SZEM161201075001-2&3&4G

FCC ID: ZNFX230DS

Test Report

Download: PDF
FCCID_3286261

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Report No.: SZEM161201075001 Email: ee.shenzhen@sgs.com Page: 1 of 26 1 Cover page FCC REPORT Application No: SZEM1612010750RG Applicant: LG Electronics Mobile Comm USA Manufacturer: Huaqin Telecom Technology Co. Ltd. Factory: Dong Guan Huabel Electronic Technology Co.,Ltd Product Name: Mobile Handset Model No.(EUT): LG-X230ds Trade Mark: LG FCC ID: ZNFX230DS Standards: 47 CFR Part 2(2015) 47 CFR Part 22 subpart H(2015) 47 CFR Part 24 subpart E(2015) 47 CFR Part 27 subpart C(2015) Test Method: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 TIA-603-D 2010 Date of Receipt: 2016-12-18 Date of Test: 2016-12-20 to 2016-12-28 Date of Issue: 2017-01-06 Test Result: PASS * * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Authorized Signature: Derek Yang Wireless Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 2 of 26 2 Version Revision Record Version Chapter Date Modifier Remark 00 2017-01-06 Original Authorized for issue by: Tested By 2017-01-06 (Mike Hu) /Project Engineer Date Checked By 2017-01-06 (Jim Huang) /Reviewer Date “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 3 of 26 3 Test Summary FCC Test Item Requirements Test Result Verdict Rule No. §2.1046, Effective (Isotropic) §22.913, FCC: ERP ≤7 W. Section 1 of PASS Radiated Power §24.232 EIRP ≤ 2 W. Appendix B Output Data §27.50 Peak-Average §24.232 Section 2 of ≤13dB PASS Ratio §27.50 Appendix B Modulation Section 3 of §2.1047 Digital modulation PASS Characteristics Appendix B §2.1049(h), §22.917, OBW:No limit Section 4 of Bandwidth PASS §24.238 EBW: No limit Appendix B §27.53 §2.1051, ≤ -13dBm/1%*EBW, in 1 MHz Band Edge §22.917, bands immediately outside and Section 5 of adjacent to the frequency block. PASS Compliance §24.238 Appendix B §27.53 §2.1051, FCC: ≤ -13dBm/100 kHz, from 9 Spurious §22.917, kHz to 10th harmonics but Section 6 of emissions at PASS §24.238 outside authorized operating Appendix B antenna terminals frequency ranges. §27.53 §2.1051, Field strength of §22.917, Section 7 of FCC: ≤ -13dBm/100 kHz, PASS spurious radiation §24.238 Appendix B §27.53 §2.1055, Frequency §22.355, Section 8 of ≤ ±2.5ppm. PASS stability §24.235 Appendix B §27.54 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 4 of 26 4 Content Page 1 COVER PAGE ................................................................................................................................................ 1 2 VERSION ........................................................................................................................................................ 2 3 TEST SUMMARY .......................................................................................................................................... 3 4 CONTENT ...................................................................................................................................................... 4 5 GENERAL INFORMATION........................................................................................................................... 6 5.1 CLIENT INFORMATION ................................................................................................................................... 6 5.2 GENERAL DESCRIPTION OF EUT ................................................................................................................. 6 5.3 TEST MODE ................................................................................................................................................... 6 5.4 TEST ENVIRONMENT ..................................................................................................................................... 7 5.5 TEST FREQUENCY ........................................................................................................................................ 8 5.6 TEST LOCATION .......................................................................................................................................... 10 5.7 TEST FACILITY ............................................................................................................................................ 10 5.8 DEVIATION FROM STANDARDS ................................................................................................................... 10 5.9 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 10 5.10 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................ 11 5.11 TECHNICAL SPECIFICATION ........................................................................................................................ 11 6 DESCRIPTION OF TESTS ......................................................................................................................... 12 6.1 CONDUCTED OUTPUT POWER ................................................................................................................... 12 6.2 EFFECTIVE (ISOTROPIC) RADIATED POWER OF TRANSMITTER ................................................................ 12 6.3 OCCUPIED BANDWIDTH .............................................................................................................................. 13 6.4 BAND EDGE AT ANTENNA TERMINALS ....................................................................................................... 14 6.5 SPURIOUS AND HARMONIC EMISSIONS AT ANTENNA TERMINAL .............................................................. 14 6.6 PEAK-AVERAGE RATIO ............................................................................................................................... 15 6.7 FIELD STRENGTH OF SPURIOUS RADIATION .............................................................................................. 15 6.8 FREQUENCY STABILITY / TEMPERATURE VARIATION ................................................................................ 16 6.9 TEST SETUPS.............................................................................................................................................. 18 6.9.1 Test Setup 1 ......................................................................................................................................... 18 6.9.2 Test Setup 2 ......................................................................................................................................... 19 6.9.3 Test Setup 3 ......................................................................................................................................... 20 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 5 of 26 6.9.4 Test Setup 4 ......................................................................................................................................... 21 6.10 TEST CONDITIONS ...................................................................................................................................... 22 7 MAIN TEST INSTRUMENTS ...................................................................................................................... 24 8 MEASUREMENT UNCERTAINTY ............................................................................................................. 25 9 PHOTOGRAPHS - EUT CONSTRUCTIONAL DETAILS......................................................................... 26 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page Sotzs 5 General Information 5.1 Client Information #oplcant LG Hectonics Moble Gomm USA Address of Applicant 1000 Syivan Avenie Engleweed Gis. NJ oret2 Manfacurer Hysgin Talecom Technology Go. L Address o Manulectrer, No—1 Bulding.389 Keyuan Rood .Zhangjang HeTech Park, Pudong New Area, Shanghal, China Facoy Dong Guan HyabelElectonic Technoogy Go.. id Address of Factony No 2 ndistalNorthem Raad, Natonal HighTech Indusiral Development Zone. SongShan Lake, Dong Guan 5.2 General Description of EUT ProductName: Mobile Handst ModeiNo: LG—xesnds Trade Mark is Semple Tope: Porabie producton Antema Type: Loo Antoma GsMeso: o.ndBi. GsNMicod: 22zd0 Antemna Gain woonaes: ona8 tree7: o30 5.3 Test Mode Test Mode Test Modes Dascriion esvrim GSN system, GSMGARSTEGPRS, GMSH mocllaion cowive GSHM system, EGPRS. BFSHC modhtaton Cieam UMTS system. WGDVA, GPSK modlation Ciews UMTS system. WODVA, 16GAL! medulaton vremm LTE systom, G@SK modilaton tremve LTE systom, 16GANM medilation NOTE: The test modde(s] are selected accarding to relevant radio tchnology spacifeatons ~Tivedocsment in hoi o tCansoy wts Geva ConttarsotSevce nomiat ison uen o ncemite nntacantein antadat ns on d 1o necont ons drcnei in o Ted Gerncnd 1oEecwone Baeoamne m To miettd Eduen h Atarcon‘s o inInacenlo itemnfat an umacian mcnlhd non Ary REe WR Gentna anBfanTe io mt id cce t Commarya t s mte in o i ontany wa whhinie oi houn on# ary heCnany l evacnlan is o t leviant ie carvmece ttecareme oonn Rnionfom ecangnt ver in ant sotmora onPn taractorceTi counence o errevrdons n Ni whalt mttar nebal t e consary hy snaatand atemen, oget o antacon t e eaveno atmanec oie docinentisnnn oferdt m t miadand o e ul enen l ie Oe crenine mand e ts wevnin on ie ut idatytmtowsct angian remsedoris ersony®

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 7 of 26 5.4 Test Environment Environment Parameter Selected Values During Tests Relative Humidity 52% Atmospheric Pressure: 1015Pa Temperature TN 25 °C VL 3.4V Voltage : VN 3.85V VH 4.4V NOTE: VL= lower extreme test voltage VN= nominal voltage VH= upper extreme test voltage TN= normal temperature “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 8 of 26 5.5 Test Frequency RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 128 Channel 190 Channel 251 TX 824.2MHz 836.6 MHz 848.8 MHz GSM850 Channel 128 Channel 190 Channel 251 RX 869.2 MHz 881.6 MHz 893.8 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 512 Channel 661 Channel 810 TX 1850.2MHz 1880.0 MHz 1909.8 MHz GSM1900 Channel 512 Channel 661 Channel 810 RX 1930.2 MHz 1960.0 MHz 1989.8 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 4132 Channel 4182 Channel 4233 TX 826.4MHz 836.4 MHz 846.6 MHz WCDMA850 Channel 4357 Channel 4407 Channel 4458 RX 871.4 MHz 881.4 MHz 891.6 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 20775 Channel 21100 Channel 21425 TX LTE BAND 7 2502.5 MHz 2535 MHz 2567.5 MHz 5MHz Channel 2775 Channel 3100 Channel 5825 RX 2622.5 MHz 2655 MHz 2687.5 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 20800 Channel 21100 Channel 21400 TX LTE BAND 7 2505 MHz 2535 MHz 2565 MHz 10MHz Channel 2800 Channel 3100 Channel 3400 RX 2625 MHz 2655 MHz 2685 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 20825 Channel 21100 Channel 21375 TX LTE BAND 7 2507.5 MHz 2535 MHz 2562.5 MHz 15MHz Channel 2825 Channel 3100 Channel 3375 RX 2627.5 MHz 2655 MHz 2682.5 MHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 9 of 26 RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 20850 Channel 21100 Channel 21350 TX LTE BAND 7 2510 MHz 2535 MHz 2560 MHz 20MHz Channel 2850 Channel 3100 Channel 3350 RX 2630 MHz 2655 MHz 2680 MHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 10 of 26 5.6 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 5.7 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC – Registration No.: 556682 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 556682. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 5.8 Deviation from Standards None. 5.9 Abnormalities from Standard Conditions None. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 11 of 26 5.10Other Information Requested by the Customer None. 5.11 Technical Specification Characteristics Description GSM Radio System Type UMTS LTE Transmission (TX): 824 to 849 MHz GSM850 Receiving (RX): 869 to 894 MHz Transmission (TX): 1850 to 1910 MHz GSM1900 Receiving (RX): 1930 to 1990 MHz Supported Frequency Range Transmission (TX): 824 to 849 MHz UMTS band 5 Receiving (RX): 869 to 894 MHz Transmission (TX): 2500 to 2570 MHz LTE band 7 Receiving (RX): 2620 to 2690 MHz GSM850:32.5 dBm GSM1900: 30dBm Target TX Output Power UMTS band 5: 23dBm LTE band 7: 23.2dBm GSM system: 0.2 MHz Supported Channel Bandwidth UMTS system: 5 MHz LTE system 5 MHz;10 MHz;15 MHz;20 MHz Characteristics Description GSM850 245KGXW; 238KG7W Designation of Emissions GSM1900 244KGXW; 241KG7W (Note: the necessary bandwidth of UMTS band 5 4M23F9W; 4M25W7D; which is the worst value from the 4M50G7D;4M50W7D; measured occupied bandwidths for each type of channel bandwidth 8M97G7D;8M95W7D; configuration.) LTE band7 13M6G7D;13M5W7D; 18M0G7D;18M0W7D; “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 12 of 26 6 Description of Tests 6.1 Conducted Output Power Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The transmitter output was connected to a calibrated coaxial cable, attenuator and power meter, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The power output at the transmitter antenna port was determined by adding the value of the cable insertion loss to the power reading. The tests were performed at three frequencies (low channel, middle channel and high channel) and on the highest power levels, which can be setup on the transmitters. Note: Reference test setup 1 6.2 Effective (Isotropic) Radiated Power of Transmitter Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 0.8m high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m the receive antenna and by rotating through 360° the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8). Calculate power in dBm by the following formula: ERP (dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 13 of 26 Where: Pg is the generator output power into the substitution antenna. Above 1GHz test procedure as below: 1). Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2). Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3). Test the EUT in the lowest channel, the middle channel the Highest channel 4). The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5). Repeat above procedures until all frequencies measured was complete. Note: Reference test setup 2 6.3 Occupied Bandwidth Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel, middle channel and high channel).The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1 percent of the selected span as is possible without being below 1 percent. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used since a peak or, peak hold, may produce a wider bandwidth than actual. The trace data points are recovered and are directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 percent of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth. Note: Reference test setup 1 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 14 of 26 6.4 Band Edge at Antenna Terminals Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).in the 1MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of 100kHz or 1% of the emission bandwidth of the fundamental emission of the transmitter may be employed. The EUT emission bandwidth is measured as the width of the signal between two points, outside of which all emission are attenuated at least 26dB below the transmitter power. The video bandwidth of the spectrum analyzer was set at thrice the resolution bandwidth. Detector Mode was set to peak or peak hold power. Note: Reference test setup 1 6.5 Spurious And Harmonic Emissions at Antenna Terminal Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyzer, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. On any frequency outside a licensee’s frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB. Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. Note: Reference test setup 1 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 15 of 26 6.6 Peak-Average Ratio Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 A peak to average ratio measurement is performed at the conducted port of the EUT. For WCDMA signals, the spectrum analyzers Complementary Cumulative Distribution Function (CCDF) measurement profile is used to determine the largest deviation between the average and the peak power of the EUT in a given bandwidth. The CCDF curve shows how much time the peak waveform spends at or above a given average power level. The percent of time the signal spends at or above the level defines the probability for that particular power level. For GSM signals, an average and a peak trace are used on a spectrum analyzer to determine the largest deviation between the average and the peak power of the EUT in a bandwidth greater than the emission bandwidth. The traces are generated with the spectrum analyzer set to zero span mode. Note: Reference test setup 1 6.7 Field Strength of Spurious Radiation Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 80cm high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) the receive antenna and by rotating through 360° the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 16 of 26 8) Calculate power in dBm by the following formula: ERP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) Where: Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]). Above 1GHz test procedure as below: 1) Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2) Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3. Test the EUT in the lowest channel, the middle channel the Highest channel 4. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5. Repeat above procedures until all frequencies measured was complete Note: Reference test setup 3 6.8 Frequency Stability / Temperature Variation Measurement Procedure: Frequency stability testing is performed in accordance with the guidelines of FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 . The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 17 of 26 ±0.00025% (±2.5 ppm ) of the center frequency. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Note: Reference test setup 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 18 of 26 6.9 Test Setups 6.9.1 Test Setup 1 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 19 of 26 6.9.2 Test Setup 2 Figure 1. 30MHz to 1GHz Figure 2. above 1GHz Figure 1. 30MHz to 1GHz Figure 2. above 1GHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 20 of 26 6.9.3 Test Setup 3 Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 21 of 26 6.9.4 Test Setup 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 22 of 26 6.10 Test Conditions Test Case Test Conditions Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Average Power, Total RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Transmit GSM/TM1;GSM/TM2;UMTS/TM1; Output Test Mode UMTS/TM2;LTE/TM1;LTE/TM2 Power Data Test Environment Ambient Climate & Rated Voltage Average Power, Test Setup Test Setup 1 Spectral Density RF Channels (TX) L, M, H (if required) (L= low channel, M= middle channel, H= high channel ) GSM/TM1;GSM/TM2;UMTS/TM1; Test Mode UMTS/TM2;LTE/TM1;LTE/TM2 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Peak-to-Average Ratio L, M, H RF Channels (TX) (if required) (L= low channel, M= middle channel, H= high channel ) GSM/TM1;GSM/TM2;UMTS/TM1; Test Mode UMTS/TM2;LTE/TM1;LTE/TM2 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Modulation Characteristics M RF Channels (TX) (M= middle channe ) GSM/TM1;GSM/TM2;UMTS/TM1; Test Mode UMTS/TM2;LTE/TM1;LTE/TM2 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Occupied Bandwidth L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) GSM/TM1;GSM/TM2;UMTS/TM1; Test Mode Bandwidth UMTS/TM2;LTE/TM1;LTE/TM2 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Emission Bandwidth L, M, H RF Channels (TX) (if required) (L= low channel, M= middle channel, H= high channel ) GSM/TM1;GSM/TM2;UMTS/TM1; Test Mode UMTS/TM2;LTE/TM1;LTE/TM2 Test Environment Ambient Climate & Rated Voltage Band Edges Compliance Test Setup Test Setup 1 RF Channels (TX) L, H “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 23 of 26 (L= low channel, H= high channel ) GSM/TM1;GSM/TM2;UMTS/TM1; Test Mode UMTS/TM2;LTE/TM1;LTE/TM2 Test Environment Ambient Climate & Rated Voltage Spurious Emission at Antenna Test Setup Test Setup 1 Terminals L,M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;UMTS/TM1;LTE/TM1 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 2 Field Strength of Spurious GSM/TM1; GSM/TM2;UMTS/TM1; UMTS/TM2;LTE/TM1; Radiation LTE/TM2; NOTE: If applicable, the EUT conf. that has Test Mode maximum power density (based on the equivalent power level) is selected. L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) (1) -30 °C to +50 °C with step 10 °C at Rated Voltage; Test Env. (2) VL, VN and VH of Rated Voltage at Ambient Climate. Test Setup Test Setup 4 Frequency Stability L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) GSM/TM1;GSM/TM2;UMTS/TM1; Test Mode UMTS/TM2;LTE/TM1;LTE/TM2 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 24 of 26 7 Main Test Instruments RE in Chamber Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic 1 ETS-LINDGREN N/A SEM001-01 2016-05-13 2017-05-13 Chamber Agilent 2 EMI Test Receiver N9038A SEM004-05 2017-09-16 2017-09-16 Technologies BiConiLog Antenna 3 ETS-LINDGREN 3142C SEM003-02 2014-11-15 2017-11-15 (26-3000MHz) Double-ridged horn 4 ETS-LINDGREN 3117 SEM003-11 2015-10-17 2018-10-17 (1-18GHz) Horn Antenna (18- 5 ETS-LINDGREN 3160 SEM003-12 2014-11-24 2017-11-24 26GHz) Pre-amplifier (0.1- Agilent 6 8447D SEM005-01 2016-04-25 2017-04-25 1300MHz) Technologies Compliance Pre-Amplifier (0.1- 7 Directions Systems PAP-0126 SEM004-10 2016-10-17 2017-10-17 26.5GHz) Inc. 8 Band filter Amindeon 82346 SEM023-01 N/A N/A Universal radio 9 communication Rohde & Schwarz CMU200 SEM010-01 2016-10-23 2017-10-23 tester Universal radio 10 communication Rohde & Schwarz CMW500 SEM010-03 2016-10-23 2017-10-23 tester RXN- 11 DC Power Supply Zhao Xin SEM011-02 2016-10-09 2017-10-09 305D BiConiLog Antenna 12 Schwarzbeck VULB9163 SEM003-05 2015-10-17 2018-10-17 (30MHz-3GHz) Horn Antenna 13 Rohde & Schwarz HF907 SEM003-06 2015-06-14 2018-06-14 (800MHz-18GHz) “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 25 of 26 RF connected test Inventory Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) 1 Humi/ Temp Indicator MingGao TH101B W006-09 2016-03-09 2017-03-09 2 Spectrum Analyzer Rohde & Schwarz FSP SEL0154 2016-10-17 2017-10-17 3 MXA Signal Analyzer Agilent N9020A W025-01 2016-07-18 2017-07-18 4 Barometer ChangChun DYM3 SEL0088 2016-05-24 2017-05-24 Dual Output Mobile Agilent 5 Communication DC 66319D W009-02 2016-07-23 2017-07-23 Technologies Inc Source 6 Digital Multimeter Fluke 15B+ W055-01 2016-03-09 2017-03-09 Wireless 7 Communications Test Rohde & Schwarz CMW500 W005-03 2016-03-08 2017-03-08 Set Universal Radio 8 Communication R&S CMU200 W005-01 2016-10-23 2017-10-23 Tester 8 Measurement Uncertainty For a 95% confidence level (k = 2), the measurement expanded uncertainties for defined systems, in accordance with the recommendations of ISO 17025 as following: Test Item Extended Uncertainty Data Transmit Output Power Data Power [dBm] U = 0.37 dB Bandwidth Magnitude [%] U = 0.2% Band Edge Compliance Disturbance Power [dBm] U = 2.0 dB Spurious Emissions, Conducted Disturbance Power [dBm] U = 2.0 dB Field Strength of Spurious ERP [dBm] For 3 m Chamber: Radiation U = 4.5 dB (30 MHz to 1GHz) U = 3.3 dB (above 1 GHz) For 10 m Chamber: U = 4.5 dB (30 MHz to 1GHz) U = 3.2 dB (above 1 GHz) Frequency Stability Frequency Accuracy [ppm] U = 0.24 ppm “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201075001 Page: 26 of 26 9 Photographs - EUT Constructional Details Refer to Appendix A - Photographs of EUT Constructional Details for SZEM1612010750RG. The End “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”


Document Created: 2017-02-09 12:12:30
Document Modified: 2017-02-09 12:12:30
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC