Part 90 Test Report

FCC ID: ZNFX410CS

Test Report

Download: PDF
FCCID_3890624

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com MEASUREMENT REPORT FCC Part 90 Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 4/24 - 5/9/2018 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab. Columbia, MD, USA United States Test Report Serial No.: 1M1804200078-04.ZNF FCC ID: ZNFX410CS APPLICANT: LG Electronics MobileComm U.S.A Application Type: Certification Model: LM-X410CS Additional Model(s): LMX410CS, X410CS EUT Type: Portable Handset FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) FCC Rule Part: §2.1049, §90.542, §90.543 Test Procedure(s): ANSI C63.26-2015, ANSI/TIA-603-E-2016, KDB 971168 D01 v03r01 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

T A B L E O F C O N T E N T S 1.0 INTRODUCTION ........................................................................................................................................... 4 1.1 Scope ................................................................................................................................................................. 4 1.2 PCTEST Test Location ....................................................................................................................................... 4 1.3 Test Facility / Accreditations ............................................................................................................................... 4 2.0 PRODUCT INFORMATION........................................................................................................................... 5 2.1 Equipment Description ....................................................................................................................................... 5 2.2 Device Capabilities ............................................................................................................................................. 5 2.3 Test Configuration .............................................................................................................................................. 5 2.4 EMI Suppression Device(s)/Modifications .......................................................................................................... 5 3.0 DESCRIPTION OF TESTS ........................................................................................................................... 6 3.1 Evaluation Procedure ......................................................................................................................................... 6 3.2 Radiated Power and Radiated Spurious Emissions ........................................................................................... 6 4.0 MEASUREMENT UNCERTAINTY ................................................................................................................ 7 5.0 TEST EQUIPMENT CALIBRATION DATA ................................................................................................... 8 6.0 SAMPLE CALCULATIONS ........................................................................................................................... 9 7.0 TEST RESULTS .......................................................................................................................................... 10 7.1 Summary .......................................................................................................................................................... 10 7.2 Occupied Bandwidth ........................................................................................................................................ 11 7.3 Spurious and Harmonic Emissions at Antenna Terminal ................................................................................. 14 7.4 Band Edge Emissions at Antenna Terminal ..................................................................................................... 17 7.5 Radiated Power (ERP) ..................................................................................................................................... 22 7.6 Radiated Spurious Emissions Measurements .................................................................................................. 24 7.7 Frequency Stability / Temperature Variation .................................................................................................... 27 8.0 CONCLUSION ............................................................................................................................................. 30 MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

MEASUREMENT REPORT FCC Part 90 Max. Max. Tx Frequency Emission Mode Measurement Power Power Modulation (MHz) Designator (W) (dBm) LTE Band 14 790.5 - 795.5 ERP 0.048 16.81 4M59G7D QPSK LTE Band 14 790.5 - 795.5 ERP 0.032 15.11 4M54W7D 16-QAM LTE Band 14 793 ERP 0.053 17.20 9M01G7D QPSK LTE Band 14 793 ERP 0.040 16.00 9M02W7D 16-QAM EUT Overview MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Innovation, Science and Economic Development Canada. 1.2 PCTEST Test Location These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The measurement facility is compliant with the test site requirements specified in ANSI C63.4-2014. 1.3 Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.01 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules.  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA (Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS).  PCTEST facility is a registered (2451B) test laboratory with the site description on file with ISED. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFX410CS. The test data contained in this report pertains only to the emissions due to the EUT’s licensed transmitters that operate under the provisions of Part 90. Test Device Serial No.: 00367, 00383, 00375 2.2 Device Capabilities This device contains the following capabilities: 850/1900 GPRS/EDGE, 850/1700/1900 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n WLAN, 802.11a/n/ac UNII, Bluetooth (1x, EDR, LE) 2.3 Test Configuration The EUT was tested per the guidance of ANSI/TIA-603-D-2010 and KDB 971168 D01 v03r01. See Section 7.0 of this test report for a description of the radiated and antenna port conducted emissions tests. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in the document titled “Land Mobile FM or PM – Communications Equipment – Measurements and Performance Standards” (ANSI/TIA-603-D-2010) and “Procedures for Compliance Measurement of the Fundamental Emission Power of Licensed Wideband (> 1 MHz) Digital Transmission Systems” (KDB 971168 D01 v03r01) were used in the measurement of the EUT. 3.2 Radiated Power and Radiated Spurious Emissions §2.1053, §90.542 (a. 7), §90.691 The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x 5.2m elliptical, obstruction-free area in accordance with Figure 5.7 of Clause 5 in ANSI C63.4-2014. Absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections for measurements above 1GHz. For measurements below 1GHz, the absorbers are removed. A raised turntable is used for radiated measurement. The turn table is a continuously rotatable, remote-controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm tall test table made of Styrodur is placed on top of the turn table. A Styrodur pedestal is placed on top of the test table to bring the total table height to 1.5m. The equipment under test was transmitting while connected to its integral antenna and is placed on a wooden turntable 80cm above the ground plane and 3 meters from the receive antenna. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. Radiated power levels are also investigated with the receive antenna horizontally and vertically polarized. The maximized power level is recorded using the spectrum analyzer “Channel Power” function with the integration band set to the emissions’ occupied bandwidth, a RMS detector, RBW = 100kHz, VBW = 300kHz, and a 1 second sweep time over a minimum of 10 sweeps, per the guidelines of KDB 971168 D01 v03r01. Per the guidance of ANSI/TIA-603-D-2010, a half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula: Pd [dBm] = Pg [dBm] – cable loss [dB] + antenna gain [dBd/dBi] Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]) specified in 90.691. For fundamental radiated power measurements, the guidance of KDB 971168 D01 v03r01 is used to record the EUT power level that is subsequently matched via the aforementioned substitution method given in ANSI/TIA- 603-D-2010. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

4.0 MEASUREMENT UNCERTAINTY The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.4-2014. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Contribution Expanded Uncertainty (±dB) Conducted Bench Top 1.13 Measurements Radiated Disturbance (<1GHz) 4.98 Radiated Disturbance (>1GHz) 5.07 Radiated Disturbance (>18GHz) 5.09 MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

5.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5- 2017. Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number ‐ LTx3 LIcensed Transmitter Cable Set 8/10/2017 Annual 8/10/2018 LTx3 ‐ RE1 Radiated Emissions Cable Set (UHF/EHF) 6/21/2017 Annual 6/21/2018 RE1 Agilent N9020A MXA Signal Analyzer 1/24/2018 Annual 1/24/2019 US46470561 Agilent N9030A PXA Signal Analyzer (26.5GHz) 8/28/2017 Annual 8/28/2018 MY49432391 Emco 3115 Horn Antenna (1‐18GHz) 3/28/2018 Biennial 3/28/2020 9704‐5182 ETS Lindgren 3117 1‐18 GHz DRG Horn (Medium) 12/1/2016 Biennial 12/1/2018 125518 ETS‐Lindgren 3164‐10 Quad Ridge Horn 400MHz ‐ 10000MHz 12/14/2016 Biennial 12/14/2018 166283 Keysight Technologies N9030A 3Hz‐44GHz PXA Signal Analyzer 3/20/2018 Annual 3/20/2019 MY49430494 Mini Circuits TVA‐11‐422 RF Power Amp N/A N/A QA1317001 Mini‐Circuits PWR‐SEN‐4RMS USB Power Sensor 3/30/2018 Annual 3/30/2019 11210140001 Mini‐Circuits SSG‐4000HP Synthesized Signal Generator N/A N/A 11208010032 Rohde & Schwarz CMU200 Base Station Simulator N/A 836536/0005 Rohde & Schwarz CMW500 Radio Communication Tester 11/3/2017 Annual 11/3/2018 100976 Rohde & Schwarz ESU26 EMI Test Receiver (26.5GHz) 5/19/2017 Annual 5/19/2018 100342 Rohde & Schwarz ESU40 EMI Test Receiver (40GHz) 7/31/2017 Annual 7/31/2018 100348 Rohde & Schwarz SFUNIT‐Rx Shielded Filter Unit 7/3/2017 Annual 7/3/2018 102134 Rohde & Schwarz SFUNIT‐Rx Shielded Filter Unit 7/3/2017 Annual 7/3/2018 102133 Rohde & Schwarz TS‐PR26 18‐26.5 GHz Pre‐Amplifier 5/11/2017 Annual 5/11/2018 100040 Rohde & Schwarz TS‐PR40 26.5‐40 GHz Pre‐Amplifier 5/11/2017 Annual 5/11/2018 100037 Seekonk NC‐100 Torque Wrench 5/16", 8" lbs 1/22/2018 Annual 1/22/2019 N/A Sunol DRH‐118 Horn Antenna (1‐18GHz) 8/11/2017 Biennial 8/11/2019 A050307 Sunol JB5 Bi‐Log Antenna (30M ‐ 5GHz) 4/19/2018 Biennial 4/19/2020 A051107 Table 5-1. Test Equipment Notes: 1. For equipment listed above that has a calibration date or calibration due date that falls within the test date range, care was taken to ensure that this equipment was used after the calibration date and before the calibration due date. 2. Equipment with a calibration date of “N/A” shown in this list was not used to make direct calibrated measurements. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

6.0 SAMPLE CALCULATIONS LTE Emission Designator QPSK Modulation Emission Designator = 8M62G7D LTE BW = 8.62 MHz G = Phase Modulation 7 = Quantized/Digital Info D = Data transmission, telemetry, telecommand 16QAM Modulation Emission Designator = 8M45W7D LTE BW = 8.45 MHz W = Amplitude/Angle Modulated 7 = Quantized/Digital Info D = Data transmission, telemetry, telecommand Spurious Radiated Emission – LTE Band Example: Middle Channel LTE Mode 2nd Harmonic (1564 MHz) The average spectrum analyzer reading at 3 meters with the EUT on the turntable was –81.0 dBm. The gain of the substituted antenna is 8.1 dBi. The signal generator connected to the substituted antenna terminals is adjusted to produce a reading of –81.0 dBm on the spectrum analzyer. The loss of the cable between the signal generator and the terminals of the substituted antenna is 2.0 dB at 1564 MHz. So 6.1 dB is added to the signal generator reading of –30.9 dBm yielding –24.80 dBm. The fundamental EIRP was 25.501 dBm so this harmonic was 25.501 dBm – (-24.80). MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.0 TEST RESULTS 7.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFX410CS FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) Mode(s): LTE Band: Band 14 FCC Part Test Test Test Description Test Limit Reference Section(s) Condition Result 2.1049 Occupied Bandwidth N/A PASS Section 7.2 • On all frequencies between 769-775 MHz and 799-805 MHz, attenuation by a factor not less than 65 + 10 log (P) dB in Conducted Band a 6.25 kHz band segment, for mobile and 2.1051 Sections Edge / Spurious portable stations. CONDUCTED PASS 90.543 7.3, 7.4 Emissions • On any frequency between 775-788 MHz, above 805 MHz, and below 758 MHz, attenuation by at least 43 + 10 log (P) dB. 2.1055 Frequency Stability < 2.5 ppm PASS Section 7.7 90.213 Effective Radiated 90.542 (a.7) < 3 Watts max. ERP (Band 14) PASS Section 7.5 Power (Band 14) > 43 + log10 (P[Watts]) for all out-of-band emissions except • For operations in the 758-775 MHz and 788-805 MHz bands, all emissions RADIATED Radiated Spurious 2.1053 including harmonics in the band 1559- Emissions (LTE Band PASS Section 7.6 90.543 1610 MHz shall be limited to −70 14) dBW/MHz equivalent isotropically radiated power (EIRP) for wideband signals, and −80 dBW EIRP for discrete emissions of less than 700 Hz bandwidth. Table 7-1. Summary of Test Results Notes: 1) All modes of operation and data rates were investigated. The test results shown in the following sections represent the worst case emissions. 2) The analyzer plots shown in Section 7.0 were taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables, directional couplers, and attenuators used as part of the system to maintain a link between the call box and the EUT at all frequencies of interest. 3) All antenna port conducted emissions testing was performed on a test bench with the antenna port of the EUT connected to the spectrum analyzer through calibrated cables, attenuators, and couplers. 4) For conducted spurious emissions, automated test software was used to measure emissions and capture the corresponding plots necessary to show compliance. The measurement software utilized is PCTEST “2G/3G Automation,” Version 3.9. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.2 Occupied Bandwidth §2.1049 Test Overview The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. All modes of operation were investigated and the worst case configuration results are reported in this section. Test Procedure Used KDB 971168 D01 v03r01 – Section 4.2 Test Settings 1. The signal analyzer’s automatic bandwidth measurement capability was used to perform the 99% occupied bandwidth and the 26dB bandwidth. The bandwidth measurement was not influenced by any intermediate power nulls in the fundamental emission. 2. RBW = 1 – 5% of the expected OBW 3. VBW ≥ 3 x RBW 4. Detector = Peak 5. Trace mode = max hold 6. Sweep = auto couple 7. The trace was allowed to stabilize 8. If necessary, steps 2 – 7 were repeated after changing the RBW such that it would be within 1 – 5% of the 99% occupied bandwidth observed in Step 7 Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-1. Test Instrument & Measurement Setup Test Notes None. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

LTE B14 Plot 7-1. Occupied Bandwidth Plot (LTE B14 - 5MHz QPSK – RB Size 25) Plot 7-2. Occupied Bandwidth Plot (LTE B14 - 5MHz 16-QAM – RB Size 25) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-3. Occupied Bandwidth Plot (LTE B14 - 10MHz QPSK – RB Size 50) Plot 7-4. Occupied Bandwidth Plot (LTE B14 - 10MHz 16-QAM – RB Size 50) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.3 Spurious and Harmonic Emissions at Antenna Terminal §2.1051 §90.543 Test Overview The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. All out of band emissions are measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power, and at the appropriate frequencies. All data rates were investigated to determine the worst case configuration. All modes of operation were investigated and the worst case configuration results are reported in this section. The minimum permissible attenuation level of any spurious emission is 43 + log10(P[Watts]), where P is the transmitter power in Watts. Test Procedure Used KDB 971168 D01 v03r01 – Section 6.0 Test Settings 1. Start frequency was set to 30MHz and stop frequency was set to 10GHz (separated into at least two plots per channel) 2. RBW ≥ 1MHz 3. VBW ≥ 3 x RBW 4. Detector = RMS 5. Trace mode = max hold 6. Sweep time = auto couple 7. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-2. Test Instrument & Measurement Setup MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

LTE B14 Plot 7-5. Conducted Spurious Plot (LTE B14 – 10.0MHz QPSK – RB Size 1, RB Offset 0 – Mid Channel) Plot 7-6. Conducted Spurious Plot (LTE B14 – 5100MHz QPSK – RB Size 1, RB Offset 0 – Mid Channel) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-7. Conducted Spurious Plot (LTE B14 – 10.0MHz QPSK – RB Size 1, RB Offset 0 – Mid Channel) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.4 Band Edge Emissions at Antenna Terminal §2.1051 §90.543 Test Overview All out of band emissions are measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power, and at the appropriate frequencies. All data rates were investigated to determine the worst case configuration. All modes of operation were investigated and the worst case configuration results are reported in this section. For Band 14, the minimum permissible attenuation on any frequencies between 775-788 MHz, above 805 MHz, and below 758MHz, shall be at least 43 + log10(P[Watts]). On all frequencies between 769-775 MHz and 799-805 MHz, minimum permissible attenuation shall be at least than 65 + 10 log10(P[Watts]) in a 6.25kHz band segment. Test Procedure Used KDB 971168 D01 v03r01 – Section 6.0 Test Settings 1. Span was set large enough so as to capture all out of band emissions near the band edge 2. RBW = 100 kHz 3. VBW = 300 kHz 4. Detector = RMS 5. Trace mode = trace average 6. Sweep time = auto couple 7. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-3. Test Instrument & Measurement Setup MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 17 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

LTE B14 Plot 7-8. Lower Band Edge Plot (LTE B14 - 5MHz QPSK – RB Size 25) Plot 7-9. Lower Emission Mask Band Edge Plot (LTE B14 - 5MHz QPSK – RB Size 25) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 18 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-10. Upper Band Edge Plot (LTE B14 - 5MHz QPSK – RB Size 25) Plot 7-11. Upper Emission Mask Band Edge Plot (LTE B14 - 5MHz QPSK – RB Size 25) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 19 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-12. Lower Band Edge Plot (LTE B14 - 10MHz QPSK – RB Size 50) Plot 7-13. Lower Emission Mask Band Edge Plot (LTE B14 - 10MHz QPSK – RB Size 50) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 20 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-14. Upper Band Edge Plot (LTE B14 - 10MHz QPSK – RB Size 50) Plot 7-15. Upper Emission Mask Band Edge Plot (LTE B14 - 10MHz QPSK – RB Size 50) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 21 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.5 Radiated Power (ERP) §90.542 Test Overview Effective Radiated Power (ERP) measurements are performed using the substitution method described in ANSI/TIA-603-D-2010 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using vertically and horizontally polarized tuned dipole antennas. All measurements are performed as RMS average measurements while the EUT is operating at its maximum duty cycle, at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 D01 v03r01 – Section 5.2.1 ANSI/TIA-603-D-2010 – Section 2.2.17 Test Settings 1. Radiated power measurements are performed using the signal analyzer’s “channel power” measurement capability for signals with continuous operation. 2. RBW = 1 – 5% of the expected OBW, not to exceed 1MHz 3. VBW ≥ 3 x RBW 4. Span = 1.5 times the OBW 5. No. of sweep points > 2 x span / RBW 6. Detector = RMS 7. Trigger is set to “free run” for signals with continuous operation with the sweep times set to “auto”. 8. The integration bandwidth was roughly set equal to the measured OBW of the signal for signals with continuous operation. 9. Trace mode = trace averaging (RMS) over 100 sweeps 10. The trace was allowed to stabilize MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 22 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-4. Radiated Test Setup <1GHz Test Notes 1) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case emissions are reported with the EUT positioning, modulations, RB sizes and offsets, and channel bandwidth configurations shown in the tables below. 2) This unit was tested with its standard battery. Channel Ant. Antenna Turntable Substitute Ant. ERP EIRP Frequency RB ERP ERP Margin EIRP EIRP Margin Bandwidth Mod. Pol. Height Azimuth Level Gain Limit Limit [MHz] Size/Offset [dBm] [Watts] [dB] [dBm] [Watts] [dB] [MHz] [H/V] [cm] [degree] [dBm] [dBi] [dBm] [dBm] 790.50 5 QPSK V 150 6 1/0 17.59 1.36 16.80 0.048 34.77 -17.97 18.95 0.079 36.99 -18.04 793.00 5 QPSK V 150 6 1/0 17.59 1.37 16.81 0.048 34.77 -17.96 18.96 0.079 36.99 -18.03 795.50 5 QPSK V 150 6 1 / 24 17.32 1.38 16.55 0.045 34.77 -18.22 18.70 0.074 36.99 -18.29 793.00 5 16-QAM V 150 6 1/0 15.89 1.37 15.11 0.032 34.77 -19.66 17.26 0.053 36.99 -19.73 793.00 10 QPSK V 150 1 1/0 17.98 1.37 17.20 0.053 34.77 -17.57 19.35 0.086 36.99 -17.64 793.00 10 16-QAM V 150 1 1/0 16.78 1.37 16.00 0.040 34.77 -18.77 18.15 0.065 36.99 -18.84 793.00 10 QPSK H 150 16 1/0 14.07 1.36 13.28 0.021 34.77 -21.49 15.43 0.035 36.99 -21.56 Table 7-16. ERP Data (Band 14) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 23 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.6 Radiated Spurious Emissions Measurements §2.1053 §90.543 Test Overview Radiated spurious emissions measurements are performed using the substitution method described in ANSI/TIA- 603-D-2010 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using horizontally and vertically polarized tuned dipole antennas. Measurements on signals operating above 1GHz are performed using vertically and horizontally polarized broadband horn antennas. All measurements are performed as peak measurements while the EUT is operating at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 D01 v03r01 – Section 5.8 ANSI/TIA-603-D-2010 – Section 2.2.12 Test Settings 1. RBW = 100kHz for emissions below 1GHz and 1MHz for emissions above 1GHz 2. VBW ≥ 3 x RBW 3. Span = 1.5 times the OBW 4. No. of sweep points > 2 x span / RBW 5. Detector = RMS 6. Trace mode = Average (Max Hold for pulsed emissions) 7. The trace was allowed to stabilize MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 24 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-5. Test Instrument & Measurement Setup Test Notes 1. This unit was tested with its standard battery. 2. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case setup is reported in the tables below. 3. The "-" shown in the following RSE tables are used to denote a noise floor measurement. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 25 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

OPERATING FREQUENCY: 793.00 MHz CHANNEL: 23330 MODULATION SIGNAL: QPSK BANDWIDTH: 10.0 MHz DISTANCE: 3 meters LIMIT: -13 dBm Ant. Antenna Turntable Substitute Spurious Frequency Level at Antenna Margin Pol. Height Azimuth Antenna Gain Emission Level [MHz] Terminals [dBm] [dB] [H/V] [cm] [degree] [dBi] [dBm] 2379.00 H 150 202 -49.10 4.95 -44.14 -31.1 3172.00 H - - -61.97 6.10 -55.87 -42.9 Table 7-2. Radiated Spurious Data (LTE B14 - Ch. 23330) MODULATION SIGNAL: QPSK BANDWIDTH: 10.00 MHz DISTANCE: 3 meters NARROWBAND EMISSION LIMIT: -50 dBm WIDEBAND EMISSION LIMIT: -40 dBm/MHz Ant. Antenna Turntable Substitute Spurious Frequency Level at Antenna Margin Pol. Height Azimuth Antenna Gain Emission Level [MHz] Terminals [dBm] [dB] [H/V] [cm] [degree] [dBi] [dBm] 1586.00 H 150 18 -58.92 4.62 -54.30 -14.3 Table 7-3. Radiated Spurious Data (Band 14 – 1559-1610MHz Band) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 26 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.7 Frequency Stability / Temperature Variation §2.1055 §90.539 Test Overview and Limit Frequency stability testing is performed in accordance with the guidelines of ANSI/TIA-603-D-2010. The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5 ppm) of the center frequency. Test Procedure Used ANSI/TIA-603-D-2010 Test Settings 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Test Setup The EUT was connected via an RF cable to a spectrum analyzer with the EUT placed inside an environmental chamber. Test Notes None MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 27 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

LTE B14 Frequency Stability / Temperature Variation §2.1055, §90.539 OPERATING FREQUENCY: 793,000,000 Hz CHANNEL: 23330 REFERENCE VOLTAGE: 3.85 VDC DEVIATION LIMIT: ± 0.00025 % or 2.5 ppm VOLTAGE POWER TEMP FREQUENCY Freq. Dev. Deviation o (%) (VDC) ( C) (Hz) (Hz) (%) 100 % 3.85 + 20 (Ref) 793,000,103 103 0.0000130 100 % - 30 792,999,987 -13 -0.0000016 100 % - 20 792,999,960 -40 -0.0000050 100 % - 10 793,000,114 114 0.0000144 100 % 0 792,999,934 -66 -0.0000083 100 % + 10 793,000,215 215 0.0000271 100 % + 20 793,000,434 434 0.0000547 100 % + 30 792,999,919 -81 -0.0000102 100 % + 40 793,000,025 25 0.0000032 100 % + 50 792,999,952 -48 -0.0000061 BATT. ENDPOINT 3.45 + 20 792,999,618 -382 -0.0000482 Table 7-4. LTE Band 14 Frequency Stability Data (Ch. 23330) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 28 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

LTE B14 Frequency Stability / Temperature Variation §2.1055, §90.539 Frequency Stability 3.5 2.5 1.5 Deviation (ppm) 0.5 -0.5 -1.5 -2.5 -3.5 Tem perature (°C) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 29 of 31 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

8.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFX410CS complies with all the requirements of Parts 90 of the FCC rules. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410CS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 30 of 30 1M1804200078-04.ZNF 4/24 - 5/9/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.


Document Created: 2018-06-08 13:46:22
Document Modified: 2018-06-08 13:46:22
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC