LG-X220dsh_TestRpt_RFExp Part 2

FCC ID: ZNFX220DSH

RF Exposure Info

Download: PDF
FCCID_2929607

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner S ,. Service suisse d'6talonnage Engineering AG r' Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Galibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation Ho.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates crienr Spofton-KS (Auden)

Schweizerischer Kalibrierdienst Service suisse d‘étalonnage Servizio svizzero di taratura Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: DB35V2—40091_Nov15 Page 2 of 8

DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 835 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.5 0.90 mho/m Measured Head TSL parameters (22.0 £0.2) °C 42.6 £ 6 % 0.92 mho/m x 6 % Head TSL temperature change during test <0.5 °C —— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 2.91 Whkg SAR for nominal Head TSL parameters normalized to 1W 9.14 Wikg 2 17.0 % (k=2) SAR averaged over 10 cm(10 g) of Head TSL condition SAR measured 250 mW input power 1.50 Wig SAR for nominal Head TSL parameters normalized to 1W 5.94 Wikg 2 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 55.2 0.97 mho/m Measured Body TSL parameters (22.0 £0.2) °C 55.6 16 % 0.99 mho/m + 6 % Body TSL temperature change during test <0.5°C —— SAR result with Body TSL SAR averaged over 1 cm° (1 g) of Body TSL Condition SAR measured 250 mW input power 2.42 Wikg SAR for nominal Body TSL parameters normalized to 1W 9.55 Wikg x 17.0 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL condition SAR measured 250 mW input power 1.59 Wig SAR for nominal Body TSL parameters normalized to 1W 6.29 Wikg 2 16.5 % (k=2) Certificate No: DB35V2—40091_Nov15 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL lmpedance, transformed to feed point 51.3O-4.3jC) Return Loss

DASY5 Validation Report for Head TSL Date: 24.11.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 40091 Communication System: UID 0 — CW; Frequency: 835 MHz Medium parameters used: £ = 835 MHz; o = 0.92 S/m; & = 42.6; p = 1000 kg/m? Phantom section: Flat Section Measurement Standard: DASY3 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: Probe: EX3DV4 — SN7349; ConyF(9.77, 9.77, 9.77); Calibrated: 30.12.2014; Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 17.08.2015 Phantom: Flat Phantom 4.9L; Type: QDOOOP49AA; Serial: 1001 DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Head Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=5mm, dz=5mm Reference Value = 60.87 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 3.43 W/kg SAR(I g) = 2.31 W/kg; SAR(10 g) = 1.5 W/kg Maximum value of SAR (measured) =3.05 W/kg 1e 0 dB =3.05 W/kg = 4.84 dB W/kg Certificate No: DB35V2—40091_Nov15 Page 5 of 8

24 Nov 2015 15:46:17 CHJ s1i 1 U FS 1: 51.328 & —4.3398 n 43.920 pF §35.000 00d MHz po Del Ca A¥g 16 H1d CH2 CaA Aw 16 H1d START 635.000 000 MHz STOP 1 035.000 000 MHz Certificate No: D835V2—4d091_Nov15 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 24.11.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 40091 Communication System: UID 0 — CW; Frequency: 835 MHz Medium parameters used: £ = 835 MHz; 0 = 0.99 $/m; & = 55.6; p = 1000 kg/m? Phantom section: Flat Section Measurement Standard: DASYS (IEEEAEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(9.72, 9.72, 9.72); Calibrated: 30.12.2014; * Sensor—Surface; 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 $n601; Calibrated: 17.08.2015 + Phantom: Flat Phantom 4.9L; Type: QDOOOP49AA; Serial: 1001 «_ DASY32 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Body Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=5mm, dz=5mm Reference Value = 59.69 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 3.58 W/kg SAR(I g) = 2.42 W/kg:; SAR(10 g) = 1.59 W/kg Maximum value of SAR (measured) = 3.19 W/kg uss 0 dB =3.19 W/kg = 5.04 dBW/kg Certificate No: DB35V2—40091_Nov15 Page 7 of 8

24 Now 2015 11144153 CH #11 4 L FS 1: 47.342 a —6.3320 m 30.102 pF 835.000 Agd MHz eC_ Pag *~, L. * * * * _ h — _ &3 A_\" Del CA CH2 CaA Aw 159 H1d START 635.000 000 MHz STOP 1 ©35.000 000 MHz Certificate No: D835V2—4d091_Nov15 Page 8 of 8

Calibration Laboratory of SchweizerischerKalibrierdienst S Schmid & Partner ,. Service suisse d'6talonnage Engineering AG \' Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Acqeditation tlo.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certilicates crient Sporton-KS (Auden)

Calibration Laboratory of Schmid & Paftner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland Accredited by the Swiss Accreditation Service (SAS) The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for lhe recognition of calibration ceriificates Glossary: TSL ConvF N/A

DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 1900 MHz a 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.0 1.40 mho/m Measured Head TSL parameters (22.0 £0.2) °C 89.4 £ 6 % 1.39 mho/m 2 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 9.85 Wikg SAR for nominal Head TSL parameters normalized to 1W 39.4 Wikg x 17.0 % (k=2) SAR averaged over 10 cm? (10 g) of Head TSL condition SAR measured 250 mW input power 5.15 Wikg SAR for nominal Head TSL parameters normalized to 1W 20.6 Wikg x 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mho/m Measured Body TSL parameters (22.0 £0.2) °C 52.2 26 % 1.52 mho/m 2 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 10.2 Wikg SAR for nominal Body TSL parameters normalized to 1W 40.6 Wikg x 17.0 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL condition SAR measured 250 mW input power 5.36 Wkg SAR for nominal Body TSL parameters normalized to 1W 21.4 Wikg 2 16.5 % (k=2) Certificate No: D1900V2—5d118_Nov15 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL lmpedance, transformed to feed point 51.8O +7.2ja Return Loss

DASYS Validation Report for Head TSL Date:23.11.2015 Test Laboratory: SPEAG, Zuich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 - SN: 5d118 Communication System: UID 0 - CW; Frequency: 1900 MHz Medium parameters used: f = 1900 MHz; o = 1.39 S/m; e. = 39.4;P = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63 .19 -201 l) DASY52 Configuration: . Probe: EX3DV4 - SN7349; ConvF(S.14,8.14,8.14); Calibrated: 30.12.2014; . Sensor-Surface: 1.4mm (Mechanical Surface Detection) . Electronics: DAE4 Sn601; Calibrated: I7.08.2015 . Phantom: Flat Phantom 5.0 (front); Type: QD000P50AA; Serial: 1001 . DASY52 52.8.8(1222); SEMCAD x 14.6.t0(733r) Dipole Calibration for Head Tissue/Pin=250 mW, d-l0mmlZoom Scan (7x7x7)lCube 0: Measurement grid: dx=5mm, dy=Smm, dz=5mm Reference Value = 107.5 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 13.5 W&g SAR(I 8) = 9.85 Wkg; SAR(10 8) = 5.15 Wkg Maximum value of SAR (measured) = 15.1 Wkg 0 dB = 15.1 Wkg = 11.79 dBWkg

23 Nov 2015 16:02:12 [CHI) Ss11 1 U OFS 1i 51.795 & 7.1895 4 602.23 pH 1 900.000 dao MHz r—p—— De l C Av q 16 H1 d CH2 Del CaA Av 169 H1d START 1 700.000 ado MHz STOP 2 100.000 000 MHz Certificate No: D1900V2—5d118_Nov15 Page 6 of 8

DASYS Validation Report for Body TSL Date:23.11.2015 Test Laboratory: SPEAG, Zunch, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 - SN: 5d118 Communication System: UID 0 - CW; Frequency: 1900 MHz Mediumparametersused: f = 1900MHz; o=1.52 S/m; e. =52.2; p = 1000kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63 .T9 -201 1) DASY52 Configuration: . Probe: EX3DV4 - SN7349; ConvF(7.9,7.9,7.9); Calibrated: 30.12.2014; . Sensor-Surface: 1.4mm (Mechanical Surface Detection) . Electronics: DAE4 Sn601; Calibrated: 17.08.2015 . Phantom: Flat Phantom 5.0 (back); Type: QD000P50AA; Serial: 1002 . DASY5Z 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Body Tissue/Pin=250 mW, d=l0mmlZoom Scan (7x7x7YCube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 105.1 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 18.3 Wkg SAR(1 B) = 10.2 Wkg; SAR(10 8) = 5.36 Wkg Maximum value of SAR (measured) = 15.5 Wkg

23 Nov 2015 16:01:49 CHJ s1i £ UOFS 1: 47.791 & 7.7031 a 645.26 pH 1 900.000 000 MHz C **_ A $ w > % 5 Fa :F’ C ’\ / 2 / % % Del ',-f y § ¥ & ’5 ~— _ ’}\\ /£ $oCk . 03 . C3 A Ca { 1 V k ~ . L | ~ > * '- ?" _ \ | ;, T 2 k s9 \ * teg # fAvg % «/ * 6*~ & — /4 16° *% * . C \ / % & '\\—‘{ u2" 4 7 H1d CH2 Del CA Aw 159 H1d START 1 700.000 ddo MHz STOP 2 100.000 ooo MHz Certificate No: D1900V2—5d118_Nov15 Page 8 of 8

Calibration Laboratory of S SchweizerischerKalibrierdienst Schmid & Partner A Service suisse d'6talonnage ts Servizio svizzero di taratura Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation tlo.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration cedificates crient Sporton-KS (Auden)

Schweizerischer Kalibrierdienst S Service suisse d‘étalonnage C Servizio svizzero di taratura S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—840_Nov15 Page 2 of 8


Document Created: 2017-11-20 16:52:02
Document Modified: 2017-11-20 16:52:02
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC