Test Report-JBP

FCC ID: ZNFX210LMW

Test Report

Download: PDF
FCCID_4370810

FCC TEST REPORT Prepared for : LG Electronics USA, Inc. 1000 Sylvan Ave. Englewood Cliffs, New Jersey, United States 07632 FCC ID: ZNFX210LMW Product: 4G Mobile phone Trade Name: LG Model Name: LM-X210LMW Date of Test: Jun 25, 2019 ~ July 11, 2019 Date of Report: July 11, 2019 Report Number: HK1907111626-8E Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Heping Community, Fuhai Street, Bao'an District, Shenzhen, China TEL: +86-755-2302 9901 FAX: +86-755-2302 9901 E-mail: service@cer-mark.com http://www.cer-mark.com

Page 2 of 20 Report No.: HK1907111626-8E TEST REPORT VERIFICATION Applicant : LG Electronics USA, Inc. Address : 1000 Sylvan Ave. Englewood Cliffs, New Jersey, United States 07632 Manufacturer : OPTIEMUS ELECTRONICS LIMITED Address : D-348, Sector 63, Gautam Budh Nagar, Noida, Uttar Pradesh 201307 India EUT Description : 4G Mobile phone (A) Model No. : LM-X210LMW (B) Serial No. : N/A (C) Power Supply : DC3.85V By Battery or DC5V from adapter FCC Part 15 Subpart B Standards ........................ ANSI C63.4:2014 This device described above has been tested by HUAK, and the test results show that the equipment under test (EUT) is in compliance with Part 15 of FCC Rules. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of HUAK, this document may be altered or revised by HUAK, personal only, and shall be noted in the revision of the document. Date of Test....................................... Date (s) of performance of tests ........ Jun 25, 2019 ~ July 11, 2019 Date of Issue ..................................... July 11, 2019 Test Result ......................................... Pass Testing Engineer : (Gary Qian) Technical Manager : (Eden Hu) Authorized Signatory : (Jason Zhou) Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 3 of 20 Report No.: HK1907111626-8E 1 . TEST SUMMARY 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 DESCRIPTION OF TEST SETUP 8 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 8 2.5 MEASUREMENT INSTRUMENTS LIST 9 3 . EMC EMISSION TEST 10 3.1 CONDUCTED EMISSION MEASUREMENT 10 3.1.1 POWER LINE CONDUCTED EMISSION 10 3.1.2 TEST PROCEDURE 11 3.1.3 TEST SETUP 11 3.1.4 EUT OPERATING CONDITIONS 11 3.1.5 TEST RESULTS 12 3.2 RADIATED EMISSION MEASUREMENT 14 3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT 14 3.2.2 TEST PROCEDURE 14 3.2.3 TEST SETUP 15 3.2.4 EUT OPERATING CONDITIONS 15 3.2.5 TEST RESULTS 16 3.2.6 TEST RESULTS(Above 1GHz) 18 4 . EUT TEST PHOTO 19 5. PHOTOS OF THE EUT 20 Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 4 of 20 Report No.: HK1907111626-8E 1. TEST SUMMARY Test procedures according to the technical standards: EMC Emission Standard Test Item Limit Judgment Remark Conducted Emission Class B PASS FCC Part 15 Subpart B ANSI C63.4:2014 Radiated Emission Class B PASS NOTE: (1) ’N/A’ denotes test is not applicable in this Test Report (2) For client’s request and manual description, the test will not be executed. Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 5 of 20 Report No.: HK1907111626-8E 1.1 TEST FACILITY Test Firm : Shenzhen HUAK Testing Technology Co., Ltd. Address : 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Fuhai Street, Bao'an District, Shenzhen City, China Designation Number : CN1229 Test Firm Registration Number:616276 IC Registration No.: 21210 The 3m alternate test site of Shenzhen HUAK Testing Technology Co., Ltd. EMC Laboratory has been registered by Certification and Engineer Bureau of Industry Canada for the performance of with Registration No.: 21210 on May 24, 2016. 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %. Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.08dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz) = 4.42dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.06dB, k=2 Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 6 of 20 Report No.: HK1907111626-8E 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment 4G Mobile phone Model Name LM-X210LMW Serial No N/A Model Difference N/A The EUT is a 4G Mobile phone Operating frequency: N/A Connecting I/O port: N/A Product Description Based on the application, features, or specification exhibited in User's Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the User's Manual. Power Source AC Voltage Power Rating DC3.85V By Battery or DC5V from adapter Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 7 of 20 Report No.: HK1907111626-8E 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 Running For Conducted Test Final Test Mode Description Mode 1 Running For Radiated Test Final Test Mode Description Mode 1 Running Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 8 of 20 Report No.: HK1907111626-8E 2.3 DESCRIPTION OF TEST SETUP AC Plug Adapter E-1 EUT 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Series No. Note E-1 4G Mobile phone LG LM-X210LMW N/A EUT Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 9 of 20 Report No.: HK1907111626-8E 2.5 MEASUREMENT INSTRUMENTS LIST Cal. Item Equipment Manufacturer Model No. Serial No. Last Cal. Interval L.I.S.N. 1. Artificial Mains R&S ENV216 HKE-002 Dec. 27, 2018 1 Year Network 2. Receiver R&S ESCI 7 HKE-010 Dec. 27, 2018 1 Year RF automatic 3. Tonscend JS0806-2 HKE-060 Dec. 27, 2018 1 Year control unit 4. Spectrum analyzer R&S FSP40 HKE-025 Dec. 27, 2018 1 Year 5. Spectrum analyzer Agilent N9020A HKE-048 Dec. 27, 2018 1 Year 6. Preamplifier Schwarzbeck BBV 9743 HKE-006 Dec. 27, 2018 1 Year 7. EMI Test Receiver Rohde & Schwarz ESCI 7 HKE-010 Dec. 27, 2018 1 Year Bilog Broadband 8. Schwarzbeck VULB9163 HKE-012 Dec. 27, 2018 1 Year Antenna FMZB 1519 9. Loop Antenna Schwarzbeck HKE-014 Dec. 27, 2018 1 Year B 10. Horn Antenna Schewarzbeck 9120D HKE-013 Dec. 27, 2018 1 Year EMC05184 11. Pre-amplifier EMCI HKE-015 Dec. 27, 2018 1 Year 5SE 12. Pre-amplifier Agilent 83051A HKE-016 Dec. 27, 2018 1 Year EMI Test Software JS1120-B 13. Tonscend HKE-083 Dec. 27, 2018 N/A EZ-EMC Version 14. Power Sensor Agilent E9300A HKE-086 Dec. 27, 2018 1 Year 15. Spectrum analyzer Agilent N9020A HKE-048 Dec. 27, 2018 1 Year 16. Signal generator Agilent N5182A HKE-029 Dec. 27, 2018 1 Year 17. Signal Generator Agilent 83630A HKE-028 Dec. 27, 2018 1 Year 18. Shielded room Shiel Hong 4*3*3 HKE-039 Dec. 27, 2018 3 Year Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 10 of 20 Report No.: HK1907111626-8E 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION (Frequency Range 150KHz-30MHz) Class A (dBuV) Class B (dBuV) FREQUENCY (MHz) Quasi-peak Average Quasi-peak Average 0.15 -0.5 79.00 66.00 66 - 56 * 56 - 46 * 0.50 -5.0 73.00 60.00 56.00 46.00 5.0 -30.0 73.00 60.00 60.00 50.00 Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 11 of 20 Report No.: HK1907111626-8E 3.1.2 TEST PROCEDURE a. The EUT was placed 0.4 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.1.3 TEST SETUP 3.1.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing. Remark: We tested AC 120V/60Hz and AC 240V/60Hz, the worst case was recorded. Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 12 of 20 Report No.: HK1907111626-8E 3.1.5 TEST RESULTS EUT： 4G Mobile phone Model Name. ： LM-X210LMW Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Test Date : 2019-07-11 Test Mode： Running Phase : L Test Voltage ： AC120V/60Hz Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 13 of 20 Report No.: HK1907111626-8E EUT： 4G Mobile phone Model Name. ： LM-X210LMW Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Test Date : 2019-07-11 Test Mode： Running Phase : N Test Voltage ： AC120V/60Hz Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 14 of 20 Report No.: HK1907111626-8E 3.2 RADIATED EMISSION MEASUREMENT 3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Class A (at 10m) Class B (at 3m) FREQUENCY (MHz) dBuV/m dBuV/m 30 ~ 88 39.0 40.0 88 ~ 216 43.5 43.5 216 ~ 960 46.5 46.0 Above 960 49.5 54.0 Notes: (1) The limit for radiated test was performed according to as following: FCC PART 15B /ICES-003. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20log Emission level (uV/m). 3.2.2 TEST PROCEDURE a. The measuring distance of at 10 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1GHz, any suitable measuring distance may be used. b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. c. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured, above 1G Average detector mode will be instead. e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP(AV) Limits and then no additional QP Mode measurement performed. f. For the actual test configuration, please refer to the related Item –EUT Test Photos. Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 15 of 20 Report No.: HK1907111626-8E 3.2.3 TEST SETUP (A) Radiated Emission Test Set-Up Frequency Below 1 GHz (B) Radiated Emission Test Set-Up Frequency Above 1GHz 3.2.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing. Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 16 of 20 Report No.: HK1907111626-8E 3.2.5 TEST RESULTS EUT： 4G Mobile phone Model Name ： LM-X210LMW Temperature： 24 ℃ Relative Humidity： 54% Pressure： 1010 hPa Test Date : 2019-07-11 Test Mode ： Running Polarization : Horizontal Test Power ： AC120V/60Hz Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 17 of 20 Report No.: HK1907111626-8E EUT： 4G Mobile phone Model Name ： LM-X210LMW Temperature： 24 ℃ Relative Humidity： 54% Pressure： 1010 hPa Test Date : 2019-07-11 Test Mode ： Running Polarization : Vertical Test Power ： AC120V/60Hz Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 18 of 20 Report No.: HK1907111626-8E 3.2.6 TEST RESULTS(Above 1GHz) EUT： 4G Mobile phone Model Name ： LM-X210LMW Temperature： 24 ℃ Relative Humidity： 54% Pressure： 1010 hPa Test Date : N/A Test Mode ： N/A Test Power ： N/A Note: 1) N/A - denotes test is not applicable in this test report 2) There was not any unintentional transmission in standby mode Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 19 of 20 Report No.: HK1907111626-8E 4. EUT TEST PHOTO Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report

Page 20 of 20 Report No.: HK1907111626-8E 5. PHOTOS OF THE EUT Reference to the reporter : ANNEX A of external photos and ANNEX B of internal photos -------------------End of report------------------- Shenzhen HUAK Testing Technology Co., Ltd. FCC Test Report


Document Created: 2019-07-24 21:41:15
Document Modified: 2019-07-24 21:41:15
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC