I17Z62297-SEM01_SAR_Rev3 Part3

FCC ID: ZNFX210FM

RF Exposure Info

Download: PDF
FCCID_3771649

TTL 1 TTL in Collaboration with a Add: No.S1 Xueyuan Road, Haidian Distict, Bljng, 100191, China Tel:+86—10—62304633—2218 Faxc +86—10—0230463302200 E—mail: ctl@chinatt.com nifiwichinat en Glossary: TSL tissue simulating liquid NORMxy.z sensitivityin free space ConvE sensitivity in TSL / NORMx.yz DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal AB,C,D modulation dependent linearzation parameters Polarization © © rotation around probe axis Polarization 0 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), i 8=0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques‘, June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)®, February 2005 ) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the humen body (frequency range of 30 MHz to 6 GHz)®, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: * NORMxy,z: Assessed for E—field polarization 6=0 (fs900MHz in TEM—cell 1:> 1800MHz: waveguide). NORMx,y,z are only intermediate values, ie., the uncertainties of NORMx,y,z does not effect the E field uncertainty inside TSL (see below ConvF). * NORM(Mxy,z = NORMxy,z* frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency responseis included in the stated uncertainty of ConvF. * DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep (no uncertainty required). DCP does not depend on frequency nor media. * PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics. * Auy.zBuyz; Coy,2;VRuy.zAB.C are numerical lingarization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltageacross the diode. * ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for s800MHz) and inside waveguide using analytical feld dlistributions based on power measurements for f »800MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty valued are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z" ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent Conve is used in DASY version 4.4 and higher which allows extending the validity from:50MHztox100MHz. * Spherical isotropy (3D deviation from isotropy); in a field of low gradients realized using a flat phantom exposed by a patch antenna. «_ Sensor Offset: The sensoroffset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. * Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: Z16—9725 1 Page 2 of 11

in Collaboration with TrL CauBRATION a LazoRArORY Add: No.51 Xueywian Road, Haidian Distict, Beffng, 100191, China Tel: +86—10—62300633—2218 Fmc +86—10—62304633—02200 E—mail: ctl@chinatl.com Hipo/wwwrchinatlen Probe EX3DV4 SN: 3846 Calibrated: January 13, 2017 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: Z16—97251 Page 3 of 11

Add:No 51 Xueyuan Road, Haidian Distict, Bing, 100191, China Tels +86—10—62304633—2218 Pno+86—10—62304633—2200 E—mail: ctl@chinatl.com Hitpo/wwuchinat DASY/EASY — Parameters of Probe: EX3DV4 — SN: 3846 Basic Calibration Parameters Sensor X Sensor Y Sensor 2 Une (k=2) Norm(gVi(Vim)®) 0.39 0.47 0.47 £10.8% DGP(mV)° 99.4 se.9 so.6 Modulation Calibration Parameters uin Communication A B 6 p vR Unc® System Name dB dB—pV dB mV (k=2) 0 cw x _|0.0 0.0 1.0 0.00 175.0 22.1% Y 0.0 0.0 1.0 188.3 2 0.0 0.0 1.0 190.7 The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X, Y, Z do not affect the E*—field uncertainty inside TSL (see Page 5 and Page 6) * Numericallinearization parameter: uncertainty not required. © Uncertainly is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: Z16—97251 Page 4 of 11

TL I ‘T./ in Colaboration with Add: No.S1 Xueysan Road, Haidian Distict, Beiing, 100191, China Tels +86—10—42304633—2218 Fac +86—104230403—2200 E—mail: ctl@chinatt.com Hitpshonwcchinathn DASY/EASY — Parameters of Probe: EX3DV4 — SN: 3846 Calibration Parameter Determined in Head Tissue Simulating Media s Auron Pe:::v";y . c°“"(;’°:')':'y ConvF X ConvF ¥ ConvF Z Alpha® D(:":', :‘::; Tso 419 ose wes ass es 030 o70_| £12% 200 a15 o.97 ase oss ess oi6 127 £12% 1450 405 120 s42 s42 s42 o2s 092 £12% T750 401 137 ais _|_a16_|_a16_| 022 109| £12% 1900 400 140 Tee 18e 18e 023 114 +12% 2100 so8 149 Teo 1so 1so 020 118 +12% 2300 se5 167 Tas 145 14s oss on £12% 2450 302 1.80 Taa 122 122 oas 087 +12% 2600 se 196 Tiz 112 112 os2 080 £12% s250 359 an aar sar _|_s3r_| 045 115| £13% 5600 355 5.07 4.72 4.72 4.72 0.45 1.30 £13% s750 354 522 a9s 4ss 495 o4s_| 140 £13% © Frequency validity above 300 Mz of +100MHz only applies for DASY v4.4 and higher (Page 2), else it is restrcted to #50MHz. The uncertainty is the RSS of Convr uncertainty at calibration frequency and the uncertainty forthe indicated frequency band. Frequency validty below 300 MHz is + 10, 25, 40, 50 and 70 MHz for Conv assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to £ 110 MHz. "Atfrequency below 3 GHz, the validity of issue paramaters (e and 0) can be relaxed to £10% if liquid compensation formula is applied to measured SAR values. Atfrequencies above 3 GHz, the validty of lissue parameters (e and 0) is restricted to £5%. The uncertainty is the RSS of the Convuncertainty for indicated target tissue parameters. °AiphafDepth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for the frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: Z16—9725 1 Page s of11

Add: No.51 Xueyuan Road, Haidian Distict, Belng, 100191, China Tel: «#6—10—62304633—2218 Fac +86—10—42304633—2200 E—mail: ctl@chinatl.com Hitpohewwcchinatt on DASY/EASY — Parameters of Probe: EX3DV4 — SN: 3846 Calibration Parameter Determined in Body Tissue Simulating Media s t pae® P;::"::“,';y . c°""(;,°:‘)'fy ConvF X Conv¥ Conve Z Alpha® r‘;‘:::; :::;‘ To s55 0.% ase ase s0s 040 oss £12% 200 s5.0 105 ase asr ose or1 123 £12% 1450 540 1.30 sz s22 s22 o12 136 |+12% 1750 534 149 7so 1so 7so oz2e 100 £12% 1900 sas 152 Tsr 1sr 1st ois 126 |+12% 2100 sa2 162 Tes res 1es oir 186 +12% 2300 520 181 Tss Tss 155 os2 ore £12% 2450 527 195 Ta 731 131 oss oss +12% 2600 525 216 72s 12s 125 oss o| £12% s250 4s 536 ass a0s 495 oso 155| £13% 5600 48.5 5.77 4.18 4.18 4.18 0.55 160| +13% s750 483 5.04 ass ass 453 oss 198 |+13% © Frequency validty above 300 MHz of +100MHz only applies for DASY v4.4 and higher (Page 2), else it is restricted to #50MHz. The uncertainty is the RSS of ConvF uncertainty at calbration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to : 110 MHz. "Atfrequency below 3 GHz, the validty of tissue paramaters (€ and 0) can be relaxed to £10% if iquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validty of tissue parameters (c and 0)is restricted to £5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters ° AlphalDepth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for the frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: Z16—97251 Page 6 of 11

" in Colsborationwith TTL a CAuBRATIoN LaBorAroRy Add: No.51 Xueyuan Road, Haidian Distict,Beiing, 100191, China Tel: +86—10—62304638—2218 Faxc +86—10—2304633—2200 E—mail: tl@chinat.com 4 in Frequency Response of E—Field (TEM—Cell: ifi110 EXX, Waveguide: R22) 1.5 14 Frequency response (normalized) 13 12 1.1 1.0 0.9 0.8 T 0 500 1000 1500 2000 2500 3000 f [MHz TEM Miiz} &_ Uncertainty of Frequency Response of E—field: £7.5% (k=2) Certificate No: Z16—97251 Page 7 of 11

Add: No.51 Xueyuan Road, Haidian Distrit, Beling, 100191, China Tel: +86—10—62304633—2218 Tc +86—100230463302200 E—mail:cxl@chinatt.com xt inatl on Receiving Pattern (®), 0=0° f=600 MHz, TEM f=1800 MHz, R22 00 Aem ne enentiminines ind titcm—4mmo9cgp as 4 i i i j t t t t v t —1s0 «190 so o so 100 1s0 (~+ — 100Mz > 600MAz + 1800MHz * 2500MHz] Uncertainty of Axial Isotropy Assessment: £0.9% (k=2) Certificate No: 216—97251 Page 8 of 11

Add:No.S1 Xueyuan Road, Haidian Distict, Bjng, 100191, China Tels +86—10—62304633—2218 Fac +86—10—62304600—2200 E—mail:ci@chinait.com Utpshnverchinaen Dynamic Range f(SARneaq) (TEM cell, f = 900 MHz) 1054 g 10° 4 C & ® i 3 04 2 £ 10‘ 4 10‘ i T y 1 10° 10° 10° 10‘ 10° 10 SAR[mW/cm‘] CHWJnot compensated ~#~ compensated Error|dB] t t +—* r— 10 10‘ 1 o‘ 10 10‘ SAR[mWicm ot compensated * compensated Uncertainty of Linearity Assessment: £0.9% (k=2) Certificate No: Z16—97251 Page 9 of 11

* in Colaboration with TTL CALBRATON a LABORATORY Add: No.S1 Xueyuan Road, Haidian Distict, Beiing,100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2200 E—mail:ctl@chinat.com Htiponwchinat.en Conversion Factor Assessment £=900 MHz, WGLS R9(H_convF) =1750 MHz, WGLS R22(H_convF) is |— ———— ja — o 10 os as 2A 10 —om om «o oz o om on ow om 10 Uncertainty of Spherical Isotropy Assessment: £2.8% (K=2) Certificate No: Z16—9725 1 Page 10 of 11

@ I;Cohbonfianwim a CAuBRATION LAsoRATORY Add:No.51 Xueyuan Road, Haidian District, Beljng, 100191, China Tels +86—10—62304633—2218 Fac +86—1062304003—2200 E—mail: tl@chinant.com Mip:wowwchinatl.en DASY/EASY — Parameters of Probe: EX3DV4 — SN: 3846 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 47.9 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disable Probe Overall Length 337mm Probe Body Diameter 10mm Tip Length 9mm Tip Diameter 2.6mm Probe Tip to Sensor X Calibration Point 1mm Probe Tip to Sensor Y Calibration Point 1mm Probe Tip to Sensor Z Calibration Point 1mm Recommended Measurement Distancefrom Surface 1.4mm Certificate No: Z16—9725 1 Page 11 of 11

No. I17Z62297-SEM01 Page 126 of 166 ANNEX H Dipole Calibration Certificate 835 MHz Dipole Calibration Certificate ©Copyright. All rights reserved by CTTL.

® Calibration 4 Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzeriand Accredted by the Swiss Accredtation Sorvice (SAS) s Sehweizerischer Kallbrierdienst q Service suisse i‘étatonnage Servitio svizzoro di taratura 5. swiss Caltbration Service Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the aignatories to the EA Multlateral Agroomantfor the recogn‘tion ofcallration certfieatos Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z NA not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)®, July 2016 c IEC 62209—2, "Procedureto determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)®, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95% . Certficate No: DB3V2—40060_Jut7 Page 2 of 8

Measurement Conditions DASY system confiquration, as far as not given on page 1. DASY Version Dasys vse.100 Extrapolation Advanced Extrapolation Phantom Medular Fiat Phantom Distance Dipole Gnter — TSL 15 mm with Spacer Zoom Sean Resolution t dy, dz ~5 mm Frequency 805 MHza 1 MHz Head TSL parameters The following paramaters and calculations were applied. Temperature Permittivity Conduetivity Nominal Head TSL parameters 220°0 415 0.90 mhoim Measured Head TSL parameters @20 02)°C 40826 % 0.91 mhoim6% Head TSL temperature change during test <o5°c m SAR result with Head TSL SAR averaged over 1 om(1 g) of Head TSL Conditin SAR measured 250 mW input power 297 Who SAR for nominal Head TSL parameters normalized to 1W 9.37 Whg = 17.0 % (ke2) SAR averaged over 10 em(10 g) of Head TSL condition SAR measured 250 mW input power 158 Wha SAR for nominal Head TSL paramsters normalized to 1W 6.06 Wikg =16.5 % (k=2) Body TSL parameters The following parameters and calculations were apolied. Temperature Permitivity Conductivity Nominal Body TSL parameters 22.0°C 562 0.87 mhoim Measured Body TSL parameters gao02)°C 54626% 1.01 mhoim6% Body TSL temperature change during test <05°C ~— SAR result with Body TSL SAR averaged over 1 om? (1 g) of Body TSL Gondition SAR measured 250 mW input power 243 Whg SAR for nominal Body TSL parameters normalized to 1W 8.41 Whkg 2 17.0 % (k=2) SAR averaged over 10 cm? (10 g) of Body TSL condition SAR measured 250 mW input power 157 whg SAR for nominal Body TSL parametars normalized to 1W 6.12 Wikg 2 16.5 % (k=2) Certficate No: DB35V2—40060_Jut17 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point sein—12j0 Retum Loss ~$2.4 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 479n—3.0 n Retum Loss —25.9 0B General Antenna Parameters and Design [Electrical Detay (one direction) | 1302 ns Alfter long term use with 100W radiated power, only a sight warming of the dipole near the feedpoint can be measured The dipole is made of standard sermiigid coaxial cable. The center conductor of the feeding line is direcy connected to the second arm ofthe dipole. The antenna is therefore shor:—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching whon loaded according to the position as explained in the ‘Measurement Condiions* paragraph. The SAR data are not affected by this change. The overall dipole length is stll according to the Standard. No excessive force must be applled to the dipole arms, because they might bnd or the soldered connections noar the feedpoint may be damaged. Additional EUT Data Menutactured by sraag Menufactured on November 09, 2007 Certficate No: DB3SV2—44069_Ju17 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 19.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:40069 Communication System: UTD 0 — CW; Frequency: 835 MHz Medium parameters used: (=835 MHz: a=0.91 S/m; &= 40.8; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEEAIEC/ANST C63.19—201 1 DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(10.07, 10.07, 10.07); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 4.9 (front); Type: QD OOL P49 AA; Serial: 1001 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=3mm, dy=5mm, dz=5mm Reference Value = 62.08 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 3.65 W/kg SAR(L g) =2.37 W/kgs SAR(IO g) = 1.53 Wikg Maximum value of SAR (measured) = 3.21 Wke dB 0 —2.20 ~4.40 —6.60 —80.00 +11.00 0 dB =3.21 Wikg = 5.07 dBWike Certficate No: De3SV2—40060_Jut7 Page 5 of 8

Impedance Measurement Plot for Head TSL 19 w 2eir. coiseres san i uis u samse rirsee d6241pr #35.000 ac0 nz * * Sthet cas.o00 one nine Sto 1 aa5.000 s00 mz Cortficate No: DB3SV2—44069.Jult7 Page 6 of 8

( DASY5 Validation Report for Body TSL Test Laboratory: SPEAG, Zurich, Switzerland Date: 19.07,2017 DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:44069 Communication System: UID 0 — CW: Frequency: 835 MHz Medium parameters used: {= 835 MHz; a = 1.01 S/m; e; = 54.8; p = 1000 kg/m Phantom section: Flat Section Measurement Standard: DASY5 (TEEE/AIEC/ANST C63,19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(10.2, 10.2, 10.2); Calibrated: 31.05.2017; + Sensor—Surface: 1.4mm(Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 4.9 (Back); Type: QD 0OR P49 AA; Scrial: 1005 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW , d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurementgrid: dx=3mm, dy=Smm, d=5mm Reference Value = 59.35 V/m; Power Drift =—0.03 dB Peak SAR (extrapolated) = 3.67 Wikg SAR(L g) =2.43 W/kg; SAR(IO g) = .57 Wike Maximum value of SAR (measured) .22 whke dB 0 2.20 ~4.40 —11.00 0 dB =3.22 Wike= 5.08 dBWike Cortficate No: DB3SV2—44060_.Jult? Page 7 of 8

* t = TTL F mm ~ Impedance Measurement Plot for Body TSL 18 aar ceir osierse Exn sa i u‘rs mamosse —assz5n «0sts pF a35.000 o00 nuz * ve1 +7~.3 c PS is \ s cue ca ma Stakt saz.o00 ooo nez sroe 1 eas.c00 s00 mz Certficate No: DB35V2—44060_Jult7 Page 8 of 8

Calibration Laboratory of «9 sn Schwoizeriachor Kallorierdienst © o ® )€E Schmid & Partner », Service suisse «‘étalonnage Engineering AG Serviclo sviezoro dl taratura o Zeughausstrasse 43, 8004 Zurich, Suitzeriand ihien haad® Swiss Calibration Service Accredtad by the Siss Accreditaion Sorvice (GAS) Acereditation N : SCs 0108 The Swiss Accreditation Service is one ofthe signatories tothe EA MultLateral Agreemontfor the recognion ot callration corificates Client CTTL—BJ (Auden) Cerificate No: D1750V2—1003_Jul17 |CALIBRATION CERTIFICATE Object D1750V2 — SN:1008 Calbration procedure(e) QA CAL—O5.19 Calibration procedure for dipole validation kits above 700 MHz Calbration date: July 21, 2017 Thiscaibvaton cerficate documents th traceabityto natlonalstandards, which reaize the physical ts of measurements(S1. The measremonts and the uncrtantes wih confdence probabily are gven on the folowing pages and are pa of he corifeate. Allcalbrations have beanconducted in the clased aboratar faity: anvronment temperature(223)°C and hunidity <70%. Caltration Equipment used (MATE crtealfr catraton) Pimary Standards CB Gal Date (Conticate No Soeduled Caltration Poner meter NBP sn: rorrre ocAp—17 (No. 217—cesevrsen) Aocie Power sensor NRP—281 sht tosoes oeAper? (No. atz—caset) Apers Power sersor NRP—201 sn: rooms dcApe—7 (No. 217.00520) Apers Raference 20 0B Attrator sh: sose (209 0r—apet7 (No.217—00820) Aprrs Type—N mismatch combination SN:5047.2/00027 Or—Ap—t7 (No.217—02509) Apers Reterence Probe EX3DV4 sn: ros 3t—May—17 (No. EX3—7340Mayt?) May—1s page Sz or 26Mar—17 (No. DAE+—001_Mart?) Maris Secondary Standards e Check Date (n house) Soheduled Check Poer meter EPM—442A SN: GBsrd8o70 0rOct18 (nhousecheck Oct18) in house check Oct18 Power sensor HP 8481A Sh: Ussrzeeres 070ct18 (n housecheck Oct18) In house check: Oct18 Power sensor HP 8481A SN: ivatoneat? 070ct18 (nhousecheck Oct16) In house cheok: Oct18 AF generater nSMT—0 sht tooore 15—jun—15 (n house check Oct16) In house checic Oct18 Network Anatyzer HP 8758E sn ussrasoses 1EOct0f (inhousecheckOct18) In house chedc Oot17 Name Function Signature Calbrated by: Michaot Wobr Laboretoy Technician 1&. Approved by: Katia Pokovie Techrical Manager Ee Issuedt Juty 24, 2017 Thiscaibrationcorficale shallno be repreduced excopt in ful wthout witten approval of thelaboratoy. Certficate No: D1750¥2—1008_Jult? Page 1 of 8


Document Created: 2018-03-06 16:45:26
Document Modified: 2018-03-06 16:45:26
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC