMTS Band II 4M17F9W; 4M17W7D; bandwidth of which is the worst value from the measured occupied bandwidths for each UMTS Band V 4M15F9W; 4M15W7D; type of channel bandwidth configuration.)

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 9 of 21 3.8 Test Frequencies RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 128 Channel 190 Channel 251 TX 824.2MHz 836.6 MHz 848.8 MHz GSM850 Channel 128 Channel 190 Channel 251 RX 869.2 MHz 881.6 MHz 893.8 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 512 Channel 661 Channel 810 TX 1850.2MHz 1880.0 MHz 1909.8 MHz GSM1900 Channel 512 Channel 661 Channel 810 RX 1930.2 MHz 1960.0 MHz 1989.8 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 9262 Channel 9400 Channel 9538 TX WCDMA 1852.4 MHz 1880.0 MHz 1907.6 MHz Band II Channel 9662 Channel 9800 Channel 9938 RX 1932.4 MHz 1960.0 MHz 1987.6 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 4132 Channel 4182 Channel 4233 TX WCDMA 826.4MHz 836.4 MHz 846.6 MHz Band V Channel 4357 Channel 4407 Channel 4458 RX 871.4 MHz 881.4 MHz 891.6 MHz

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 10 of 21 4 Description of Tests 4.1 Conducted Output Power Measurement Procedure: FCC KDB 971168 D01 V03r01 The transmitter output was connected to a calibrated coaxial cable, attenuator and power meter, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The power output at the transmitter antenna port was determined by adding the value of the cable insertion loss to the power reading. The tests were performed at three frequencies (low channel, middle channel and high channel) and on the highest power levels, which can be setup on the transmitters. Remark: Reference test setup 1 4.2 Effective (Isotropic) Radiated Power of Transmitter Measurement Procedure: FCC KDB 971168 D01 V03r01 ; C63.26 (2015) Calculate power in dBm by the following formula: ERP (dBm) = Conducted Power (dBm) + antenna gain (dBd) EIRP(dBm) = Conducted Power (dBm) + antenna gain (dBi) EIRP=ERP+2.15dB 4.3 Occupied Bandwidth Measurement Procedure: FCC KDB 971168 D01 V03r01 Section 4.2 The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel, middle channel and high channel).The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1 percent of the selected span as is possible without being below 1 percent. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used since a peak or, peak hold, may produce a wider bandwidth than actual. The trace data points are recovered and are directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 percent of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth. Remark: Reference test setup 1

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 11 of 21 4.4 Band Edge at Antenna Terminals Measurement Procedure: FCC KDB 971168 D01 V03r01 Section 6.0 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at two frequencies (low channel and high channel).in the 1MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of 100kHz or 1% of the emission bandwidth of the fundamental emission of the transmitter may be employed. The EUT emission bandwidth is measured as the width of the signal between two points, outside of which all emission are attenuated at least 26dB below the transmitter power. The video bandwidth of the spectrum analyzer was set at thrice the resolution bandwidth. Detector Mode was set to peak or peak hold power. Remark: Reference test setup 1 4.5 Spurious And Harmonic Emissions at Antenna Terminal Measurement Procedure: FCC KDB 971168 D01 V03r01

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 12 of 21 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyzer, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. On any frequency outside a licensee’s frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB. Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. Remark: Reference test setup 1 4.6 Peak-Average Ratio Measurement Procedure: FCC KDB 971168 D01 V03r01 Section 5.7.1 A peak to average ratio measurement is performed at the conducted port of the EUT. For WCDMA signals, the spectrum analyzers Complementary Cumulative Distribution Function (CCDF) measurement profile is used to determine the largest deviation between the average and the peak power of the EUT in a given bandwidth. The CCDF curve shows how much time the peak waveform spends at or above a given average power level. The percent of time the signal spends at or above the level defines the probability for that particular power level. For GSM signals, an average and a peak trace are used on a spectrum analyzer to determine the largest deviation between the average and the peak power of the EUT in a bandwidth greater than the emission bandwidth. The traces are generated with the spectrum analyzer set to zero span mode. Remark: Reference test setup 1

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 13 of 21 4.7 Field Strength of Spurious Radiation Measurement Procedure: FCC KDB 971168 D01 V03r01 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 80cm high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) the receive antenna and by rotating through 360° the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8) Calculate power in dBm by the following formula: ERP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) Where: Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]). Above 1GHz test procedure as below: 1) Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 14 of 21 2) Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3. Test the EUT in the lowest channel, the middle channel the Highest channel 4. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5. Repeat above procedures until all frequencies measured was complete Remark: Reference test setup 3 4.8 Frequency Stability / Temperature Variation Measurement Procedure: Frequency stability testing is performed in accordance with the guidelines of FCC KDB 971168 D01 V03r01; ANSI/C63.26 (2015) . The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5 ppm ) of the center frequency. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Remark: Reference test setup 4

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 15 of 21 4.9 Test Setups 4.9.1 Test Setup 1 4.9.2 Test Setup 2 Figure 1. 30MHz to 1GHz Figure 2. above 1GHz

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 16 of 21 4.9.3 Test Setup 3 Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz 4.9.4 Test Setup 4

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 17 of 21 4.10 Test Conditions Test Case Test Conditions Test Environment Ambient Climate & Rated Voltage Average Test Setup Test Setup 1 Power, L, M, H (L= low channel, M= middle channel, H= high Total RF Channels (TX) Transmit channel ) Output Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2; Power Test Environment Ambient Climate & Rated Voltage Average Data Power, Test Setup Test Setup 1 Spectral L, M, H (L= low channel, M= middle channel, H= high Density (if RF Channels (TX) channel ) required) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2 Test Environment Ambient Climate & Rated Voltage Peak-to-Average Ratio Test Setup Test Setup 1 (if required) RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2 Test Environment Ambient Climate & Rated Voltage Modulation Test Setup Test Setup 1 Characteristics RF Channels (TX) M (M= middle channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Occupied Bandwidth RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2 Bandwidth Test Environment Ambient Climate & Rated Voltage Emission Bandwidth Test Setup Test Setup 1 (if RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) required) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2 Test Environment Ambient Climate & Rated Voltage Band Edges Test Setup Test Setup 1 Compliance RF Channels (TX) L, H (L= low channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2; Spurious Emission at Test Environment Ambient Climate & Rated Voltage

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 18 of 21 Antenna Terminals Test Setup Test Setup 1 L,M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;UMTS/TM1 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 2 GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2; Field Strength of Test Mode Remark: If applicable, the EUT conf. that has Spurious Radiation maximum power density (based on the equivalent power level) is selected. RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) (1) -30 °C to +50 °C with step 10 °C at Rated Voltage; Test Environment (2) VL, VN and VH of Rated Voltage at Ambient Climate. Frequency Stability Test Setup Test Setup 4 RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1;UMTS/TM2;

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 19 of 21 5 Main Test Instruments RE in Chamber Cal. date Cal.Due date Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic Chamber AUDIX N/A SEM001-02 2018/3/13 2021/3/12 Spectrum Analyzer (20Hz-43GHz) Rohde & Schwarz FSU43 SEM004-08 2019/3/2 2020/3/1 BiConiLog Antenna (26-3000MHz) ETS-Lindgren 3142C SEM003-01 2017/6/27 2020/6/26 Horn Antenna (800MHz-18GHz) Rohde & Schwarz HF907 SEM003-07 2018/413 2021/412 Horn Antenna (15-40GHz) Schwarzbeck BBHA 9170 SEM003-15 2017/10/17 2020/10/16 Amplifier (0.1-1300MHz) HP 8447D SEM005-02 2018/9/2 2019/9/2 Low Noise Amplifier (100MHz-18GHz) Black Diamond Series BDLNA-0118-352810 SEM005-05 2018/9/2 2019/9/2 Pre-Amplifier (0.1-26.5GHz) Compliance Directions Systems Inc. PAP-0126 EMC2063 2018/10/20 2019/10/19 Pre-amplifier (26-40GHz) Compliance Directions Systems Inc. PAP-2640-50 SEM005-08 2019/3/2 2020/3/1 Band filter N/A N/A N/A N/A N/A Measurement Software AUDIX e3 V8.2014-6-27 N/A N/A N/A Coaxial Cable SGS N/A SEM026-01 2019/6/12 2020/6/11 Wideband Radio CommunicationTeste Anristu MT8821C 6201462742 2019/4/3 2020/4/3 Wideband Radio CommunicationTester Rohde & Schwarz CMW500 W005-02 2019/1/13 2020/1/12 RF conducted test Cal. date Cal.Due date Test Equipment Manufacturer Model No. Inventory No. (yyyy-m m -dd) (yyyy-m m -dd) Dual Output Mobile Communication DC Agilent Technologies Inc 66311B W009-09 2018/11/2 2019/11/1 Source Signal Analyzer Rohde & Schwarz FSV W005-02 2019/3/2 2020/3/1 Coaxial Cable SGS N/A SEM031-01 2019/6/12 2020/6/11 Attenuator Weinschel Associates WA41 SEM021-09 N/A N/A Signal Generator KEYSIGHT N5173B SEM006-05 2018/11/2 2019/11/1 Shanghai Meteorological Industry Humidity/ Temperature Indicator HTC-1 W006-17 2018/11/2 2019/11/1 Factory Temperature Chamber GIANT FORCE ICT-150-40-CP-AR W027-03 2018/11/2 2019/11/1 Wideband Radio CommunicationTeste Anristu MT8821C 6201462742 2019/3/2 2020/3/1 Wideband Radio CommunicationTester Rohde & Schwarz CMW500 W005-02 2018/11/2 2019/11/1

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 20 of 21 Cal. Date Cal. Due Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm- date (yyyy- dd) mm-dd) 3m Semi-Anechoic Chamber AUDIX N/A SEM001-02 2018/3/13 2021/3/12 Wideband Radio CommunicationTeste Anristu MT8821C 6201462742 2019/4/3 2020/4/3 Wideband Radio CommunicationTester Rohde & Schwarz CMW500 W005-02 2019/1/13 2020/1/12 EXA Signal Analyzer (10Hz-26.5GHz) Agilent Technologies Inc N9010A SEM004-09 2019/3/13 2020/3/12 Spectrum Analyzer (20Hz-43GHz) Rohde & Schwarz FSU43 SEM004-08 2019/3/2 2020/3/1 BiConiLog Antenna (26-3000MHz) ETS-Lindgren 3142C SEM003-01 2017/6/27 2020/6/26 Horn Antenna (800MHz-18GHz) Rohde & Schwarz HF907 SEM003-07 2018/4/13 2021/4/12 Horn Antenna (15-40GHz) Schwarzbeck BBHA 9170 SEM003-15 2017/10/17 2020/10/16 Amplifier (0.1-1300MHz) HP 8447D SEM005-02 2018/9/25 2019/9/24 Compliance Directions Pre-Amplifier (0.1-26.5GHz) PAP-0126 SEM004-11 2018/9/27 2019/9/26 Systems Inc. Compliance Directions Pre-amplifier (26-40GHz) PAP-2640-50 SEM005-08 2019/3/2 2020/3/1 Systems Inc. Band filter N/A N/A N/A N/A N/A Coaxial Cable SGS N/A SEM026-01 2019/6/12 2020/6/11 Tunable Notch Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCD1700/2000-0.2/40-10EEK GMBH Tunable Notch Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCD800/960-0.2/40-10EEK GMBH HighPass Filter WAINRIGHT Instruments N/A N/A N/A N/A WHK1.2/15G-10SS GMBH HighPass Filter WAINRIGHT Instruments N/A N/A N/A N/A WHKX10-2700-3000-18000-40SS GMBH HighPass Filter WAINRIGHT Instruments N/A N/A N/A N/A WHKX7.0/26.5G-6SS GMBH Band Reject Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCG 824/849-814/859-40/8SS GMBH Band Reject Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCG 1850/1910-1835/1925-40/8SS GMBH e3 V8.2014- Measurement Software AUDIX N/A N/A N/A 6-27

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: ZR/2019/7002101 Page: 21 of 21 6 Measurement Uncertainty For a 95% confidence level (k = 2), the measurement expanded uncertainties for defined systems, in accordance with the recommendations of ISO 17025 as following: Test Item Extended Uncertainty Data Transmit Output Power Data Power [dBm] U =±0.37 dB Bandwidth Magnitude [%] U =± 0.2% Band Edge Compliance Disturbance Power [dBm] U = ±2.0 dB Spurious Emissions, Conducted Disturbance Power [dBm] U = ±2.0 dB For 3 m Chamber: U = ±4.5 dB (30 MHz to 1GHz) Field Strength of Spurious U = ±3.3 dB (above 1 GHz) ERP[dBm]/EIRP [dBm] Radiation For 10 m Chamber: U = ±4.5 dB (30 MHz to 1GHz) U = ±3.2 dB (above 1 GHz) Frequency Stability Frequency Accuracy [ppm] U = ±0.24 ppm 7 Appendixes Appendix A Photographs of EUT Constructional Details for ZR201970021 Appendix B.1 GSM 850 & 1900 Appendix B.2 WCDMA Band II & V The End


Document Created: 2019-09-09 10:41:33
Document Modified: 2019-09-09 10:41:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC